Sustainable polyelectrolyte multilayer surfaces: possible matrix for salt/dye separation

Low Fouling Polyelectrolyte Layer-by-Layer Self-Assembled Membrane for High Performance Dye/Salt Fractionation: Sequence Effect of Self-Assembly

Layer-by-layer (LbL) self-assembly of oppositely charged polyelectrolytes (PEs) is usually performed on a conventional ultrafiltration base substrate (negative zeta potential) by depositing a cationic PE as a first layer. Herein, we report the facile and fast formation of high performance molecular selective membrane by the nonelectrostatic adsorption of anionic PE on the polyvinylidene fluoride (PVDF, zeta potential -17 mV) substrate followed by the electrostatic LbL assembly. Loose nanofiltration membranes have been prepared via both concentration-polarization (CP-LbL, under applied pressure) driven and conventional (C-LbL, dipping) LbL self-assembly. When the first layer is poly(styrene sodium) sulfonic acid, the LbL assembled membrane contains free -SO3- groups and exhibits higher rejection of Na2SO4 and lower rejection of MgCl2. The reversal of salt rejection occurs when the first layer is quaternized polyvinyl imidazole (PVIm-Me). The membrane (five layers) prepared by first depositing PStSO3Na shows higher rejection of several dyes (97.9 to >99.9%), higher NaCl to dye separation factor (52-1800), and higher dye antifouling performance as compared to the membrane prepared by first depositing PVIm-Me (97.5-99.5% dye rejection, separation factor ∼40-200). However, the C-LbL membrane requires a longer time of self-assembly or higher PE concentration to reach a performance close to the CP-LbL membranes. The membranes exhibit excellent pressure, pH (3-12), and salt (60 g L-1) stability. This work provides an insight for the construction of low fouling and high-performance membranes for the fractionation of dye and salt based on the LbL self-assembly sequence.

Organic micropollutant removal and phosphate recovery by polyelectrolyte multilayer membranes: Impact of buildup interactions

Polyelectrolyte multilayer (PEM) deposition conditions can favorably or adversely affect the membrane filtration performance of various pollutants. Although pH and ionic strength have been proven to alter the characteristics of PEM, their role in determining the buildup interactions that control filtration efficacy has not yet been conclusively proved. A PEM constructed using electrostatic or non-electrostatic interactions from controlled deposition of a weak polyelectrolyte could retain both charged and uncharged pollutants from water. The fundamental relationship between polyelectrolyte charge density, PEM buildup interaction, and filtration performance was explored using a weak-strong electrolyte pair consisting of branching poly (ethyleneimine) and poly (styrene sulfonate) (PSS) across pH ranges of 4-10 and NaCl concentrations of 0 M-0.5 M. PEI/PSS multilayers at acidic pH were dominated by electrostatic interactions, which favored the selective removal of a charged solute, phosphate over chloride, while at alkaline pH, non-electrostatic interactions dominated, which favored the removal of oxybenzone (OXY), a neutral hydrophobic solute. The key factor determining these interactions was the charge density of PEI, which is controlled by pH and ionic strength of the deposition solutions. These findings indicate that the control of buildup interactions can largely influence the physico-chemical and transport characteristics of PEM membranes.

High-strength and anti-bacterial BSA/carboxymethyl chitosan/silver nanoparticles/calcium alginate composite hydrogel membrane for efficient dye/salt separation

In order to solve the problems of poor mechanical property, non-antibacterial and low flux of calcium alginate (CaAlg) membrane, silver nanoparticles (AgNPs) were synthesized with bovine serum albumin (BSA) and carboxymethyl chitosan (CMCS) for improving CaAlg membrane in this paper. Meanwhile, the dispersion property of silver nanoparticles and the mechanical property, thermal stability, antibacterial property and filtration efficiency of the composite membrane were explored. The results illustrated CMCS observably strengthened the mechanical property and thermal stability of the composite membrane, and AgNPs endowed the composite membrane with excellent antibacterial property. The flux of the BSA/CMCS/AgNPs/CaAlg composite membrane was raised compared to CaAlg membrane. Finally, the viscose fiber/polyethylene terephthalate fiber (VF-PET) nonwoven fabric was introduced as the support layer to further improve the filtration flux and mechanical property of the composite membrane. VF-PET/BSA/CMCS/AgNPs/CaAlg membrane had a rejection rate of over 99.0 % for dye molecules and <9.0 % for salt ions, while the flux maintained 38.5 L·m^-2·h^-1. Furthermore, VF-PET/BSA/CMCS/AgNPs/CaAlg membrane also had excellent separation effect on actual dye wastewater. The separation of dye and salt by the membrane mainly depended on the screening mechanism of membrane pore size, rather than adsorption. The composite membrane had an outstanding performance on the separation of dye molecules and inorganic salt ions.

Identification of micropollutants from graywater of different complexity and remediation using multilayered membranes

Graywater reuse is one of the important concepts in attaining water sustainability. A major challenge in this area is to realize various components present in graywater. The present study involves the identification of the chemical components of graywater collected from three different environments and to investigate the efficiency of removal of some of these chemical components using ultrafiltration membranes (polyelectrolyte multilayer (PEM) membranes). The chemical components were analyzed using liquid chromatography connected with quadrupole time-of-flight (UPLC-Q-ToF-MS). A number of micropollutants including surfactants and certain contaminants of emerging concern (CECs) were identified from these samples. Out of 16 compounds identified, 13 were surfactants and the remaining were caffeine, oxybenzone, and benzophenone. These surfactants are mostly the ingredients of various detergents. Low-pressure filtration studies of the collected samples were carried out utilizing chitosan/polyacrylic acid (CHI/PAA) multilayer membranes. A 5.5 bilayer membrane showed more than 95% rejection of the identified compounds in the selected samples and significant improvement in the water quality parameters. This demonstrates that the membrane used in this work is effective in the removal of various chemicals from graywater as well as enhancing the water quality.

Occurrence, distribution and removal of organic micro-pollutants in a low saline water body

A low saline backwater canal, mainly utilized for domestic and agricultural purposes, has been analyzed for the possible presence of organic micropollutants (OMP) and their potential removal was explored by multilayered microfiltration membranes. The qualitative as well as quantitative analysis were carried out for a span of one year using the technique of liquid chromatography connected with high resolution mass spectrometry (LC-Q-TOF-MS). The identification of the formally unknown compounds was initially done using non-target analysis based on the mass accuracy, isotopic pattern and MS/MS spectral interpretation. Results of the non target screening revealed the presence of 11 OMPs. Five of these OMPs were confirmed using standards; these include chlorophene (CHP), oxybenzone (OXY), N, N-diethyl-meta-toluamide (DEET), N, N-diethyl-benzamide (DEB) and dibutyl phthalate (DBP). Among the confirmed OMPs, the highest concentration was observed for DBP (244.61 ng l^-1). The most frequently observed OMP in the study area was DBP while the least was DEB which is an insect repellent as well as a degradation product of DEET. The ecological risk associated with the target compounds has also been analyzed by calculating the risk quotient (RQ) and the results revealed that at the detected levels, these compounds are capable of causing low to medium risk. Low pressure (<0.3 bar) filtrations of the compounds were attempted using microfiltration (MF) and, poly(ethyleneimine)/poly(styrene sulfonate) (PEI/PSS) multi-layered MF membrane for spiked ultrapure water and also for natural water from the back-water canal. The batch mode illustrates nearly complete removal of CHP and OXY in spiked solutions and a good removal efficiency from natural water. The effect of coexisting ions and surfactants in feed is also illustrated. The high efficiency of the removal of both CHP and OXY, in such a complex medium highlights the potential application of the present method for the removal of similar OMPs in natural waters.

Low - cost multilayered green fiber for the treatment of textile industry waste water

Layer by layer (LbL) assembly can be regarded as an emerging technology for the separation of organic micro-pollutants from water. Direct assembly of polyelectrolytes (PEs) under LbL mode on natural support material is rare. Here we report the integration of LbL to one of the most resourceful support materials that might have an enduring impact on water treatment in color industry. A low-cost adsorbent is developed from chitosan (CHI) and polyacrylic acid (PAA) through LbL deposition on coir fiber (CF) by alternate exposure to their aqueous solutions. Their layer dependent formation is characterized by spectroscopic and microscopic techniques. CHI/PAA multilayer coated coir fiber or simply, layered coir fiber (LCF) showed high loading of cationic and anionic dyes both at acidic and alkaline loading pH. The loading was between 70% and 99% at the acidic pH 3 which is attributed to the binding between LCF and dye molecules by electrostatic and hydrophobic forces. The performance of LCF in presence of NaCl, Na₂SO₄ and sodium dodecyl sulfate (SDS) in dye solution is discussed. Textile industrial waste water showed significant reduction in dye (81%) content along with COD (84%) and TDS.

Antimicrobial efficiency of PAA/(PVP/CHI) erodible polysaccharide multilayer through loading and controlled release of antibiotics

The adhesion of bacteria and subsequent formation of biofilm on the surface of implants greatly affect the long-term use of the implants. The low molar mass gentamicin (GS) cations could hardly be directly incorporated into the multilayer films through alternately deposition with a polyanion. Herein, we have designed and constructed a (poly(acrylic acid)/(polyvinylpyrrolidone/chitosan))_n ((PAA/(PVP/CHI))_n) multilayer films through layer-by-layer self-assembly method. Through increasing the pH to destroy hydrogen bonding between PAA and PVP, PVP released into the solution and GS simultaneously combined with PAA through electrostatic interactions. The loading dosage of GS into the (PAA/(PVP/CHI))₁₀ multilayer film was up to 153.84±18.64μg/cm² and could be precisely tuned through changing the thickness of the films. The release behaviour of GS in phosphate buffer saline could also be regulated through thermal cross-linking of the films. The drug-loaded multilayer films displayed efficient against three kinds of Gram-positive and three kinds of Gram-negative bacteria and one kind of fungi, and good biocompatibility towards human lens epithelial cells. GS-loaded multilayer films-coated polydimethylsiloxane (PDMS) were compared with pristine PDMS in the rabbit subcutaneous S. aureus infection model. The antimicrobial-coated implants yielded a much lower degree of infections than pristine implants at day seven.

Oriented Clay Nanotube Membrane Assembled on Microporous Polymeric Substrates

Organized arrays of halloysite clay nanotubes have great potential in molecular separation, absorption, and biomedical applications. A highly oriented layer of halloysite on polyacrylonitrile porous membrane was prepared via a facile evaporation-induced method. Scanning electronic microscopy, surface attenuated total reflection Fourier transform infrared spectroscopy, and energy dispersive X-ray spectroscopy mapping indicated formation of the nanoarchitecture-controlled membrane. The well-ordered nanotube coating allowed for the excellent dye rejection (97.7% for reactive black 5) with high salt permeation (86.5% for aqueous NaCl), and thus these membranes were suitable for dye purification or concentration. These well-aligned nanotubes' composite membranes also showed very good fouling resistance against dye accumulation and bovine serum albumin adsorption as compared to the pristine polyacrylonitrile or membrane coated with disordered halloysite layer.