Influence of Cl Incorporation in Perovskite Precursor on the Crystal Growth and Storage Stability of Perovskite Solar Cells

Bottom-Up Defect Modification Through Oily-Allicin Modified Buried Interface Achieving Highly Efficient and Stable Perovskite Solar Cells

The buried interface properties of the perovskite solar cells (PSCs) play a crucial role in the power conversion efficiency (PCE) and operational stability. The metal-oxide/perovskite heterogeneous interfaces are highly defective and cause serious ion migration. However, the buried and unexposed bottom interface and simultaneous stabilization of grain boundaries receive less attention and effective solutions. To tackle this problem, a solid-liquid strategy is employed by introducing oily-additive allicin at the buried interface to passivate the shallow (VI and Vo) and deep traps (VPb and PbI). Interestingly, oily status allicin fills the pinholes at the heterointerface and wraps the perovskite grains, suppressing the ion migration during the photoaging process. As a result, an outstanding PCE of 25.07% is achieved with a remarkable fill factor (FF) of 84.03%. The modified devices can maintain 94.51% of the original PCE after light soaking under 1-sun illumination for 1000 h. This work demonstrates a buried interface modification method that employs an eco-friendly additive, which helps promote the development of PSCs with high performance and stability.

Highly Efficient Monolithic Perovskite/Perovskite/Silicon Triple-Junction Solar Cells

Wide-bandgap metal halide perovskites have demonstrated promise in multijunction photovoltaic (PV) cells. However, photoinduced phase segregation and the resultant low open-circuit voltage (Voc) have greatly limited the PV performance of perovskite-based multijunction devices. Here, a alloying strategy is reported to achieve uniform distribution of triple cations and halides in wide-bandgap perovskites by doping Rb+ and Cl- with small ionic radii, which effectively suppresses halide phase segregation while promoting the homogenization of surface potential. Based on this strategy, a Voc of 1.33 V is obtained from single-junction perovskite solar cells, and a VOC approaching 3.0 V and a power conversion efficiency of 25.0% (obtained from reverse scan direction, certified efficiency: 24.19%) on an 1.04 cm2 photoactive area can be achieved in a perovskite/perovskite/c-Si triple-junction tandem cell, where the certification efficiency is by far the greatest performance of perovskite-based triple-junction tandem solar cells. This work overcomes the performance deadlock of perovskite-based triple-junction tandem cells by setting a materials-by-design paradigm.

The Synergistic Effect of Additives for Formamidinium-Based Inverted Dion-Jacobson 2D Perovskite Solar Cells with Enhanced Photovoltaic Performance

Two-dimensional (2D) perovskite solar cells (PSCs) have attracted rapid growing attention due to their excellent environmental and operational stability. As an important type of 2D perovskite, Dion-Jacobson (DJ) 2D perovskites exhibit better structural integrity and more stable optoelectronic properties than those of Ruddlesden-Popper (RP) ones because of the elimination of weak van der Waals interactions. Random phase distribution, phase impurity, and weak crystallinity, however, can lead to severe nonradiative recombination losses in 2D perovskites and inferior device stability. Herein, formamidinium chloride (FACl) and lead chloride (PbCl2) are selected as additives to fabricate efficient and stable DJ 2D PSCs. The synergistic effect of additives could efficiently induce crystallization and suppress the low-n phase perovskites. The obtained 2D perovskites exhibit extended charge lifetime and enhanced charge transfer. The corresponding PSC device delivers an efficiency of 16.63% with a significantly improved open-circuit voltage (VOC) of 1.18 V and a fill factor (FF) of 81.65% than the control one. This PCE ranks the highest for inverted FA-based 2D DJ PSCs. Moreover, this device has exhibited exceptional long-term stability, which retains more than 95% of the initial efficiencies at about 50% relative humidity for 600 h.

Enhanced stability of triple-halide perovskites CsPbI3-x-yBrxCly (x and y = 0-0.024): understanding the role of Cl doping from ab initio calculations

Doping of chloride in mixed iodide-bromide perovskites has been shown experimentally to suppress the photo-induced halide-ion segregation and enhance the stability of triple-halide perovskites (THP). However, a fundamental understanding of the effects of Cl doping is yet to be achieved especially when the doping concentration is low. Here we report the results of a state-of-the-art ab initio study of the atomic structure of THP by considering small doping concentrations of Br and Cl in CsPbI3. We find a reduction in the Pb-I bond lengths and tilting of PbI6 octahedra with Cl doping which lead to exothermic heat of mixing and therefore higher stability of THP. Moreover, using quasi-chemical approximation, our results show that there is a very small contribution of configurational entropy to Gibbs free energy at such low doping concentrations and at the operational temperature of 50 °C. This suggests that the favorable heat of mixing value is more important for the stability at low doping concentrations of Cl while a higher concentration of Cl increases the risk of halide segregation. Further calculations on Frenkel defect formation energy of I or Br-interstitial shows that the doping of Cl in I/Br mixed binary-compounds hinders the formation of Frenkel defects. These results support experiments and help to understand the role of chloride in suppressing the halide ion mobility with only a slight increase in the band gap. Accordingly, the THPs manifest a promising pathway for developing single-phase perovskites for solar cells and light-emitting diodes with improved performance and enhanced stability.

Controlled growth of perovskite layers with volatile alkylammonium chlorides

Controlling the crystallinity and surface morphology of perovskite layers by methods such as solvent engineering1,2 and methylammonium chloride addition3-7 is an effective strategy for achieving high-efficiency perovskite solar cells. In particular, it is essential to deposit α-formamidinium lead iodide (FAPbI3) perovskite thin films with few defects due to their excellent crystallinity and large grain size. Here we report the controlled crystallization of perovskite thin films with the combination of alkylammonium chlorides (RACl) added to FAPbI3. The δ-phase to α-phase transition of FAPbI3 and the crystallization process and surface morphology of the perovskite thin films coated with RACl under various conditions were investigated through in situ grazing-incidence wide-angle X-ray diffraction and scanning electron microscopy. RACl added to the precursor solution was believed to be easily volatilized during coating and annealing owing to dissociation into RA0 and HCl with deprotonation of RA+ induced by RA⋯H+-Cl- binding to PbI2 in FAPbI3. Thus, the type and amount of RACl determined the δ-phase to α-phase transition rate, crystallinity, preferred orientation and surface morphology of the final α-FAPbI3. The resulting perovskite thin layers facilitated the fabrication of perovskite solar cells with a power-conversion efficiency of 26.08% (certified 25.73%) under standard illumination.

Doping Strategies for Promising Organic-Inorganic Halide Perovskites

Organic-inorganic halide perovskites (OIHPs) obtained tremendous attention due to their low cost and excellent properties. However, the stability and toxicity of Pb-based OIHPs (POIHPs), as well as the weakness of efficiency and stability in Sn-based OIHPs (SOIHPs), are still serious issues for commercial application. Notably, composition engineering is an effective and direct strategy for improving these issues along with the control and modification of properties. Recently, the doping strategies for POIHPs and SOIHPs are booming. Based on the relationship between properties and composition, the doping strategies for POIHPs and SOIHPs, aiming to provide a comprehensive review and guidance for the research are systematically summarized. Moreover, the doping strategies for Pb-Sn mixed OIHPs are also discussed. Finally, a brief perspective and conclusion toward future possible doping schemes and properties designment of POIHPs and SOIHPs are offered.

Enhancing Performance and Stability of Perovskite Solar Cells through Surface Defect Passivation with Organic Bidentate Lewis Bases

Organic Lewis bases [2,2'-bipyridine (BPY), 4-hydroxy-1,5-naphthyridine-3-carbonitrile (DQCN), and thenoyltrifluoroacetone (TTFA)] with bi-coordination sites of N and O were employed as perovskite surface defect passivants to address the efficiency and stability issues of perovskite solar cells (PSCs), with typical phenethylammonium iodide (PEAI) and piperazinium iodide (PI) passivants as reference. The surface properties of the perovskite films before and after passivation were characterized by Fourier-transform infrared, ultraviolet-visible, photoluminescence (PL), and time-resolved PL spectroscopy, X-ray diffraction, ultraviolet photoelectron spectroscopy, scanning electron microscopy, and atomic force microscopy. The characterizations reveal that BPY, DQCN, or TTFA forms coordination bonds with exposed "Pb²⁺", leading to a slight decrease in the highest occupied molecular orbital or lowest unoccupied molecular orbital energy level and bandgap. These passivants (especially TTFA) can passivate the perovskite surface defects to inhibit non-radiative recombination while having almost no influence on the grain size and surface morphology. Utilizing the passivated perovskite as the light absorption layer, solar cells with an inverted configuration of indium tin oxide/NiO _x /passivated MAPbCl _x I_3-x /C₆₀/BCP/Ag have been fabricated, and power conversion efficiencies of 19.22, 17.85, 16.49, 16.31, and 17.88% have been achieved from PEAI, PI, BPY, DQCN, and TTFA, respectively. All the device performance based on passivated perovskite is superior to that of the control (15.75%) owing to the reduced carrier recombination. The device from TTFA exhibits almost comparable efficiency to that of PEAI and PI controls, indicating that TTFA has an equal excellent passivation effect to state-of-the-art PEAI and PI. Furthermore, the devices based on BPY, DQCN, and TTFA show superior long-term stability with an efficiency loss of only 13.2, 16.7, and 12.9%, respectively, after being stored for 40 days in a ∼12% humidity, low-oxygen level environment, which is 45.4, 38.8, and 44.4% for the control, PEAI, and PI devices, respectively, primarily due to the improved hydrophobicity of the perovskite surface. Our results demonstrate that it is feasible to achieve high-efficiency and long-term-stable perovskite solar cells via selecting the appropriate molecules to passivate perovskite surface defects.

Developments on Perovskite Solar Cells (PSCs): A Critical Review

This review provides detailed information on perovskite solar cell device background and monitors stepwise scientific efforts applied to improve device performance with time. The work reviews previous studies and the latest developments in the perovskite crystal structure, electronic structure, device architecture, fabrication methods, and challenges. Advantages, such as easy bandgap tunability, low charge recombination rates, and low fabrication cost, are among the topics discussed. Some of the most important elements highlighted in this review are concerns regarding commercialization and prototyping. Perovskite solar cells are generally still lab-based devices suffering from drawbacks such as device intrinsic and extrinsic instabilities and rising environmental concerns due to the use of the toxic inorganic lead (Pb) element in the perovskite (ABX3) light-active material. Some interesting recommendations and possible future perspectives are well articulated.

Electrochemically induced iodine migration in mixed halide perovskites: suppression through chloride insertion

The role of chloride in improving the stability of mixed halide perovskites (MAPbCl_xBr_0.5(1-x)I_0.5(1-x))₃ is probed using spectroelectrochemistry. The injection of holes into mixed halide perovskite films through applied anodic bias results in the selective migration of iodine with ultimate expulsion into the electrolyte. Increasing the Cl content (x = 0 to 0.1) in the mixed halide perovskite suppresses the iodine mobility and thus decreases the rate of its expulsion into the solution. Implications of iodine mobility induced by hole accumulation and its impact on overall stability is discussed.

Photocorrosion at Irradiated Perovskite/Electrolyte Interfaces

Metal-halide perovskites transformed optoelectronics research and development during the past decade. They have also gained a foothold in photocatalytic and photoelectrochemical processes recently, but their sensitivity to the most commonly applied solvents and electrolytes together with their susceptibility to photocorrosion hinders such applications. Understanding the elementary steps of photocorrosion of these materials can aid the endeavor of realizing stable devices. In this Perspective, we discuss both thermodynamic and kinetic aspects of photocorrosion processes occurring at the interface of perovskite photocatalysts and photoelectrodes with different electrolytes. We show how combined in situ and operando electrochemical techniques can reveal the underlying mechanisms. Finally, we also discuss emerging strategies to mitigate photocorrosion (such as surface protection, materials and electrolyte engineering, etc.).