Supported gold catalysis: from small molecule activation to green chemical synthesis

CeO2-Based Frustrated Lewis Pairs via Defective Engineering: Formation Theory, Site Characterization, and Small Molecule Activation

Activation of small molecules is considered to be a central concern in the theoretical investigation of environment- and energy-related catalytic conversions. Sub-nanostructured frustrated Lewis pairs (FLPs) have been an emerging research hotspot in recent years due to their advantages in small molecule activation. Although the progress of catalytic applications of FLPs is increasingly reported, the fundamental theories related to the structural formation, site regulation, and catalytic mechanism of FLPs have not yet been fully developed. Given this, it is attempted to demonstrate the underlying theory of FLPs formation, corresponding regulation methods, and its activation mechanism on small molecules using CeO2 as the representative metal oxide. Specifically, this paper presents three fundamental principles for constructing FLPs on CeO2 surfaces, and feasible engineering methods for the regulation of FLPs sites are presented. Furthermore, cases where typical small molecules (e.g., hydrogen, carbon dioxide, methane oxygen, etc.) are activated over FLPs are analyzed. Meanwhile, corresponding future challenges for the development of FLPs-centered theory are presented. The insights presented in this paper may contribute to the theories of FLPs, which can potentially provide inspiration for the development of broader environment- and energy-related catalysis involving small molecule activation.

Exploration of active sites of ethyl alcohol electro-oxidation on porous gold nanoparticles with enhanced Raman spectroscopy

Novel porous gold nanospheres are prepared by calcination of the gold-urea complexes. The enhanced Raman spectra of ethanol catalyzed by different doses of porous gold nanospheres are measured with a 532 nm laser as the excitation source, and an enhanced charge coupled device served in spectral detection and microscopic imaging. The electrochemical experiments show that the catalytic oxidation products of ethanol with porous gold nanoparticles are acetaldehyde, acetic acid, and water, which further proved that the porous gold nanoparticles can activate the -CH₂ of ethanol.

Supported Gold Nanoparticle-Catalyzed Selective Reduction of Multifunctional, Aromatic Nitro Precursors into Amines and Synthesis of 3,4-Dihydroquinoxalin-2-Ones

The synthesis of 3,4-dihydroquinoxalin-2-ones via the selective reduction of aromatic, multifunctional nitro precursors catalyzed by supported gold nanoparticles is reported. The reaction proceeds through the in situ formation of the corresponding amines under heterogeneous transfer hydrogenation of the initial nitro compounds catalyzed by the commercially available Au/TiO₂-Et₃SiH catalytic system, followed by an intramolecular C-N transamidation upon treatment with silica acting as a mild acid. Under the present conditions, the Au/TiO₂-TMDS system was also found to catalyze efficiently the present selective reduction process. Both transfer hydrogenation processes showed very good functional-group tolerance and were successfully applied to access more structurally demanding products bearing other reducible moieties such as chloro, aldehyde or methyl ketone. An easily scalable (up to 1 mmol), low catalyst loading (0.6 mol%) synthetic protocol was realized, providing access to this important scaffold. Under these mild catalytic conditions, the desired products were isolated in good to high yields and with a TON of 130. A library analysis was also performed to demonstrate the usefulness of our synthetic strategy and the physicochemical profile of the derivatives.

Engineering of Oxide Protected Gold Nanoparticles

Gold nanoparticles that are partially or fully covered by metal oxide shells provide superior functionality and stability for catalytic and plasmonic applications. Yet, facile methods for controlled fabrication of thin oxide layers on metal nanoparticles are lacking. Here, we report an easy method to reliably engineer thin Ga₂O₃ shells on Au nanoparticles, based on liquid-phase chemical oxidation of Au-Ga alloy nanoparticles. We demonstrate that, with this technique, laminar and ultrathin Ga₂O₃ shells can be grown with ranging thickness from sub- to several monolayers. We show how the localized surface plasmon resonance can be used to understand the reaction process and quantitatively monitor the Ga₂O₃ shell growth. Finally, we demonstrate that the Ga₂O₃ coating prevents sintering of the Au nanoparticles, providing thermal stability to at least 250 °C. This approach, building on dealloying of bimetallic nanoparticles by the solution-phase oxidation, promises a general technique for achieving controlled metal/oxide core/shell nanoparticles.

Selective Mild Oxidation of Anilines into Nitroarenes by Catalytic Activation of Mesoporous Frameworks Linked with Gold-Loaded Mn3 O4 Nanoparticles

This work reports the synthesis and catalytic application of mesoporous Au-loaded Mn3 O4 nanoparticle assemblies (MNAs) with different Au contents, i. e., 0.2, 0.5 and 1 wt %, towards the selective oxidation of anilines into the corresponding nitroarenes. Among common oxidants, as well as several supported gold nanoparticle platforms, Au/Mn3 O4 MNAs containing 0.5 wt % Au with an average particle size of 3-4 nm show the best catalytic performance in the presence of tert-butyl hydroperoxide (TBHP) as a mild oxidant. In all cases, the corresponding nitroarenes were isolated in high to excellent yields (85-97 %) and selectivity (>98 %) from acetonitrile or greener solvents, such as ethyl acetate, after simple flash chromatography purification. The 0.5 % Au/Mn3 O4 catalyst can be isolated and reused four times without a significant loss of its activity and can be applied successfully to a lab-scale reaction of p-toluidine (1 mmol) leading to the p-nitrotulene in 83 % yield. The presence of AuNPs on the Mn3 O4 surface enhances the catalytic activity for the formation of the desired nitroarene. A reasonable mechanism was proposed including the plausible formation of two intermediates, the corresponding N-aryl hydroxylamine and the nitrosoarene.

Synergistic Effects of Bimetallic AuPd and La2O3 in the Catalytic Reduction of NO with CO

Bimetallic AuPd nanoparticles supported on TiO2 are known to catalyze the reduction of NO with CO. Here, we investigated the effects of the addition of lanthanum oxide to a AuPd/TiO2 catalyst with a AuPd particle size of 2.1–2.2 nm. The addition of La2O3 enhanced the catalytic activity; for example, at 250 °C, there was 40.9% NO conversion and 49.3% N2-selectivity for AuPd/TiO2, and 100% NO conversion and 100% N2-selectivity for AuPd-La (1:1)/TiO2. The temperature requiring 100% NO conversion dropped from 400 °C to 200 °C by the simple post-impregnation of La2O3 onto AuPd/TiO2. In situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) combined with modulation excitation spectroscopy (MES) demonstrated that CO adsorption occurs first on Au atoms and then, within 80 s, moves onto Pd atoms. This transformation between two adsorption sites was facilitated by the addition of La2O3.

A Multifunctional Au/CeO2-Mg(OH)2 Catalyst for One-Pot Aerobic Oxidative Esterification of Aldehydes with Alcohols to Alkyl Esters

Au nanoparticles bound to crystalline CeO2 nanograins that were dispersed on the nanoplate-like Mg(OH)2, denoted as Au/CeO2-Mg(OH)2, were developed as the highly active and selective multifunctional heterogeneous catalyst for direct oxidative esterification of aldehydes with alcohols to produce alkyl esters under base-free aerobic conditions using oxygen or air as the green oxidants. Au/CeO2-Mg(OH)2 converted 93.3% of methacrylaldehyde (MACR) to methyl methacrylate (MMA, monomer of poly(methyl methacrylate)) with 98.2% selectivity within 1 h, and was repeatedly used over eight recycle runs without regeneration. The catalyst was extensively applied to other aldehydes and alcohols to produce desirable alkyl esters. Comprehensive characterization analyses revealed that the strong metal-support interaction (SMSI) among the three catalytic components (Au, CeO2, and Mg(OH)2), and the proximity and strong contact between Au/CeO2 and the Mg(OH)2 surface were prominent factors that accelerated the reaction toward a desirable oxidative esterification pathway. During the reaction, MACR was adsorbed on the surface of CeO2-Mg(OH)2, upon which methanol was simultaneously activated for esterifying the adsorbed MACR. Hemiacetal-form intermediate species were subsequently produced and oxidized to MMA on the surface of the electron-rich Au nanoparticles bound to partially reduced CeO2-x with electron-donating properties. The present study provides new insights into the design of SMSI-induced supported-metal-nanoparticles for the development of novel, multifunctional, and heterogeneous catalysts.

Hydrogenation of HOPG-Supported Gold Nanoparticles: Surface or Volume?

The hydrogenation features of gold nanoparticles deposited on highly oriented pyrolytic graphite were determined, and composite nanostructures consisting of pure and hydrogenized gold were synthesized. Methods of scanning tunneling microscopy and spectroscopy have been successfully used to probe the bottom of the conductive band and to determine the shape of the electron energy barrier in hydrogenized gold. Considering models of surface and volume hydrogenation, we have shown that no hydrogen dissolution occurred in gold nanoparticles, but all changes in their electronic structure were associated with surface processes. The results of the quantum chemical simulation also corresponded with this conclusion.

Effect of ultra-low amount of gold in oxide-supported bimetallic Au–Fe and Au–Cu catalysts on liquid-phase aerobic glycerol oxidation in water

Low-loaded Au–Fe and Au–Cu supported bimetallic catalysts showed exceptional activity in liquid-phase glycerol oxidation. Strong synergetic effect of Au–Fe (Cu) interaction and Au content tuned the oxidation activity and selectivity of the catalysts.

Understanding the opportunities of metal–organic frameworks (MOFs) for CO2 capture and gas-phase CO2 conversion processes: a comprehensive overview

The rapid increase in the concentration of atmospheric carbon dioxide is one of the most pressing problems facing our planet.

Recent advances in sustainable organic transformations using methanol: expanding the scope of hydrogen-borrowing catalysis

Recent progress relating to sustainable approaches using methanol as a C1-alkylating agent for C–Me and N–Me bond formation is discussed.

Selective Synthesis of Benzimidazoles from o-Phenylenediamine and Aldehydes Promoted by Supported Gold Nanoparticles

We investigated the catalytic efficacy of supported gold nanoparticles (AuNPs) towards the selective reaction between o-phenylenediamine and aldehydes that yields 2-substituted benzimidazoles. Among several supported gold nanoparticle platforms, the Au/TiO₂ provides a series of 2-aryl and 2-alkyl substituted benzimidazoles at ambient conditions, in the absence of additives and in high yields, using the mixture CHCl₃:MeOH in ratio 3:1 as the reaction solvent. Among the AuNPs catalysts used herein, the Au/TiO₂ containing small-size nanoparticles is found to be the most active towards the present catalytic methodology. The Au/TiO₂ can be recovered and reused at least five times without a significant loss of its catalytic efficacy. The present catalytic synthetic protocol applies to a broad substrate scope and represents an efficient method for the formation of a C–N bond under mild reaction conditions. Notably, this catalytic methodology provides the regio-isomer of the anthelmintic drug, Thiabendazole, in a lab-scale showing its applicability in the efficient synthesis of such N-heterocyclic molecules at industrial levels.

Influencing the Electron Density of Nanosized Au Colloids via Immobilization on MgO to Stimulate Surface Reaction Activities

Heterogenization of colloidal gold on MgO is demonstrated to facilitate its catalytic surface reactivity. We show that the electron density on Au influenced by its immobilization on MgO along with the ensued metal-support interaction is one of the key parameters to obtain high activity. As elucidated by X-ray absorption spectroscopic (X-ray photoelectron spectroscopy, X-ray absorption near-edge structure, and extended X-ray absorption fine structure) studies, the presence of well-dispersed nanosized Au on MgO is observed to result in an enhancement in the electron density of Au. The consequence of this electron-rich gold on the catalytic activity is then investigated using the nitroarene reduction as a model reaction with a detailed kinetic study. The kinetic study is an attempt to use a true heterogeneous system rather than the usually studied quasi-homogeneous systems. The results obtained reveal that the Au/MgO catalyst has a surface rate constant of ∼1.39 × 10^-3 mol m^-2 s^-1, which is significantly higher than those of the reported catalysts. While it validates the higher catalytic activity with a TOF of 9456 h^-1 observed for Au/MgO, the increased adsorption constant for 4-nitrophenol on Au/MgO further reflects the efficacy of MgO as the support. This not only allows effective heterogenization of the Au nanoparticles keeping the catalyst stable under the reaction conditions and being reused several times but also renders a capability in reduction of other nitro group-containing substrates. Therefore, the results are believed to be of importance in designing heterogeneous catalysts utilizing the distinctive properties of the nanosized colloids and tuning their surface reactivity as well.

Power of Aerogel Platforms to Explore Mesoscale Transport in Catalysis

We describe the opportunity to deploy aerogels-an ultraporous nanoarchitecture with co-continuous networks of meso/macropores and covalently bonded nanoparticulates-as a platform to address the nature of the electronic, ionic, and mass transport that underlies catalytic activity. As a test case, we fabricated Au||TiO₂ junctions in composite guest-host aerogels in which ∼5 nm Au nanoparticles are incorporated either directly into the anatase TiO₂ network (Au "in" TiO₂, Au_IN-TiO₂ aerogel) or deposited onto preformed TiO₂ aerogel (Au "on" TiO₂, Au_ON/TiO₂ aerogel). The metal-meets-oxide nanoscale interphase as visualized by electron tomography feature extended three-dimensional (3D) interfaces, but Au_IN-TiO₂ aerogels impose a greater degree of Au contact with TiO₂ particles than does the Au_ON/TiO₂ form. Both aerogel variants enable transport of electrons over micrometer-scale distances across the TiO₂ network to Au||TiO₂ junctions, as evidenced by electron paramagnetic resonance (EPR) and ultrafast visible pump-IR probe time-resolved absorption spectroscopy. The siting of gold nanoparticles in the TiO₂ network more effectively disperses trapped electrons. Density functional theory (DFT) calculations find that increased physical contact between Au and TiO₂, induced by oxygen vacancies, produces increased hybridization of midgap states and quenches unpaired trapped electrons. We assign the apparent differences in electron-transport capabilities to a combination of the relatively better-wired Au||TiO₂ junctions in Au_IN-TiO₂ aerogels, which have a greater capacity to dilute accumulated charge over a larger interfacial surface area, with an enhanced ability to discharge the accumulated electrons via catalytic reduction of adsorbed O₂ to O^2- at the interface. Solid-state ¹H nuclear magnetic resonance experiments show that proton spin-lattice relaxation times and possibly proton diffusion are strongly coupled to Au||TiO₂ interfacial design, likely through spin coupling of protons to unpaired electrons trapped at the TiO₂ network. Taken together, our results show that Au||TiO₂ interfacial design strongly impacts charge carrier (electron and proton) transport over mesoscale distances in catalytic aerogel architectures.

Unusual behavior of bimetallic nanoparticles in catalytic processes of hydrogenation and selective oxidation

Recent results obtained in studying mono- and bimetallic catalysts for selective hydrogenation of unsaturated carbonyl compounds, even unsaturated ones, acetylenic and nitro compounds as well as CO and bio-available alcohols oxidation are reviewed from the standpoint of the strong interaction between the metal nanoparticles, on the one hand, and two metals in the composition of bimetallic nanoparticles, on the other hand. Such interactions were demonstrated to result in partial positive or negative charging of metal nanoparticles, which, in turn, changes their adsorption and catalytic properties, especially with respect to the reactions involving hydrogen. Among the systems studied, Au–Pt, Au–Pd, Au–Cu, Au–Fe, Pt–WO x , Fe–Pd, Fe–Pt, Fe–Cu nanoparticles prepared by the redox procedure are considered to be most perspective in diverse catalytic applications because of the proper combination of the particle size and the electronic state of the metals.

β-Borylation of conjugated carbonyl compounds with silylborane or bis(pinacolato)diboron catalyzed by Au nanoparticles

β-Borylation occurs in the Au/TiO₂-catalysed reaction between the silylborane Me₂PhSiBpin and conjugated carbonyl compounds, in contrast to the so far known analogous reaction catalysed by other metals, where β-silylation occurs instead.

Gold-Catalyzed Cross-Coupling Reactions: An Overview of Design Strategies, Mechanistic Studies, and Applications

Transition-metal-catalyzed cross-coupling reactions are central to many organic synthesis methodologies. Traditionally, Pd, Ni, Cu, and Fe catalysts are used to promote these reactions. Recently, many studies have showed that both homogeneous and heterogeneous Au catalysts can be used for activating selective cross-coupling reactions. Here, an overview of the past studies, current trends, and future directions in the field of gold-catalyzed coupling reactions is presented. Design strategies to accomplish selective homocoupling and cross-coupling reactions under both homogeneous and heterogeneous conditions, computational and experimental mechanistic studies, and their applications in diverse fields are critically reviewed. Specific topics covered are: oxidant-assisted and oxidant-free reactions; strain-assisted reactions; dual Au and photoredox catalysis; bimetallic synergistic reactions; mechanisms of reductive elimination processes; enzyme-mimicking Au chemistry; cluster and surface reactions; and plasmonic catalysis. In the relevant sections, theoretical and computational studies of Au^I /Au^III chemistry are discussed and the predictions from the calculations are compared with the experimental observations to derive useful design strategies.

Mechanistic insight into novel sulfoxide containing SABRE polarisation transfer catalysts

Signal Amplification By Reversible Exchange (SABRE) is a hyperpolarisation technique that commonly uses [Ir(H)2(carbene)(substrate)3]Cl complexes to catalytically transfer magnetisation from para-hydrogen derived hydride ligands to coordinated substrates. Here, we explore the reactivity of a novel class of such catalysts based on sulfoxide containing [IrCl(H)2(carbene)(DMSO)2], which are involved in the hyperpolarisation of pyruvate using SABRE. We probe the reactivity of this species by NMR and DFT and upon reaction with sodium pyruvate establish the formation of two isomers of [Ir(H)2(η2-pyruvate)(DMSO)(IMes)]. Studies with related disodium oxalate yield [Ir2(H)4(IMes)2(DMSO)2(η2-κ2-Oxalate)] that is characterised by NMR and X-ray diffraction.

Synthesis of Z-Enamides through Heterogeneous Gold-Catalyzed Stereoselective Hydrogenation of Ynamides

A facile synthesis of Z-enamides via heterogeneous Au/TiO₂ catalyzed stereoselective hydrogenation of ynamides has been developed. Easy to handle and inexpensive ammonium formate was used as the hydrogen source, and Z-enamides were formed in a highly stereoselective manner. The commercially available gold nanoparticle catalyst could be recycled multiple times without a significant loss of activity.

Supercritical water assisted preparation of recyclable gold nanoparticles and their catalytic utility in cross-coupling reactions under sustainable conditions

Preparation of gold nanoparticles (AuNPs) in environmentally friendly water without using any reducing agents under supercritical conditions is demonstrated. PXRD, XPS, FE-SEM and HR-TEM analysis confirmed the formation of phase-pure and crystalline AuNPs of the size of ∼10-30 nm. The catalytic potential of AuNPs was manifested through a generalized green procedure that could accommodate both Sonogashira as well as Suzuki coupling under aqueous conditions at low catalytic loading (0.1 mol%). The AuNP catalyst was found to be recuperated after the reaction and reused for up to six catalytic cycles with no leaching out of gold species as confirmed through ICP-OES analysis. With no confinement of AuNP catalysis to cross-coupling reaction, synthetic extension to one-flask preparation of π-conjugated semiconductors (4 examples) and their optoelectronic properties were also investigated. Other significant features of the present work include short reaction time, site-selectivity, wide substrate scope, high conversion, good chemical yields and applicability in gram-scale synthesis. Overall, the results of this paper signify an operationally sustainable supercritical fluid processing method for the synthesis of AuNPs and their catalytic application towards cross-coupling reactions in green media.

Nanometric NaYF4 as an Unconventional Support for Gold Catalysts for Oxidation Reactions

The metal-support interaction plays an important role in gold catalysis. We employ here crystalline cubic (α-) and hexagonal (β-) phases of heterometallic fluoride NaYF₄ nanoparticles (NPs), obtained by the decomposition of a single source precursor [NaY(TFA)₄(diglyme)] (TFA = trifluoroacetate), as nonoxide supports for gold catalysts. Using an isostructural gadolinium analogue, we also obtained doped α-NaYF₄:Gd³⁺ and β-NaYF₄:Gd³⁺ NPs. A successful deposition of ∼1% by weight gold NPs of average size 5-6.5 nm on these doped and undoped metal fluorides using HAuCl₄·3H₂O afforded Au/NaYF₄ catalysts which were thoroughly characterized by using several physicochemical techniques such as X-ray diffraction, Brunauer-Emmett-Teller analysis, high-resolution transmission electron microscopy, energy-dispersive X-ray spectrometry, and X-ray photoelectron spectroscopy. A comparative study of the above catalysts for different oxidation reactions show that while for the aerobic oxidation of trans-stilbene in solution phase, they are either better (in terms of stilbene conversion) or at par (in terms of trans-stilbene oxide yield) in comparison to the reference catalyst Au/TiO₂ of the World Gold Council, their activity toward CO oxidation reactions in gas phase remains much less than that of gold catalysts supported on metal oxides.

A Study of Catalytic Oxidation of a Library of C₂ to C₄ Alcohols in the Presence of Nanogold

The classical stoichiometric oxidation of alcohols is an important tool in contemporary organic chemistry. However, it still requires huge modifications in order to comply with the principles of green chemistry. The use of toxic chemicals, hazardous organic solvents, and the large amounts of toxic wastes that result from the reactions are a few examples of the problems that must be solved. Nanogold alone or conjugated with palladium were supported on different carriers (SiO₂, C) and investigated in order to evaluate their catalytic potential for environmentally friendly alcohol oxidation under solvent-free and base-free conditions in the presence H₂O₂ as a clean oxidant. We tested different levels of Au loading (0.1⁻1.2% wt.) and different active catalytic site forms (monometallic Au or bimetallic Au⁻Pd sites). This provided new insights on how the structure of the Au-dispersions affected their catalytic performance. Importantly, the examination of the catalytic performance of the resulting catalysts was oriented toward a broad scope of alcohols, including those that are the most resistant to oxidation-the primary aliphatic alcohols. Surprisingly, the studies proved that Au/SiO₂ at a level of Au loading as low as 0.1% wt. appeared to be efficient and prospective catalytic system for the green oxidation of alcohol. Most importantly, the results revealed that 0.1% Au/SiO₂ might be the catalyst of choice with a wide scope of utility in the green oxidation of various structurally different alcohols as well as the non-activated aliphatic ones.

High-Performance Synthesis of Phosphorus-Doped Graphene Materials and Stabilization of Phosphoric Micro- and Nanodroplets

A thermally induced cascade process leading to the formation of stable micro- and nanometer-size phosphoric droplets was developed starting from a molecular precursor. Microwave-induced pyrolysis of 1,2,3,4,5-pentaphenylphosphole oxide proceeded through a series of subsequent transformations involving formation of phosphorus-doped graphene oxide layers, seeding of carbon surface with phosphorus centers, and assembling of stable droplets. A complex nanostructured organization of the material was established in a remarkably short time of 3 min, and the process was performed in a thermally induced manner using microwave irradiation. High stability of the liquid phosphoric structures on the surface of doped graphene oxide over a few-month period was demonstrated, as well as under challenging conditions in organic solvents (chloroform, methylene chloride, or toluene media) and even under sonication. Detailed examination of this material by electron microscopy and a number of analytical methods showed its unique organization at the nanoscale, whereas computational modeling revealed unusually strong binding of phosphorus oxide P₄O₁₀ to the graphene surface. The study demonstrates a fascinating opportunity to access a complex nanostructured multicomponent material from a single and easily available molecular precursor.

Application of Silver Nanoparticles in the Multicomponent Reaction Domain: A Combined Catalytic Reduction Methodology to Efficiently Access Potential Hypertension or Inflammation Inhibitors

The catalytic efficacy of silver nanoparticles was investigated toward the chemoselective reduction of nitro-tetrazole or amino acid-substituted derivatives into the corresponding amines in high isolated yields. This highly efficient protocol was thereafter applied toward the multicomponent reaction synthesis of heterocyclic dihydroquinoxalin-2-ones with high isolated yields. The reaction proceeds with low catalyst loading (0.8-1.4 mol %) and under mild catalytic conditions, a very good functional-group tolerance, and high yields and can be easily scaled up to more than 1 mmol of product. Thus, the present catalytic methodology highlights a useful synthetic application. Different molecules are designed and accordingly synthesized with the current protocol that could play the role of inhibitors of the soluble epoxide hydrolase, an important target for therapies against hypertension or inflammation.

A quantification scheme for non-covalent interactions in the enantio-controlling transition states in asymmetric catalysis

The origin of enantioselectivity in asymmetric catalysis is attributed to the energy difference between lower and higher energy diastereomeric transition states, which are respectively responsible for the formation of major and minor enantiomers. Although the increase in the number of transition state models emphasizes the role of weak non-covalent interactions in asymmetric induction, the strength of such interactions is seldom quantified. Through this article, we propose a simple and effective method of quantifying the total non-covalent interaction in stereocontrolling transition states belonging to a group of three representative asymmetric catalytic reactions involving chiral phosphoric acids. Our method relies on rational partitioning of a given transition state into two (or three) sub-units, such that the complex network of intramolecular interactions can be ameliorated to a set of intermolecular interactions between two sub-units. The computed strength of interaction obtained using the counterpoise (CP) method on suitably partitioned transition states provides improved estimates of non-covalent interactions, which are also devoid of basis set superposition error (BSSE). It has been noted that catalysts decorated with larger aromatic arms provide cumulative non-covalent interactions (C-Hπ, N-Hπ and ππ) to the tune of 10 to 15 kcal mol-1. Fine-tuning of the magnitude and nature of these interactions can provide valuable avenues in the design of asymmetric catalysts.

Dual effects of water vapor on ceria-supported gold clusters

Atomically precise nanocatalysts are currently being intensely pursued in catalysis research. Such nanocatalysts can serve as model catalysts for gaining fundamental insights into catalytic processes. In this work we report a discovery that water vapor provokes the mild removal of surface long-chain ligands on 25-atom Au25(SC12H25)18 nanoclusters in a controlled manner. Using the resultant Au25(SC12H25)18-x/CeO2 catalyst and CO oxidation as a probe reaction, we found that the catalytic activity of cluster/CeO2 is enhanced from nearly zero conversion of CO (in the absence of water) to 96.2% (in the presence of 2.3 vol% H2O) at the same temperature (100 °C). The cluster catalysts exhibit high stability during the CO oxidation process under moisture conditions (up to 20 vol% water vapor). Water vapor plays a dual role in gold cluster-catalyzed CO oxidation. FT-IR and XPS analyses in combination with density functional theory (DFT) simulations suggest that the "-SC12H25" ligands are easier to be removed under a water vapor atmosphere, thus generating highly active sites. Moreover, the O22- peroxide species constitutes the active oxygen species in CO oxidation, evidenced by Raman spectroscopy analysis and isotope experiments on the CeO2 and cluster/CeO2. The results also indicate the perimeter sites of the interface of Au25(SC12H25)18-x/CeO2 to be active sites for catalytic CO oxidation. The controlled exposure of active sites under mild conditions is of critical importance for the utilization of clusters in catalysis.

Towards Sustainable Production of Formic Acid

Formic acid is a widely used commodity chemical. It can be used as a safe, easily handled, and transported source of hydrogen or carbon monoxide for different reactions, including those producing fuels. The review includes historical aspects of formic acid production. It briefly analyzes production based on traditional sources, such as carbon monoxide, methanol, and methane. However, the main emphasis is on the sustainable production of formic acid from biomass and biomass-derived products through hydrolysis and oxidation processes. New strategies of low-temperature synthesis from biomass may lead to the utilization of formic acid for the production of fuel additives, such as methanol; upgraded bio-oil; γ-valerolactone and its derivatives; and synthesis gas used for the Fischer-Tropsch synthesis of hydrocarbons. Some technological aspects are also considered.

Preparation and use of DMF-stabilized iridium nanoclusters as methylation catalysts using methanol as the C1 source

We report methylations of alcohols and anilines catalyzed by DMF-stabilized Ir nanoclusters using methanol as the C1 source. The DMF-stabilized Ir nanoclusters were prepared in one step and have diameters of 1-1.5 nm. They react in a borrowing-hydrogen reaction and are efficient methylation catalysts (TON up to 310 000).