3D Sodiophilic Ti3C2 MXene@g-C3N4 Hetero-Interphase Raises the Stability of Sodium Metal Anodes

Transient paper-based electrochemical biosensor Fabricated by superadditive Cu-TCPP(Fe)/Mxene for Multipathway non-invasive, highly sensitive detection of Bodily metabolites

Current advances in non-invasive fluid diagnostics highlight unique benefits for monitoring metabolic diseases. However, the low concentrations and complex compositions of biomarkers in fluids such as sweat, urine, and saliva impose stringent demands on the sensitivity and stability of detection technologies. Here, we developed a high-sensitivity, low-cost instantaneous electrochemical sensor based on the superadditive effect mechanism of Cu-TCPP(Fe)/Mxene (MMs Paper-ECL Sensor), which has been successfully applied for the simultaneous real-time detection of glucose and uric acid. Strong interfacial interactions between Mxene and Cu-TCPP(Fe) were revealed through precise simulation calculations and multi-dimensional characterization analysis, significantly enhancing the sensor's electrocatalytic performance and reaction kinetics. Experimentally, this exceptional electrocatalytic activity was demonstrated in its unprecedented high sensitivity and wide linear detection range for glucose and uric acid, with a non-invasive linear range from 0.001 nM to 5 mM, 0.025 nM-5 mM, detection limits as low as 1.88 aM and 5.80 pM, and stability extending up to 100 days. This represents not only a breakthrough in sensitivity and stability but also provides an effective, low-cost solution that overcomes the limitations of existing electronic devices, enabling multi-channel simultaneous detection. The universality of this sensor holds vast potential for application in the field of non-invasive fluid diagnostics.

Porous organic polymers assisted aptamer signal amplification for enhanced photoeletrochemical detection of MUC1

Mucin1 (MUC1) is an extensively glycosylated transmembrane protein that is widely distributed and overexpressed on the surface of cancer cells, playing an important role in tumor occurrence and metastasis. Therefore, highly sensitive detection of MUC1 is of great significance for early diagnosis, treatment monitoring, and prognosis of cancer. Here, an ultra-sensitive photoelectrochemical (PEC) sensing platform was developed based on an aptamer amplification strategy for highly selective and sensitive detection of MUC1 overexpressed in serum and on cancer cell surfaces. The sensing platform utilized copper phthalocyanine to fabricate porous organic polymers (CuPc POPs), and was effectively integrated with g-C3N4/MXene to form a ternary heterojunction material (g-C3N4/MXene/CuPc POPs). This material effectively improved electron transfer capability, significantly enhanced light utilization, and greatly enhanced photoelectric conversion efficiency, resulting in a dramatic increase in photocurrent response. MUC1 aptamer 1 was immobilized on a chitosan-modified photoelectrode for the selective capture of MUC1 or MCF-7 cancer cells. When the target substance was present, MUC1 aptamer 2 labeled with methylene blue (MB) was specifically adsorbed on the electrode surface, leading to enhanced photocurrent. The concentration of MUC1 directly correlated with the number of MB molecules attracted to the electrode surface, establishing a linear relationship between photocurrent intensity and MUC1 concentration. The PEC biosensor exhibited excellent sensitivity for MUC1 detection with a wide detection range from 1 × 10-7 to 10 ng/mL and a detection limit of 8.1 ag/mL. The detection range for MCF-7 cells was from 2 × 101 to 2 × 106 cells/mL, with the capability for detecting single MCF-7 cells. The aptamer amplification strategy significantly enhanced PEC performance, and open up a promising platform to establish high selectivity, stability, and ultrasensitive analytical techniques.

Regulating Sodium Deposition Behavior by a Triple-Gradient Framework for High-Performance Sodium Metal Batteries

An efficient method for the synthesis of a self-supporting carbon framework (denoted Gra-GC-MoSe2) is proposed with a triple-gradient structure-in sodiophilic sites, pore volume, and electrical conductivity-which facilitates the highly efficient regulation of Na deposition. In situ and ex situ measurements, together with theoretical calculations, reveal that the gradient distribution of Se heteroatoms in MoSe2, and its derivatives tailor the sodiophilicity, while the gradient distribution of porous nanostructures homogenizes the Na+ diffusion. Therefore, Na deposition occurs from the bottom to the top of the Gra-GC-MoSe2 framework without dendrite formation. In addition, the gradient in electrical conductivity ensures the stripping process does not lead to dead Na. As a result, a Gra-GC-MoSe2 modified Na anode (Na@Gra-GC-MoSe2) shows impressive cycling stability with a high average Coulombic efficiency in an asymmetric cell. In symmetric cells, it also exhibits a long cycling life of 2000 h with a low polarization voltage and works stably even under a large capacity of 10 mAh cm-2. Moreover, a Na@Gra-GC-MoSe2|| Na3V2(PO4)3 full cell delivers a high energy density with an excellent cycling performance.

A Critical Review on Room-Temperature Sodium-Sulfur Batteries: From Research Advances to Practical Perspectives

Room-temperature sodium-sulfur (RT-Na/S) batteries are promising alternatives for next-generation energy storage systems with high energy density and high power density. However, some notorious issues are hampering the practical application of RT-Na/S batteries. Besides, the working mechanism of RT-Na/S batteries under practical conditions such as high sulfur loading, lean electrolyte, and low capacity ratio between the negative and positive electrode (N/P ratio), is of essential importance for practical applications, yet the significance of these parameters has long been disregarded. Herein, it is comprehensively reviewed recent advances on Na metal anode, S cathode, electrolyte, and separator engineering for RT-Na/S batteries. The discrepancies between laboratory research and practical conditions are elaborately discussed, endeavors toward practical applications are highlighted, and suggestions for the practical values of the crucial parameters are rationally proposed. Furthermore, an empirical equation to estimate the actual energy density of RT-Na/S pouch cells under practical conditions is rationally proposed for the first time, making it possible to evaluate the gravimetric energy density of the cells under practical conditions. This review aims to reemphasize the vital importance of the crucial parameters for RT-Na/S batteries to bridge the gaps between laboratory research and practical applications.

Spatially Confined in Situ Formed Sodiophilic-Conductive Network for High-Performance Sodium Metal Batteries

The sodium (Na) metal anode encounters issues such as volume expansion and dendrite growth during cycling. Herein, a novel three-dimensional flexible composite Na metal anode was constructed through the conversion-alloying reaction between Na and ultrafine Sb2S3 nanoparticles encapsulated within the electrospun carbon nanofibers (Sb2S3@CNFs). The formed sodiophilic Na3Sb sites and the high Na+-conducting Na2S matrix, coupled with CNFs, establish a spatially confined "sodiophilic-conductive" network, which effectively reduces the Na nucleation barrier, improves the Na+ diffusion kinetics, and suppresses the volume expansion, thereby inhibiting the Na dendrite growth. Consequently, the Na/Sb2S3@CNFs electrode exhibits a high Coulombic efficiency (99.94%), exceptional lifespan (up to 2800 h) at high current densities (up to 5 mA cm-2), and high areal capacities (up to 5 mAh cm-2) in symmetric cells. The coin-type full cells assembled with a Na3V2(PO4)3/C cathode demonstrate significant enhancement in electrochemical performance. The flexible pouch cell achieves an excellent energy density of 301 Wh kg-1.

Enhanced TiO2/SiCx Active Layer Formed In Situ on Coal Gangue/Ti3C2 MXene Electrocatalyst as Catalytic Integrated Units for Efficient Li-O2 Batteries

The pursuit of efficient cathode catalysts to improve cycle stability at ultra-high rates plays an important role in boosting the practical utilization of Li-O2 batteries. Featured as industrial solid waste, coal gangue with rich electrochemical active components could be a promising candidate for electrocatalysts. Here, a coal gangue/Ti3C2 MXene hybrid with a TiO2/SiCx active layer is synthesized and applied as a cathode catalyst in Li-O2 batteries. The coal gangue/Ti3C2 MXene hybrid has a tailored amorphous/crystalline heterostructure, enhanced active TiO2 termination, and a stable SiCx protective layer; thereby, it achieved an excellent rate stability. The Li-O2 battery, assembled with a coal gangue/Ti3C2 MXene cathode catalyst, was found to obtain a competitive full discharge capacity of 3959 mAh g-1 and a considerable long-term endurance of 180 h (up to 175 cycles), with a stable voltage polarization of 1.72 V at 2500 mA g-1. Comprehensive characterization measurements (SEM, TEM, XPS, etc.) were applied; an in-depth analysis was conducted to reveal the critical role of TiO2/SiCX active units in regulating the micro-chemical constitution and the enhanced synergistic effect between coal gangue and Ti3C2 MXene. This work could provide considerable insights into the rational design of catalysts derived from solid waste gangue for high-rate Li-O2 batteries.

Ultrahigh areal capacity and long cycling stability of sodium metal anodes boosted using a 3D-printed sodiophilic MXene/rGO microlattice aerogel

Sodium metal has emerged as a highly promising anode material for sodium-based batteries, owing to its intrinsic advantages, including its high theoretical capacity, low working plateau and low cost. However, the uncontrolled formation of sodium dendrites accompanied by unrestricted volume expansion severely limits its application. To tackle these issues, we propose an approach to address these issues by adopting a three-dimensional (3D) structure of Ti3C2Tx/reduced graphene oxide (Ti3C2Tx/rGO) constructed by a direct-ink writing (DIW) 3D printing technique as the Na metal anode host electrode. The combination of the 3D-printed rGO skeleton offering artificial porous structures and the incorporation of sodiophilic Ti3C2Tx nanosheets provides abundant nucleation sites and promotes uniform sodium metal deposition. This specially designed architecture significantly enhances the Na metal cycling stability by effectively inhibiting dendrite formation. The experimental results show that the designed Ti3C2Tx/rGO electrode can achieve a high coulombic efficiency (CE) of 99.91% after 1800 cycles (3600 h) at 2 mA cm-2 with 2 mA h cm-2. Notably, the adopted electrodes exhibit a long life span of more than 1400 h with a high CE over 99.93% when measured with an ultra-high capacity of 50 mA h cm-2 at 5 mA cm-2. Furthermore, a 3D-printed full cell consisting of a Na@Ti3C2Tx/rGO anode and a 3D-printed Na3V2(PO4)3C-rGO (NVP@C-rGO) cathode was successfully demonstrated. This 3D-printed cell could provide a notable capacity of 85.3 mA h g-1 at 100 mA g-1 after 500 cycles. The exceptional electrochemical performance achieved by the 3D-printed full cell paves the way for the development of practical sodium metal anodes.

Fluorinated porous frameworks enable robust anode-less sodium metal batteries

Sodium metal batteries hold great promise for energy-dense and low-cost energy storage technology but are severely impeded by catastrophic dendrite issue. State-of-the-art strategies including sodiophilic seeding/hosting interphase design manifest great success on dendrite suppression, while neglecting unavoidable interphase-depleted Na+ before plating, which poses excessive Na use, sacrificed output voltage and ultimately reduced energy density. We here demonstrate that elaborate-designed fluorinated porous framework could simultaneously realize superior sodiophilicity yet negligible interphase-consumed Na+ for dendrite-free and durable Na batteries. As elucidated by physicochemical and theoretical characterizations, well-defined fluorinated edges on porous channels are responsible for both high affinities ensuring uniform deposition and low reactivity rendering superior Na+ utilization for plating. Accordingly, synergistic performance enhancement is achieved with stable 400 cycles and superior plateau to sloping capacity ratio in anode-free batteries. Proof-of-concept pouch cells deliver an energy density of 325 Watt-hours per kilogram and robust 300 cycles under anode-less condition, opening an avenue with great extendibility for the practical deployment of metal batteries.

A Universal Strategy Based on Bridging Microstructure Engineering and Local Electronic Structure Manipulation for High-Performance Sodium Layered Oxide Cathodes

Due to their high capacity and sufficient Na+ storage, O3-NaNi0.5Mn0.5O2 has attracted much attention as a viable cathode material for sodium-ion batteries (SIBs). However, the challenges of complicated irreversible multiphase transitions, poor structural stability, low operating voltage, and an unstable oxygen redox reaction still limit its practical application. Herein, using O3-NaNi0.5Mn0.5-xSnxO2 cathode materials as the research model, a universal strategy based on bridging microstructure engineering and local electronic structure manipulation is proposed. The strategy can modulate the physical and chemical properties of electrode materials, so as to restrain the unfavorable and irreversible multiphase transformation, improve structural stability, manipulate redox potential, and stabilize the anion redox reaction. The effect of Sn substitution on the intrinsic local electronic structure of the material is articulated by density functional theory calculations. Meanwhile, the universal strategy is also validated by Ti substitution, which could be further extrapolated to other systems and guide the design of cathode materials in the field of SIBs.