TiO2/(K,Na)NbO3 Nanocomposite for Boosting Humidity-Sensing Performances

Highly Sensitive Gas Sensor for Detection of Air Decomposition Pollutant (CO, NOx): Popular Metal Oxide (ZnO, TiO2)-Doped MoS2 Surface

When partial discharges occur in air-insulated equipment, the air decomposes to produce a variety of contamination products, resulting in a reduction in the insulation performance of the insulated equipment. By monitoring the concentration of typical decomposition products (CO, NO, and NO2) within the insulated equipment, potential insulation faults can be diagnosed. MoS2 has shown promising applications as a gas-sensitive semiconductor material, and doping metal oxides can improve the gas-sensitive properties of the material. Therefore, in this work, MoS2 has been doped using the popular metal oxides (ZnO, TiO2) of the day, and its gas-sensitive properties to the typical decomposition products of air have been analyzed and compared using density functional theory (DFT) calculations. The stability of the doped system was investigated using molecular dynamics methods. The related adsorption mechanism was analyzed by adsorption configuration, energy band structure, density of states (DOS) analysis, total electron density (TED) analysis, and differential charge density (DCD) analysis. Finally, the practical application of related sensing performance is evaluated. The results show that the doping of metal oxide nanoparticles greatly improves the conductivity, gas sensitivity, and adsorption selectivity of MoS2 monolayer to air decomposition products. The sensing response of ZnO-MoS2 for CO at room temperature (25 °C) reaches 161.86 with a good recovery time (0.046 s). TiO2-MoS2 sensing response to NO2 reaches 3.5 × 106 at 25 °C with a good recovery time (0.108 s). This study theoretically solves the industrial challenge of recycling sensing materials and provides theoretical value for the application of resistive chemical sensors in air-insulated equipment.

Boosting the Sensitivity and Hysteresis of a Gel Polymer Electrolyte by Embedding SiO2 Nanoparticles and PVP for Humidity Applications

Enhancing sensitivity and hysteresis in capacitance humidity sensors is vital for precise, reliable, and consistent humidity control. This study explores this concern by incorporating polyvinylpyrrolidone (PVP) and SiO2 nanoparticles into a polyvinyl alcohol (PVA)-based ionic liquid gel polymer electrolyte (ILGPE), studying two capacitor types: ILGPE and SiO2 composite ILGPE (CILGPE) capacitors. These novel electrolytes use ammonium acetate as a plasticiser, 1-butyl-3-methylimidazolium bromide as an ionic liquid, SiO2 nanoparticles as a composite, and PVA and PVP as host polymers. Capacitors were characterised and modelled using impedance spectroscopy (IS), providing an electrophysical insight into their working principle. Sensitivity and hysteresis were evaluated within a 20-90% relative humidity (RH) range at 25 °C. The SiO2 CILGPE capacitor with PVP presented superior sensitivity and hysteresis, revealing the beneficial combination of SiO2 nanoparticles and PVP. These benefits are due to the creation of pathways that facilitate water molecule diffusion and crystallinity reduction in PVA-ILGPE. In particular, at 10 kHz, it demonstrates a calibrated capacitance sensitivity of 2660 pF/%RH and a hysteresis of 3.28 %RH. This optimised capacitor outperforms some previous humidity capacitive sensors in sensitivity while exhibiting low hysteresis.

An All-Printed, Fast-Response Flexible Humidity Sensor Based on Hexagonal-WO3 Nanowires for Multifunctional Applications

The utilization of printing techniques for the development of high-performance humidity sensors holds immense significance for various applications in the fields of the Internet of Things, agriculture, human healthcare, and storage environments. However, the long response time and low sensitivity of current printed humidity sensors limit their practical applications. Herein, a series of high-sensing-performance flexible resistive-type humidity sensors is fabricated by the screen-printing method, and hexagonal tungsten oxide (h-WO3 ) is employed as the humidity-sensing material due to its low cost, strong chemical adsorption ability, and excellent humidity-sensing ability. The as-prepared printed sensors exhibit high sensitivity, good repeatability, outstanding flexibility, low hysteresis, and fast response (1.5 s) in a wide relative humidity (RH) range (11-95% RH). Furthermore, the sensitivity of humidity sensors can be easily adjusted by altering the manufacturing parameters of the sensing layer and interdigital electrode to meet the diverse requirements of specific applications. The printed flexible humidity sensors possess immense potential in various applications, including wearable devices, non-contact measurements, and packaging opening state monitoring.

Humidity Sensing Properties of (In+Nb) Doped HfO2 Ceramics

(In+Nb) co-doped HfO₂ ceramics, Hf_1-x(In_0.5Nb_0.5)_xO₂ (x = 0, 0.005, 0.05, and 0.1), were prepared via a solid-state reaction method. Dielectric measurements reveal that the environmental moisture has an obvious influence on the dielectric properties of the samples. The best humidity response was found in a sample with the doping level of x = 0.005. This sample was therefore selected as a model sample to further investigate its humidity properties. In doing so, nanosized particles of Hf_0.995(In_0.5Nb_0.5)_0.005O₂ were fabricated via a hydrothermal method and the humidity sensing properties of this material were studied in the relative humidity range of 11–94% based on impedance sensor. Our results show that the material exhibits a large impedance change of nearly four orders of magnitude over the tested humidity range. It was argued that the humidity-sensing properties were related to the defects created by doping, which improves the adsorption capacity for water molecules.

Collaborative Enhancement of Humidity Sensing Performance by KCl-Doped CuO/SnO2 p-n Heterostructures for Monitoring Human Activities

In this study, a high-performance humidity sensor based on KCl-doped CuO/SnO₂ p-n heterostructures was fabricated by a ball milling-roasting method. The morphology and nanostructure of the fabricated KCl-CuO/SnO₂ composite were characterized by scanning electron microscopy, X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, and nitrogen sorption analysis. The results showed that the humidity sensor had a high sensitivity of 194 kΩ/%RH, short response and recovery times of 1.0 and 1.5 s, a low hysteresis value, and good repeatability. The energy band structure and complex impedance spectrum of the KCl-CuO/SnO₂ composite indicated that the excellent humidity sensing performance originated from the ionic conductivity of KCl, the formation of heterojunctions, the change in the Schottky barrier height, and the depletion of electronic depletion layers. The KCl-CuO/SnO₂ sensor has great potential in respiratory monitoring, noncontact sensing of finger moisture, and environmental monitoring.

Photocatalytic and Antibacterial Activity of CoFe2O4 Nanoparticles from Hibiscus rosa-sinensis Plant Extract

Biogenic CoFe₂O₄ nanoparticles were prepared by co-precipitation and Hibiscus rosa sinensis plant leaf was used as a bio-reductant of the nanoparticle productions. The biosynthesized CoFe₂O₄ nanoparticles were characterized by XRD, FTIR, UV, VSM, and SEM via EDX analysis. The cubic phase of biosynthesized CoFe₂O₄ nanoparticles and their crystallite size was determined by XRD. The Co-Fe-O bonding and cation displacement was confirmed by FTIR spectroscopy. The presence of spherically-shaped biosynthesized CoFe₂O₄ nanoparticles and their material were confirmed by SEM and TEM via EDX. The super-paramagnetic behaviour of the biosynthesized CoFe₂O₄ nanoparticles and magnetic pulse was established by VSM analysis. Organic and bacterial pollutants were eradicated using the biosynthesized CoFe₂O₄ nanoparticles. The spinel ferrite biosynthesized CoFe₂O₄ nanoparticles generate radical and superoxide ions, which degrade toxic organic and bacterial pollutants in the environment.

An Improved Humidity Sensor with GO-Mn-Doped ZnO Nanocomposite and Dimensional Orchestration of Comb Electrode for Effective Bulk Manufacturing

The measurement and control of humidity is a major challenge that affects the sensing properties of sensors used in high-precision equipment manufacturing industries. Graphene Oxide(GO)-based materials have been extensively explored in humidity sensing applications because of their high surface area and functional groups. However, there is a lack of effective bulk-manufacturing processes for the synthesis of 2D-based nanocomposites with comb electrodes. Moreover, water intercalation within the layers of 2D materials increases recovery time. This work demonstrates the enhanced sensing characteristics of a capacitive/resistive GO-MnZnO nanocomposite humidity sensor produced using a cost-effective single-pot synthesis process. The in-plane sensing layer consistently improves sensitivity and reduces response time for a wide range of relative humidity measurements (10% to 90%). Interdigitated gold electrodes with varying numbers of fingers and spacing were fabricated using photolithography on a Si/SiO₂ for a consistent sensor device platform. The choice of nanomaterials, dimension of the sensor, and fabrication method influence the performance of the humidity sensor in a controlled environment. GO nanocomposites show significant improvement in response time (82.67 times greater at 40% RH) and sensitivity (95.7 times more at 60% RH). The response time of 4.5 s and recovery time of 21 s was significantly better for a wider range of relative humidity compared to the reduced GO-sensing layer and ZnMnO. An optimized 6 mm × 3 mm dimension sensor with a 28-fingers comb was fabricated with a metal-etching process. This is one of the most effective methods for bulk manufacturing. The performance of the sensing layer is comparable to established sensing nanomaterials that are currently used in humidity sensors, and hence can be extended for optimal bulk manufacturing with minimum electrochemical treatments.

High Humidity Response of Sol-Gel-Synthesized BiFeO3 Ferroelectric Film

In this work, a BiFeO₃ film is prepared via a facile sol–gel method, and the effects of the relative humidity (RH) on the BiFeO₃ film in terms of capacitance, impedance and current–voltage (I–V) are explored. The capacitance of the BiFeO₃ film increased from 25 to 1410 pF with the increase of RH from 30% to 90%. In particular, the impedance varied by more than two orders of magnitude as RH varied between 30% and 90% at 10 Hz, indicating a good hysteresis and response time. The mechanism underlying humidity sensitivity was analyzed by complex impedance spectroscopy. The adsorption of water molecules played key roles at low and high humidity, extending the potential application of ferroelectric BiFeO₃ films in humidity-sensitive devices.

A Three-Dimensional-Printed Recyclable, Flexible, and Wearable Device for Visualized UV, Temperature, and Sweat pH Sensing

Wearable devices are now recognized as a powerful tool to collect physiological and environmental information in a smart, noninvasive, and real-time manner. Despite the rapid progress of wearable devices especially wearable electronic devices, there are still several challenges that limit their further development, for example, a complicated electrical signal acquisition and processing process to eliminate the interference from the surrounding signals, bulky power supply, inevitable e-waste, and environmental pollution. Herein, we report a 3D-printed recyclable, flexible, and wearable device for visualized UV, temperature, and sweat pH sensing. Compared with wearable electronic devices, our visualized wearable device senses environmental (UV light, ambient temperature), biophysical (skin temperature), and biochemical (sweat pH) signals via stimuli-responsive color change, which does not require complicated electronic circuit design/assembly, time-consuming data processing and additional power source. In addition, this visualized wearable device is fabricated via a 3D support bath printing technology by printing UV-, temperature-, and sweat pH-sensing inks containing photochromic, thermochromic, and pH-chromic materials, respectively, into/onto sustainable starch solution, resulting in a multi-functional, recyclable, and flexible sensing device with high reproducibility. Our results reveal that UV light intensities under sunlight (0-2500 μW/cm²), ambient, and skin temperatures (0-38 °C) as well as sweat pH (4.0-7.0) can be successfully monitored.

Aerosol-Printed MoS2 Ink as a High Sensitivity Humidity Sensor

Molybdenum disulfide (MoS₂) is attractive for use in next-generation nanoelectronic devices and exhibits great potential for humidity sensing applications. Herein, MoS₂ ink was successfully prepared via a simple exfoliation method by sonication. The structural and surface morphology of a deposited ink film was analyzed by scanning electron microscopy (SEM), Raman spectroscopy, and atomic force microscopy (AFM). The aerosol-printed MoS₂ ink sensor has high sensitivity, with a conductivity increase by 6 orders of magnitude upon relative humidity increase from 10 to 95% at room temperature. The sensor also has fast response/recovery times and excellent repeatability. Possible mechanisms for the water-induced conductivity increase are discussed. An analytical model that encompasses two ionic conduction regimes, with a percolation transition to an insulating state below a low humidity threshold, describes the sensor response successfully. In conclusion, our work provides a low-cost and straightforward strategy for fabricating a high-performance humidity sensor and fundamental insights into the sensing mechanism.

Preparation and Research of a High-Performance ZnO/SnO2 Humidity Sensor

A high-performance zinc oxide/tin dioxide (ZnO/SnO₂) humidity sensor was developed using a simple solvothermal method. The sensing mechanism of the ZnO/SnO₂ humidity sensor was evaluated by analyzing its complex impedance spectra. The experimental results prove that the ZnO/SnO₂ composite material has a larger specific surface area than pure SnO₂, which allows the composite material surface to adsorb more water to enhance the response of the ZnO/SnO₂ humidity sensor. ZnO can also contribute to the generation of oxygen-rich vacancies on the ZnO/SnO₂ composite material surface, allowing it to adsorb a large amount of water and rapidly decompose water molecules into conductive ions to increase the response and recovery speed of the ZnO/SnO₂ humidity sensor. These characteristics allowed the Z/S-2 humidity sensor to achieve a higher response (1,225,361%), better linearity, smaller hysteresis (6.6%), faster response and recovery speeds (35 and 8 s, respectively), and long-term stability at 11–95% relative humidity. The successful preparation of the ZnO/SnO₂ composite material also provides a new direction for the design of SnO₂-based resistance sensors with high humidity-sensing performance.

Chemiluminescence-Derived Self-Powered Photoelectrochemical Immunoassay for Detecting a Low-Abundance Disease-Related Protein

Early diagnosis of cancers relies on the sensitive detection of specific biomarkers, but most of the current testing methods are inaccessible to home healthcare due to cumbersome steps, prolonged testing time, and utilization of toxic and hazardous substances. Herein, we developed a portable self-powered photoelectrochemical (PEC) sensing platform for rapid detection of prostate-specific antigen (PSA, as a model disease-related protein) by integrating a self-powered photoelectric signal output system catalyzed with chemiluminescence-functionalized Au nanoparticles (AuNPs) and a phosphomolybdic acid (PMA)-based photochromic visualization platform. TiO₂-g-C₃N₄-PMA photosensitive materials were first synthesized and functionalized on a sensor chip. The sensor consisted of filter paper modified with a photocatalytic material and a regional laser-etched FTO electrode as an alternative to a conventional PEC sensor with a glass-based electrode. The targeting system involved a monoclonal anti-PSA capture antibody-functionalized Fe₃O₄ magnetic bead (mAb₁-MB) and a polyclonal anti-PSA antibody (pAb₂)-N-(4-aminobutyl)-N-ethylisoluminol-AuNP (ABEI-AuNP). Based on the signal intensity of the chemiluminescent system, the photochromic device color changed from light yellow to heteropoly blue through the PMA photoelectric materials integrated into the electrode for visualization of the signal output. In addition, the electrical signal in the PEC system was amplified by a sandwich-type capacitor and readout on a handheld digital multimeter. Under optimum conditions, the sensor exhibited high sensitivity relative to PSA in the range of 0.01-50 ng mL^-1 with a low detection limit of 6.25 pg mL^-1. The flow-through chemiluminescence reactor with a semiautomatic injection device and magnetic separation was avoid of unstable light source intensity inherent in the chemiluminescence process. Therefore, our strategy provides a new horizon for point-of-care analysis and rapid cost-effective clinical diagnosis.