Silicon Nitride: A Bioceramic with a Gift

Biological Activity of Silicon Nitride Ceramics: A Critical Review

The commercial use of Si3N4 ceramics in the biomedical field dates back to the early 1980s and, initially, did not show promising results, which is why their biocompatibility was not then investigated further until about 10 years later. Over the years, a change in trend has been observed; more and more studies have shown that this material could possess high biocompatibility and antibacterial properties. However, the relevant literature struggles to find mechanisms that can incontrovertibly explain the reasons behind the biological activity of Si3N4. The proposed mechanisms are often pure hypotheses or are not substantiated by comprehensive analyses. This review begins by studying the early references to the biological activity of Si3N4 and then reviews the literature regarding the bioactivity of this ceramic over time. An examination of the early insights into surface chemistry and biocompatibility lays the foundation for a detailed examination of the chemical reactions that Si3N4 undergoes in biological environments. Next, the analysis focuses on the mechanisms of bioactivity and antipathogenicity that the material exhibits both alone and in combination with modern bioglass. However, it is highlighted that despite the general consensus on the biocompatibility and bioactivity of Si3N4 ceramics, sometimes the proposed biological mechanisms behind its behavior are discordant or unsupported by the direct evaluation of specific biochemical activities. This review highlights both the reliable information in the literature and the gaps in research that need to be filled in order to fully understand the reasons behind the biological properties of this material.

Gas Therapy: Generating, Delivery, and Biomedical Applications

Oxygen (O2), nitric oxide (NO), carbon monoxide (CO), hydrogen sulfide (H2S), and hydrogen (H2) with direct effects, and carbon dioxide (CO2) with complementary effects on the condition of various diseases are known as therapeutic gases. The targeted delivery and in situ generation of these therapeutic gases with controllable release at the site of disease has attracted attention to avoid the risk of gas poisoning and improve their performance in treating various diseases such as cancer therapy, cardiovascular therapy, bone tissue engineering, and wound healing. Stimuli-responsive gas-generating sources and delivery systems based on biomaterials that enable on-demand and controllable release are promising approaches for precise gas therapy. This work highlights current advances in the design and development of new approaches and systems to generate and deliver therapeutic gases at the site of disease with on-demand release behavior. The performance of the delivered gases in various biomedical applications is then discussed.

Fabrication and characterization of sodium alginate-silicon nitride-PVA composite biomaterials with damping properties

Silicon nitride is utilized clinically as a bioceramic for spinal fusion cages, owing to its high strength, osteoconductivity, and antibacterial effects. Nevertheless, silicon nitride exhibits suboptimal damping properties, a critical factor in mitigating traumatic bone injuries and fractures. In fact, there is a scarcity of spinal implants that simultaneously demonstrate proficient damping performance and support osteogenesis. In our study, we fabricated a novel sodium alginate-silicon nitride/poly(vinyl alcohol) (SA-SiN/PVA) composite scaffold, enabling enhanced energy absorption and rapid elastic recovery under quasi-static and impact loading scenarios. Furthermore, the study demonstrated that the incorporation of physical and chemical cross-linking significantly improved stiffness and recoverable energy dissipation. Concerning the interaction between cells and materials, our findings suggest that the addition of silicon nitride stimulated osteogenic differentiation while inhibiting Staphylococcus aureus growth. Collectively, the amalgamation of ceramics and tough hydrogels facilitates the development of advanced composites for spinal implants, manifesting superior damping, osteogenic potential, and antibacterial properties. This approach holds broader implications for applications in bone tissue engineering.

Effects of sintering additives and sintering methods on the mechanical, antimicrobial and optical properties of Si3N4 bioceramics

Si3N4 bioceramics were fabricated using GPS and SPS method with MgO-RE2O3 (RE = La, Nd, Gd, Ho and Lu) sintering additives. The effect of sintering methods and sintering additives on the grain growth, mechanical, antimicrobial properties and color of Si3N4 bioceramics were studied. Samples sintered with GPS are composed of β-Si3N4 and samples sintered with SPS are composed of α-Si3N4 and β-Si3N4. The growth of β-Si3N4 grains in samples sintered with GPS are more adequate. Samples sintered with GPS exhibit a S. aureus inactivation rate up to 98% and a bright color appearance with a hardness of about 13 GPa and a fracture toughness up to 7.5 MPa m1/2, suitable for dental implants. And samples sintered with SPS exhibit a hardness of about 17 GPa and a fracture toughness about 6 MPa m1/2.

Silicon Nitride Bioceramics Sintered by Microwave Exhibit Excellent Mechanical Properties, Cytocompatibility In Vitro, and Anti-Bacterial Properties

Silicon nitride is a bioceramic with great potential, and multiple studies have demonstrated its biocompatibility and antibacterial properties. In this study, silicon nitride was prepared by a microwave sintering technique that was different from common production methods. SEM and pore distribution analysis revealed the microstructure of microwave-sintered silicon nitride with obvious pores. Mechanical performance analysis shows that microwave sintering can improve the mechanical properties of silicon nitride. The CCK-8 method was used to demonstrate that microwave-sintered silicon nitride has no cytotoxicity and good cytocompatibility. From SEM and CLSM observations, it was observed that there was good adhesion and cross-linking of cells during microwave-sintered silicon nitride, and the morphology of the cytoskeleton was good. Microwave-sintered silicon nitride has been proven to be non-cytotoxic. In addition, the antibacterial ability of microwave-sintered silicon nitride against Staphylococcus aureus and Escherichia coli was tested, proving that it has a good antibacterial ability similar to the silicon nitride prepared by commonly used processes. Compared with silicon nitride prepared by gas pressure sintering technology, microwave-sintered silicon nitride has excellent performance in mechanical properties, cell compatibility, and antibacterial properties. This indicates its enormous potential as a substitute material for manufacturing bone implants.

Recent advances in the application and biological mechanism of silicon nitride osteogenic properties: a review

Silicon nitride, an emerging bioceramic material, is highly sought after in the biomedical industry due to its osteogenesis-promoting properties, which are a result of its unique surface chemistry and excellent mechanical properties. Currently, it is used in clinics as an orthopedic implant material. The osteogenesis-promoting properties of silicon nitride are manifested in its contribution to the formation of a local osteogenic microenvironment, wherein silicon nitride and its hydrolysis products influence osteogenesis by modulating the biological behaviors of the constituents of the osteogenic microenvironment. In particular, silicon nitride regulates redox signaling, cellular autophagy, glycolysis, and bone mineralization in cells involved in bone formation via several mechanisms. Moreover, it may also promote osteogenesis by influencing immune regulation and angiogenesis. In addition, the wettability, surface morphology, and charge of silicon nitride play crucial roles in regulating its osteogenesis-promoting properties. However, as a bioceramic material, the molding process of silicon nitride needs to be optimized, and its osteogenic mechanism must be further investigated. Herein, we summarize the impact of the molding process of silicon nitride on its osteogenic properties and clinical applications. In addition, the mechanisms of silicon nitride in promoting osteogenesis are discussed, followed by a summary of the current gaps in silicon nitride mechanism research. This review, therefore, aims to provide novel ideas for the future development and applications of silicon nitride.

3D-Printed PEEK/Silicon Nitride Scaffolds with a Triply Periodic Minimal Surface Structure for Spinal Fusion Implants

The issue of spine-related disorders is a global healthcare concern that requires effective solutions to restore normal spine functioning. Spinal fusion implants have become a standard approach for this purpose, making it crucial to develop biomaterials and structures that possess high osteogenic capacities and exhibit mechanical properties and dynamic responses similar to those of the host bone. This study focused on the fabrication of 3D-printed polyether ether ketone/silicon nitride (PEEK/SiN) scaffolds with a triply periodic minimal surface (TPMS) structure, which offers several advantages, such as a large surface area and uniform stress distribution under load. The mechanical properties and dynamic response of PEEK/SiN scaffolds with varying porosities were evaluated through mechanical testing and finite element analysis. The scaffold with 30% porosity exhibited a compressive strength (34.56 ± 1.91 MPa) and elastic modulus (734 ± 64 MPa) similar to those of trabecular bone. In addition, the scaffold demonstrated favorable damping properties. The biological data revealed that incorporating silicon nitride into the PEEK scaffold stimulated osteogenic differentiation. In light of these findings, it can be inferred that PEEK/SiN TPMS scaffolds exhibit significant potential for use in bone tissue engineering and represent a promising option as candidates for spinal fusion implants.

Instantaneous Inactivation of Herpes Simplex Virus by Silicon Nitride Bioceramics

Hydrolytic reactions taking place at the surface of a silicon nitride (Si3N4) bioceramic were found to induce instantaneous inactivation of Human herpesvirus 1 (HHV-1, also known as Herpes simplex virus 1 or HSV-1). Si3N4 is a non-oxide ceramic compound with strong antibacterial and antiviral properties that has been proven safe for human cells. HSV-1 is a double-stranded DNA virus that infects a variety of host tissues through a lytic and latent cycle. Real-time reverse transcription (RT)-polymerase chain reaction (PCR) tests of HSV-1 DNA after instantaneous contact with Si3N4 showed that ammonia and its nitrogen radical byproducts, produced upon Si3N4 hydrolysis, directly reacted with viral proteins and fragmented the virus DNA, irreversibly damaging its structure. A comparison carried out upon testing HSV-1 against ZrO2 particles under identical experimental conditions showed a significantly weaker (but not null) antiviral effect, which was attributed to oxygen radical influence. The results of this study extend the effectiveness of Si3N4's antiviral properties beyond their previously proven efficacy against a large variety of single-stranded enveloped and non-enveloped RNA viruses. Possible applications include the development of antiviral creams or gels and oral rinses to exploit an extremely efficient, localized, and instantaneous viral reduction by means of a safe and more effective alternative to conventional antiviral creams. Upon incorporating a minor fraction of micrometric Si3N4 particles into polymeric matrices, antiherpetic devices could be fabricated, which would effectively impede viral reactivation and enable high local effectiveness for extended periods of time.

The Clinical Use of Osteobiologic and Metallic Biomaterials in Orthopedic Surgery: The Present and the Future

As the area and range of surgical treatments in the orthopedic field have expanded, the development of biomaterials used for these treatments has also advanced. Biomaterials have osteobiologic properties, including osteogenicity, osteoconduction, and osteoinduction. Natural polymers, synthetic polymers, ceramics, and allograft-based substitutes can all be classified as biomaterials. Metallic implants are first-generation biomaterials that continue to be used and are constantly evolving. Metallic implants can be made from pure metals, such as cobalt, nickel, iron, or titanium, or from alloys, such as stainless steel, cobalt-based alloys, or titanium-based alloys. This review describes the fundamental characteristics of metals and biomaterials used in the orthopedic field and new developments in nanotechnology and 3D-printing technology. This overview discusses the biomaterials that clinicians commonly use. A complementary relationship between doctors and biomaterial scientists is likely to be necessary in the future.

A biocompatible silicon nitride dental implant material prepared by digital light processing technology

For decades, titanium has been the preferred material for dental implant fabrication. However, metallic ions and particles can cause hypersensitivity and aseptic loosening. The growing demand for metal-free dental restorations has also promoted the development of ceramic-based dental implants, such as silicon nitride. In this study, silicon nitride (Si₃N₄) dental implants were fabricated for biological engineering by photosensitive resin based digital light processing (DLP) technology, comparable to conventionally produced Si₃N₄ ceramics. The flexural strength was (770 ± 35) MPa by the three-point bending method, and the fracture toughness was (13.3 ± 1.1) MPa · m^1/2 by the unilateral pre-cracked beam method. The elastic modulus measured by the bending method was (236 ± 10) GPa. To confirm whether the prepared Si₃N₄ ceramics possessed good biocompatibility, in vitro biological experiments were performed with the fibroblast cell line L-929, and preferable cell proliferation and apoptosis were observed at the initial stages. Hemolysis test, oral mucous membrane irritation test, and acute systemic toxicity test (oral route) further confirmed that the Si₃N₄ ceramics did not exhibit hemolysis reaction, oral mucosal stimulation, or systemic toxicity. The findings indicate that Si₃N₄ dental implant restorations with personalized structures prepared by DLP technology have good mechanical properties and biocompatibility, which has great application potential in the future.

Raman Fingerprints of the SARS-CoV-2 Delta Variant and Mechanisms of Its Instantaneous Inactivation by Silicon Nitride Bioceramics

Raman spectroscopy uncovered molecular scale markers of the viral structure of the SARS-CoV-2 Delta variant and related viral inactivation mechanisms at the biological interface with silicon nitride (Si3N4) bioceramics. A comparison of Raman spectra collected on the TY11-927 variant (lineage B.1.617.2; simply referred to as the Delta variant henceforth) with those of the JPN/TY/WK-521 variant (lineage B.1.617.1; referred to as the Kappa variant or simply as the Japanese isolate henceforth) revealed the occurrence of key mutations of the spike receptor together with profound structural differences in the molecular structure/symmetry of sulfur-containing amino acid and altered hydrophobic interactions of the tyrosine residue. Additionally, different vibrational fractions of RNA purines and pyrimidines and dissimilar protein secondary structures were also recorded. Despite mutations, hydrolytic reactions at the surface of silicon nitride (Si3N4) bioceramics induced instantaneous inactivation of the Delta variant at the same rate as that of the Kappa variant. Contact between virions and micrometric Si3N4 particles yielded post-translational deimination of arginine spike residues, methionine sulfoxidation, tyrosine nitration, and oxidation of RNA purines to form formamidopyrimidines. Si3N4 bioceramics proved to be a safe and effective inorganic compound for instantaneous environmental sanitation.

A Novel Antipathogenic Agent for Nonwoven Fabric

Medical-grade masks and N95 respirators containing non-woven fibers are designed to prevent the spread of airborne diseases. While they effectively trap respiratory droplets and aerosols, they cannot lyse entrapped pathogens. Embedded antimicrobial agents such as silver, copper, zinc, iodine, peptides, quaternary ammonium salts, or nanoparticles have been used to overcome this limitation. However, their effectiveness remains debatable because these materials can be toxins, allergens, irritants, and environmental hazards. Recently, silicon nitride (Si3N4) was found to be a potent antipathogenic compound, and it may be an ideal agent for masks. In powder or solid form, it is highly effective in inactivating bacteria, fungi, and viruses while leaving mammalian tissue unaffected. The purpose of this study was to serially assess the antiviral efficacy of Si3N4 against SARS-CoV-2 using powders, solids, and embedded nonwoven fabrics. Si3N4 powders and solids were prepared using conventional ceramic processing. The “pad-dry-cure” method was used to embed Si3N4 particles into polypropylene fibers. Fabric testing was subsequently conducted using industrial standards—ISO 18184 for antiviral effectiveness, ASTM F2299 and EN 13274-7 for filtration efficiency, EN 14683 for differential pressure drop, and ISO 18562-2 for particle shedding. A modification of ISO 18562-3 was also employed to detect ammonia release from the fabric. Antiviral effectiveness for Si3N4 powders, solids, and embedded fabrics were 99.99% at ≤ 5 min, ~ 93% in 24 h, and 87% to 92% in 120 min, respectively. Results of the standard mask tests were generally within prescribed safety limits. Further process optimization may lead to commercial Si3N4-based masks that not only “catch” but also “kill” pathogenic microbes.

Silicon Nitride as a Biomedical Material: An Overview

Silicon nitride possesses a variety of excellent properties that can be specifically designed and manufactured for different medical applications. On the one hand, silicon nitride is known to have good mechanical properties, such as high strength and fracture toughness. On the other hand, the uniqueness of the osteogenic/antibacterial dualism of silicon nitride makes it a favorable bioceramic for implants. The surface of silicon nitride can simultaneously inhibit the proliferation of bacteria while supporting the physiological activities of eukaryotic cells and promoting the healing of bone tissue. There are hardly any biomaterials that possess all these properties concurrently. Although silicon nitride has been intensively studied as a biomedical material for years, there is a paucity of comprehensive data on its properties and medical applications. To provide a comprehensive understanding of this potential cornerstone material of the medical field, this review presents scientific and technical data on silicon nitride, including its mechanical properties, osteogenic behavior, and antibacterial capabilities. In addition, this paper highlights the current and potential medical use of silicon nitride and explains the bottlenecks that need to be addressed, as well as possible solutions.

Tailoring the dissolution rate and in vitro cell response of silicon nitride coatings through combinatorial sputtering with chromium and niobium

Ceramic coatings have been widely investigated as a means to reduce wear and metallic ion release from joint implants. Silicon nitride-based coatings have been a topic of interest specifically due to their solubility in aqueous solutions. This could imply a reduced adverse immune response since the generated debris would dissolve. However, there are concerns regarding the dissolution rate and adhesion of these silicon nitride-based coatings. This study attempts to address the concern of dissolution rate as well as coating adhesion of silicon nitride coatings. We hypothesized that alloying with chromium and niobium would affect the adhesion, dissolution rate, and the resulting ion release and cell response to the coatings. A combinatorial approach was used to deposit sputtered coatings with compositional gradients both with and without a CrN interlayer. Compositional gradients were achieved for all the investigated elements: Si (38.6-46.9 at%), Nb (2.2-4.6 at%) and Cr (1.9-6.0 at%). However, while the presence of an interlayer reduced the delamination during adhesion testing, the differences in composition in the top coating did not affect the adhesion. Nor did the top coating's composition affect the surface roughness or the coatings' inherent mechanical properties (elastic modulus and hardness). All coating compositions were associated with a low Co release from the underlying metal and points with a higher Cr content (4.3-6.0 at%) gave an overall lower release of Si, Cr and Nb ions, possibly due to the formation of a stable oxide, which reduced the dissolution rate of the coating. Optimum chromium contents were furthermore found to give an enhanced in vitro fibroblast cell viability. In conclusion, the results indicate a possibility to tailor the ion release rate, which lends promise to further investigations such as tribocorrosive tests towards a future biomedical application.

Nitric Oxide Delivering Surfaces: An Overview of Functionalization Strategies and Efficiency Progress

An overview on the design of nitric oxide (NO) delivering surfaces for biomedical purposes is provided, with a focus on the advances of the past 5 years. A localized supply of NO is of a particular interest due to the pleiotropic biological effects of this diatomic compound. Depending on the generated NO flux, the surface can mimic a physiological release profile to provide an activity on the vascular endothelium or an antibacterial activity. Three requirements are considered to describe the various strategies leading to a surface delivering NO. Firstly, the coating must be selected in accordance with the properties of the substrate (nature, shape, dimensions…). Secondly, the releasing and/or generating kinetics of NO should match the targeted biological application. Currently, the most promising structures are developed to provide an adaptable NO supply driven by pathophysiological needs. Finally, the biocompatibility and the stability of the surface must also be considered regarding the expected residence time of the device. A critical point of view is proposed to help readers in the design of the NO delivering surface according to its expected requirement and therapeutic purpose.

Ceramic Toughening Strategies for Biomedical Applications

Aiming at shortage of metal materials, ceramic is increasingly applied in biomedicine due to its high strength, pleasing esthetics and good biocompatibility, especially for dental restorations and implants, artificial joints, as well as synthetic bone substitutes. However, the inherent brittleness of ceramic could lead to serious complications, such as fracture and disfunction of biomedical devices, which impede their clinical applications. Herein, several toughening strategies have been summarized in this review, including reinforcing phase addition, surface modification, and manufacturing processes improvement. Doping metal and/or non-metal reinforcing fillers modifies toughness of bulk ceramic, while surface modifications, mainly coating, chemical and thermal methods, regulate toughness on the surface layer. During fabrication, optimization should be practiced in powder preparation, green forming and densification processes. Various toughening strategies utilize mechanisms involving fine-grained, stress-induced phase transformation, and microcrack toughening, as well as crack deflection, bifurcation, bridging and pull-out. This review hopes to shed light on systematic combination of different toughening strategies and mechanisms to drive progress in biomedical devices.

Improved sintering performance of β-SiAlON-Si3N4 and its osteogenic differentiation ability by adding β-SiAlON

To improve the sintering performance of silicon nitride bioceramics, we explored the effect of β-SiAlON's Z-value on the physical, chemical, and biological properties of β-SiAlON-Si₃N₄ composites. Results showed that the phase product was β-Si₃N₄. As the Z-value increased, the X-ray diffraction peaks gradually shifted to a smaller angle, the material grains were more tightly packed, and the bulk density and compressive strength increased, reaching the highest values (2.71 g/cm³ and 1157 MPa, respectively) at Z = 4. Soaking and ion-release experiments show that in an aqueous environment, a small amount of Al and Si ions were released, and no obvious decomposition occurred on the surface of the material. The biological performance showed that the growth of cultured cells in each group was in good condition, there was no obvious difference in morphology and adhesion, and the materials had good biological performance. An increase in the Z-value promotes the formation of mineralized nodules and osteogenic differentiation of MC3T3-E1 cells, which may be because the release of Si can promote osteogenic differentiation. Therefore, the addition of β-SiAlON could improve the sintering performance of β-Si₃N₄ without degrading its biological properties. The prepared β-SiAlON-Si₃N₄ composite ceramic is a latent bioceramic material.

Comparison of surface properties, cell behaviors, bone regeneration and osseointegration between nano tantalum/PEEK composite and nano silicon nitride/PEEK composite

Both tantalum (Ta) and silicon nitride (SN) exhibit osteogenic bioactivity and antibacterial property. In addition, as a biomaterial for bone repair, polyetheretherketone (PEEK) has outstanding biocompatibility and mechanical performances while it is biologically inert. In this study, by blending PEEK with Ta and SN nanoparticles, respectively, Ta/PEEK composite (TPC) and SN/PEEK composite (SPC) were fabricated for load-bearing bone repair. The surface roughness, hydrophilicity and surface energy of TPC containing Ta nanoparticles were higher than SPC containing SN nanoparticles and PEEK. In addition, TPC with Ta nanoparticles exhibited low antibacterial property while SPC with SN nanoparticles showed high bacterial property. Moreover, the MC3T3-E1 cells responses (e.g. proliferation and differentiation) to TPC was the highest while PEEK was the lowest in vitro. Furthermore, new bone formation and osseointegration for TPC was the highest while PEEK was the lowest in vivo. In conclusion, compared with PEEK, addition of Ta and SN nanoparticles into PEEK fabricated bioactive composites of TPC and SPC with optimized surface property, which played crucial roles in inducing cellular response/bone regeneration. Although the osteogenic activity of SPC was lower than TPC, SPC exhibited osteogenic activity and good antibacterial property, which could prevent infection from bacterial. Therefore, SPC would have better potential for bone substitute.

Silicon Nitride, a Bioceramic for Bone Tissue Engineering: A Reinforced Cryogel System With Antibiofilm and Osteogenic Effects

Silicon nitride (SiN [Si3N4]) is a promising bioceramic for use in a wide variety of orthopedic applications. Over the past decades, it has been mainly used in industrial applications, such as space shuttle engines, but not in the medical field due to scarce data on the biological effects of SiN. More recently, it has been increasingly identified as an emerging material for dental and orthopedic implant applications. Although a few reports about the antibacterial properties and osteoconductivity of SiN have been published to date, there have been limited studies of SiN-based scaffolds for bone tissue engineering. Here, we developed a silicon nitride reinforced gelatin/chitosan cryogel system (SiN-GC) by loading silicon nitride microparticles into a gelatin/chitosan cryogel (GC), with the aim of producing a biomimetic scaffold with antibiofilm and osteogenic properties. In this scaffold system, the GC component provides a hydrophilic and macroporous environment for cells, while the SiN component not only provides antibacterial properties and osteoconductivity but also increases the mechanical stiffness of the scaffold. This provides enhanced mechanical support for the defect area and a better osteogenic environment. First, we analyzed the scaffold characteristics of SiN-GC with different SiN concentrations, followed by evaluation of its apatite-forming capacity in simulated body fluid and protein adsorption capacity. We further confirmed an antibiofilm effect of SiN-GC against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) as well as enhanced cell proliferation, mineralization, and osteogenic gene upregulation for MC3T3-E1 pre-osteoblast cells. Finally, we developed a bioreactor to culture cell-laden scaffolds under cyclic compressive loading to mimic physiological conditions and were able to demonstrate improved mineralization and osteogenesis from SiN-GC. Overall, we confirmed the antibiofilm and osteogenic effect of a silicon nitride reinforced cryogel system, and the results indicate that silicon nitride as a biomaterial system component has a promising potential to be developed further for bone tissue engineering applications.

Tailoring Silicon Nitride Surface Chemistry for Facilitating Odontogenic Differentiation of Rat Dental Pulp Cells

Silicon nitride (Si3N4) can facilitate bone formation; hence, it is used as a biomaterial in orthopedics. Nevertheless, its usability for dentistry is unexplored. The aim of the present study was to investigate the effect of Si3N4 granules for the proliferation and odontogenic differentiation of rat dental pulp cells (rDPCs). Four different types of Si3N4 granules were prepared, which underwent different treatments to form pristine as-synthesized Si3N4, chemically treated Si3N4, thermally treated Si3N4, and Si3N4 sintered with 3 wt.% yttrium oxide (Y2O3). rDPCs were cultured on or around the Si3N4 granular beds. Compared with the other three types of Si3N4 granules, the sintered Si3N4 granules significantly promoted cellular attachment, upregulated the expression of odontogenic marker genes (Dentin Matrix Acidic Phosphoprotein 1 and Dentin Sialophosphoprotein) in the early phase, and enhanced the formation of mineralization nodules. Furthermore, the water contact angle of sintered Si3N4 was also greatly increased to 40°. These results suggest that the sintering process for Si3N4 with Y2O3 positively altered the surface properties of pristine as-synthesized Si3N4 granules, thereby facilitating the odontogenic differentiation of rDPCs. Thus, the introduction of a sintering treatment for Si3N4 granules is likely to facilitate their use in the clinical application of dentistry.

Mechanisms of instantaneous inactivation of SARS-CoV-2 by silicon nitride bioceramic

The hydrolytic processes occurring at the surface of silicon nitride (Si3N4) bioceramic have been indicated as a powerful pathway to instantaneous inactivation of SARS-CoV-2 virus. However, the virus inactivation mechanisms promoted by Si3N4 remain yet to be elucidated. In this study, we provide evidence of the instantaneous damage incurred on the SARS-CoV-2 virus upon contact with Si3N4. We also emphasize the safety characteristics of Si3N4 for mammalian cells. Contact between the virions and micrometric Si3N4 particles immediately targeted a variety of viral molecules by inducing post-translational oxidative modifications of S-containing amino acids, nitration of the tyrosine residue in the spike receptor binding domain, and oxidation of RNA purines to form formamidopyrimidine. This structural damage in turn led to a reshuffling of the protein secondary structure. These clear fingerprints of viral structure modifications were linked to inhibition of viral functionality and infectivity. This study validates the notion that Si3N4 bioceramic is a safe and effective antiviral compound; and a primary antiviral candidate to replace the toxic and allergenic compounds presently used in contact with the human body and in long-term environmental sanitation.

Comprehensive in vitro comparison of cellular and osteogenic response to alternative biomaterials for spinal implants

A variety of novel biomaterials are emerging as alternatives to conventional metals and alloys, for use in spinal implants. These promise potential advantages with respect to e.g. elastic modulus compatibility with the host bone, improved radiological imaging or enhanced cellular response to facilitate osseointegration. However, to date there is scarce comparative data on the biological response to many of these biomaterials that would give insights into the relative level of bone formation, resorption inhibition and inflammation. Thus, in this study, we aimed to evaluate and compare the in vitro biological response to standard discs of four alternative biomaterials: polyether ether ketone (PEEK), zirconia toughened alumina (ZTA), silicon nitride (SN) and surface-textured silicon nitride (ST-SN), and the reference titanium alloy Ti6Al4V (TI). Material-specific characteristics of these biomaterials were evaluated, such as surface roughness, wettability, protein adsorption (BSA) and apatite forming capacity in simulated body fluid. The activity of pre-osteoblasts seeded on the discs was characterized, by measuring viability, proliferation, attachment and morphology. Then, the osteogenic differentiation of pre-osteoblasts was compared in vitro from early to late stage by Alizarin Red S staining and real-time PCR analysis. Finally, osteoclast activity and inflammatory response were assessed by real-time PCR analysis. Compared to TI, all other materials generally demonstrated a lower osteoclastic activity and inflammatory response. ZTA and SN showed generally an enhanced osteogenic differentiation and actin length. Overall, we could show that SN and ST-SN showed a higher osteogenic effect than the other reference groups, an inhibitive effect against bone resorption and low inflammation, and the results indicate that silicon nitride has a promising potential to be developed further for spinal implants that require enhanced osseointegration.

Enhanced biomaterials: systematic review of alternatives to supplement spine fusion including silicon nitride, bioactive glass, amino peptide bone graft, and tantalum

OBJECTIVE

Spinal fusions are among the most common and effective spinal surgical practices; however, the current model presents some cost and safety concerns within the patient population. Therefore, enhanced biomaterials have been presented to be an innovative yet underutilized tool to supplement the success of spinal fusion surgery. Herein, the authors discuss these biomaterials, their compositions, clinical outcomes, and cost analysis through a systematic review of the literature to date.

METHODS

This systematic review was conducted using the PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) criteria and guidelines. Article selection was performed using the PubMed electronic bibliographic databases. The search yielded 1168 articles that were assessed and filtered for relevance by the four authors. Following the screening of titles and abstracts, 62 articles were deemed significant enough for final selection.

RESULTS

To date, silicon nitride, bioactive glass, amino peptide bone grafts, and tantalum are all biomaterials that could have significant roles in supporting spinal fusion. Their unique compositions allow them to be biocompatible in the spine, and their mechanisms of action stimulate osteoblast formation and support fusion success. Moreover, these biomaterials also present positive clinical and cost outcomes that support their application in spinal procedures. However, further studies with longer follow-ups are necessary to fully understand these biomaterials prior to their incorporation in mainstream spinal practice.

CONCLUSIONS

The combination of their positive clinical outcomes, biocompatibility, and cost-effectiveness makes these biomaterials valuable, innovative, and effective treatment modalities that could revolutionize the current model of spinal fusion.

Nanoparticles for the Treatment of Inner Ear Infections

The inner ear is sensitive to various infections of viral, bacterial, or fungal origin, which, if left untreated, may lead to hearing loss or progress through the temporal bone and cause intracranial infectious complications. Due to its isolated location, the inner ear is difficult to treat, imposing an acute need for improving current therapeutic approaches. A solution for enhancing antimicrobial treatment performance is the use of nanoparticles. Different inorganic, lipidic, and polymeric-based such particles have been designed, tested, and proven successful in the controlled delivery of medication, improving drug internalization by the targeted cells while reducing the systemic side effects. This paper makes a general presentation of common inner ear infections and therapeutics administration routes, further focusing on newly developed nanoparticle-mediated treatments.

Antifungal activity of polymethyl methacrylate/Si3N4 composites against Candida albicans

Previous studies using gram-positive and -negative bacteria demonstrated that hydrolysis of silicon nitride (Si₃N₄) in aqueous suspensions elutes nitrogen and produces gaseous ammonia while buffering pH. According to immunochemistry assays, fluorescence imaging, and in situ Raman spectroscopy, we demonstrate here that the antipathogenic surface chemistry of Si₃N₄ can be extended to polymethylmethacrylate (PMMA) by compounding it with a minor fraction (~8 vol.%) of Si₃N₄ particles without any tangible loss in bulk properties. The hydrolytic products, which were eluted from partly exposed Si₃N₄ particles at the composite surface, exhibited fungicidal action against Candida albicans. Using a specific nitrative stress sensing dye and highly resolved fluorescence micrographs, we observed in situ congestion of peroxynitrite (ONOO^-) radicals in the mitochondria of the Candida cells exposed to the PMMA/Si₃N₄ composite, while these radicals were absent in the mitochondria of identical cells exposed to monolithic PMMA. These in situ observations suggest that the surface chemistry of Si₃N₄ mimics the antifungal activity of macrophages, which concurrently produce NO radicals and superoxide anions (O₂•^-) resulting in the formation of candidacidal ONOO^-. The fungicidal properties of PMMA/Si₃N₄ composites could be used in dental appliances to inhibit the uncontrolled growth of Candida albicans and ensuing candidiasis while being synergic with chemoprophylaxis. STATEMENT OF SIGNIFICANCE: In a follow-up of previous studies of gram-positive and gram-negative bacteria, we demonstrate here that the antipathogenic surface chemistry of Si₃N₄ could be extended to polymethylmethacrylate (PMMA) containing a minor fraction (~8 vol.%) of Si₃N₄ particles without tangible loss in bulk properties. Hydrolytic products eluted from Si₃N₄ particles at the composite surface exhibited fungicidal action against Candida albicans. Highly resolved fluorescence microscopy revealed congestion of peroxynitrite (ONOO^-) radicals in the mitochondria of the Candida cells exposed to the PMMA/Si₃N₄ composite, while radicals were absent in the mitochondria of identical cells exposed to monolithic PMMA. The fungicidal properties of PMMA/Si₃N₄ composites could be used in dental appliances to inhibit uncontrolled growth of Candida albicans and ensuing candidiasis in synergy with chemoprophylaxis.

Silicon nitride: a potent solid-state bioceramic inactivator of ssRNA viruses

Surface inactivation of human microbial pathogens has a long history. The Smith Papyrus (2600 ~ 2200 B.C.) described the use of copper surfaces to sterilize chest wounds and drinking water. Brass and bronze on doorknobs can discourage microbial spread in hospitals, and metal-base surface coatings are used in hygiene-sensitive environments, both as inactivators and modulators of cellular immunity. A limitation of these approaches is that the reactive oxygen radicals (ROS) generated at metal surfaces also damage human cells by oxidizing their proteins and lipids. Silicon nitride (Si₃N₄) is a non-oxide ceramic compound with known surface bacterial resistance. We show here that off-stoichiometric reactions at Si₃N₄ surfaces are also capable of inactivating different types of single-stranded RNA (ssRNA) viruses independent of whether their structure presents an envelop or not. The antiviral property of Si₃N₄ derives from a hydrolysis reaction at its surface and the subsequent formation of reactive nitrogen species (RNS) in doses that could be metabolized by mammalian cells but are lethal to pathogens. Real-time reverse transcription (RT)-polymerase chain reaction (PCR) tests of viral RNA and in situ Raman spectroscopy suggested that the products of Si₃N₄ hydrolysis directly react with viral proteins and RNA. Si₃N₄ may have a role in controlling human epidemics related to ssRNA mutant viruses.

Activity and Mechanism of Action of the Bioceramic Silicon Nitride as an Environmentally Friendly Alternative for the Control of the Grapevine Downy Mildew Pathogen Plasmopara viticola

Downy mildew of grapevine, caused by Plasmopara viticola (Berk. and Curt.) Berl. and de Toni, is one of the most devastating diseases of grapevine, severely affecting grape and wine production and quality worldwide. Infections are usually controlled by the intensive application of synthetic fungicides or by copper-based products in organic farming, rising problems for soil contamination and adverse impacts on environment and human health. While strict regulations attempt to minimize their harmful consequences, the situation calls for the development of alternative fungicidal strategies. This study presents the unprecedented case of a bioceramic, silicon nitride, with antimicrobial properties against P. viticola, but without adverse effects on human cells and environment, opening the way to the possible extension of silicon nitride applications in agriculture. Raman spectroscopic assessments of treated sporangia in conjunction with microscopic observations mechanistically showed that the nitrogen-chemistry of the bioceramic surface affects pathogen's biochemical components and cell viability, thus presenting a high potential for host protection from P. viticola infections.

Surface functionalization of PEEK with silicon nitride

Surface roughness, bioactivity, and antibacterial properties are desirable in skeletal implants. We hot-pressed a mix of particulate sodium chloride (NaCl) salt and silicon nitride (β-Si3N4) onto the surface of bulk PEEK. NaCl grains were removed by leaching in water, resulting in a porous PEEK surface embedded with ~15 vol.% β-Si3N4 particles. This functionalized surface showed the osteogenic and antibacterial properties previously reported in bulk silicon nitride implants. Surface enhancement of PEEK with β-Si3N4 could improve the performance of spinal fusion cages, by facilitating arthrodesis and resisting bacteria.

Clinical outcomes for lumbar fusion using silicon nitride versus other biomaterials

BACKGROUND

In lumbar fusion surgery, intervertebral spacer cages made of silicon nitride (Si3N4) ceramic are an available option among other biomaterials. While the surface chemistry of Si3N4 is known to favor bone fusion, large-scale clinical studies attesting to its efficacy are lacking. This multicenter retrospective study compared lumbar fusion outcomes for Si3N4 cages to previously reported data for other cage materials.

METHODS

Pre-operative patient demographics, comorbidities, changes in visual analog scale (ΔVAS) pain scores, complications, adverse events, and secondary surgical interventions (SSI) were compiled from the records of 450 patients who underwent Si3N4 lumbar spinal fusion at four separate U.S. surgical centers. For comparison, MEDLINE/PubMed and Google Scholar searches identified studies reporting similar outcomes for other biomaterials. A total of 1,025 patients from 26 cohorts reported in 14 publications met inclusion criteria for this control group.

RESULTS

Overall, the mean last-follow-up for all patients was 341±293 days (11.4±9.8 months), with the longest follow-up being 6.4 years. Patients with Si3N4 implants were similar in gender and age distribution to the control group but had higher BMI values (30.9±6.1 vs. 25.8±4.1, P<0.01) and lower tobacco use (15.8% vs. 30.0%, P<0.01). Both the Si3N4 and control groups showed significant improvements in VAS pain scores from preoperative to last follow-up. For the Si3N4 group, ΔVAS was 36.8±35.4 points compared to 37.6±22.5 points (P=0.63) for the metadata group. Complications and reoperations for the Si3N4 and the control groups were similar (i.e., 9.8% and 3.1% versus 12.4% and 2.9%, P=0.16 and P=0.84, respectively).

CONCLUSIONS

Lumbar fusion with Si3N4 spacers compared favorably with the improvements reported with other commonly used biomaterial cages.

3D-additive deposition of an antibacterial and osteogenic silicon nitride coating on orthopaedic titanium substrate

A 3D-additive manufacturing approach produced a dense Si₃N₄ ceramic coating on a biomedical grade commercially pure titanium (cp-Ti) substrate by an automatic laser-sintering procedure. Si₃N₄ coatings could be prepared with thicknesses from the single to the tens of microns. A coating thickness, t = 15 ± 5 μm, was selected for this study, based on projections of homogeneity and scratching resistance. The Si₃N₄ coating met the 20 N threshold required for biomaterial applications, according to the standard scratch testing (ASTM C1624-05). The Si₃N₄ coating imparted both the antibacterial and osteogenic properties of bulk Si₃N₄ to the cp-Ti substrate. Both properties were comparable to those previously described for bulk Si₃N₄ biomedical implants. The newly developed Si₃N₄-coating was applied to commercially available Ti-alloy acetabular shells for total hip arthroplasty. A "glowing" test based on luciferase gene transformation was applied to visualize the colonization of gram-negative Escherichia coli on Si₃N₄-coated and uncoated Ti-alloy acetabular shells. The results showed that the coating technology conferred resistance to Staphylococcus epidermidis and Escherichia coli adhesion onto the bulk acetabular sockets.

Off-Stoichiometric Reactions at the Cell-Substrate Biomolecular Interface of Biomaterials: In Situ and Ex Situ Monitoring of Cell Proliferation, Differentiation, and Bone Tissue Formation

The availability of osteoinductive biomaterials has encouraged new therapies in bone regeneration and has potentially triggered paradigmatic shifts in the development of new implants in orthopedics and dentistry. Among several available synthetic biomaterials, bioceramics have gained attention for their ability to induce mesenchymal cell differentiation and successive bone formation when implanted in the human body. However, there is currently a lack of understanding regarding the fundamental biochemical mechanisms by which these materials can induce bone formation. Phenomenological studies of retrievals have clarified the final effect of bone formation, but have left the chemical interactions at the cell-material interface uncharted. Accordingly, the knowledge of the intrinsic material properties relevant for osteoblastogenesis and osteoinduction remains incomplete. Here, we systematically monitored in vitro the chemistry of mesenchymal cell metabolism and the ionic exchanges during osteoblastogenesis on selected substrates through conventional biological assays as well as via in situ and ex situ spectroscopic techniques. Accordingly, the chemical behavior of different bioceramic substrates during their interactions with mesenchymal cells could be unfolded and compared with that of biomedical titanium alloy. Our goal was to clarify the cascade of chemical equations behind the biological processes that govern osteoblastogenic effects on different biomaterial substrates.