Nanoheterostructure Construction and DFT Study of Ni-Doped In2O3 Nanocubes/WS2 Hexagon Nanosheets for Formaldehyde Sensing at Room Temperature

Theoretical Study of Dissolved Gas Molecules in Transformer Oil Adsorbed on Intrinsic and TM (Ta, V)-Doped MoTe2 Monolayer

In this paper, CH4, C2H2, H2, and CO adsorbed on intrinsic MoTe2 monolayer and transition metal atom (Ta, V)-doped MoTe2 monolayer have been investigated with density functional theory based on first-principles study. The adsorption energy, geometries, band structures, and density of states of four gases (CH4, C2H2, H2, and CO) adsorbed on the MoTe2 and doped MoTe2 surfaces were analyzed. The results shown that the gas adsorption performance of transition metal atom (Ta, V)-doped MoTe2 monolayers is more superior than that of intrinsic MoTe2, and the adsorption energy and charge transfer of the adsorbed gases on the TM-MoTe2 monolayer are significantly increased in comparison with both sides. Among them, Ta-MoTe2 has the largest Eads value in the adsorbed CO system with a very small adsorption distance, as well as a more suitable recovery time of CO at room temperature, so Ta-MoTe2 can be a candidate material for CO detection. New atoms were introduced during the doping process, which increased the carrier density and carrier mobility of the material, thus improving the charge transfer at the surface of the material. which provides a direction for the gas-sensitive properties of metal Ta-modified MoTe2 materials.

Advances in 2D Materials Based Gas Sensors for Industrial Machine Olfactory Applications

The escalating development and improvement of gas sensing ability in industrial equipment, or "machine olfactory", propels the evolution of gas sensors toward enhanced sensitivity, selectivity, stability, power efficiency, cost-effectiveness, and longevity. Two-dimensional (2D) materials, distinguished by their atomic-thin profile, expansive specific surface area, remarkable mechanical strength, and surface tunability, hold significant potential for addressing the intricate challenges in gas sensing. However, a comprehensive review of 2D materials-based gas sensors for specific industrial applications is absent. This review delves into the recent advances in this field and highlights the potential applications in industrial machine olfaction. The main content encompasses industrial scenario characteristics, fundamental classification, enhancement methods, underlying mechanisms, and diverse gas sensing applications. Additionally, the challenges associated with transitioning 2D material gas sensors from laboratory development to industrialization and commercialization are addressed, and future-looking viewpoints on the evolution of next-generation intelligent gas sensory systems in the industrial sector are prospected.

Solution-Processable and Printable Two-Dimensional Transition Metal Dichalcogenide Inks

Two-dimensional (2D) transition metal dichalcogenides (TMDs) with layered crystal structures have been attracting enormous research interest for their atomic thickness, mechanical flexibility, and excellent electronic/optoelectronic properties for applications in diverse technological areas. Solution-processable 2D TMD inks are promising for large-scale production of functional thin films at an affordable cost, using high-throughput solution-based processing techniques such as printing and roll-to-roll fabrications. This paper provides a comprehensive review of the chemical synthesis of solution-processable and printable 2D TMD ink materials and the subsequent assembly into thin films for diverse applications. We start with the chemical principles and protocols of various synthesis methods for 2D TMD nanosheet crystals in the solution phase. The solution-based techniques for depositing ink materials into solid-state thin films are discussed. Then, we review the applications of these solution-processable thin films in diverse technological areas including electronics, optoelectronics, and others. To conclude, a summary of the key scientific/technical challenges and future research opportunities of solution-processable TMD inks is provided.

Structure-Function Relationship of Highly Reactive CuOx Clusters on Co3 O4 for Selective Formaldehyde Sensing at Low Temperatures

Designing reactive surface clusters at the nanoscale on metal-oxide supports enables selective molecular interactions in low-temperature catalysis and chemical sensing. Yet, finding effective material combinations and identifying the reactive site remains challenging and an obstacle for rational catalyst/sensor design. Here, the low-temperature oxidation of formaldehyde with CuOx clusters on Co3 O4 nanoparticles is demonstrated yielding an excellent sensor for this critical air pollutant. When fabricated by flame-aerosol technology, such CuOx clusters are finely dispersed, while some Cu ions are incorporated into the Co3 O4 lattice enhancing thermal stability. Importantly, infrared spectroscopy of adsorbed CO, near edge X-ray absorption fine structure spectroscopy and temperature-programmed reduction in H2 identified Cu+ and Cu2+ species in these clusters as active sites. Remarkably, the Cu+ surface concentration correlated with the apparent activation energy of formaldehyde oxidation (Spearman's coefficient ρ = 0.89) and sensor response (0.96), rendering it a performance descriptor. At optimal composition, such sensors detected even the lowest formaldehyde levels of 3 parts-per-billion (ppb) at 75°C, superior to state-of-the-art sensors. Also, selectivity to other aldehydes, ketones, alcohols, and inorganic compounds, robustness to humidity and stable performance over 4 weeks are achieved, rendering such sensors promising as gas detectors in health monitoring, air and food quality control.

Real-time, noise and drift resilient formaldehyde sensing at room temperature with aerogel filaments

Formaldehyde, a known human carcinogen, is a common indoor air pollutant. However, its real-time and selective recognition from interfering gases remains challenging, especially for low-power sensors suffering from noise and baseline drift. We report a fully 3D-printed quantum dot/graphene-based aerogel sensor for highly sensitive and real-time recognition of formaldehyde at room temperature. By optimizing the morphology and doping of printed structures, we achieve a record-high and stable response of 15.23% for 1 part per million formaldehyde and an ultralow detection limit of 8.02 parts per billion consuming only ∼130-microwatt power. On the basis of measured dynamic response snapshots, we also develop intelligent computational algorithms for robust and accurate detection in real time despite simulated substantial noise and baseline drift, hitherto unachievable for room temperature sensors. Our framework in combining materials engineering, structural design, and computational algorithm to capture dynamic response offers unprecedented real-time identification capabilities of formaldehyde and other volatile organic compounds at room temperature.

Facile synthesis of Ag lattice doped mesoporous In2O3 nanocubes for high performance ethanol sensing

Ag lattice doped In2O3 with a mesoporous structure was synthesized through a combination of hydrothermal and calcination methods. The structural and morphological characteristics were assessed using XRD, SEM, TEM, TGA, BET, and XPS analyses. Gas sensing measurements revealed that the 7.0 mol% Ag-doped In2O3 sensor displayed a response of 420 towards 100 ppm ethanol at 140 °C, which was 19 times higher than that of the pure In2O3 gas sensor. Density functional theory calculations indicated that Ag-doped In2O3 exhibited enhanced adsorption performance, higher adsorption energy, and electron transfer, resulting in higher sensitivity to ethanol. These findings were also supported by the electronic band structure, work function, and DOS analyses. These results indicated that the Ag doped mesoporous In2O3 has high potential for the preparation of high-performance ethanol sensors in practical applications.

Single Ni Atom-Dispersed WSe2 Monolayer for Sensing Typical Fault Gases in Dry-Type Transformers: A First-Principles Study

This work, using the first-principles theory, uses the Ni-decorated WSe2 (Ni-WSe2) monolayer as a novel gas sensing material upon CO and HCHO in the dry-type transformers in order to evaluate their operation status. Results indicate that the Ni atom can be stably adsorbed on the TW site of the pristine WSe2 monolayer with the binding force of -4.33 eV. Via the gas adsorption analysis, it is found that the Ni-WSe2 monolayer performs chemisorption upon CO and HCHO molecules, with adsorption energies of -2.27 and -1.37 eV, respectively. The analyses of the band structure and Frontier molecular orbital manifest the potential of the Ni-WSe2 monolayer as a resistance-type gas sensor upon CO and HCHO, with sensing responses of 55.9 and 30.9% based on the band gap change and of 55.0 and 38.5% based on the energy gap change. The analysis of the density of state clearly shows the modified electronic property of the Ni-WSe2 monolayer in gas adsorptions. On the other hand, the analysis of the work function (WF) reveals the limited possibility to explore the Ni-WSe2 monolayer as a WF-based gas sensor for CO and HCHO detections. This work systemically studies the sensing potential of the Ni-WSe2 monolayer upon two typical gas species in the dry-type transformers, which is meaningful to explore novel nanomaterial-based gas sensors to monitor the operation condition of electrical equipment.

Trends and prospects of 2-D tungsten disulphide (WS2) hybrid nanosystems for environmental and biomedical applications

Recently, 2D layered transition metal dichalcogenides (TMDCs) with their ultrathin sheet nanostructure and diversified electronic structure have drawn attention for various advanced applications to achieve high-performance parameters. Unique 2D TMDCs mainly comprise transition metal and chalcogen element where chalcogen element layers sandwich the transition metal element layer. In such a case, various properties can be enhanced and controlled depending on the targeted application. Among manipulative 2D TMDCs, tungsten disulphide (WS2) is one of the emerging nano-system due to its fascinating properties in terms of direct band gap, higher mobility, strong photoluminescence, good thermal stability, and strong magnetic field interaction. The advancement in characterization techniques, especially scattering techniques, can help in study of opto-electronic properties of 2D TMDCs along with determination of layer variations and investigation of defect. In this review, the fabrication and applications are well summarized to optimize an appropriate WS2-TMDCs assembly according to focused field of research. Here, the scientific investigations on 2D WS2 are studied in terms of its structure, role of scattering techniques to study its properties, and synthesis routes followed by its potential applications for environmental remediation (e.g., photocatalytic degradation of pollutants, gas sensing, and wastewater treatment) and biomedical domain (e.g., drug delivery, photothermal therapy, biomedical imaging, and biosensing). Further, a special emphasis is given to the significance of 2D WS2 as a substrate for surface-enhanced Raman scattering (SERS). The discussion is further extended to commercial and industrial aspects, keeping in view major research gaps in existing research studies.

Transition metal (Ti, Cu, Zn, Pt) single-atom modified graphene/AS2 (A = Mo, W) van der Waals heterostructures for removing airborne pollutants

Air pollution is a worldwide issue that affects human health and the environment. The scientific community tries to control it through different approaches, from experimental to theoretical assessments. Here, we perform DFT calculations to describe CO2, NO2, and SO2 detection on a single-atom (Ti, Cu, Zn, Pt) graphene supported on 2D molybdenum disulfide (MoS2) and tungsten disulfide (WS2). Transition metal single atoms on graphene improve the monolayer reactivity by generating an effective way to remove airborne pollutants. Results indicate that SO2 and NO2 chemically adsorb on all tested transition metals, whereas CO2 stands on top of the incorporated atoms through van der Waals interactions. Since strong Ti-O interactions appear, the Ti single-atom graphene/MoS2(WS2) systems efficiently remove CO2 from the environment. Compared to pristine graphene, our proposed heterostructures improve the SO2, NO2, and CO2 adsorption energies. The heterostructures' electronic properties change once the molecules interact with the transition metals, generating sensible and selective pollutant molecule detection and removal.

In Situ Fabrication of SnS2/SnO2 Heterostructures for Boosting Formaldehyde-Sensing Properties at Room Temperature

Formaldehyde, as a harmful gas produced by materials used for decorative purposes, has a serious impact on human health, and is also the focus and difficulty of indoor environmental polution prevention; hence, designing and developing gas sensors for the selective measurement of formaldehyde at room temperature is an urgent task. Herein, a series of SnS2/SnO2 composites with hollow spherical structures were prepared by a facile hydrothermal approach for the purpose of formaldehyde sensing at room temperature. These novel hierarchical structured SnS2/SnO2 composites-based gas sensors demonstrate remarkable selectivity towards formaldehyde within the concentration range of sub-ppm (0.1 ppm) to ppm (10 ppm) at room temperature. Notably, the SnS2/SnO2-2 sensor exhibits an exceptional formaldehyde-sensing performance, featuring an ultra-high response (1.93, 0.1 ppm and 17.51, 10 ppm), as well as good repeatability, long-term stability, and an outstanding theoretical detection limit. The superior sensing capabilities of the SnS2/SnO2 composites can be attributed to multiple factors, including enhanced formaldehyde adsorption, larger specific surface area and porosity of the hollow structure, as well as the synergistic interfacial incorporation of the SnS2/SnO2 heterojunction. Overall, the excellent gas sensing performance of SnS2/SnO2 hollow spheres has opened up a new way for their detection of trace formaldehyde at room temperature.

Large-Area and Visible-Light-Driven Heterojunctions of In2O3/Graphene Built for ppb-Level Formaldehyde Detection at Room Temperature

Achieving convenient and accurate detection of indoor ppb-level formaldehyde is an urgent requirement to ensure a healthy working and living environment for people. Herein, ultrasmall In₂O₃ nanorods and supramolecularly functionalized reduced graphene oxide are selected as hybrid components of visible-light-driven (VLD) heterojunctions to fabricate ppb-level formaldehyde (HCHO) gas sensors (named InAG sensors). Under 405 nm visible light illumination, the sensor exhibits an outstanding response toward ppb-level HCHO at room temperature, including the ultralow practical limit of detection (pLOD) of 5 ppb, high response (R_a/R_g = 2.4, 500 ppb), relatively short response/recovery time (119 s/179 s, 500 ppb), high selectivity, and long-term stability. The ultrasensitive room temperature HCHO-sensing property is derived from visible-light-driven and large-area heterojunctions between ultrasmall In₂O₃ nanorods and supramolecularly functionalized graphene nanosheets. The performance of the actual detection toward HCHO is evaluated in a 3 m³ test chamber, confirming the practicability and reliability of the InAG sensor. This work provides an effective strategy for the development of low-power-consumption ppb-level gas sensors.

Environmental formaldehyde sensing at room temperature by smartphone-assisted and wearable plasmonic nanohybrids

Formaldehyde is a toxic and carcinogenic indoor air pollutant. Promising for its routine detection are gas sensors based on localized surface plasmon resonance (LSPR). Such sensors trace analytes by converting tiny changes in the local dielectric environment into easily readable, optical signals. Yet, this mechanism is inherently non-selective to volatile organic compounds (like formaldehyde) and yields rarely detection limits below parts-per-million concentrations. Here, we reveal that chemical reaction-mediated LSPR with nanohybrids of Ag/AgO_x core-shell clusters on TiO₂ enables highly selective formaldehyde sensing down to 5 parts-per-billion (ppb). Therein, AgO_x is reduced by the formaldehyde to metallic Ag resulting in strong plasmonic signal changes, as measured by UV/Vis spectroscopy and confirmed by X-ray diffraction. This interaction is highly selective to formaldehyde over other aldehydes, alcohols, ketones, aromatic compounds (as confirmed by high-resolution mass spectrometry), inorganics, and quite robust to relative humidity changes. Since this sensor works at room temperature, such LSPR nanohybrids are directly deposited onto flexible wristbands to quantify formaldehyde between 40-500 ppb at 50% RH, even with a widely available smartphone camera (Pearson correlation coefficient r = 0.998). Such chemoresponsive coatings open new avenues for wearable devices in environmental, food, health and occupational safety applications, as demonstrated by an early field test in the pathology of a local hospital.

Pd-Decorated WTe2 Monolayer as a Favorable Sensing Material toward SF6 Decomposed Species: A DFT Study

Based on density functional theory, this work first investigates the Pd-decorating property on the pristine WTe₂ monolayer and then simulates the adsorption performance of a Pd-decorated WTe₂ (Pd-WTe₂) monolayer on SO₂ and SOF₂ molecules, in order to explore its sensing potential for SF₆ decomposed species. It is found that the Pd atom can be stably anchored on the top of the W atom of the WTe₂ monolayer with a binding energy of -2.43 eV. The Pd-WTe₂ monolayer performs chemisorption on SO₂ and SOF₂, with adsorption energies of -1.36 and -1.17 eV, respectively. The analyses of the band structure and density of states reveal the deformed electronic property of the WTe₂ monolayer by Pd-decoration, as well as that of the Pd-WTe₂ monolayer by gas adsorption. The bandgap of the Pd-Wte₂ monolayer is increased by 1.6% in the SO₂ system and is decreased by -3.9% in the SOF₂ system, accounting for the sensing response of 42.0 and -56.7% for the detection of two gases. Moreover, the changed work function (WF) in two gas systems in comparison with that of the pristine Pd-WTe₂ monolayer suggests its potential as a WF-based gas sensor for sensing two gases as well. This paper uncovers the gas sensing potential of the Pd-WTe₂ monolayer to evaluate the operation status of SF₆ insulation devices, which also illustrates the strong potential of WTe₂-based materials for gas sensing applications in some other fields.

Eddy Current Measurement of Chemiresistive Sensing Transients in Graphene-hBN Heterostructures

The development of graphene-based electronic and gas sensing devices has motivated considerable research interest in the properties of graphene-hBN heterostructures. Eddy current measurements of the sheet conductance of graphene-hBN heterostructures show a relatively low conductance, as compared to results previously reported in the literature, all of which were obtained using contact-based measurement methods. Chemiresistive measurements of the graphene-hBN heterostructure response to oxygen adsorption, including hysteric effects under transient multicycle loading, show that the incremental sheet conductance responses of graphene and graphene-hBN sensors differ in sign. A transient, nonlinear, history dependent constitutive model of graphene-hBN response to oxygen adsorption distinguishes stochastic variations in material properties from deterministic variations in sensor performance. The deterministic variations are due to sensing process hysteresis, a phenomenon of central interest in the development of graphene-based sensor systems.

Gas sensing performance of In2O3 nanostructures: A mini review

Effective detection of toxic and hazardous gases is crucial for ensuring human safety, and high-performance metal oxide-based gas sensors play an important role in achieving this goal. In₂O₃ is a widely used n-type metal oxide in gas sensors, and various In₂O₃ nanostructures have been synthesized for detecting small gas molecules. In this review, we provide a brief summary of current research on In₂O₃-based gas sensors. We discuss methods for synthesizing In₂O₃ nanostructures with various morphologies, and mainly review the sensing behaviors of these structures in order to better understand their potential in gas sensors. Additionally, the sensing mechanism of In₂O₃ nanostructures is discussed. Our review further indicates that In₂O₃-based nanomaterials hold great promise for assembling high-performance gas sensors.

Effect of Different Solvents on Morphology and Gas-Sensitive Properties of Grinding-Assisted Liquid-Phase-Exfoliated MoS2 Nanosheets

Grinding-assisted liquid-phase exfoliation is a widely used method for the preparation of two-dimensional nanomaterials. In this study, N-methylpyrrolidone and acetonitrile, two common grinding solvents, were used during the liquid-phase exfoliation for the preparation of MoS₂ nanosheets. The morphology and structure of MoS₂ nanosheets were analyzed via scanning electron microscopy, X-ray diffraction, and Raman spectroscopy. The effects of grinding solvents on the gas-sensing performance of the MoS₂ nanosheets were investigated for the first time. The results show that the sensitivities of MoS₂ nanosheet exfoliation with N-methylpyrrolidone were 2.4-, 1.4-, 1.9-, and 2.7-fold higher than exfoliation with acetonitrile in the presence of formaldehyde, acetone, and ethanol and 98% relative humidity, respectively. MoS₂ nanosheet exfoliation with N-methylpyrrolidone also has fast response and recovery characteristics to 50-1000 ppm of CH₂O. Accordingly, although N-methylpyrrolidone cannot be removed completely from the surface of MoS₂, it has good gas sensitivity compared with other samples. Therefore, N-methylpyrrolidone is preferred for the preparation of gas-sensitive MoS₂ nanosheets in grinding-assisted liquid-phase exfoliation. The results provide an experimental basis for the preparation of two-dimensional materials and their application in gas sensors.

Noble-Nanoparticle-Decorated Ti3C2T x MXenes for Highly Sensitive Volatile Organic Compound Detection

Two-dimensional transition-metal carbides and nitrides (MXenes) have been regarded as promising sensing materials because of their high surface-to-volume ratios and outstanding electronic, optical, and mechanical properties with versatile transition-metal and surface chemistries. However, weak gas-molecule adsorption of MXenes poses a serious limitation to their sensitivity and selectivity, particularly for trace amounts of volatile organic compounds (VOCs) at room temperature. To deal with these issues, Au-decorated MXenes are synthesized by a facile solution mixing method for room-temperature sensing of a wide variety of oxygen-based and hydrocarbon-based VOCs. Dynamic sensing experiments reveal that optimal decoration of Au nanoparticles (NPs) on Ti₃C₂T _x MXene significantly elevates the response and selectivity of the flexible sensors, especially in detecting formaldehyde. Au-Ti₃C₂T _x gas sensors exhibited an extremely low limit of detection of 92 ppb for formaldehyde at room temperature. Au-Ti₃C₂T _x provides reliable gas response, low noise level, ultrahigh signal-to-noise ratio, high selectivity, as well as parts per billion level of formaldehyde detection. The prominent mechanism for Au-Ti₃C₂T _x in sensing formaldehyde is elucidated theoretically from density functional theory simulations. The results presented here strongly suggest that decorating noble-metal NPs on MXenes is a feasible strategy for the development of next-generation ultrasensitive sensors for Internet of Things.

Dissolved Gas Analysis in Transformer Oil Using Ni Catalyst Decorated PtSe2 Monolayer: A DFT Study

In this paper, the first-principles theory is used to explore the adsorption behavior of Ni catalyst decorated PtSe2 (Ni-PtSe2) monolayer toward the dissolved gas in transformer oil, namely CO and C2H2. Some Ni atoms from the catalyst are trapped in the Se vacancy on the pure PtSe2 surface. The geometry configurations of Ni-PtSe2 monolayer before and after gas adsorption, the electronic property of Ni-PtSe2 monolayer upon gas adsorption, and the sensibility and recovery property of Ni-PtSe2 monolayer are explored in this theoretical work. Through the simulation, the Ead of CO and C2H2 gas adsorption systems are calculated as −1.583 eV and −1.319 eV, respectively, both identified as chemisorption and implying the stronger performance of the Ni-PtSe2 monolayer on CO molecule, which is further supported by the DOS and BS analysis. According to the formula, the sensitivity of Ni-PtSe2 monolayer towards CO and C2H2 detection can reach up to 96.74% and 99.91% at room temperature (298 K), respectively, which manifests the favorable sensing property of these gases as a chemical resistance-type sensor. Recovery behavior indicates that the Ni-PtSe2 monolayer is a satisfied gas scavenger upon the noxious gas dissolved in transformer oil, but its recovery time at room temperature is not satisfactory. To sum up, we monitor the status of the transformer to guarantee the stable operation of the power system through the Ni-PtSe2 monolayer upon the detection of CO and C2H2, which may realize related applications, and provide the basis and reference to cutting-edge research in the field of electricity in the future.

Improved TEA Sensitivity and Selectivity of In2O3 Porous Nanospheres by Modification with Ag Nanoparticles

A highly sensitive and selective detection of volatile organic compounds (VOCs) by using gas sensors based on metal oxide semiconductor (MOS) has attracted increasing interest, but still remains a challenge in gas sensitivity and selectivity. In order to improve the sensitivity and selectivity of In2O3 to triethylamine (TEA), herein, a silver (Ag)-modification strategy is proposed. Ag nanoparticles with a size around 25–30 nm were modified on pre-synthesized In2O3 PNSs via a simple room-temperature chemical reduction method by using NaBH4 as a reductant. The results of gas sensing tests indicate that after functionalization with Ag, the gas sensing performance of In2O3 PNSs for VOCs, especially for TEA, was remarkably improved. At a lower optimal working temperature (OWT) of 300 °C (bare In2O3 sensor: 320 °C), the best Ag/In2O3-2 sensor (Ag/In2O3 PNSs with an optimized Ag content of 2.90 wt%) shows a sensitivity of 116.86/ppm to 1–50 ppm TEA, about 170 times higher than that of bare In2O3 sensor (0.69/ppm). Significantly, the Ag/In2O3-2 sensor can provide a response (Ra/Rg) as high as 5697 to 50 ppm TEA, which is superior to most previous TEA sensors. Besides lower OWT and higher sensitivity, the Ag/In2O3-2 sensor also shows a remarkably improved selectivity to TEA, whose selectivity coefficient (STEA/Sethanol) is as high as 5.30, about 3.3 times higher than that of bare In2O3 (1.59). The sensitization mechanism of Ag on In2O3 is discussed in detail.

Effective Air Purification via Pt-Decorated N3-CNT Adsorbent

Effectively removal of air pollutants using adsorbents is one of the most important methods to purify the air. In this work, we proposed for the first time that PtN3-CNT is an effective adsorbent for air purification. Its air purification performance was studied by calculating the adsorption behaviors and electronic structures of 12 gas molecules, including the main components of air (N2, O2, H2O, CO2) and the most common air pollutants (NO, NO2, SO3, SO2, CO, O3, NH3, H2S), on the surface of PtN3-CNT using first-principles calculations. The results showed that these gases were adsorbed stably via the coordination between Pt and the coordinated atoms (C, N, O, and S atoms) in the gas molecules, and the adsorption energies vary in the range of −0.81∼−4.28 eV. The obvious chemical interactions between PtN3-CNT and the adsorbed gas molecules are mainly determined by the apparent overlaps between the Pt 5d orbitals and the outmost p orbitals of the coordination atoms. PtN3-CNT has strong adsorption capacity for the toxic gas molecules, while relatively weaker adsorption performance for the main components of the air except oxygen. The recovery time of each adsorbed molecule calculated at different temperatures showed that, CO2, H2O, and N2 can be desorbed gradually at 298∼498 K, while the toxic gases are always adsorbed stably on the surface of PtN3-CNT. Considering the excellent thermal stability of PtN3-CNT at up to 1000 K proved by AIMD, PtN3-CNT is very suitable to act as an adsorbent to remove toxic gases to achieve the purpose of air purification. Our findings in this report would be beneficial for exploiting possible carbon-based air purification adsorbents with excellent adsorbing ability and good recovery performance.

Density Functional Investigation on α-MoO3 (100): Amines Adsorption and Surface Chemistry

The (100) surface of α-MoO₃ should possess overwhelmingly more exposed Mo atoms than the (010), and the exposed Mo has been extensively considered as an active site for amine adsorption. However, α-MoO₃ (100) has drawn little attention concerning the amine sensing mechanism. In this research, adsorption of ammonia (NH₃), monomethylamine (MMA), dimethylamine (DMA), and trimethylamine (TMA) is systematically investigated by density functional theory (DFT). All four of these molecules have high affinity to α-MoO₃ (100) through interaction between the N and the exposed Mo, and the affinity is mainly influenced by both the characteristics of the molecules and the geometric environment of the surface active site. Adsorption and dissociation of water and oxygen molecule on stoichiometric and defective α-MoO₃ (100) surfaces are then simulated to fully understand the surface chemistry of α-MoO₃ (100) in practical conditions. At low temperature, α-MoO₃ (100) must be covered with a large number of water molecules; the water can desorb or dissociate into hydroxyl groups at high temperature. Oxygen vacancy (V_O) can be generated through the annealing process during sensor device fabrication; V_O must be filled with an O₂ molecule, which can further interact with adsorbed water nearby to form hydroxyl groups. According to this research, α-MoO₃ (100) must be the active surface for amine sensing and its surface chemistry is well understood. In the near future, further reaction and interaction will be simulated at α-MoO₃ (100), and much more attention should be paid to α-MoO₃ (100) not only theoretically but also experimentally.

Assembling Hollow Cactus-Like ZnO Nanorods with Dipole-Modified Graphene Nanosheets for Practical Room-Temperature Formaldehyde Sensing

Formaldehyde (HCHO) sensing plays a critical role for indoor environment monitoring in smart home systems. Inspired by the unique hierarchical structure of cactus, we have prepared a ZnO/ANS-rGO composite for room-temperature (RT) HCHO sensing, through assembling hollow cactus-like ZnO nanorods with 5-aminonaphthalene-1-sulfonic acid (ANS)-modified graphene nanosheets in a facile and template-free manner. Interestingly, it was found that the ZnO morphology could be simply tuned from flower clusters to hollow cactus-like nanostructures, along with the increase of the reaction time during the assembly process. The ZnO/ANS-rGO-based sensors exhibited superior RT HCHO-sensing performance with an ultrahigh response (68%, 5 ppm), good repeatability, long-term stability, and an outstanding practical limit of detection (LOD: 0.25 ppm) toward HCHO, which is the lowest practical LOD reported so far. Furthermore, for the first time, a 30 m³ simulation test cabinet was adapted to evaluate the practical gas-sensing performance in an indoor environment. As a result, an instantaneous response of 5% to 0.4 ppm HCHO was successfully achieved in the simulation test. The corresponding sensing mechanism was interpreted from two aspects including high charge transport capability of ANS-rGO and the distinct gas adsorbability derived from nanostructures, respectively. The combination of a biomimetic hierarchical structure and supramolecular assembly provides a promising strategy to design HCHO-sensing materials with high practicability.

A highly stable and sensitive ethanol sensor based on Ru-decorated 1D WO3 nanowires

Decorating materials with noble metal catalysts is an effective method for optimizing the sensing performance of sensors based on tungsten trioxide (WO₃) nanowires. Ruthenium (Ru) exhibits excellent catalytic activity for oxygen adsorption/desorption and chemical reactions between gases and adsorbed oxygen. Herein, small Ru nanoparticles were uniformly distributed on the surface of one-dimensional WO₃ nanowires. The nanowires were prepared by the electrospinning method through an ultraviolet (UV) irradiation process, and decoration with Ru did not change their morphology. A sensor based on 4% Ru nanowires (NWs) shows the highest response (∼120) to 100 ppm ethanol, which was increased around 47 times, and the lowest ethanol detection limit (221 ppb) at a lower temperature (200 °C) displays outstanding repeatability and stability even after 45 days or in higher-humidity conditions. Moreover, it also has faster response–recovery features. The improvement in the sensing performance was attributed to the stable morphology of the nanowires, the sensitization effect of Ru, the catalytic effect of RuO₂ and the optimal atomic utilization efficiency. This work offers an effective and promising strategy for promoting the ethanol sensing performance of WO₃.

Decorating Ru does not effect the morphology of NWs, increased the oxygen vacancies, adsorbed oxygen. This strategy results in a better sensing performance (∼120 to 100 ppm ethanol was increased around 47 times at 200 °C) and humidity resistance.

Dopant-Tunable Ultrathin Transparent Conductive Oxides for Efficient Energy Conversion Devices

Ultrathin film-based transparent conductive oxides (TCOs) with a broad work function (WF) tunability are highly demanded for efficient energy conversion devices. However, reducing the film thickness below 50 nm is limited due to rapidly increasing resistance; furthermore, introducing dopants into TCOs such as indium tin oxide (ITO) to reduce the resistance decreases the transparency due to a trade-off between the two quantities. Herein, we demonstrate dopant-tunable ultrathin (≤ 50 nm) TCOs fabricated via electric field-driven metal implantation (m-TCOs; m = Ni, Ag, and Cu) without compromising their innate electrical and optical properties. The m-TCOs exhibit a broad WF variation (0.97 eV), high transmittance in the UV to visible range (89-93% at 365 nm), and low sheet resistance (30-60 Ω cm^-2). Experimental and theoretical analyses show that interstitial metal atoms mainly affect the change in the WF without substantial losses in optical transparency. The m-ITOs are employed as anode or cathode electrodes for organic light-emitting diodes (LEDs), inorganic UV LEDs, and organic photovoltaics for their universal use, leading to outstanding performances, even without hole injection layer for OLED through the WF-tailored Ni-ITO. These results verify the proposed m-TCOs enable effective carrier transport and light extraction beyond the limits of traditional TCOs.

Nitrogen Dioxide Gas Sensor Based on Ag-Doped Graphene: A First-Principle Study

High-performance tracking trace amounts of NO2 with gas sensors could be helpful in protecting human health since high levels of NO2 may increase the risk of developing acute exacerbation of chronic obstructive pulmonary disease. Among various gas sensors, Graphene-based sensors have attracted broad attention due to their sensitivity, particularly with the addition of noble metals (e.g., Ag). Nevertheless, the internal mechanism of improving the gas sensing behavior through doping Ag is still unclear. Herein, the impact of Ag doping on the sensing properties of Graphene-based sensors is systematically analyzed via first principles. Based on the density-functional theory (DFT), the adsorption behavior of specific gases (NO2, NH3, H2O, CO2, CH4, and C2H6) on Ag-doped Graphene (Ag–Gr) is calculated and compared. It is found that NO2 shows the strongest interaction and largest Mulliken charge transfer to Ag–Gr among these studied gases, which may directly result in the highest sensitivity toward NO2 for the Ag–Gr-based gas sensor.

Strategies for Improving the Sensing Performance of Semiconductor Gas Sensors for High-Performance Formaldehyde Detection: A Review

Formaldehyde is a poisonous and harmful gas, which is ubiquitous in our daily life. Long-term exposure to formaldehyde harms human body functions; therefore, it is urgent to fabricate sensors for the real-time monitoring of formaldehyde concentrations. Metal oxide semiconductor (MOS) gas sensors is favored by researchers as a result of their low cost, simple operation and portability. In this paper, the mechanism of formaldehyde detection by gas sensors is introduced, and then the ways of ameliorating the response of gas sensors for formaldehyde detection in recent years are summarized. These methods include the control of the microstructure and morphology of sensing materials, the doping modification of matrix materials, the development of new semiconductor sensing materials, the outfield control strategy and the construction of the filter membrane. These five methods will provide a good prerequisite for the preparation of better performing formaldehyde gas sensors.

Tailoring Unsymmetrical-Coordinated Atomic Site in Oxide-Supported Pt Catalysts for Enhanced Surface Activity and Stability

The catalytic properties of supported metal heterostructures critically depend on the design of metal sites. Although it is well-known that the supports can influence the catalytic activities of metals, precisely regulating the metal-support interactions to achieve highly active and durable catalysts still remain challenging. Here, the authors develop a support effect in the oxide-supported metal monomers (involving Pt, Cu, and Ni) catalysts by means of engineering nitrogen-assisted nanopocket sites. It is found that the nitrogen-permeating process can induce the reconstitution of vacancy interface, resulting in an unsymmetrical atomic arrangement around the vacancy center. The resultant vacancy framework is more beneficial to stabilize Pt monomers and prevent diffusion, which can be further verified by the density functional theory calculations. The final Pt-N/SnO₂ catalysts exhibit superior activity and stability for HCHO response (26.5 to 15 ppm). This higher activity allows the reaction to proceed at a lower operating temperature (100 °C). Incorporated with wireless intelligent-sensing system, the Pt-N/SnO₂ catalysts can further achieve continuous monitoring of HCHO levels and cloud-based terminal data storage.

0D/2D CdS/ZnO composite with n-n heterojunction for efficient detection of triethylamine

It is imperative to seek for novel materials with pronounced gas sensing performance towards triethylamine for the sake of human health. Herein, we successfully fabricate an outstanding triethylamine sensor based on CdS/ZnO composite with 0D/2D structure, which are prepared by in-situ growth of CdS quantum dots on ultra-thin ZnO nanosheets. The ratios between the two ingredients are adjusted and their effect is evaluated. The optimal sample exhibits the lowest operating temperature of 200 °C, the highest response value of ~20 and the fastest response time of 2 s. Besides, it also has the virtues of durable stability, excellent selectivity and superior anti-interference ability. The mechanism behind the aforementioned intriguing performance is investigated by X-ray photoelectron spectroscopy, Kelvin probe and density function theory (DFT) simulation. All the results verify that the enhanced gas sensing properties are derived from splendid 0D/2D structure, n-n heterojunction and large specific surface area. Additionally, this study opens an avenue for designing sensors with 0D/2D structure.

A Formaldehyde Sensor Based on Self-Assembled Monolayers of Oxidized Thiophene Derivatives

High-performance formaldehyde sensors play an important role in air quality assessment. Herein, a self-assembled monolayer (SAM) sensor for trace formaldehyde (FA) is fabricated based on the fluorescence enhancement of oxidized thiophene derivatives. In the primary SAM molecules, the functional backbone trithiophene (3T) links to the anchor through an n-propyl group. The anchor with an active Si-Cl bond can form a covalent bond with the SiO₂ substrate by solution incubation, which ensures good stability against organic solvents and high sensitivity via monolayer structures. With the alkyl chain's leading, a dense 3T SAM can be obtained on SiO₂. Upon exposure to UV light in the presence of oxygen, 3T can be oxidized into a nonfluorescent but coordination-active product with abundant carbonyl groups, which can be doped with FA and induce a blueshifted fluorescence. With this mechanism, we proposed an SAM-based FA sensor by detecting the enhancement of the blueshifted fluorescence. Reliable reversibility, selectivity, stability, and detection limit lower than 1 ppm are achieved in this system. The work provides an experimental basis for developing a cheap, efficient, and flexible sensor for trace FA detection.

Tunable NH4F-Assisted Synthesis of 3D Porous In2O3 Microcubes for Outstanding NO2 Gas-Sensing Performance: Fast Equilibrium at High Temperature and Resistant to Humidity at Room Temperature

NO₂ gas sensors based on metal oxides under wild conditions are highly demanded yet an incomplete surface reaction and humidity interference on the gas-sensing performance limit their applications. Herein, we report three-dimensional (3D) porous In₂O₃ microcubes via a simple hydrothermal strategy to produce outstanding NO₂ gas-sensing performance: fast equilibrium of the surface reaction at 150 °C and negligible humidity dependence on the NO₂ gas sensing at room temperature. The 3D porous In₂O₃ microcubes with high surface areas, suitable pore sizes, rich oxygen vacancies, and high conductivity are testified. The underlying structural transformation mechanism for 3D porous In₂O₃ is investigated in detail. The as-made 3D porous In₂O₃ microcubic gas sensors present excellent gas-sensing performance to 50 ppm NO₂ at 150 °C, including a high response value (2329), fast response/recovery time (10/9 s), a low detection limit (10 ppb), long-term stability (60 days), and strong selectivity. Furthermore, they exhibit relatively stable NO₂ gas response under humidity variation (20-80%). The NO₂ gas mechanism under the interference of water is also clarified.

Nanoengineering Approaches Toward Artificial Nose

Significant scientific efforts have been made to mimic and potentially supersede the mammalian nose using artificial noses based on arrays of individual cross-sensitive gas sensors over the past couple decades. To this end, thousands of research articles have been published regarding the design of gas sensor arrays to function as artificial noses. Nanoengineered materials possessing high surface area for enhanced reaction kinetics and uniquely tunable optical, electronic, and optoelectronic properties have been extensively used as gas sensing materials in single gas sensors and sensor arrays. Therefore, nanoengineered materials address some of the shortcomings in sensitivity and selectivity inherent in microscale and macroscale materials for chemical sensors. In this article, the fundamental gas sensing mechanisms are briefly reviewed for each material class and sensing modality (electrical, optical, optoelectronic), followed by a survey and review of the various strategies for engineering or functionalizing these nanomaterials to improve their gas sensing selectivity, sensitivity and other measures of gas sensing performance. Specifically, one major focus of this review is on nanoscale materials and nanoengineering approaches for semiconducting metal oxides, transition metal dichalcogenides, carbonaceous nanomaterials, conducting polymers, and others as used in single gas sensors or sensor arrays for electrical sensing modality. Additionally, this review discusses the various nano-enabled techniques and materials of optical gas detection modality, including photonic crystals, surface plasmonic sensing, and nanoscale waveguides. Strategies for improving or tuning the sensitivity and selectivity of materials toward different gases are given priority due to the importance of having cross-sensitivity and selectivity toward various analytes in designing an effective artificial nose. Furthermore, optoelectrical sensing, which has to date not served as a common sensing modality, is also reviewed to highlight potential research directions. We close with some perspective on the future development of artificial noses which utilize optical and electrical sensing modalities, with additional focus on the less researched optoelectronic sensing modality.

Adsorption of atmospheric gas molecules (NH3, H2S, CO, H2, CH4, NO, NO2, C6H6 and C3H6O) on two-dimensional polyimide with hydrogen bonding: a first-principles study

In this study, we investigated the effects of hydrogen bond acceptors on the surface of two-dimensional polyimide towards NH₃, H₂S, CO, H₂, CH₄, NO, NO₂, C₆H₆ and C₃H₆O gas molecules through first-principles study based on density functional theory.

Alkali metal-incorporated spinel oxide nanofibers enable high performance detection of formaldehyde at ppb level

Sensing material with high sensitivity, excellent selectivity and ultra-low detection limit is crucial for monitoring formaldehyde, which is a kind of hazardous gas to human health at very low concentration. Some one-dimensional semiconductor metal oxides show acceptable responses towards formaldehyde. However, the detection limit and selectivity of these sensors are still not satisfied, especially at ppb level. Herein, alkali metals (K, Na) doped CdGa₂O₄ nanofibers with excellent formaldehyde sensing performance are prepared by an electrospinning method. These nanofibers have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), electron paramagnetic resonance spectroscopy (EPR), elemental mapping and other techniques. As a result, the sensor based on 7.5 at.% K doped CdGa₂O₄ gives remarkably improved formaldehyde sensing properties compared with that of pristine CdGa₂O₄. The greatly increased sensitivity and selectivity should be attributed to the increased chemisorbed oxygen and the enhanced basicity caused by the additional alkali metal, respectively. All in all, the 7.5 at.% K doped CdGa₂O₄ is a good candidate for the rapid detecting formaldehyde at ppb level.

Tellurene Nanoflake-Based NO2 Sensors with Superior Sensitivity and a Sub-Parts-per-Billion Detection Limit

Industrial production, environmental monitoring, and clinical medicine put forward urgent demands for high-performance gas sensors. Two-dimensional (2D) materials are regarded as promising gas-sensing materials owing to their large surface-to-volume ratio, high surface activity, and abundant surface-active sites. However, it is still challenging to achieve facilely prepared materials with high sensitivity, fast response, full recovery, and robustness in harsh environments for gas sensing. Here, a combination of experiments and density functional theory (DFT) calculations is performed to explore the application of tellurene in gas sensors. The prepared tellurene nanoflakes via facile liquid-phase exfoliation show an excellent response to NO₂ (25 ppb, 201.8% and 150 ppb, 264.3%) and an ultralow theory detection limit (DL) of 0.214 ppb at room temperature, which is excellent compared to that of most reported 2D materials. Furthermore, tellurene sensors present a fast response (25 ppb, 83 s and 100 ppb, 26 s) and recovery (25 ppb, 458 s and 100 ppb, 290 s). The DFT calculations further clarify the reasons for enhanced electrical conductivity after NO₂ adsorption because of the interfacial electron transfer from tellurene to NO₂, revealing an underlying explanation for tellurene-based gas sensors. These results indicate that tellurene is eminently promising for detecting NO₂ with superior sensitivity, favorable selectivity, an ultralow DL, fast response-recovery, and high stability.

ZnO Metal Oxide Semiconductor in Surface Acoustic Wave Sensors: A Review

Surface acoustic wave (SAW) gas sensors are of continuous development interest to researchers due to their sensitivity, short detection time, and reliability. Among the most used materials to achieve the sensitive film of SAW sensors are metal oxide semiconductors, which are highlighted by thermal and chemical stability, by the presence on their surface of free electrons and also by the possibility of being used in different morphologies. For different types of gases, certain metal oxide semiconductors are used, and ZnO is an important representative for this category of materials in the field of sensors. Having a great potential for the development of SAW sensors, the discussion related to the development of the sensitivity of metal oxide semiconductors, especially ZnO, by the synthesis method or by obtaining new materials, is suitable and necessary to have an overview of the latest results in this domain.