Highly Active Photocatalyst of Cu2O/TiO2 Octahedron for Hydrogen Generation

Tailoring Interfacial Physicochemical Properties in Cu2O-TiO2@rGO Heterojunction: Insights from EXAFS and Electron Trap Distribution Analysis

In this study, a solution-based synthesis technique was utilized to produce Cu2O nanoparticles (NPs) on TiO2 nanofibers (TNF), which were then subsequently coated with reduced graphene oxide (rGO) nanosheets. In the absence of any cocatalyst, CTNF@rGO-3% composite displayed an ideal photocatalytic H2 evolution rate of 96 μmol g-1 h-1 under visible light irradiation, this was 10 times higher than that of pure TNF. At 420 nm, the apparent quantum efficiency of this composite reached a maximum of 7.18%. Kelvin probe force microscopy demonstrated the formation of an interfacial electric field that was oriented from CTNF to rGO and served as the driving force for interfacial electron transfer. The successful establishment of an intimate interface between CTNF@rGO facilitated the efficient transfer of charges and suppressed the rate of recombination of photogenerated electron-hole pairs, leading to a substantial enhancement in photocatalytic performance. X-ray photoelectron spectroscopy, photoluminescence spectra, and electrochemical characterization provide further confirmation that formation of a heterojunction between CTNF@rGO leads to an extension in the lifetimes of the photogenerated charge carriers. The experimental evidence suggests that a p-n heterojunction is the mechanism responsible for the significant photocatalytic activity observed in the CTNF@rGO composite during H2 evolution.

Enhanced photoactive performance of three-layer structured Ag/Cu2O/TiO2 composites with tunable crystal microstructures

Ag particle-decorated Cu2O/TiO2 composite films effectively photodegrade MO solution under irradiation.

Composite CdS/TiO2 Powders for the Selective Reduction of 4-Nitrobenzaldehyde by Visible Light: Relation between Preparation, Morphology and Photocatalytic Activity

A series of composite CdS/TiO2 powders was obtained by nucleation of TiO2 on CdS nanoseeds. This combination presents the appropriate band edge position for photocatalytic redox reactions: visible light irradiation of CdS allows the injection of electrons into dark TiO2, increasing the lifetimes of separated charges. The electrons have been used for the quantitative photoreduction of 4-nitrobenzaldehyde to 4-aminobenzaldehyde, whose formation was pointed out by 1H NMR and ESI-MS positive ion mode. Concomitant sacrificial oxidation of 2-propanol, which was also the proton source, occurred. The use of characterization techniques (XRD, N2 adsorption-desorption) evidenced the principal factors driving the photocatalytic reaction: the nanometric size of anatase crystalline domains, the presence of dispersed CdS to form an extended active junction CdS/anatase, and the presence of mesopores as nanoreactors. The result is an efficient photocatalytic system that uses visible light. In addition, the presence of TiO2 in combination with CdS improves the stability of the photoactive material, enabling its recyclability.

MII (M = Mn, Fe, Co, Ni and Cu) complexes with a chromone-derived neutral ligand: synthesis, structural characterization, photocatalytic and mycobacterial activity studies

This work provides the coordination chemistry of the resulting compound of 2-(2-furyl)-3-hydroxychromone and nicotinoyl chloride with first row transition metal ions. Good performance in H2 evolution was shown by the copper-containing photocatalyst.

Crystal facet and phase engineering for advanced water splitting

This review covers the principles and recent advances in facet and phase engineering of catalysts for photocatalytic, photoelectrochemical, and electrochemical water splitting. It suggests the basis of catalyst design for advanced water splitting.

Photocatalytic Reduction of CO2 to Methanol by Cu2O/TiO2 Heterojunctions

The conversion of CO2 to low-carbon fuels using solar energy is considered an economically attractive and environmentally friendly route. The development of novel catalysts and the use of solar energy via photocatalysis are key to achieving the goal of chemically reducing CO2 under mild conditions. TiO2 is not very effective for the photocatalytic reduction of CO2 to low-carbon chemicals such as methanol (CH3OH). Thus, in this work, novel Cu2O/TiO2 heterojunctions that can effectively separate photogenerated electrons and holes were prepared for photocatalytic CO2-to-CH3OH. More visible light-active Cu2O in the Cu2O/TiO2 heterojunctions favors the formation of methanol under visible light irradiation. On the other hand, under UV-Vis irradiation for 6 h, the CH3OH yielded from the photocatalytic CO2-to-CH3OH by the Cu2O/TiO2 heterojunctions is 21.0–70.6 µmol/g-catalyst. In contrast, the yield of CH3OH decreases with an increase in the Cu2O fraction in the Cu2O/TiO2 heterojunctions. It seems that excess Cu2O in Cu2O/TiO2 heterojunctions may lead to less UV light exposure for the photocatalysts, and may decrease the conversion efficiency of CO2 to CH3OH.

One-Step Hydrothermal Synthesis of Precious Metal-Doped Titanium Dioxide-Graphene Oxide Composites for Photocatalytic Conversion of CO2 to Ethanol

We utilized a one-step hydrothermal process for the synthesis of precious metal-doped titanium dioxide (TiO₂)/graphene oxide (GO) composites. The metal-doped TiO₂/GO composites, including silver-TiO₂/GO (Ag-TiO₂/GO), palladium-TiO₂/GO (Pd-TiO₂/GO), and copper-TiO₂/GO (Cu-TiO₂/GO), were synthesized by mixing a metal precursor, titanium butoxide, and graphene oxide in a water-ethanol mixture in an autoclave hydrothermal reactor. The photocatalytic performance of the composites was tested in the photoreduction of carbon dioxide (CO₂) to ethanol. Ag-TiO₂/GO, Pd-TiO₂/GO, and Cu-TiO₂/GO exhibited an ethanol production rate of 109, 125, and 233 μmol/g_cat h, respectively. The outstanding performances of Cu-TiO₂/GO can be attributed to a combined effect of key parameters, including optical band gap, crystallite size, and BET surface area.

Copper Oxide-Based Photocatalysts and Photocathodes: Fundamentals and Recent Advances

This work aims at reviewing the most impactful results obtained on the development of Cu-based photocathodes. The need of a sustainable exploitation of renewable energy sources and the parallel request of reducing pollutant emissions in airborne streams and in waters call for new technologies based on the use of efficient, abundant, low-toxicity and low-cost materials. Photoelectrochemical devices that adopts abundant element-based photoelectrodes might respond to these requests being an enabling technology for the direct use of sunlight to the production of energy fuels form water electrolysis (H2) and CO2 reduction (to alcohols, light hydrocarbons), as well as for the degradation of pollutants. This review analyses the physical chemical properties of Cu2O (and CuO) and the possible strategies to tune them (doping, lattice strain). Combining Cu with other elements in multinary oxides or in composite photoelectrodes is also discussed in detail. Finally, a short overview on the possible applications of these materials is presented.

Simultaneous Tuning Band Gaps of Cu2 O and TiO2 to Form S-Scheme Hetero-Photocatalyst

Photocatalytic Z or S scheme merits higher redox potentials and faster charge separation. However, heterostructure photocatalysts with band gaps of bulk materials often have a type I band structure leading to poor photocatalytic activity. In view of this, we report simultaneous tuning of band gaps of Cu₂ O and TiO₂ , where quantum dot Cu₂ O nanoparticles were formed on doped TiO₂ with Ti³⁺ . The reduced size of Cu₂ O made its conduction band more negative, whereas the introduction of Ti³⁺ made the absorption edge red shift to the visible light region. The as-formed heterostructure enabled an S-Scheme mechanism with remarkable activity and stability for visible light photodegradation of 4-chlorophenol (4-CP). The as-obtained photocatalysts' activity demonstrated ca. 510-fold increase as compared to individual ones and a mechanical blend. The as-obtained photocatalysts maintained over 80 % for 5 cycles and 2 months exposure to O₂ did not decrease the degradation rate. ESR characterization and scavenger experiments proved the S-Scheme mechanism.

Synthesis and Photocatalytic Activity of TiO2/CdS Nanocomposites with Co-Exposed Anatase Highly Reactive Facets

In this work, TiO2/CdS nanocomposites with co-exposed {101}/[111]-facets (NH4F-TiO2/CdS), {101}/{010} facets (FMA-TiO2/CdS), and {101}/{010}/[111]-facets (HF-TiO2/CdS and Urea-TiO2/CdS) were successfully synthesized through a one-pot solvothermal method by using [Ti4O9]2- colloidal solution containing CdS crystals as the precursor. The crystal structure, morphology, specific surface area, pore size distribution, separation, and recombination of photogenerated electrons/holes of the TiO2/CdS nanocomposites were characterized. The photocatalytic activity and cycling performance of the TiO2/CdS nanocomposites were also investigated. The results showed that as-prepared FMA-TiO2/CdS with co-exposed {101}/{010} facets exhibited the highest photocatalytic activity in the process of photocatalytic degradation of methyl orange (MO), and its degradation efficiency was 88.4%. The rate constants of FMA-TiO2/CdS was 0.0167 min-1, which was 55.7, 4.0, 3.7, 3.5, 3.3, and 1.9 times of No catalyst, CdS, HF-TiO2/CdS, NH4F-TiO2/CdS, CM-TiO2, Urea-TiO2/CdS, respectively. The highest photocatalytic activity of FMA-TiO2/CdS could be attributed to the synergistic effects of the largest surface energy, co-exposed {101}/{010} facets, the lowest photoluminescence intensity, lower charge-transfer resistance, and a higher charge-transfer efficiency.

Effect of Cu2O Substrate on Photoinduced Hydrophilicity of TiO2 and ZnO Nanocoatings

The effect of a Cu₂O substrate on the photoinduced alteration of the hydrophilicity of TiO₂ and ZnO surfaces was studied. It was demonstrated that the formation of heterostructures Cu₂O/TiO₂ and Cu₂O/ZnO strongly changed the direction of the photoinduced alteration of surface hydrophilicity: while both TiO₂ and ZnO demonstrate surface transition to superhydrophilic state under UV irradiation and no significant alteration of the surface hydrophilicity under visible light irradiation, the formation of Cu₂O/TiO₂ and Cu₂O/ZnO heterostructures resulted in photoinduced decay of the surface hydrophilicity caused by both UV and visible light irradiation. All observed photoinduced changes of the surface hydrophilicity were compared and analyzed in terms of photoinduced alteration of the surface free energy and its polar and dispersive components. Alteration of the photoinduced hydrophilic behavior of TiO₂ and ZnO surfaces caused by formation of the corresponding heterostructures with Cu₂O are explained within the mechanism of electron transfer and increasing of the electron concentration on the TiO₂ and ZnO surfaces.

Elucidating the Factors Affecting Hydrogen Production Activity Using a CdS/TiO2 Type-II Composite Photocatalyst

CdS/TiO2 is a composite photocatalyst that has been studied over many years and in which electron transfer from CdS to TiO2 is believed to lead to high photocatalytic activity. However, most reports on improved activity involve hydrogen production in the presence of a sulfide reducing agent. In this study, we comprehensively examined the effects of electron transfer, hydrogen overvoltage, substrate adsorption, and the cocatalyst from relationships between hydrogen production ability and the total number of trapped electrons in the presence of various reducing agents. As a result, we clarified that the electron transfer between CdS and TiO2 does not necessarily lead to high activity. We showed that the composite photocatalyst needs to be designed for the intended purpose and that evaluating the hydrogen production ability using sacrificial reagents provides insufficient information for use in an actual environment.

Wastewater Contaminated with Hydrazine as Scavenger Agent for Hydrogen Production by Cu/Ti Nanostructures

Cu/Ti photocatalysts were prepared by the sol-gel process with different copper loadings (1.0, 2.5, and 5.0 wt.%) and then thermally treated at several calcination temperatures from 400 to 600 °C. The materials were characterized by X-ray diffraction (XRD), N2 physisorption, Scanning Electronic Microscopy with Energy Dispersive X-ray Spectroscopy (SEM-EDS), Ultraviolet-visible-Diffuse Reflection Spectroscopy, Ultraviolet-visible spectroscopy as a function of the temperature, (Temperature Programmed Reduction) TPR-chemisorption, XPS (X-ray Photoelectron Spectroscopy) and OH determination through DRIFTS (Diffuse reflectance infrared Fourier transform spectroscopy). The Cu/Ti photocatalysts were evaluated for the photocatalytic production of hydrogen using hydrazine as scavenging agent. Moreover, a detailed study of the Cu1+/Cu2+ ratio and the corresponding formation of copper oxide was carried out to understand the correlation between the copper species and the photocatalytic activity. Simultaneously, the OH groups on the TiO2 surface also show insights into the behavior of these materials during the photocatalytic reaction. Despite the low hydrazine concentration (20 mM), the 1.0 (wt.%) Cu/Ti 500 photocatalyst enhanced the hydrogen production three and two times more than photolysis and bare TiO2, respectively. The 1.0 Cu/Ti 500 photocatalyst displayed outstanding stability for at least three continuous cycles of 8 h each, preserving the hydrogen production. The novel ability shown in this work represents an alternative to reduce the hydrazine residues in wastewater to transform it into a hydrogen-producing energy source and must be extended to other reductive pollutants found in wastewater.

MOF-derived porous TiO2 decorated with n-type Cu2O for efficient photocatalytic H2 evolution

Type-I Cu2O/TiO2 with a porous structure has excellent photocatalytic activity for hydrogen production because of the effectively separated electron–hole pairs.

Enhanced photocatalytic degradation of tetracycline by constructing a controllable Cu2O–TiO2 heterojunction with specific crystal facets

Type II heterojunction of 100Cu2O–TiO2 exhibits enhanced photodegradation rate of TC at the sacrifice of absolute decomposition, while 111Cu2O–TiO2 Z-scheme heterojunction displays simultaneous increased degradation rate and profound decomposition.

Ultrahigh electrocatalytic activity with trace amounts of platinum loadings on free-standing mesoporous titanium nitride nanotube arrays for hydrogen evolution reactions

Minimizing Pt loadings on electrocatalysts for hydrogen evolution reactions (HERs) is essential for their commercial applications. Herein, free-standing mesoporous titanium nitride nanotube arrays (TiN NTAs) were fabricated to serve as a substrate for Pt loadings in trace amounts. TiN NTAs were prepared by thermal treatment of anodic TiO2 NTAs at 750 °C for 3 h in a NH3 atmosphere. The uniform TiN NTAs showed an inner diameter of ∼80 nm and a length of ∼7 μm, with many mesoporous holes ranging from 5 to 10 nm in diameter on the nanotube walls. Pt species dissolved from the Pt counter electrode in electrochemical cycling were redeposited on the mesoporous TiN NTAs to produce Pt-TiN NTAs with an ultra-low Pt loading of 8.3 μg cm-2. Pt-TiN NTAs exhibited 15-fold higher mass activity towards HER than the benchmark 20 wt% Pt/C in acidic media, with an overpotential of 71 mV vs. RHE at a current density of 10 mA cm-2, a Tafel slope value of 46.4 mV dec-1 and excellent stability. The performance of Pt-TiN NTAs is also much better than that of Pt species deposited on non-mesoporous nanotube arrays due to the shortcuts originating from the mesoporous holes on the nanotube walls for electron and mass transfer.

Simple synthesis of hierarchically porous Sn/TiO2/graphitic carbon microspheres for CO2 reduction with H2O under simulated solar irradiation

A simple colloidal crystal template method was used to prepare Sn/TiO₂/graphite carbon microsphere composites (xSn/TiO₂/GCM, x = 2.0, 1.0, 0.2, 0.5) with porous layers. Then, the composites were represented using X-ray diffraction, energy dispersive spectrometry, scanning electron microscopy, transmission electron microscopy, and nitrogen physical adsorption/desorption. Meanwhile, the photocatalytic activities in CO₂ reduction were studied under simulation of visible light exposure. It was confirmed that the Sn/TiO₂/GCM composites had layered porosity, graphitized carbon matrix, and high metal compound content, and their morphology was greatly affected by the acetone amount. The outputs of CO and CH₄ coming into the photocatalytic CO₂ reduction reaction of Sn/TiO₂/GCM were 619.46 and 14.46 μmol g^-1, respectively. Among the two products, the highest production rate observed in 0.5Sn/TiO₂/GCM. Because of these factors, the layered porous Sn/TiO₂/GCM composites have good photocatalytic performance under simulated visible light irradiation and have unique composition and structure characteristics, which give broad application prospects in electrode materials, catalysts, and adsorbents. Graphical abstract.

Enhanced Hydrogen Production from Ethanol Photoreforming by Site-Specific Deposition of Au on Cu2O/TiO2 p-n Junction

Hydrogen production by photoreforming of biomass-derived ethanol is a renewable way of obtaining clean fuel. We developed a site-specific deposition strategy to construct supported Au catalysts by rationally constructing Ti3+ defects inTiO2 nanorods and Cu2O-TiO2 p-n junction across the interface of two components. The Au nanoparticles (~2.5 nm) were selectively anchored onto either TiO2 nanorods (Au@TiO2/Cu2O) or Cu2O nanocubes (Au@Cu2O/TiO2) or both TiO2 and Cu2O (Au@TiO2/Cu2O@Au) with the same Au loading. The electronic structure of supported Au species was changed by forming Au@TiO2 interface due to the adjacent Ti3+ defects and the associated oxygen vacancies while unchanged in Au@Cu2O/TiO2 catalyst. The p-n junction of TiO2/Cu2O promoted charge separation and transfer across the junction. During ethanol photoreforming, Au@TiO2/Cu2O catalyst possessing both the Au@TiO2 interface and the p-n junction showed the highest H2 production rate of 8548 μmol gcat−1 h−1 under simulated solar light, apparently superior to both Au@TiO2 and Au@Cu2O/TiO2 catalyst. The acetaldehyde was produced in liquid phase at an almost stoichiometric rate, and C−C cleavage of ethanol molecules to form CH4 or CO2 was greatly inhibited. Extensive spectroscopic results support the claim that Au adjacent to surface Ti3+ defects could be active sites for H2 production and p-n junction of TiO2/Cu2O facilitates photo-generated charge transfer and further dehydrogenation of ethanol to acetaldehyde during the photoreforming.

Visible-Light Active Titanium Dioxide Nanomaterials with Bactericidal Properties

This article provides an overview of current research into the development, synthesis, photocatalytic bacterial activity, biocompatibility and cytotoxic properties of various visible-light active titanium dioxide (TiO2) nanoparticles (NPs) and their nanocomposites. To achieve antibacterial inactivation under visible light, TiO2 NPs are doped with metal and non-metal elements, modified with carbonaceous nanomaterials, and coupled with other metal oxide semiconductors. Transition metals introduce a localized d-electron state just below the conduction band of TiO2 NPs, thereby narrowing the bandgap and causing a red shift of the optical absorption edge into the visible region. Silver nanoparticles of doped TiO2 NPs experience surface plasmon resonance under visible light excitation, leading to the injection of hot electrons into the conduction band of TiO2 NPs to generate reactive oxygen species (ROS) for bacterial killing. The modification of TiO2 NPs with carbon nanotubes and graphene sheets also achieve the efficient creation of ROS under visible light irradiation. Furthermore, titanium-based alloy implants in orthopedics with enhanced antibacterial activity and biocompatibility can be achieved by forming a surface layer of Ag-doped titania nanotubes. By incorporating TiO2 NPs and Cu-doped TiO2 NPs into chitosan or the textile matrix, the resulting polymer nanocomposites exhibit excellent antimicrobial properties that can have applications as fruit/food wrapping films, self-cleaning fabrics, medical scaffolds and wound dressings. Considering the possible use of visible-light active TiO2 nanomaterials for various applications, their toxicity impact on the environment and public health is also addressed.

g-C3N4/TiO2 composite microspheres: in situ growth and high visible light catalytic activity

The g-C₃N₄/TiO₂ heterojunction, possessing a 3D flower-like self-assembled morphology, realizing excellent visible-light photocatalytic properties, is a photocatalyst for wastewater treatment or a photoanode for photoelectrochemical water splitting.