Monolithic composites of silica aerogels by reactive supercritical deposition of hydroxy-terminated poly(dimethylsiloxane)

Superelastic Clay/Silicone Composite Sponges and Their Applications for Oil/Water Separation and Solar Interfacial Evaporation

3D porous materials are of great interest in many areas of study, but it is still difficult to prepare those with high elasticity and low thermal conductivity via facile methods. Here, superelastic laponite/silicone (LS) composite sponges with low thermal conductivity are prepared via a simple approach. The LS sponges were analyzed by various characterization methods. The content of laponite nanosheets in LS sponges has a great influence on the microstructure, comprehensive mechanical properties, and thermal conductivity. LS sponges feature (i) high mechanical strength, compressibility, and elasticity, (ii) excellent superhydrophobicity/superoleophilicity, and (iii) low thermal conductivity. Consequently, LS sponges could be used for water purification, for example, oil/water separation and solar-driven interfacial evaporation in combination with carbon nanotubes (CNTs). The LS/CNTs solar evaporator has a remarkable evaporation rate of 1.77 kg m^-2 h^-1 for the 3.5 wt % NaCl aqueous solution under 1 kW m^-2 irradiation and high salt resistance. We foresee that this study will promote the development of new 3D porous materials and their applications.

Gradual hydrophobization of silica aerogel for controlled drug release

We report on the successful fine-tuning of silica aerogel hydrophobicity, through a gas-phase surface modification process. Aerogel hydrophobicity is a widely discussed matter, as it contributes to the aerogel's preservation and determines its functionality. Still, a general procedure for tuning the hydrophobicity, without affecting other aerogel properties was missing. In the developed procedure, silica aerogel was modified with trimethylchlorosilane vapor for varying durations, resulting in gradual hydrophobicity, determined by solid-state NMR and contact angle measurements. The generality of this post-synthesis treatment allows its application on a variety of aerogel materials, while having minimum effect on their porosity and transparency. We demonstrate the applicability of the gradual hydrophobization by tuning drug release rates from the silica aerogel. Two chlorhexidine salts - widely employed as antiseptic agents - were used as model drugs, one representing a soluble drug, and the other an insoluble drug; they were entrapped in silica aerogel, following hydrophobization to varying degrees. The drug release patterns showed that depending on the degree, hydrophobization can increase or decrease release kinetics, compared to the unmodified aerogel. This arises from the effect of the hydrophobic degree on pore structure, diffusional rates and wetting of the aerogel carrier. We suggest the use of the gradual hydrophobization process for other drug-aerogel systems, as well as for other aerogel applications, such as transparent insulation panels, contaminate sorbents or catalysis supports.

Silica Aerogel Monoliths Derived from Silica Hydrosol with Various Surfactants

Owing to their ultra-low thermal conductivity, silica aerogels are promising thermal insulators; however, their extensive application is limited by their high production cost. Thus, scientists have started to explore low-cost and easy preparation processes of silica aerogels. In this work, a low-cost method was proposed to prepare silica aerogels with industrial silica hydrosol and a subsequent ambient pressure drying (APD) process. Various surfactants (cationic, amphoteric, or anionic) were added to avoid solvent exchange and surface modification during the APD process. The effects of various surfactants on the microstructure, thermal conductivity, and thermal stability of the silica aerogels were studied. The results showed that the silica aerogels prepared with a cationic or anionic surfactant have better thermal stability than that prepared with an amphoteric surfactant. After being heated at 600 °C, the silica aerogel prepared with a cationic surfactant showed the highest specific surface area of 131 m²∙g^-1 and the lowest thermal conductivity of 0.038 W∙m^-1∙K^-1. The obtained low-cost silica aerogel with low thermal conductivity could be widely applied as a thermal insulator for building and industrial energy-saving applications.

Cast-In-Situ, Large-Sized Monolithic Silica Xerogel Prepared in Aqueous System

This paper reports the preparation of cast-in-situ, large-sized monolithic silica xerogels by a two-step acid–base catalyzed approach under ambient pressure drying. Low-cost industrial silica sol and deionized water were used as the silicon source and the solvent, respectively. Hexadecetyltrimethylammonium bromide (CTAB) was used as a modification agent. Different amounts of polyethylene glycol 400 (PEG400) was added as a pore-forming agent. The prepared silica xerogels under ambient pressure drying have a mesoporous structure with a low density of 221 mg·cm⁻³ and a thermal conductivity of 0.0428 W·m⁻¹·K⁻¹. The low-cost and facile preparation process, as well as the superior performance of the monolithic silica xerogels make it a promising candidate for industrial thermal insulation materials.

A Co-Precursor Approach Coupled with a Supercritical Modification Method for Constructing Highly Transparent and Superhydrophobic Polymethylsilsesquioxane Aerogels

Polymethylsilsesquioxane (PMSQ) aerogels obtained from methyltrimethoxysilane (MTMS) are well-known high-performance porous materials. Highly transparent and hydrophobic PMSQ aerogel would play an important role in transparent vacuum insulation panels. Herein, the co-precursor approach and supercritical modification method were developed to prepare the PMSQ aerogels with high transparency and superhydrophobicity. Firstly, benefiting from the introduction of tetramethoxysilane (TMOS) in the precursor, the pore structure became more uniform and the particle size was decreased. As the TMOS content increased, the light transmittance increased gradually from 54.0% to 81.2%, whereas the contact angle of water droplet decreased from 141° to 99.9°, ascribed to the increase of hydroxyl groups on the skeleton surface. Hence, the supercritical modification method utilizing hexamethyldisilazane was also introduced to enhance the hydrophobic methyl groups on the aerogel’s surface. As a result, the obtained aerogels revealed superhydrophobicity with a contact angle of 155°. Meanwhile, the developed surface modification method did not lead to any significant changes in the pore structure resulting in the superhydrophobic aerogel with a high transparency of 77.2%. The proposed co-precursor approach and supercritical modification method provide a new horizon in the fabrication of highly transparent and superhydrophobic PMSQ aerogels.

Organic–inorganic hybridization for the synthesis of robust in situ hydrophobic polypropylsilsesquioxane aerogels with fast oil absorption properties

In situ hydrophobic polypropylsilsesquioxane aerogels (PSAs) were successfully synthesized via an organic–inorganic hybridization method by a sol–gel process, in which propyltriethoxysilane (PTES) and tetraethylorthosilicate (TEOS) were used as co-precursors. ²⁹Si NMR and FTIR analyses indicated the high degree of condensation of the precursors and proved the attachment of propyl (–C₃H₇) groups in PSAs, respectively. By means of incorporating propyl groups, both mechanical robustness and in situ hydrophobicity were obtained. Meanwhile, the mechanical strength, contact angle and density obviously increased with the increase in propyl groups. Under optimized conditions, as-prepared PSA could endure up to a 70% maximum linear compression with few cracks. Benefiting from the robust structure and in situ hydrophobicity, PSAs showed high absorption capacities (8–10 times that of its own weight) and fast absorption properties (<20 s) for a wide range of organic solvents and could be reused at least 5 times.

In situ hydrophobic and mechanically robust polypropylsilsesquioxane aerogels (PSAs) were successfully synthesized via an organic–inorganic hybridization method by a sol–gel process.

Silica-titania composite aerogel photocatalysts by chemical liquid deposition of titania onto nanoporous silica scaffolds

Silica-titania composite aerogels were synthesized by chemical liquid deposition of titania onto nanoporous silica scaffolds. This novel deposition process was based on chemisorption of partially hydrolyzed titanium alkoxides from solution onto silica nanoparticle surfaces and subsequent hydrolysis and condensation to afford titania nanoparticles on the silica surface. The titania is homogeneously distributed in the silica-titania composite aerogels, and the titania content can be effectively controlled by regulating the deposition cycles. The resultant composite aerogel with 15 deposition cycles possessed a high specific surface area (SSA) of 425 m(2)/g, a small particle size of 5-14 nm, and a large pore volume and pore size of 2.41 cm(3)/g and 18.1 nm, respectively, after heat treatment at 600 °C and showed high photocatalytic activity in the photodegradation of methylene blue under UV-light irradiation. Its photocatalytic activity highly depends on the deposition cycles and heat treatment. The combination of small particle size, high SSA, and enhanced crystallinity after heat treatment at 600 °C contributes to the excellent photocatalytic property of the silica-titania composite aerogel. The higher SSAs compared to those of the reported titania aerogels (<200 m(2)/g at 600 °C) at high temperatures combined with the simple method makes the silica-titania aerogels promising candidates as photocatalysts.

An emerging platform for drug delivery: aerogel based systems

Over the past few decades, advances in "aerogel science" have provoked an increasing interest for these materials in pharmaceutical sciences for drug delivery applications. Because of their high surface areas, high porosities and open pore structures which can be tuned and controlled by manipulation of synthesis conditions, nanostructured aerogels represent a promising class of materials for delivery of various drugs as well as enzymes and proteins. Along with biocompatible inorganic aerogels and biodegradable organic aerogels, more complex systems such as surface functionalized aerogels, composite aerogels and layered aerogels have also been under development and possess huge potential. Emphasis is given to the details of the aerogel synthesis and drug loading methods as well as the influence of synthesis parameters and loading methods on the adsorption and release of the drugs. Owing to their ability to increase the bioavailability of low solubility drugs, to improve both their stability and their release kinetics, there are an increasing number of research articles concerning aerogels in different drug delivery applications. This review presents an up to date overview of the advances in all kinds of aerogel based drug delivery systems which are currently under investigation.

A versatile ambient pressure drying approach to synthesize silica-based composite aerogels

A general ambient pressure drying approach to synthesize silica-based composite aerogels with high BET surfaces and large pore volumes has been reported.

Ultra-flyweight hydrophobic poly(m-phenylenediamine) aerogel with micro-spherical shell structures as a high-performance selective adsorbent for oil contamination

Ultra-flyweight hydrophobic poly(mphenylenediamine) aerogel which can be used as high-performance selective adsorbent for oil contamination was fabricated via a simple two step approach from a poly(m-phenylenediamine) micro-spherical shell.