Liquid Crystalline Phase and Gel−Sol Transitions for Concentrated Microcrystalline Cellulose (MCC)/1-Ethyl-3-methylimidazolium Acetate (EMIMAc) Solutions

Scaling Laws in Polysaccharide Rheology: Comparative Analysis of Water and Ionic Liquid Systems

This study investigates the rheological behavior of two plant-based polysaccharides, with different degrees of hydrophilicity, agar (highly hydrophilic) and guar gum (hydrophilic), in water and 1-ethyl-3-methylimidazolium acetate (EMImAc). The rheological response of these polymers is highly dependent on the solvent's ability to disrupt intermolecular associations. In water, agar forms hydrogels, while guar gum behaves as a viscoelastic liquid with slow modes. The plateau modulus (GN0) scales with polymer concentration (c) as GN0 ∼ c3, consistent with other natural polymers. In EMImAc, both polysaccharides form viscoelastic liquids, exhibiting GN0 ∼ c2.3, as expected for semiflexible polymer solutions. However, the terminal relaxation time, τD, and the specific viscosity, ηsp, scale as τD ∼ c5.3 and ηsp ∼ c7.6, indicative of intermolecular chain-chain associations. Despite the solvent or polysaccharide, the fractional viscosity overshoot and the shear strain at the maximum stress show a terminal Weissenberg number dependence similar to other synthetic polymers.

Revolutionizing lignocellulosic biomass: A review of harnessing the power of ionic liquids for sustainable utilization and extraction

The potential for the transformation of lignocellulosic biomass into valuable commodities is rapidly growing through an environmentally sustainable approach to harness its abundance, cost-effectiveness, biodegradability, and environmentally friendly nature. Ionic liquids (ILs) have received considerable and widespread attention as a promising solution for efficiently dissolving lignocellulosic biomass. The fact that ILs can act as solvents and reagents contributes to their widespread recognition. In particular, ILs are desirable because they are inert, non-toxic, non-flammable, miscible in water, recyclable, thermally and chemically stable, and have low melting points and outstanding ionic conductivity. With these characteristics, ILs can serve as a reliable replacement for traditional biomass conversion methods in various applications. Thus, this comprehensive analysis explores the conversion of lignocellulosic biomass using ILs, focusing on main components such as cellulose, hemicellulose, and lignin. In addition, the effect of multiple parameters on the separation of lignocellulosic biomass using ILs is discussed to emphasize their potential to produce high-value products from this abundant and renewable resource. This work contributes to the advancement of green technologies, offering a promising avenue for the future of biomass conversion and sustainable resource management.

Impact of coagulation solvent interactions on porous morphology evolution in cellulose xerogels

The role of coagulation solvent interactions on the pore formation mechanism in cellulose xerogels was investigated using single-step coagulation baths. A series of cellulose xerogels were fabricated from cotton yarns partially dissolved in ionic liquid (i.e., 1-ethyl-3-methylimidazolium acetate) and then immersed in one of seven different coagulation baths. These samples were evaluated using N2 physisorption, inverse gas chromatography, and X-ray photoelectron spectroscopy. The regenerated cellulose orientation and resultant surface hydrophilicity was found to be dependent on solvent solubility interactions with an emphasis on polar interaction and dispersion force strength. More importantly, the xerogel specific surface area dramatically decreased from 100 m2g-1 to 0.278 m2g-1 with increasing hydrophilicity, confirming the importance of controlled cellulose orientation during the coagulation step of cellulose xerogel fabrication. These results have been used to propose a new pore formation mechanism in cellulose xerogels and provide recommendations towards the development of controllable porosity during xerogel fabrication.

Stretch-Induced Crystallization of Cellulose Spun from Ionic Liquid Solution

With the emergence of efficient green solvents, structural regulation of regenerated cellulose is highly desired in the solution process from an industrial perspective. Cellulose fiber and films are viewed as a "composite" comprising amorphous and crystalline fractions. The regulation of the crystalline structure is of great importance for the properties of cellulose materials. In this study, we found stretch-induced crystallization behavior during the transition from solution to gel via coagulation. The crystallinity index of the hydrogel fiber increases with the stretch ratio (SR). X-ray diffraction revealed that the cellulose II hydrate formed in the stretched hydrogel fibers. The mechanical properties and thermal stability of the dry fibers greatly improved against the SR. This crystallization behavior depends on the concentration of the solution and the type of ionic liquid. This stretch-induced crystallization provides an efficient method for structural regulation in cellulose solution processing.

Thermo-reversible cellulose micro phase-separation in mixtures of methyltributylphosphonium acetate and γ-valerolactone or DMSO

We have identified cellulose solvents, comprised of binary mixtures of molecular solvents and ionic liquids that rapidly dissolve cellulose to high concentration and show upper‐critical solution temperature (UCST)‐like thermodynamic behaviour ‐ upon cooling and micro phase‐separation to roughly spherical microparticle particle‐gel mixtures. This is a result of an entropy‐dominant process, controllable by changing temperature, with an overall exothermic regeneration step. However, the initial dissolution of cellulose in this system, from the majority cellulose I allomorph upon increasing temperature, is also exothermic. The mixtures essentially act as ‘thermo‐switchable’ gels. Upon initial dissolution and cooling, micro‐scaled spherical particles are formed, the formation onset and size of which are dependent on the presence of traces of water. Wide‐angle X‐ray scattering (WAXS) and ¹³C cross‐polarisation magic‐angle spinning (CP‐MAS) NMR spectroscopy have identified that the cellulose micro phase‐separates with no remaining cellulose I allomorph and eventually forms a proportion of the cellulose II allomorph after water washing and drying. The rheological properties of these solutions demonstrate the possibility of a new type of cellulose processing, whereby morphology can be influenced by changing temperature.

Smart/stimuli-responsive hydrogels: Cutting-edge platforms for tissue engineering and other biomedical applications

Recently, biomedicine and tissue regeneration have emerged as great advances that impacted the spectrum of healthcare. This left the door open for further improvement of their applications to revitalize the impaired tissues. Hence, restoring their functions. The implementation of therapeutic protocols that merge biomimetic scaffolds, bioactive molecules, and cells plays a pivotal role in this track. Smart/stimuli-responsive hydrogels are remarkable three-dimensional (3D) bioscaffolds intended for tissue engineering and other biomedical purposes. They can simulate the physicochemical, mechanical, and biological characters of the innate tissues. Also, they provide the aqueous conditions for cell growth, support 3D conformation, provide mechanical stability for the cells, and serve as potent delivery matrices for bioactive molecules. Many natural and artificial polymers were broadly utilized to design these intelligent platforms with novel advanced characteristics and tailored functionalities that fit such applications. In the present review, we highlighted the different types of smart/stimuli-responsive hydrogels with emphasis on their synthesis scheme. Besides, the mechanisms of their responsiveness to different stimuli were elaborated. Their potential for tissue engineering applications was discussed. Furthermore, their exploitation in other biomedical applications as targeted drug delivery, smart biosensors, actuators, 3D and 4D printing, and 3D cell culture were outlined. In addition, we threw light on smart self-healing hydrogels and their applications in biomedicine. Eventually, we presented their future perceptions in biomedical and tissue regeneration applications. Conclusively, current progress in the design of smart/stimuli-responsive hydrogels enhances their prospective to function as intelligent, and sophisticated systems in different biomedical applications.

Revisiting the dissolution of cellulose in H3PO4(aq) through cryo-TEM, PTssNMR and DWS

Cellulose can be dissolved in concentrated acidic aqueous solvents forming extremely viscous solutions, and, in some cases, liquid crystalline phases. In this work, the concentrated phosphoric acid aqueous solvent is revisited implementing a set of advanced techniques, such as cryo-transmission electronic microscopy (cryo-TEM), polarization transfer solid-state nuclear magnetic resonance (PTssNMR), and diffusing wave spectroscopy (DWS). Cryo-TEM images confirm that this solvent system is capable to efficiently dissolve cellulose. No cellulose particles, fibrils, or aggregates are visible. Conversely, PTssNMR revealed a dominant CP signal at 25 °C, characteristic of C-H bond reorientation with correlation time longer than 100 ns and/or order parameter above 0.5, which was ascribed to a transient gel-like network or an anisotropic liquid crystalline phase. Increasing the temperature leads to a gradual transition from CP to INEPT-dominant signal and a loss of birefringence in optical microscopy, suggesting an anisotropic-to-isotropic phase transition. Finally, an excellent agreement between optical microrheology and conventional mechanical rheometry was also obtained.

Partially Acetylated Cellulose Dissolved in Aqueous Solution: Physical Properties and Enzymatic Hydrolysis

Cellulose acetate is one of the most important cellulose derivatives. The use of ionic liquids in cellulose processing was recently found to act both as a solvent and also as a reagent. A recent study showed that cellulose dissolution in the ionic liquid 1-ethyl-3-methylimidazoliumacetate (EMIMAc) mixed with dichloromethane (DCM) resulted in controlled homogenous cellulose acetylation; yielding water-soluble cellulose acetate (WSCA). This research investigated the properties of cellulose acetate prepared in this manner, in an aqueous solution. The results revealed that WSCA fully dissolves in water, with no significant sign of molecular aggregation. Its conformation in aqueous solution exhibited a very large persistence length, estimated as over 10 nm. The WSCA exhibited surface activity, significantly reducing the surface tension of water. Because of the molecular dissolution of WSCA in water, augmented by its amphiphilicity, aqueous solutions of WSCA exhibited an overwhelmingly high rate of enzymatic hydrolysis.

Unique gelation and rheological properties of the cellulose/CO2-based reversible ionic liquid/DMSO solutions

Gelation and rheological behaviors of cellulose/CO₂-based reversible ionic liquid (RIL)/DMSO solutions were investigated. The exponents of specific viscosity η_sp versus concentration c were determined for wood pulp (WP) and microcrystalline cellulose (MCC) solutions. The complex viscosity acquired using oscillatory shear closely follows the steady shear viscosity, thus revealing the applicability of Cox-Merz rule. The influence of RIL content in the solvent on apparent viscosities, activation energy, intrinsic viscosities, specific viscosity-c[η] master curve, and relaxation time were also investigated. Gelation occurred in this cellulose solution system due to thermal-induced CO₂ release from the decomposition of the CO₂-based reversible ionic liquid. The formed gel was stable in air, but re-dissolved when exposed to CO₂, indicating the switch-on and switch-off effects of CO₂ in cellulose dissolution and gelation.

Colloidal Particle-Induced Microstructural Transition in Cellulose/Ionic Liquid/Water Mixtures

The role of colloidal particles in enhancing the mechanical and thermal properties of liquid crystalline (LC) gels formed in microcrystalline cellulose/1-allyl-3-methylimidazolium chloride/water mixtures is experimentally investigated by means of rheology and polarized optical microscopy (POM). The overshoot in loss modulus and increase in the melting temperature of LC domains as observed in differential scanning calorimetry signal a stronger interaction of cellulose with both hydrophobic polystyrene and hydrophilic silica nanoparticles which in turn point to considerable amphiphilic nature of cellulose. The aggregation of nanoparticles observed by POM and the rheological behavior point to the development of a sample-spanning network of cellulose-nanoparticle clusters during the sol-gel transition with an increase in concentration of water. Furthermore, the LC gels obey Chambon-Winter (CW) criterion, indicating a self-similar gel network, except at very high particle loadings. Moreover, the LC domains show a temporal evolution into a space-spanning network of cellulose spherulites. The evolution process largely depends on the particle concentration, with highly loaded samples showing quicker evolution, which leads to a violation of the CW criterion. Furthermore, the temperature-induced microstructural transition (with and without shear) is also examined.

Rheology and microstructure of concentrated microcrystalline cellulose (MCC)/1-allyl-3-methylimidazolium chloride (AmimCl)/water mixtures

Water added to a solution of microcrystalline cellulose (MCC) in 1-allyl-3-methylimidazolium chloride (AmimCl) reduces the solvent quality and causes significant changes in the flow properties and microstructure due to restructuring and aggregation of cellulose molecules. We report an experimental investigation by means of polarization optical microscopy (POM) and rheology of the distinct phases formed in 5-20 wt% MCC/AmimCl solutions due to the addition of water. With increase in the cellulose concentration, the MCC/AmimCl/water mixtures showed different morphologies such as the non-aligned cholesteric liquid crystalline (LC) domain, the coexistence of spherulite-like structures within the LC domain and a space-spanning network of spherulite-like structures at high concentrations of water. In situ microscopy during shear and POM observations pre and post shear revealed a significant increase in the size of the birefringent domains as the shear rate is increased, which continued to exist even after the cessation of shear. With an increase in the concentration of water, the zero shear viscosity of the MCC/AmimCl/water mixtures was found to go through a minimum, beyond which the aggregation of cellulose commenced. The corresponding oscillatory shear response showed a sol-gel transition with an increase in water concentration. Moreover, at high cellulose concentrations (12-20 wt%), the MCC/AmimCl/water gels exhibited self-similarity and followed the Chambon-Winter (CW) criterion. The similar phase behavior and rheological response observed for MCC dissolved in 1-butyl-3 methylimidazolium chloride (BmimCl) indicated the generality of the presented results.

Improving Cellulose Dissolution in Ionic Liquids by Tuning the Size of the Ions: Impact of the Length of the Alkyl Chains in Tetraalkylammonium Carboxylate

Twenty ionic liquids based on tetraalkylammonium cations and carboxylate anions have been synthesized, characterized, and tested for cellulose dissolution. The amount of cellulose dissolved in these ionic liquids depends strongly on the size of the ions: from 0 to 22 wt % cellulose can be dissolved at 90 °C. The best ionic liquids are less viscous and ammonium carboxylate based ionic liquids can dissolve as much as imidazolium-based ones. The viscosity of an ionic liquid can be decreased by the addition of DMSO as a cosolvent. After the addition of cosolvent, similar amounts of cellulose per ions are reached for most ionic liquids. As observed by rheology, ionic liquids with the longest alkyl chains form a gel when a high amount of cellulose is dissolved; this drastically limits their potential. Molecular simulations and IR spectroscopy have also been used with the aim of understanding how molecular interactions differ between efficient and inefficient ionic liquids.

Anion Bridging-Induced Structural Transformation of Cellulose Dissolved in Ionic Liquid

We performed structural investigations of cellulose mixed with 1-ethyl-3-methylimidazolium acetate ([Emim][OAc]) in the entire concentration range (0-100 mol %) by wide-angle X-ray scattering with the aid of quantum chemical calculations and ¹³C solid-state NMR spectroscopy. We particularly focused on a highly concentrated region (≥30 mol %), which has previously been overlooked. At concentrations of 15-30 mol %, a periodic peak corresponding to cellulose chain alignment emerged; this is associated with a lyotropic cholesteric liquid-crystalline phase. At concentrations of ≥30 mol %, the structure is transformed into ordered layers where OAc anions and Emim cations intercalate. This transformation is found to be driven by a change in the interaction between the IL anions and the OH groups of cellulose. At low concentrations, the anion mainly interacts with the OH group of cellulose in a 1:1 ratio, as previously reported; at high concentrations, the anions bridge the OH groups of two cellulose chains.

Physical state of cellulose in BmimCl: dependence of molar mass on viscoelasticity and sol-gel transition

Monitoring cellulose depolymerization and phase transition in ionic liquid.

Synthesis and characterization of bicontinuous cubic poly(3,4-ethylene dioxythiophene) gyroid (PEDOT GYR) gels

We describe the synthesis and characterization of bicontinuous cubic poly(3,4-ethylenedioxythiophene) (PEDOT) conducting polymer gels prepared within lyotropic cubic poly(oxyethylene)10 nonylphenol ether (NP-10) templates with Ia3[combining macron]d (gyroid, GYR) symmetry. The chemical polymerization of EDOT monomer in the hydrophobic channels of the NP-10 GYR phase was initiated by AgNO3, a mild oxidant that is activated when exposed to ultraviolet (UV) radiation. The morphology and physical properties of the resulting PEDOT gels were examined as a function of temperature and frequency using optical and electron microscopy, small-angle X-ray scattering (SAXS), dynamic mechanical spectroscopy, and electrochemical impedance spectroscopy (EIS). Microscopy and SAXS results showed that the PEDOT gels remained ordered and stable after the UV-initiated chemical polymerization, confirming the successful templated-synthesis of PEDOT in bicontinuous GYR nanostructures. In comparison to unpolymerized 3,4-ethylenedioxythiophene (EDOT) gel phases, the PEDOT structures had a higher storage modulus, presumably due to the formation of semi-rigid PEDOT-rich nanochannels. Additionally, the storage modulus (G') for PEDOT gels decreased only modestly with increasing temperature, from ∼1.2 × 10(5) Pa (10 °C) to ∼7 × 10(4) Pa (40 °C), whereas G' for the NP-10 and EDOT gels decreased dramatically, from ∼5.0 × 10(4) Pa (10 °C) to ∼1.5 × 10(2) Pa (40 °C). EIS revealed that the impedance of the PEDOT gels was smaller than the impedance of EDOT gels at both high frequencies (PEDOT ∼10(2) Ω and EDOT 2-3 × 10(4) Ω at 10(5) Hz) and low frequencies (PEDOT 10(3)-10(5) Ω and EDOT ∼5 × 10(5) Ω at 10(-1) Hz). These results indicated that PEDOT gels were highly ordered, mechanically stable and electrically conductive, and thus should be of interest for applications for which such properties are important, including low impedance and compliant coatings for biomedical electrodes.

Effect of dimethylsulfoxide on the viscoelastic properties and sol–gel transition of cellulose/ionic liquid solutions

Viscoelastic properties of cellulose solutions with 1-butyl-3-methylimidazolium chloride ([BMIM]Cl) and dimethylsulfoxide (DMSO) as solvents were studied by rheological experiments.

From cellulose fibrils to single chains: understanding cellulose dissolution in ionic liquids

Continued improvement on the structure of elementary fibrils, simulation of larger elementary fibrils and systematic work on the solution structure of cellulose in ILs are three interacting modules to unravel the mechanism of cellulose dissolution in ILs.

Amphiphilic and phase-separable ionic liquids for biomass processing

One main limiting factor for the technoeconomics of future bioprocesses that use ionic liquids (ILs) is the recovery of the expensive and potentially toxic IL. We have demonstrated a new series of phase-separable ionic liquids, based on the hydrophobic tetraalkylphosphonium cation ([PRRRR](+)), that can dissolve lignin in the neat state but also hemicellulose and high-purity cellulose in the form of their electrolyte solutions with dipolar aprotic solvents. For example, the IL trioctylmethylphosphonium acetate ([P8881][OAc]) was demonstrated to dissolve up to 19 wt % of microcrystalline cellulose (MCC) at 60 °C with the addition of 40 wt % of DMSO. It was found that the MCC saturation point is dependent on the molar ratio of DMSO and IL in solution. At the optimum saturation, a ∼1:1 molar ratio of [P8881][OAc] to anhydroglucose units is observed, which demonstrates highly efficient solvation. This is attributed to the positive contribution that these more amphiphilic cation-anion pairs provide, in the context of the Lindman hypothesis. This effective dissolution is further illustrated by solution-state HSQC NMR spectroscopy on MCC. Finally, it is also demonstrated that these electrolytes are phase separable by the addition of aqueous solutions. The addition of 10 % NaOAc solution allows a near quantitative recovery of high-purity [P8881][OAc]. However, increased volumes of aqueous solution reduced the recovery. The regenerated material was found to partially convert into the cellulose II crystalline polymorph.

Liquid crystalline phase behavior and sol-gel transition in aqueous halloysite nanotube dispersions

The liquid crystalline phase behavior and sol-gel transition in halloysite nanotubes (HNTs) aqueous dispersions have been investigated by applying polarized optical microscopy (POM), macroscopic observation, rheometer, small-angle X-ray scattering, scanning electron microscopy, and transmission electron microscopy. The liquid crystalline phase starts to form at the HNT concentration of 1 wt %, and a full liquid crystalline phase forms at the HNT concentration of 25 wt % as observed by POM and macroscopic observation. Rheological measurements indicate a typical shear flow behavior for the HNT aqueous dispersions with concentrations above 20 wt % and further confirm that the sol-gel transition occurs at the HNT concentration of 37 wt %. Furthermore, the HNT aqueous dispersions exhibit pH-induced gelation with more intense birefringence when hydrochloric acid (HCl) is added. The above findings shed light on the phase behaviors of diversely topological HNTs and lay the foundation for fabrication of the long-range ordered nano-objects.

Preparation and characterization of bionanocomposite fiber based on cellulose and nano-SiO2 using ionic liquid

Microcrystalline cellulose (MCC)/nano-SiO2 composite fibers were processed from solutions in 1-allyl-3-methylimidazolium chloride (AMIMCl) by the method of dry-jet wet spinning. The oscillatory shear measurements demonstrated that the gel network formed above 10 wt% nano-SiO2 and the complex viscosity increased with increasing nano-SiO2. Remarkably, the shear viscosity of the nanofluids was even lower than solutions without nano-SiO2 under high shear rates. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) images revealed that well-dispersed particles exhibit strong interfacial interactions with cellulose matrix. Measurements on wide-angle X-ray diffraction (WAXD) indicated that the regenerated cellulose and nanocomposite fibers were the typical cellulose II crystalline form, which was different from the native cellulose with the polymorph of Type I. The tensile strength of the nanocomposite fibers was larger than that of pure cellulose fiber and showed a tendency to increase and then decrease with increasing nano-SiO2. Furthermore, the nanocomposite fibers exhibited improved thermal stability.

Shear and extensional rheology of cellulose/ionic liquid solutions

In this study, we characterize the shear and extensional rheology of dilute to semidilute solutions of cellulose in the ionic liquid 1-ethyl-3-methylimidazolium acetate (EMIAc). In steady shear flow, the semidilute solutions exhibit shear thinning, and the high-frequency complex modulus measured in small amplitude oscillatory shear flow exhibits the characteristic scaling expected for solutions of semiflexible chains. Flow curves of the steady shear viscosity plotted against shear rate closely follow the frequency dependence of the complex viscosity acquired using oscillatory shear, thus satisfying the empirical Cox-Merz rule. We use capillary thinning rheometry (CaBER) to characterize the relaxation times and apparent extensional viscosities of the semidilute cellulose solutions in a uniaxial extensional flow that mimics the dynamics encountered in the spin-line during fiber spinning processes. The apparent extensional viscosity and characteristic relaxation times of the semidilute cellulose/EMIAc solutions increase dramatically as the solutions enter the entangled concentration regime at which fiber spinning becomes viable.

Phase Analysis of the Cellulose Triacetate-Nitromethane System

A comprehensive study was made on the cellulose triacetate-nitromethane system to explore its phase separation within ranges 2–25 wt.% and−5÷+80°Cby means of polarization light and electron microscopy, the turbidity spectrum method, differential thermal and X-ray analyses, and rheological techniques. The physical state of the polymer was identified within the phase coexistence boundaries on the phase diagram which included three types of phase separation (amorphous (with a UCST atTcr=57∘Candccr=7.3 wt.%), crystal, and liquid crystal). The boundaries of the regions determining the coexistence of the liquid crystal (LC) and the partly crystal phase were found to be inside the region of amorphous liquid-liquid phase separation. For cellulose ester-solvent systems, this state diagram is the first experimental evidence for the possibility of coexistence of several phases with amorphous, LC, and crystal polymer ordering.