1
|
Oku Y, Nakajima N, Hamada M, Koyama Y. Dansylated Nitrile N-Oxide as the Fluorescent Dye Clickable to Unsaturated Bonds without Catalyst. Chemistry 2024; 30:e202400092. [PMID: 38311590 DOI: 10.1002/chem.202400092] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/09/2024] [Revised: 02/02/2024] [Accepted: 02/04/2024] [Indexed: 02/06/2024]
Abstract
Fluorescent polymeric materials have been exploited in the fields of aesthetical purposes, biomedical engineering, and three-dimensional printing applications. While the fluorescent materials are prepared by the polymerization of fluorescent monomer or the blending a fluorescent dye with common polymer, the covalent immobilization of fluorescent dye onto common polymers is not the practical technique. In this paper, dansylated nitrile N-oxide (Dansyl-NO) has been designed and synthesized to be a stable nitrile N-oxide as the derivative of 2-hydroxy-1-naphthaldehyde. While Dansyl-NO shows good reactivity to an alkene and an alkyne to give fluorescent Dansyl-Ene and Dansyl-Yne, respectively, it hardly reacts to a nitrile. The results indicate that Dansyl-NO serves as a fluorescent dye clickable to alkenes and alkynes. To know the effects of solvent on the fluorescent properties, the UV-vis and fluorescence spectra of Dansyl-Ene are measured in three solvents. Dansyl-Ene shows fluorescent solvatochromism, which appears to be red-shifted along with the increase in solvent polarity. Poly(styrene-co-butadiene) directly reacts with Dansyl-NO to give fluorescent modified SB. The emission spectrum of modified SB is blue-shifted compared with that of Dansyl-Ene. The blue-shift could be possibly attributed to the presence of less polar polymer skeleton around the dansyl moieties of modified SB.
Collapse
Affiliation(s)
- Yuki Oku
- Department of Pharmaceutical Engineering, Toyama Prefectural University, 5180 Kurokawa, Imizu, Toyama 939-0398, Japan
| | - Noriyuki Nakajima
- Department of Pharmaceutical Engineering, Toyama Prefectural University, 5180 Kurokawa, Imizu, Toyama 939-0398, Japan
- Biotechnology Research Center, Toyama Prefectural University, 5180 Kurokawa, Imizu, Toyama 939-0398, Japan
| | - Masahiro Hamada
- Department of Pharmaceutical Engineering, Toyama Prefectural University, 5180 Kurokawa, Imizu, Toyama 939-0398, Japan
- Biotechnology Research Center, Toyama Prefectural University, 5180 Kurokawa, Imizu, Toyama 939-0398, Japan
| | - Yasuhito Koyama
- Department of Pharmaceutical Engineering, Toyama Prefectural University, 5180 Kurokawa, Imizu, Toyama 939-0398, Japan
- Biotechnology Research Center, Toyama Prefectural University, 5180 Kurokawa, Imizu, Toyama 939-0398, Japan
| |
Collapse
|
2
|
Chiappone A, Roppolo I, Scavino E, Mogli G, Pirri CF, Stassi S. Three-Dimensional Printing of Triboelectric Nanogenerators by Digital Light Processing Technique for Mechanical Energy Harvesting. ACS APPLIED MATERIALS & INTERFACES 2023; 15:53974-53983. [PMID: 37945515 PMCID: PMC10685350 DOI: 10.1021/acsami.3c13323] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 09/06/2023] [Revised: 10/26/2023] [Accepted: 10/30/2023] [Indexed: 11/12/2023]
Abstract
Triboelectric nanogenerators (TENGs) represent intriguing technology to harvest human mechanical movements for powering wearable and portable electronics. Differently, compared to conventional fabrication approaches, additive manufacturing can allow the fabrication of TENGs with good dimensional resolution, high reproducibility, and quick production processes and, in particular, the obtainment of complex and customized structures. Among 3D printing technologies, digital light processing (DLP) is well-known for being the most flexible to produce functional devices by controlling both the geometry and the different ingredients of printable resins. On the other hand, DLP was not exploited for TENG fabrication, and consequently, the knowledge of the performance of 3D printable materials as charge accumulators upon friction is limited. Here, the application of the DLP technique to the 3D printing of triboelectric nanogenerators is studied. First, several printable materials have been tested as triboelectric layers to define a triboelectric series of DLP 3D printable materials. Then, TENG devices with increased geometrical complexity were printed, showcasing the ability to harvest energy from human movement. The method presented in this work illustrates how the DLP may represent a valuable and flexible solution to fabricate triboelectric nanogenerators, also providing a triboelectric classification of the most common photocurable resins.
Collapse
Affiliation(s)
- Annalisa Chiappone
- Department
of Chemical and Geological Sciences, Università
degli studi di Cagliari, Cittadella Universitaria Blocco D, S.S. 554 bivio per Sestu, Monserrato, CA 09042, Italy
| | - Ignazio Roppolo
- Department
of Applied Science and Technology, Politecnico
di Torino, C.so Duca degli Abruzzi 24, Turin 10129, Italy
- Center
for Sustainable Future Technologies @Polito, Istituto Italiano di Tecnologia, Via Livorno, 60, Turin 10144, Italy
| | - Edoardo Scavino
- Department
of Applied Science and Technology, Politecnico
di Torino, C.so Duca degli Abruzzi 24, Turin 10129, Italy
| | - Giorgio Mogli
- Department
of Applied Science and Technology, Politecnico
di Torino, C.so Duca degli Abruzzi 24, Turin 10129, Italy
| | - Candido Fabrizio Pirri
- Department
of Applied Science and Technology, Politecnico
di Torino, C.so Duca degli Abruzzi 24, Turin 10129, Italy
- Center
for Sustainable Future Technologies @Polito, Istituto Italiano di Tecnologia, Via Livorno, 60, Turin 10144, Italy
| | - Stefano Stassi
- Department
of Applied Science and Technology, Politecnico
di Torino, C.so Duca degli Abruzzi 24, Turin 10129, Italy
| |
Collapse
|
3
|
Ahmed I, Ali M, Elsherif M, Butt H. UV polymerization fabrication method for polymer composite based optical fiber sensors. Sci Rep 2023; 13:10823. [PMID: 37402807 DOI: 10.1038/s41598-023-33991-6] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/16/2023] [Accepted: 04/21/2023] [Indexed: 07/06/2023] Open
Abstract
Optical fiber (OF) sensors are critical optical devices with excellent sensing capabilities and the capacity to operate in remote and hostile environments. However, integrating functional materials and micro/nanostructures into the optical fiber systems for specific sensing applications has limitations of compatibility, readiness, poor control, robustness, and cost-effectiveness. Herein, we have demonstrated the fabrication and integration of stimuli-responsive optical fiber probe sensors using a novel, low-cost, and facile 3D printing process. Thermal stimulus-response of thermochromic pigment micro-powders was integrated with optical fibers by incorporating them into ultraviolet-sensitive transparent polymer resins and then printed via a single droplet 3D printing process. Hence, the thermally active polymer composite fibers were grown (additively manufactured) on top of the commercial optical fiber tips. Then, the thermal response was studied within the temperature range of (25-35 °C) and (25-31 °C) for unicolor and dual color pigment powders-based fiber-tip sensors, respectively. The unicolor (with color to colorless transition) and dual color (with color to color transition) powders-based sensors exhibited substantial variations in transmission and reflection spectra by reversibly increasing and decreasing temperatures. The sensitivities were calculated from the transmission spectra where average change in transmission spectra was recorded as 3.5% with every 1 °C for blue, 3% for red and 1% for orange-yellow thermochromic powders based optical fiber tip sensors. Our fabricated sensors are cost-effective, reusable, and flexible in terms of materials and process parameters. Thus, the fabrication process can potentially develop transparent and tunable thermochromic sensors for remote sensing with a much simpler manufacturing process compared to conventional and other 3D printing processes for optical fiber sensors. Moreover, this process can integrate micro/nanostructures as patterns on the optical fiber tips to increase sensitivity. The developed sensors may be employed as remote temperature sensors in biomedical and healthcare applications.
Collapse
Affiliation(s)
- Israr Ahmed
- Department of Mechanical Engineering, Khalifa University of Science and Technology, Abu Dhabi, 127788, UAE
| | - Murad Ali
- Department of Mechanical Engineering, Khalifa University of Science and Technology, Abu Dhabi, 127788, UAE.
| | | | - Haider Butt
- Department of Mechanical Engineering, Khalifa University of Science and Technology, Abu Dhabi, 127788, UAE.
| |
Collapse
|
4
|
Salas A, Zanatta M, Sans V, Roppolo I. Chemistry in light-induced 3D printing. CHEMTEXTS 2023. [DOI: 10.1007/s40828-022-00176-z] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/22/2023]
Abstract
AbstractIn the last few years, 3D printing has evolved from its original niche applications, such as rapid prototyping and hobbyists, towards many applications in industry, research and everyday life. This involved an evolution in terms of equipment, software and, most of all, in materials. Among the different available 3D printing technologies, the light activated ones need particular attention from a chemical point of view, since those are based on photocurable formulations and in situ rapid solidification via photopolymerization. In this article, the chemical aspects beyond the preparation of a formulation for light-induced 3D printing are analyzed and explained, aiming at giving more tools for the development of new photocurable materials that can be used for the fabrication of innovative 3D printable devices.
Graphical abstract
Collapse
|
5
|
Continuous resin refilling and hydrogen bond synergistically assisted 3D structural color printing. Nat Commun 2022; 13:7095. [DOI: 10.1038/s41467-022-34866-6] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/16/2022] [Accepted: 11/10/2022] [Indexed: 11/21/2022] Open
Abstract
Abstract3D photonic crystals (PCs) have attracted extensive attention due to their unique optical properties. However, fabricating 3D PCs structure by 3D printing colloidal particles is limited by control of assembly under a fast-printing speed. Here, we employ continuous digital light processing (DLP) 3D printing strategy with hydrogen bonds assisted colloidal inks for fabricating well-assembled 3D PCs structures. Stable dispersion of colloidal particles inside UV-curable system induced by hydrogen bonding and suction force induced by continuous curing manner cooperatively realize the simultaneous macroscopic printing and microscopic particle assembly, which endows volumetric color property. Structural color can be well regulated by controlling the particle diameter and printing speed, through which various complex 3D structures with desired structural color distribution and optical light-guide properties are acquired. This 3D color construction approach shows great potential in customized jewelry accessories, decoration and optical device preparation, and will innovate the development of structural color.
Collapse
|
6
|
Sheng L, Li M, Zheng S, Qi J. Adjusting the accuracy of PEGDA-GelMA vascular network by dark pigments via digital light processing printing. J Biomater Appl 2021; 36:1173-1187. [PMID: 34738507 DOI: 10.1177/08853282211053081] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/16/2022]
Abstract
Vascularization is one of the most important factors greatly influencing scaffold regeneration. In this study, a precise network of hollow vessels was printed by digital light processing (DLP) with poly(ethylene glycol) diacrylate (PEGDA)/gelatin-methacryloyl (GelMA), and dark pigmentation absorbers were added to ensure printing accuracy. First, the compound bio-inks of the PEGDA-GelMA hydrogel were prepared for direct vascular printing, and a high-precision DLP system was established. Second, the printing effects of three dark absorbers, namely, nigrosin, brilliant black, and brilliant blue, on the x-, y-, and z-axes were studied. By printing models with different densities, it was determined that 0.2% nigrosin, 0.1% brilliant black, and 0.3% brilliant blue had better effects on the x- and y-axes accuracy, and the absorbance of the absorbers played a decisive role in adjusting the accuracy. Additionally, to solve the problem of uneven curing on the upper and lower surfaces caused by the addition of an absorber with high absorbance, a model of the difference in curing width between the upper and lower surfaces of a unit-layer slice based on high-absorbance absorbers was established, and the reference value for the slice thickness was calculated. Third, the biological and mechanical properties of the bio-inks were verified with scanning electron microscopy and Fourier transform infrared, and by tensile, swelling, degradation, and cytotoxicity tests on different concentrations of PEGDA-GelMA hydrogel and absorbers. The results showed that 30% PEGDA-7% GelMA/0.1% brilliant black was the optimal preparation to print a hollow vascular network. The error of the printing tube wall and cavity was between 1% and 3%, which demonstrates the high precision of the method. Human umbilical vein endothelial cells were planted in the lumen, and the survival rate achieved 107% on the seventh day, demonstrating the good biocompatibility of the composite hydrogel.
Collapse
Affiliation(s)
- Lin Sheng
- 12605Tianjin Key Laboratory of Equipment Design and Manufacturing Technology, School of Mechanical Engineering, Tianjin University, Tianjin, China
| | - Mo Li
- 12605Tianjin Key Laboratory of Equipment Design and Manufacturing Technology, School of Mechanical Engineering, Tianjin University, Tianjin, China
| | - Shuxian Zheng
- 12605Tianjin Key Laboratory of Equipment Design and Manufacturing Technology, School of Mechanical Engineering, Tianjin University, Tianjin, China
| | - Jian Qi
- 66270School of Mechanical Engineering, Tianjin University of Technology and Education, China
| |
Collapse
|
7
|
Merazzo KJ, Lima AC, Rincón-Iglesias M, Fernandes LC, Pereira N, Lanceros-Mendez S, Martins P. Magnetic materials: a journey from finding north to an exciting printed future. MATERIALS HORIZONS 2021; 8:2654-2684. [PMID: 34617551 DOI: 10.1039/d1mh00641j] [Citation(s) in RCA: 7] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/13/2023]
Abstract
The potential implications/applications of printing technologies are being recognized worldwide across different disciplines and industries. Printed magnetoactive smart materials, whose physical properties can be changed by the application of external magnetic fields, are an exclusive class of smart materials that are highly valuable due to their magnetically activated smart and/or multifunctional response. Such smart behavior allows, among others, high speed and low-cost wireless activation, fast response, and high controllability with no relevant limitations in design, shape, or dimensions. Nevertheless, the printing of magnetoactive materials is still in its infancy, and the design apparatus, the material set, and the fabrication procedures are far from their optimum features. Thus, this review presents the main concepts that allow interconnecting printing technologies with magnetoactive materials by discussing the advantages and disadvantages of this joint field, trying to highlight the scientific obstacles that still limit a wider application of these materials nowadays. Additionally, it discusses how these limitations could be overcome, together with an outlook of the remaining challenges in the emerging digitalization, Internet of Things, and Industry 4.0 paradigms. Finally, as magnetoactive materials will play a leading role in energy generation and management, the magnetic-based Green Deal is also addressed.
Collapse
Affiliation(s)
- K J Merazzo
- BCMaterials, Basque Center for Materials, Applications and Nanostructures, UPV/EHU Science Park, 48940 Leioa, Spain
| | - A C Lima
- Centro/Departamento de Física, Universidade do Minho, 4710-057 Braga, Portugal.
- INL - International Iberian Nanotechnology Laboratory, 4715-330 Braga, Portugal
| | - M Rincón-Iglesias
- BCMaterials, Basque Center for Materials, Applications and Nanostructures, UPV/EHU Science Park, 48940 Leioa, Spain
| | - L C Fernandes
- Centro/Departamento de Física, Universidade do Minho, 4710-057 Braga, Portugal.
| | - N Pereira
- Centro/Departamento de Física, Universidade do Minho, 4710-057 Braga, Portugal.
- Algoritmi Center, Minho University, 4800-058 Guimarães, Portugal
| | - S Lanceros-Mendez
- BCMaterials, Basque Center for Materials, Applications and Nanostructures, UPV/EHU Science Park, 48940 Leioa, Spain
- IKERBASQUE, Basque Foundation for Science, 48009 Bilbao, Spain.
| | - P Martins
- Centro/Departamento de Física, Universidade do Minho, 4710-057 Braga, Portugal.
- IB-S Institute of Science and Innovation for Sustainability, Universidade do Minho, 4710-057, Braga, Portugal
| |
Collapse
|
8
|
Kingsborough RP, Wrobel AT, Kunz RR. Colourimetry for the sensitive detection of vapour-phase chemicals: State of the art and future trends. Trends Analyt Chem 2021. [DOI: 10.1016/j.trac.2021.116397] [Citation(s) in RCA: 3] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/18/2022]
|
9
|
Abstract
Abstract
3D printing belongs to the emerging technologies of our time. Describing diverse specific techniques, 3D printing enables rapid production of individual objects and creating shapes that would not be produced with other techniques. One of the drawbacks of typical 3D printing processes, however, is the layered structure of the created parts. This is especially problematic in the production of optical elements, which in most cases necessitate highly even surfaces. To meet this challenge, advanced 3D printing techniques as well as other sophisticated solutions can be applied. Here, we give an overview of 3D printed optical elements, such as lenses, mirrors, and waveguides, with a focus on freeform optics and other elements for which 3D printing is especially well suited.
Collapse
Affiliation(s)
- Tomasz Blachowicz
- Silesian University of Technology, Institute of Physics – Center for Science and Education , 44-100 Gliwice , Poland
| | - Guido Ehrmann
- Virtual Institute of Applied Research on Advanced Materials (VIARAM) , 33619 Bielefeld , Germany
| | - Andrea Ehrmann
- Bielefeld University of Applied Sciences, Faculty of Engineering and Mathematics , 33619 Bielefeld , Germany
| |
Collapse
|
10
|
Functional 3D printing: Approaches and bioapplications. Biosens Bioelectron 2020; 175:112849. [PMID: 33250333 DOI: 10.1016/j.bios.2020.112849] [Citation(s) in RCA: 51] [Impact Index Per Article: 12.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/30/2020] [Revised: 10/28/2020] [Accepted: 11/22/2020] [Indexed: 12/17/2022]
Abstract
3D printing technology has become a mature manufacturing technique, widely used for its advantages over the traditional methods, such as the end-user customization and rapid prototyping, useful in different application fields, including the biomedical one. Indeed, it represents a helpful tool for the realization of biodevices (i.e. biosensors, microfluidic bioreactors, drug delivery systems and Lab-On-Chip). In this perspective, the development of 3D printable materials with intrinsic functionalities, through the so-called 4D printing, introduces novel opportunities for the fabrication of "smart" or stimuli-responsive devices. Indeed, functional 3D printable materials can modify their surfaces, structures, properties or even shape in response to specific stimuli (such as pressure, temperature or light radiation), adding to the printed object new interesting properties exploited after the fabrication process. In this context, by combining 3D printing technology with an accurate materials' design, functional 3D objects with built-in (bio)chemical functionalities, having biorecognition, biocatalytic and drug delivery capabilities are here reported.
Collapse
|
11
|
González G, Baruffaldi D, Martinengo C, Angelini A, Chiappone A, Roppolo I, Pirri CF, Frascella F. Materials Testing for the Development of Biocompatible Devices through Vat-Polymerization 3D Printing. NANOMATERIALS (BASEL, SWITZERLAND) 2020; 10:E1788. [PMID: 32916902 PMCID: PMC7559499 DOI: 10.3390/nano10091788] [Citation(s) in RCA: 25] [Impact Index Per Article: 6.3] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 08/11/2020] [Revised: 09/06/2020] [Accepted: 09/07/2020] [Indexed: 12/21/2022]
Abstract
Light-based 3D printing techniques could be a valuable instrument in the development of customized and affordable biomedical devices, basically for high precision and high flexibility in terms of materials of these technologies. However, more studies related to the biocompatibility of the printed objects are required to expand the use of these techniques in the health sector. In this work, 3D printed polymeric parts are produced in lab conditions using a commercial Digital Light Processing (DLP) 3D printer and then successfully tested to fabricate components suitable for biological studies. For this purpose, different 3D printable formulations based on commercially available resins are compared. The biocompatibility of the 3D printed objects toward A549 cell line is investigated by adjusting the composition of the resins and optimizing post-printing protocols; those include washing in common solvents and UV post-curing treatments for removing unreacted and cytotoxic products. It is noteworthy that not only the selection of suitable materials but also the development of an adequate post-printing protocol is necessary for the development of biocompatible devices.
Collapse
Affiliation(s)
- Gustavo González
- Dipartimento di Scienza Applicata e Tecnologia, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Turin, Italy; (G.G.); (D.B.); (C.M.); (A.C.); (I.R); (C.F.P.)
- Center for Sustainable Futures @Polito, Istituto Italiano di Tecnologia, Via Livorno 60, 10144 Turin, Italy
| | - Désirée Baruffaldi
- Dipartimento di Scienza Applicata e Tecnologia, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Turin, Italy; (G.G.); (D.B.); (C.M.); (A.C.); (I.R); (C.F.P.)
- PolitoBIOMed Lab, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Turin, Italy
| | - Cinzia Martinengo
- Dipartimento di Scienza Applicata e Tecnologia, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Turin, Italy; (G.G.); (D.B.); (C.M.); (A.C.); (I.R); (C.F.P.)
- PolitoBIOMed Lab, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Turin, Italy
| | - Angelo Angelini
- Advanced Materials Metrology and Life Sciences Division, Istituto Nazionale di Ricerca Metrologica, Strada delle Cacce 91, 10135 Torino, Italy;
| | - Annalisa Chiappone
- Dipartimento di Scienza Applicata e Tecnologia, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Turin, Italy; (G.G.); (D.B.); (C.M.); (A.C.); (I.R); (C.F.P.)
- PolitoBIOMed Lab, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Turin, Italy
| | - Ignazio Roppolo
- Dipartimento di Scienza Applicata e Tecnologia, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Turin, Italy; (G.G.); (D.B.); (C.M.); (A.C.); (I.R); (C.F.P.)
- PolitoBIOMed Lab, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Turin, Italy
| | - Candido Fabrizio Pirri
- Dipartimento di Scienza Applicata e Tecnologia, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Turin, Italy; (G.G.); (D.B.); (C.M.); (A.C.); (I.R); (C.F.P.)
- Center for Sustainable Futures @Polito, Istituto Italiano di Tecnologia, Via Livorno 60, 10144 Turin, Italy
- PolitoBIOMed Lab, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Turin, Italy
| | - Francesca Frascella
- Dipartimento di Scienza Applicata e Tecnologia, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Turin, Italy; (G.G.); (D.B.); (C.M.); (A.C.); (I.R); (C.F.P.)
- PolitoBIOMed Lab, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Turin, Italy
| |
Collapse
|
12
|
Light Processable Starch Hydrogels. Polymers (Basel) 2020; 12:polym12061359. [PMID: 32560332 PMCID: PMC7362200 DOI: 10.3390/polym12061359] [Citation(s) in RCA: 25] [Impact Index Per Article: 6.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/15/2020] [Revised: 06/09/2020] [Accepted: 06/12/2020] [Indexed: 01/08/2023] Open
Abstract
Light processable hydrogels were successfully fabricated by utilizing maize starch as raw material. To render light processability, starch was gelatinized and methacrylated by simple reaction with methacrylic anhydride. The methacrylated starch was then evaluated for its photocuring reactivity and 3D printability by digital light processing (DLP). Hydrogels with good mechanical properties and biocompatibility were obtained by direct curing from aqueous solution containing lithium phenyl-2,4,6-trimethylbenzoylphosphinate (LAP) as photo-initiator. The properties of the hydrogels were tunable by simply changing the concentration of starch in water. Photo-rheology showed that the formulations with 10 or 15 wt% starch started curing immediately and reached G' plateau after only 60 s, while it took 90 s for the 5 wt% formulation. The properties of the photocured hydrogels were further characterized by rheology, compressive tests, and swelling experiments. Increasing the starch content from 10 to 15 wt% increased the compressive stiffness from 13 to 20 kPa. This covers the stiffness of different body tissues giving promise for the use of the hydrogels in tissue engineering applications. Good cell viability with human fibroblast cells was confirmed for all three starch hydrogel formulations indicating no negative effects from the methacrylation or photo-crosslinking reaction. Finally, the light processability of methacrylated starch by digital light processing (DLP) 3D printing directly from aqueous solution was successfully demonstrated. Altogether the results are promising for future application of the hydrogels in tissue engineering and as cell carriers.
Collapse
|
13
|
Chiadò A, Palmara G, Chiappone A, Tanzanu C, Pirri CF, Roppolo I, Frascella F. A modular 3D printed lab-on-a-chip for early cancer detection. LAB ON A CHIP 2020; 20:665-674. [PMID: 31939966 DOI: 10.1039/c9lc01108k] [Citation(s) in RCA: 25] [Impact Index Per Article: 6.3] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/10/2023]
Abstract
A functional polymeric 3D device is produced in a single step printing process using a stereolithography based 3D printer. The photocurable formulation is designed for introducing a controlled amount of carboxyl groups (-COOH), in order to perform a covalent immobilization of bioreceptors on the device. The effectiveness of the application is demonstrated by performing an immunoassay for the detection of protein biomarkers involved in angiogenesis, whose role is crucial in the onset of cancer and in the progressive metastatic behavior of tumors. The detection of angiogenesis biomarkers is necessary for an early diagnosis of the pathology, allowing the employment of a less invasive therapy for the patient. In particular, vascular endothelial growth factor and angiopoietin-2 biomarkers are detected with a limit of detection of 11 ng mL-1 and 0.8 ng mL-1, respectively. This study shows how 3D microfabrication techniques, material characterization, and device development could be combined to obtain an engineered polymeric chip with intrinsic tuned functionalities.
Collapse
Affiliation(s)
- Alessandro Chiadò
- Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, Torino, 10129, Italy.
| | - Gianluca Palmara
- Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, Torino, 10129, Italy.
| | - Annalisa Chiappone
- Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, Torino, 10129, Italy.
| | - Claudia Tanzanu
- Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, Torino, 10129, Italy.
| | - Candido Fabrizio Pirri
- Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, Torino, 10129, Italy. and Center for Sustainable Future Technologies @Polito, Istituto Italiano di Tecnologia, Corso Trento 21, Torino 10129, Italy
| | - Ignazio Roppolo
- Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, Torino, 10129, Italy.
| | - Francesca Frascella
- Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, Torino, 10129, Italy.
| |
Collapse
|
14
|
Gillono M, Chiappone A, Mendola L, Gomez Gomez M, Scaltrito L, Pirri CF, Roppolo I. Study on the Printability through Digital Light Processing Technique of Ionic Liquids for CO 2 Capture. Polymers (Basel) 2019; 11:E1932. [PMID: 31771145 PMCID: PMC6960677 DOI: 10.3390/polym11121932] [Citation(s) in RCA: 4] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/04/2019] [Revised: 11/20/2019] [Accepted: 11/20/2019] [Indexed: 01/23/2023] Open
Abstract
Here we present new 3D printable materials based on the introduction of different commercially available ionic liquids (ILs) in the starting formulations. We evaluate the influence of these additives on the printability of such formulations through light-induced 3D printing (digital light processing-DLP), investigating as well the effect of ionic liquids with polymerizable groups. The physical chemical properties of such materials are compared, focusing on the permeability towards CO2 of the different ILs present in the formulations. At last, we show the possibility of 3D printing high complexity structures, which could be the base of new high complexity filters for a more efficient CO2 capture.
Collapse
Affiliation(s)
- Matteo Gillono
- Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino, Italy; (M.G.); (A.C.); (L.M.); (M.G.G.); (L.S.); (C.F.P.)
- Center for Sustainable Future Technologies @Polito, Istituto Italiano di Tecnologia, Via Livorno 60, 10144 Torino, Italy
| | - Annalisa Chiappone
- Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino, Italy; (M.G.); (A.C.); (L.M.); (M.G.G.); (L.S.); (C.F.P.)
| | - Lorenzo Mendola
- Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino, Italy; (M.G.); (A.C.); (L.M.); (M.G.G.); (L.S.); (C.F.P.)
| | - Manuel Gomez Gomez
- Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino, Italy; (M.G.); (A.C.); (L.M.); (M.G.G.); (L.S.); (C.F.P.)
| | - Luciano Scaltrito
- Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino, Italy; (M.G.); (A.C.); (L.M.); (M.G.G.); (L.S.); (C.F.P.)
| | - Candido Fabrizio Pirri
- Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino, Italy; (M.G.); (A.C.); (L.M.); (M.G.G.); (L.S.); (C.F.P.)
- Center for Sustainable Future Technologies @Polito, Istituto Italiano di Tecnologia, Via Livorno 60, 10144 Torino, Italy
| | - Ignazio Roppolo
- Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino, Italy; (M.G.); (A.C.); (L.M.); (M.G.G.); (L.S.); (C.F.P.)
| |
Collapse
|
15
|
Roppolo I, Frascella F, Gastaldi M, Castellino M, Ciubini B, Barolo C, Scaltrito L, Nicosia C, Zanetti M, Chiappone A. Thiol–yne chemistry for 3D printing: exploiting an off-stoichiometric route for selective functionalization of 3D objects. Polym Chem 2019. [DOI: 10.1039/c9py00962k] [Citation(s) in RCA: 26] [Impact Index Per Article: 5.2] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/21/2022]
Abstract
An alkyne monomer, bis(propargyl) fumarate, is synthesized and mixed to a thiol monomer to produce DLP-3D printable formulations. Using off-stoichiometric formulations it is possible to print functionalizable objects.
Collapse
Affiliation(s)
- Ignazio Roppolo
- Department of Applied Science and Technology DISAT
- Politecnico di Torino
- Torino
- Italy
| | - Francesca Frascella
- Department of Applied Science and Technology DISAT
- Politecnico di Torino
- Torino
- Italy
| | - Matteo Gastaldi
- Department of Chemistry and NIS Centre
- University of Turin
- Torino
- Italy
| | - Micaela Castellino
- Department of Applied Science and Technology DISAT
- Politecnico di Torino
- Torino
- Italy
| | - Betty Ciubini
- Department of Applied Science and Technology DISAT
- Politecnico di Torino
- Torino
- Italy
| | - Claudia Barolo
- Department of Chemistry and NIS Centre
- University of Turin
- Torino
- Italy
| | - Luciano Scaltrito
- Department of Applied Science and Technology DISAT
- Politecnico di Torino
- Torino
- Italy
| | - Carmelo Nicosia
- Department of Electronics and Telecommunications DET
- Politecnico di Torino
- Torino
- Italy
| | - Marco Zanetti
- Department of Chemistry and NIS Centre
- University of Turin
- Torino
- Italy
- ICxT Centre
| | - Annalisa Chiappone
- Department of Applied Science and Technology DISAT
- Politecnico di Torino
- Torino
- Italy
| |
Collapse
|