Wet chemical synthesis of soluble gold nanogaps

Massively Parallel Arrays of Size-Controlled Metallic Nanogaps with Gap-Widths Down to the Sub-3-nm Level

Metallic nanogaps (MNGs) are fundamental components of nanoscale photonic and electronic devices. However, the lack of reproducible, high-yield fabrication methods with nanometric control over the gap-size has hindered practical applications. A patterning technique based on molecular self-assembly and physical peeling is reported here that allows the gap-width to be tuned from more than 30 nm to less than 3 nm. The ability of the technique to define sub-3-nm gaps between dissimilar metals permits the easy fabrication of molecular rectifiers, in which conductive molecules bridge metals with differing work functions. A method is further described for fabricating massively parallel nanogap arrays containing hundreds of millions of ring-shaped nanogaps, in which nanometric size control is maintained over large patterning areas of up to a square centimeter. The arrays exhibit strong plasmonic resonances under visible light illumination and act as high-performance substrates for surface-enhanced Raman spectroscopy, with high enhancement factors of up to 3 × 108 relative to thin gold films. The methods described here extend the range of metallic nanostructures that can be fabricated over large areas, and are likely to find many applications in molecular electronics, plasmonics, and biosensing.

Parallel Fabrication of Self-Assembled Nanogaps for Molecular Electronic Devices

Single molecule electronics might be a way to add additional function to nanoscale devices and continue miniaturization beyond current state of the art. Here, a combined top-down and bottom-up strategy is employed to assemble single molecules onto prefabricated electrodes. Protodevices, which are self-assembled nanogaps composed by two gold nanoparticles linked by a single or a few molecules, are guided onto top-down prefabricated nanosized nickel electrodes with sandwiched palladium layers. It is shown that an optimized geometry of multilayered metallic (top-down) electrodes facilitates the assembly of (bottom-up) nanostructures by surface charge interactions. Moreover, such assembly process results in an electrode-nanoparticle interface free from linking molecules that enable electrical measurements to probe electron transport properties of the nanoparticle-molecule-nanoparticle protodevices.

Fabrication of a Horizontal and a Vertical Large Surface Area Nanogap Electrochemical Sensor

Nanogap sensors have a wide range of applications as they can provide accurate direct detection of biomolecules through impedimetric or amperometric signals. Signal response from nanogap sensors is dependent on both the electrode spacing and surface area. However, creating large surface area nanogap sensors presents several challenges during fabrication. We show two different approaches to achieve both horizontal and vertical coplanar nanogap geometries. In the first method we use electron-beam lithography (EBL) to pattern an 11 mm long serpentine nanogap (215 nm) between two electrodes. For the second method we use inductively-coupled plasma (ICP) reactive ion etching (RIE) to create a channel in a silicon substrate, optically pattern a buried 1.0 mm × 1.5 mm electrode before anodically bonding a second identical electrode, patterned on glass, directly above. The devices have a wide range of applicability in different sensing techniques with the large area nanogaps presenting advantages over other devices of the same family. As a case study we explore the detection of peptide nucleic acid (PNA)−DNA binding events using dielectric spectroscopy with the horizontal coplanar device.

Solution-Processable Carbon Nanoelectrodes for Single-Molecule Investigations

Here we present a solution-based assembly method for producing molecular transport junctions employing metallic single-walled carbon nanotubes as nanoelectrodes. The molecular junction conductance of a series of oligophenyls was successfully measured, highlighting the potential of an all-carbon based approach for the fabrication of solution-processable single-molecule junctions for molecular electronics.

Gold nanoparticles as sensitive optical probes

Recent advances in Au NP based optical sensing systems for various analytes based on absorption, fluorescence and SERS are summarized.

Gold nanoparticles assembled with dithiocarbamate-anchored molecular wires

A protocol for the bottom-up self-assembly of nanogaps is developed through molecular linking of gold nanoparticles (AuNPs). Two π-conjugated oligo(phenylene ethynylene) molecules (OPE) with dithiocarbamate anchoring groups are used as ligands for the AuNPs. OPE-4S with a dithiocarbamate in each end of the molecule and a reference molecule OPE-2S with only a single dithiocarbamate end group. The linking mechanism of OPE-4S is investigated by using a combination of TEM, UV-Vis absorption and surface enhanced Raman spectroscopy (SERS) as well as studying the effect of varying the OPE-4S to AuNP concentration ratio. UV-Vis absorption confirms the formation of AuNP aggregates by the appearance of an extended plasmon band (EPB) for which the red shift and intensity depend on the OPE-4S:AuNP ratio. SERS confirms the presence of OPE-4S and shows a gradual increase of the signal intensity with increasing OPE-4S:AuNP ratios up to a ratio of about 4000, after which the SERS intensity does not increase significantly. For OPE-2S, no linking is observed below full coverage of the AuNPs indicating that the observed aggregate formation at high OPE-2S:AuNP ratios, above full AuNP coverage, is most likely of a physical nature (van der Waals forces or π-π interactions).

The conquest of middle-earth: combining top-down and bottom-up nanofabrication for constructing nanoparticle based devices

The development of top-down nanofabrication techniques has opened many possibilities for the design and realization of complex devices based on single molecule phenomena such as e.g. single molecule electronic devices. These impressive achievements have been complemented by the fundamental understanding of self-assembly phenomena, leading to bottom-up strategies to obtain hybrid nanomaterials that can be used as building blocks for more complex structures. In this feature article we highlight some relevant published work as well as present new experimental results, illustrating the versatility of self-assembly methods combined with top-down fabrication techniques for solving relevant challenges in modern nanotechnology. We present recent developments on the use of hierarchical self-assembly methods to bridge the gap between sub-nanometer and micrometer length scales. By the use of non-covalent self-assembly methods, we show that we are able to control the positioning of nanoparticles on surfaces, and to address the deterministic assembly of nano-devices with potential applications in plasmonic sensing and single-molecule electronics experiments.

Assembling single gold nanorods into large-scale highly aligned nanoarrays via vacuum-enhanced capillarity

We report a simple, straightforward, and efficient approach to assemble single gold nanorods (AuNRs) into highly aligned arrays, via a unique vacuum-enhanced capillarity. The assembled AuNR arrays demonstrate both an excellently unidirectional ordering and a wonderful single-rod resolution. The key role of vacuum in this approach enables high-aspect-ratio (10 to 22) AuNR alignment and efficiently facilitates large-area alignment. Further investigation of one- and two-dimensional AuNR arrays would undoubtedly be beneficial to their potential applications.

Single-molecule electronics: from chemical design to functional devices

The use of single molecules in electronics represents the next limit of miniaturisation of electronic devices, which would enable to continue the trend of aggressive downscaling of silicon-based electronic devices.

Bioinspired nanoarchitectonics as emerging drug delivery systems

Bioinspired nanoarchitectonics opens a new era for designing drug delivery systems.