Biomimetic superhydrophobic surface of high adhesion fabricated with micronano binary structure on aluminum alloy

Robust Superhydrophobic Films Based on an Eco-Friendly Poly(l-lactic acid)/Cellulose Composite with Controllable Water Adhesion

Poly(l-lactic acid) (PLLA) featuring desirable biodegradability and biocompatibility has been recognized as one of the promising eco-friendly biomaterials. However, low crystallization and poor mechanical and chemical performances dramatically hamper its practical application. In this work, we report that functionalized cellulose/PLLA composite superhydrophobic stereocomplex films with controllable water adhesion and protein adsorption can be fabricated by a facile approach for the first time. First, cellulose is surface-modified by means of two silanization modification methods. Then, superhydrophobic cellulose/PLLA composite films are prepared through a solvent-evaporation-induced phase separation method. The two cellulose/PLLA composite films exhibit extreme water repellency but tunable water adhesion from sticky to slippery. The protein adsorption capacity of the cellulose/PLLA composite films can also be regulated. In addition, the stereocomplexation of the composite film provides excellent mechanical properties with an elongation at break of 22.36%, which is 237.8% higher than that of a pure PLLA film, which is more suitable for biomaterials. Furthermore, good biodegradability of the PLLA composite films in nature enables the bio-based composites as alternative materials to replace conventional petroleum-based polymers. The superhydrophobic films have also been demonstrated for many applications, including slippery surfaces, liquid transportation without loss, and antifouling.

Durable Biomimetic Two-Tier Structured Superhydrophobic Surface with Ultralow Adhesion and Effective Antipollution Property

Superhydrophobic surfaces with low adhesion have attracted great attention in recent years owing to their extensive applications. Enlightened by multifunctional rice leaves, a micro/nanobinary structured superhydrophobic surface was successfully fabricated on the Ti6Al4V substrate by photoetching, acid etching, alkaline etching, as well as fluorination treatments. Water droplets exhibited a Cassie impregnating wetting state on this superhydrophobic surface, under which the contact area fraction of the liquid-air interface caused by primary micron-scale stripped bumps (f_p) and secondary nanoflower-like structures (f_s) were calculated for the first time. The water adhesion force of this nonwetting surface was precisely measured as 7 μN, which was much lower than that (362 μN) of the original flat substrate and the previous reported surfaces. Moreover, this low-adhesive surface displayed good chemical stability after exposing to air, soaking in aqueous solutions (acid, alkaline, and salt), and cyclic icing/melting treatment. It also showed good mechanical durability after a series of abrasion treatments. Besides, this multifunctional superhydrophobic surface exhibited superior antipollution property to different kinds of contaminants. This multifunctional superhydrophobic surface displays a huge potential for industrial droplet transportation and self-cleaning applications.

Investigation of Electrochemical Assisted Deposition of Sol-Gel Silica Films for Long-Lasting Superhydrophobicity

Current methods for the protection of metal surfaces utilize harsh chemical processes, such as organic paint or electro-plating, which are not environment-friendly and require extensive waste treatments. In this study, a two-step approach consisting of electrochemical assisted deposition (EAD) of an aqueous silane solution and a dip coating of a low surface energy silane for obtaining a superhydrophobic self-cleaning surface for the enhanced protection of copper substrate is presented. A porous and hierarchical micro-nanostructured silica basecoat (sol-gel) was first formed by EAD of a methyltriethoxysilane (MTES) precursor solution on a copper substrate. Then, a superhydrophobic top-coat (E-MTES/PFOTS) was prepared with 1H,1H,2H,2H-Perfluorooctyltriethoxysilane (PFOTS) for low surface energy. The superhydrophobic coating exhibited anti-stain properties against milk, cola, and oil, with contact angles of 151°, 151.5°, and 129°, respectively. The EAD deposition potential and duration were effective in controlling the microscopic morphology, surface roughness, and coating thickness. The E-MTES/PFOTS coatings exhibited chemical stability against acids, bases, and abrasion resistance by sandpaper. The proposed 2-layer coating system exhibited strong chemical bonding at the two interfaces and provided a brush-like surface morphology with long-lasting superhydrophobicity. The developed method would provide an environment-friendly and expedient process for uniform protective coatings on complex surfaces.

Insights from molecular simulations on liquid slip over nanostructured surfaces

The current study focuses on non-equilibrium molecular dynamics (NEMD) simulations to investigate the slip properties of water flowing over different nanostructured surfaces. A simulation protocol is developed that applies constant shear stress throughout the fluid before measuring the slip length. Using pseudo-data, the reliability of this protocol in terms of both accuracy and noise of the results for high-slip and multiphase systems is demonstrated. In contrast to the NEMD techniques available in the literature, the protocol also enables a convenient way to compare the slip lengths of different surface coatings. The fluid slip lengths of surface coatings comprising carbon nanotubes on platinum are predicted using the proposed protocol with nitrogen gas trapped in the interstitial gaps. The role of these gas pockets in determining surface slip properties is investigated. The NEMD results from the proposed model compare well with a macroscopic theoretical model for nano-patterned surfaces. Finally, it is concluded that entrapped gas within nanostructures may offer significant drag reduction only if the gas surface coverage is above 95%.

Self-assembled single-crystal bimodal porous GaN exhibiting a petal effect: application as a sensing platform and substrate for optical devices

This paper investigates the petal effect (hydrophobicity and strong adhesion) observed on single-crystal bimodal porous GaN (porous GaN), which has almost the same electrical properties as bulk GaN. The water contact angles of porous GaN were 100°-135° despite the intrinsic hydrophilic nature of GaN. Moreover, it was demonstrated that the petal effect of porous GaN leads to the uniform attachment of water solutions, enabling highly uniform and aggregation-free attachment of chemicals and quantum dots. These results indicate that porous GaN can be applied in quantum dot light-emitting diodes and as an analytical substrate.

Biomimetic superhydrophobic metal/nonmetal surface manufactured by etching methods: A mini review

As an emerging fringe science, bionics integrates the understanding of nature, imitation of nature, and surpassing nature in one aspect, and it organically combines the synergistic complementarity of function and structure–function integrated materials which is of great scientific interest. By imitating the microstructure of a natural biological surface, the bionic superhydrophobic surface prepared by human beings has the properties of self-cleaning, anti-icing, water collection, anti-corrosion and oil–water separation, and the preparation research methods are increasing. The preparation methods of superhydrophobic surface include vapor deposition, etching modification, sol–gel, template, electrostatic spinning, and electrostatic spraying, which can be applied to fields such as medical care, military industry, ship industry, and textile. The etching modification method can directly modify the substrate, so there is no need to worry about the adhesion between the coating and the substrate. The most obvious advantage of this method is that the obtained superhydrophobic surface is integrated with the substrate and has good stability and corrosion resistance. In this article, the different preparation methods of bionic superhydrophobic materials were summarized, especially the etching modification methods, we discussed the detailed classification, advantages, and disadvantages of these methods, and the future development direction of the field was prospected.

Biomimetic Slippery PDMS Film with Papillae-Like Microstructures for Antifogging and Self-Cleaning

Transparent materials with antifogging and self-cleaning ability are of extreme significance for utilization in outdoor solar cell devices to alleviate the performance loss and maintenance costs. Herein, with inspiration from the anti-wetting surfaces in nature, regular papillae-like microstructure arrays (PMAs) inspired by lotus leaves were designed via a common UV lithography combined with a soft replication. Subsequently, the biomimetic slippery polydimethylsiloxane (PDMS) film (BSPF) inspired by the pitcher plant was fabricated successfully by infusing with hydrophobic liquid lubricant. The resultant surface has hydrophobic surface chemistry, a slippery interface, PMAs structure. The wettability, optical characteristic, antifogging property and self-cleaning ability of the PMAs-based BSPF were characterized experimentally. The film displays excellent optical transmittance, antireflection, antifogging, and self-cleaning properties, which is superior to the flat PDMS film (FPF). Remarkably, an average reflection of ∼11.3% in the FPF was reduced to ∼8.9% of the BSPF. In addition, after gradient spray test for 120 s, the antifogging efficiency was close to 100% for the BSPF surface in comparison with the flat PDMS film (FPF), biomimetic PDMS film (BPF) and flat slippery PDMS film (FSPF) (35%, 70% and 85%). Furthermore, we also discovered that the BSPF surface exhibited a better self-cleaning performance toward a variety of liquids than solid dust.

Mechanically Robust and Thermally Stable Colorful Superamphiphobic Coatings

Colorful super anti-wetting coatings are receiving growing attention, but are challenging to invent. Here, we report a general method for preparing mechanically robust and thermally stable colorful superamphiphobic coatings. A composite of palygorskite (PAL) nanorods and iron oxide red (IOR) was prepared by solid-state grinding or hydrothermal reaction, which was then modified by hydrolytic condensation of silanes to form a suspension. Superamphiphobic coatings were prepared by spray-coating the suspension onto substrates. The superamphiphobicity depends upon the surface microstructure and chemical composition, which are controllable by the PAL/IOR concentration and the solid-state grinding time. The colorful coatings show excellent superamphiphobicity with high contact angles and low sliding angles for water and various organic liquids of low surface tension, e.g., toluene and n-decane. The coatings also feature high mechanical, chemical and thermal stability, which is superior to all the reported colorful super anti-wetting coatings. Moreover, superamphiphobic coatings of different colors can be prepared via the same procedure using the other metal oxides instead of IOR. We believe the colorful superamphiphobic coatings may find applications in many fields like anti-climbing of oils and restoration of cultural relics, as the coatings are applicable onto various substrates.

Biomimetic polymeric superhydrophobic surfaces and nanostructures: from fabrication to applications

Numerous research studies have contributed to the development of mature superhydrophobic systems. The fabrication and applications of polymeric superhydrophobic surfaces have been discussed and these have attracted tremendous attention over the past few years due to their excellent properties. In general, roughness and chemical composition, the two most crucial factors with respect to surface wetting, provide the basic criteria for yielding polymeric superhydrophobic materials. Furthermore, with their unique properties and flexible configurations, polymers have been one of the most efficient materials for fabricating superhydrophobic materials. This review aims to summarize the most recent progress in polymeric superhydrophobic surfaces. Significantly, the fundamental theories for designing these materials will be presented, and the original methods will be introduced, followed by a summary of multifunctional superhydrophobic polymers and their applications. The principles of these methods can be divided into two categories: the first involves adding nanoparticles to a low surface energy polymer, and the other involves combining a low surface energy material with a textured surface, followed by chemical modification. Notably, surface-initiated radical polymerization is a versatile method for a variety of vinyl monomers, resulting in controlled molecular weights and low polydispersities. The surfaces produced by these methods not only possess superhydrophobicity but also have many applications, such as self-cleaning, self-healing, anti-icing, anti-bioadhesion, oil-water separation, and even superamphiphobic surfaces. Interestingly, the combination of responsive materials and roughness enhances the responsiveness, which allows the achievement of intelligent transformation between superhydrophobicity and superhydrophilicity. Nevertheless, surfaces with poor physical and chemical properties are generally unable to withstand the severe conditions of the outside world; thus, it is necessary to optimize the performances of such materials to yield durable superhydrophobic surfaces. To sum up, some challenges and perspectives regarding the future research and development of polymeric superhydrophobic surfaces are presented.

Recent advances in the study and design of parahydrophobic surfaces: From natural examples to synthetic approaches

Parahydrophobic surfaces are an interesting class of materials that combines both high contact angles and very strong adhesion with wetting fluids, most commonly water. This unique set of properties makes parahydrophobic surfaces attractive for a variety of applications, including water harvesting and collection, guided fluid transport, and membrane development, amongst many others. Taking inspiration from natural surfaces that display this same behavior such as rose petals and gecko feet, synthetic approaches aim to incorporate the nano- and micro-scale topography as well as the low surface energy chemistry found on these interfaces. Here, we discuss the chemical and physical factors that contribute to parahydrophobic behavior and provide a comprehensive overview on the current technologies and procedures used towards constructing surfaces that mimic this behavior already observed in nature. This includes etching processes, colloidal assemblies, deposition methods, and in situ growth of surface features. Furthermore, issues such as ease of scale-up, efficiency of technical procedures, and other current challenges associated with these methods will be discussed to provide insight as to the future directions for this growing area of research.

Recent Advances in TiO2 -Based Nanostructured Surfaces with Controllable Wettability and Adhesion

Bioinspired surfaces with special wettability and adhesion have attracted great interest in both fundamental research and industry applications. Various kinds of special wetting surfaces have been constructed by adjusting the topographical structure and chemical composition. Here, recent progress of the artificial superhydrophobic surfaces with high contrast in solid/liquid adhesion has been reviewed, with a focus on the bioinspired construction and applications of one-dimensional (1D) TiO2-based surfaces. In addition, the significant applications related to artificial super-wetting/antiwetting TiO2-based structure surfaces with controllable adhesion are summarized, e.g., self-cleaning, friction reduction, anti-fogging/icing, microfluidic manipulation, fog/water collection, oil/water separation, anti-bioadhesion, and micro-templates for patterning. Finally, the current challenges and future prospects of this renascent and rapidly developing field, especially with regard to 1D TiO2-based surfaces with special wettability and adhesion, are proposed and discussed.

Nonsolvent-assisted fabrication of multi-scaled polylactide as superhydrophobic surfaces

The solution-processing fabrication of superhydrophobic surfaces is currently intriguing, owing to high-efficiency, low cost, and energy-consuming. Here, a facile nonsolvent-assisted process was proposed for the fabrication of the multi-scaled surface roughness in polylactide (PLA) films, thereby resulting in a significant transformation in the surface wettability from intrinsic hydrophilicity to superhydrophobicity. Moreover, it was found that the surface topographical structure of PLA films can be manipulated by varying the compositions of the PLA solutions. And the samples showed superhydrophobic surfaces as well as high melting enthalpy and crystallinity. In particular, a high contact angle of 155.8° together with a high adhesive force of 184 μN was yielded with the assistance of a multi-nonsolvent system, which contributed to the co-existence of micro-/nano-scale hierarchical structures.

Wettability and drag reduction of a superhydrophobic aluminum surface

The friction drag versus the velocity of the water flowing over surfaces with different adhesion properties.

Bioinspired multifunctional Au nanostructures with switchable adhesion

Inspired by the self-cleaning of cicada wings, well-aligned Au-coated Ni nanocone arrays (Au@Ni NAs) have been fabricated by a simple and cheap electrodeposition method. After surface modification of n-hexadecanethiol, self-cleaning can be realized on this long-lived superhydrophobic surface with extremely low adhesive force. Switchable adhesion is obtained on its complementary porous surface. The porous Au structure is fabricated by a geometric replica of the nanocone arrays. After the same surface modification, it shows superhydrophobicity with high adhesion. The different adhesive behaviors on the two lock-and-key Au structures are ascribed to their different contact modes with a water droplet. Combining the superhydrophobic properties of the two complementary structures, they can be used to transport precious microdroplets without any loss. The bioinspired periodic Au@Ni NAs can also be potentially employed as surface-enhanced Raman scattering (SERS) substrates due to its electromagnetic enhancement effect, especially at the tips of the nanocones. Thus, superhydrophobic, SERS, long-lived, self-cleaning, microtransportation functions are realized on the basis of the two surfaces.

Robust biomimetic-structural superhydrophobic surface on aluminum alloy

The following facile approach has been developed to prepare a biomimetic-structural superhydrophobic surface with high stabilities and strong resistances on 2024 Al alloy that are robust to harsh environments. First, a simple hydrothermal treatment in a La(NO3)3 aqueous solution was used to fabricate ginkgo-leaf like nanostructures, resulting in a superhydrophilic surface on 2024 Al. Then a low-surface-energy compound, dodecafluoroheptyl-propyl-trimethoxylsilane (Actyflon-G502), was used to modify the superhydrophilic 2024 Al, changing the surface character from superhydrophilicity to superhydrophobicity. The water contact angle (WCA) of such a superhydrophobic surface reaches up to 160°, demonstrating excellent superhydrophobicity. Moreover, the as-prepared superhydrophobic surface shows high stabilities in air-storage, chemical and thermal environments, and has strong resistances to UV irradiation, corrosion, and abrasion. The WCAs of such a surface almost remain unchanged (160°) after storage in air for 80 days, exposure in 250 °C atmosphere for 24 h, and being exposed under UV irradiation for 24 h, are more than 144° whether in acidic or alkali medium, and are more than 150° after 48 h corrosion and after abrasion under 0.98 kPa for 1000 mm length. The remarkable durability of the as-prepared superhydrophobic surface can be attributed to its stable structure and composition, which are due to the existence of lanthanum (hydr)oxides in surface layer. The robustness of the as-prepared superhydrophobic surface to harsh environments will open their much wider applications. The fabricating approach for such robust superhydrophobic surface can be easily extended to other metals and alloys.

Hierarchically ordered self-lubricating superhydrophobic anodized aluminum surfaces with enhanced corrosion resistance

Herein, we report a facile method for the fabrication of self-lubricating superhydrophobic hierarchical anodic aluminum oxide (AAO) surfaces with improved corrosion protection, which is greatly anticipated to have a high impact in catalysis, aerospace, and the shipping industries. This method involves chemical grafting of as-formed AAO using low surface free energy molecules like long chain saturated fatty acids, perfluorinated fatty acid (perfluorooctadecanoic acid, PFODA), and perfluorosulfonicacid-polytetrafluoroethylene copolymer. The pre and post treatment processes in the anodization of aluminum (Al) play a vital role in the grafting of fatty acids. Wettability and surface free energy were analyzed using a contact angle meter and achieved 161.5° for PFODA grafted anodized aluminum (PFODA-Al). This study was also aimed at evaluating the surface for corrosion resistance by Tafel polarization and self-lubricating properties by tribological studies using a pin-on-disc tribometer. The collective results showed that chemically grafted AAO nanostructures exhibit high corrosion resistance toward seawater and low frictional coefficient due to low surface energy and self-lubricating property of fatty acids covalently linked to anodized Al surfaces.