Bioproduced Polymers Self-Assemble with Graphene Oxide into Nanocomposite Films with Enhanced Mechanical Performance

Study of Low Temperature-Treated Aldolized Cellulose Nanocrystals for Enhancing Dye Separation and Self-Healing Properties of Graphene Oxide Membranes

Graphene oxide (GO) membranes with a 2D layered structure and nanoscale channels have great application prospects for dye wastewater purification. In this paper, ethylenediamine (EDA) was grafted onto the surface of GO nanosheets at 70 °C and aldolized cellulose nanocrystals (ICNC) were introduced to form EDA-ICNC hydrogel structures between the GO nanosheets by Schiff base reaction. The interlayer structure of the membrane was determined by adjusting the amount of ICNC added and the degree of aldolization, and the EGOICNC-24 membrane with the best performance was prepared. The water flux is not only 12 times higher than that of GO membrane but also has a good separation ability for dye molecules with a molecular weight around 300. Following the EDA-ICNC-24 hydrogel cross-linking process, the tensile strength of the EGOICNC-24 membrane exhibited a 173% increase relative to that of the GO membrane. Additionally, the dye rejection rate reached 97.16% after 130 h of dye separation. When the surface of the membrane was damaged, it was self-healed by regulating the repair temperature and adding a very small amount of ICNC to undergo a dynamic Schiff base reaction and a synergistic effect of hydrogen bonding.

Enhanced Self-Assembly and Spontaneous Separation for Ultrathin, Air‒Floating Graphene Macrofilms and their Application in Ultrasensitive In-Site Growth Sensors

Self-assembled graphene films at air-liquid interface have great potential for multiple applications. However, the large size and ultrathin thickness for graphene-based films are hardly achieved simultaneously because of poor assembly ability of graphene oxide (GO) and cautious film transfer process (FTP). Herein, the ethanol-based binary solution with supramolecular clusters and weak polarity is introduced to enhance the assembly performance of GO. In this regime, GO film is formed within 52 s, and its formation temperature can be as low as -20 °C. More importantly, the attractive force between the formed GO film and this binary solution is 62% lower than that between GO film and traditional aqueous solution. On this basis, for the first time a spontaneous separation of the self-assembled GO film from solution is reported, and the air‒floating graphene films (AGFs) with nanoscale thickness and centimeter-scale diameter are prepared without FTP. By means of this separation behavior, the in situ growth AGFs sensors are fabricated, and they express fast response and ultrahigh sensitivity to imperceptible change in temperature and disturbances that are hardly recognized by common sensors. Therefore, a new accessible strategy is demonstrated to prepare ultrathin graphene macrofilms, which can be the excellent candidates for multifunctional, ultrasensitive sensors.

Triggering Redox Active Sites Through Electronic Structure Modulation in rGO Encapsulated Mixed Transition Metal Oxides Hybrid for Alkaline Hydrogen Evolution

Designing and developing noble-metal-free catalysts are of current interest in clean hydrogen generation via water splitting. As carbonaceous species are ideal choices as templates for various electrocatalysis, an improved synthetic route and an in-depth understanding of their electrochemical performance are essential. Herein, we have investigated the catalytic performance of rGO-encapsulated Mn and V mixed oxide hybrid structures (MVG) on a NiFeP matrix, focusing on their potential for catalyzing hydrogen evolution in an alkaline environment. The hierarchical MVG hollow microspheres hybrids are synthesized via a simple one-step in situ solvothermal method and MVG/NiFeP coatings are developed by facile electroless plating technique. As evidenced from the X-ray photoelectron spectroscopy, the multiple redox active sites in the 3d-band of Mn and V in MVG hybrid structural coatings serve as electron pumps, and rGO facilitates electronic conductions during catalytic reactions. The modulated electronic structure and strong synergistic effects between NiFeP and MVG facilitate rapid electron transfer kinetics, and the hybrids demonstrate superior HER performance. Consequently, the structural hybrid coatings possess an enhanced electronic conducting path (lower RCT = 545.3 Ω) and large ECSA values with a lower overpotential of 85 mV at 10 mA cm-2 and a reduced Tafel slope of 64.1 mV dec-1 with Volmer-Heyrovsky mechanism in alkaline media.

Enhanced physiochemical, antibacterial, and hemostatic performance of collagen-quaternized chitosan-graphene oxide sponges for promoting infectious wound healing

Bacteria-infected wound healing has attracted widespread attention in biomedical engineering. Wound dressing is a potential strategy for repairing infectious wounds. However, the development of wound dressing with appropriate physiochemical, antibacterial, and hemostatic properties, remains challenging. Hence, there is a motivation to develop new synthetic dressings to improve bacteria-infected wound healing. Here, we fabricate a biocompatible sponge through the covalent crosslinking of collagen (Col), quaternized chitosan (QCS), and graphene oxide (GO). The resulting Col-QCS-GO sponge shows an elastic modulus of 1.93-fold higher than Col sponge due to enhanced crosslinking degree by GO incorporation. Moreover, the fabricated Col-QCS-GO sponge shows favorable porosity (84.30 ± 3.12 %), water absorption / retention (2658.0 ± 113.4 % / 1114.0 ± 65.7 %), and hemostasis capacities (blood loss <50.0 mg). Furthermore, the antibacterial property of the Col-QCS-GO sponge under near-infrared (NIR) irradiation is significantly enhanced (the inhibition rates are 99.9 % for S. aureus and 99.9 % for E. coli) due to the inherent antibacterial properties of QCS and the photothermal antibacterial capabilities of GO. Finally, the Col-QCS-GO+NIR sponge exhibits the lowest percentage of wound area (9.05 ± 1.42 %) at day 14 compared to the control group (31.61 ± 1.76 %). This study provides new insights for developing innovative sponges for bacteria-infected wound healing.

Direct-Write Printed Slippery Surface for Assembling a High-Quality Graphene Structure and Its Application in Flexible Electric Actuators

Graphene is a two-dimensional honeycomb-like nanomaterial generated by carbon atoms in sp2 hybridized orbitals to form a hexagonal lattice structure with excellent electrical, optical, and mechanical properties. The solution process method has been widely used to realize large-area patterned graphene structures for high-performance devices. In the method, graphene usually needs to be dispersed in solution, and the π-π bonding gravitational interactions between graphene sheets would lead to uncontrollable structures in solution and difficulty in obtaining high performance. In this work, a patterned graphene oxide (GO) structure with controllable thickness and layer spacing was realized by a direct-write printed slippery surface, which was used as a slippery limited template. After reducing GO into reduced graphene oxide (rGO), a flexible electric pattern with a conductivity of up to 6.425 × 103 S/m was realized. Furthermore, the patterned rGO structure was transferred on polydimethylsiloxane (PDMS), which could generate less than a 5% change in resistance after 10,000 consecutive bends, and an anisotropic expansion based on rGO and PDMS materials under electro-thermal coupling. The patterned rGO structures could meet the performance requirements of highly sensitive and complex deformation applications as flexible electric actuators. This study provides great research significance and application value for patterning high-quality graphene structures and realizing high-performance flexible electronic devices.

Realizing Spontaneously Regular Stacking of Pristine Graphene Oxide by a Chemical-Structure-Engineering Strategy for Mechanically Strong Macroscopic Films

Mechanical-electrical properties of macroscopic graphene films derived from graphene oxide (GO) sheets are substantially restricted by their surface wrinkles and structural misalignment. Herein, we propose a chemical-structure-engineering strategy to realize the spontaneously regular stacking of modified GO (GO-m) with trace carboxyl. The highly aligned GO-m film delivers a fracture strength and modulus of nearly 3- and 5-fold higher than a wrinkled film with conventional Hummer's method derived GO (GO-c). The favorable assembly pattern of GO-m sheets is attributed to their decreased interfacial friction on the atomic scale, which weakens their local gelation capability for freer configuration adjustment during the assembly process. The chemical structure of GO-m can be further engineered by an epoxide-to-hydroxyl reaction, achieving a record high tensile strength of up to 631 MPa for the pristine GO film. By exploring the relationship between the surface terminations of GO and its stacking mode, this work proves the feasibility to realize high-performance macroscopic materials with optimized microstructure through the chemical modulation of nanosheet assembly.

Pearl-inspired graphene oxide-collagen microgel with multi-layer mineralization through microarray chips for bone defect repair

Biomineralization of natural polymers in simulated body fluid (SBF) can significantly improve its biocompatibility, osteoconductivity, and osteoinductivity because of the hydroxyapatite (HAp) deposition. Nevertheless, the superficial HAp crystal deposition hamper the deep inorganic ions exchange in porous microgels, thus gradually leading to a nonuniform regeneration effect. Inspired by the pearl forming process, this article uses the microarray chips to fabricate the multi-layer mineralized graphene oxide (GO)-collagen (Col)-hydroxyapatite (HAp) microgel, denoted as MMGCH. These fabricated MMGCH microgels exhibit porous structure and uniform HAp distribution. Furthermore, the suitable microenvironment offered by microgel promotes the time-dependent proliferation and osteogenic differentiation of stem cells, which resulted in upregulated osteogenesis-related genes and proteins, such as alkaline phosphatase, osteocalcin, and collagen-1. Finally, the MMGCH microgels possess favorable bone regeneration capacities both in cranial bone defects and mandibular bone defects via providing a suitable microenvironment for host-derived cells to form new bone tissues. This work presents a biomimetic means aiming to achieve full-thickness and uniform HAp deposition in hydrogel for bone defect repair.

Pistachio-Inspired Bulk Graphene Oxide-Based Materials with Shapeability and Recyclability

Nowadays, despite the fact that recent progress has been reported to mimic natural structural materials (especially nacre), designing bioinspired ultrastrong composites in a universal, viable, and scalable manner still remains a long-standing challenge. In particular, pistachio shells show high tissue strength attributed to the cellulose sheet laminated microstructures. Compared with nacre, pistachio shells own interlocking mortise-tenon joints in their structure, which offer higher energy dissipation and deformability. Here we present a strategy to produce nanocomposites with pistachio-mimetic structures through repeated kneading of graphene oxide (GO) in a dynamic covalent and supramolecular poly(sodium thioctic) (pST) system. The dynamic nature of the polymeric backbones endows the resultant GO-based composite with full recyclability and three-dimensional shapeability. The superior mechanical properties of the pistachio-mimetic composite can be attributed to the mortise-tenon joints design in the structure, which has not been achieved in the nacre-mimetic composite. The resulting composite also exhibits high thermal conductivity (15.6 W/(m·K)), yielding an alternative approach to design in engineered and thermal management materials.

Adsorption desulfurization performance of PdO/SiO2@graphene oxide hybrid aerogel: Influence of graphene oxide

Preparation of PdO/SiO₂@graphene oxide (GO) hybrid aerogels were carried out sol-gel method combined with atmospheric drying technology to study their adsorption performance for thiophenics and compared with PdO/SiO₂. Scanning electron microscope (SEM), N₂ adsorption-desorption isotherms, X-ray diffraction (XRD) analysis, X-ray photoelectron spectroscopy (XPS), and fourier transformation infrared spectroscopy (FT-IR) for samples were performed. The adsorption performance of PdO/SiO₂@GO for thiophene were better than that of PdO/SiO₂, attributed to that incorporation of GO increased the specific surface area and the Pd incorporation rate, where Pd²⁺ ions acted as the π-complexation and sulfur-metal (SM) bond adsorption active centers, as well as GO adsorbed thiophene by the π-π stacking effect. The adsorption capacities of PdO/SiO₂@GO-1.0 for thiophene (TH), benzothiophene (BT) and dibenzothiophene (DBT) were 8.89, 9.3 and 12.6 mg-S/g_ads, respectively. The addition of GO in aerogels could improve the inhibition effect of toluene, cyclohexene and pyridine while decreased the inhibition effect of MTBE and H₂O for the adsorption of thiophene, due to the π-π stacking effect and the hydrophobicity of GO, respectively. The adsorption process was spontaneous and exothermic, be well fitted by the apparent second-order kinetic model and dominated by chemical interaction. Pd/SiO₂@GO-1.0 had a good solvent elution regeneration performance.

Graphene-Based Films: Fabrication, Interfacial Modification, and Applications

Graphene-based film attracts tremendous interest in many potential applications due to its excellent thermal, electrical, and mechanical properties. This review focused on a critical analysis of fabrication, processing methodology, the interfacial modification approach, and the applications of this novel and new class material. Strong attention was paid to the preparation strategy and interfacial modification approach to improve its mechanical and thermal properties. The overview also discussed the challenges and opportunities regarding its industrial production and the current status of the commercialization. This review showed that blade coating technology is an effective method for industrial mass-produced graphene film with controllable thickness. The synergistic effect of different interface interactions can effectively improve the mechanical properties of graphene-based film. At present, the application of graphene-based film on mobile phones has become an interesting example of the use of graphene. Looking for more application cases is of great significance for the development of graphene-based technology.

Microscopically tuning the graphene oxide framework for membrane separations: a review

Membrane-based separations have been widely applied in gas, water and organic solvent purifications to reduce energy consumption and minimize environmental pollution. In recent years, graphene oxide (GO) membranes have attracted increasing attention due to their self-assembly ability and excellent stability. In this review, publications within the last 3 years on microscopically tuning the GO framework are summarized and reviewed. Various materials, including organic molecules, polymers, inorganic particles, ions and 2D materials, have been deployed to intercalate with GO nanosheets. Due to the varied interlayer spacing and packing structure, the developed GO composites exhibit enhanced stabilities and separation performances. In addition, designing horizontal GO membranes and functionalizing GO nanosheets have also been reported to improve the performance. This review sheds light on the techniques to microscopically tune the GO framework and the resulting macroscopic changes in membrane properties and performances.