Ethanol Electro-Oxidation on Ternary Platinum–Rhodium–Tin Nanocatalysts: Insights in the Atomic 3D Structure of the Active Catalytic Phase

Electronic and Geometric Effects Endow PtRh Jagged Nanowires with Superior Ethanol Oxidation Catalysis

Complete ethanol oxidation reaction (EOR) in C1 pathway with 12 transferred electrons is highly desirable yet challenging in direct ethanol fuel cells. Herein, PtRh jagged nanowires synthesized via a simple wet-chemical approach exhibit exceptional EOR mass activity of 1.63 A mgPt-1 and specific activity of 4.07 mA cm-2 , 3.62-fold and 4.28-folds increments relative to Pt/C, respectively. High proportions of 69.33% and 73.42% of initial activity are also retained after chronoamperometric test (80 000 s) and 1500 consecutive potential cycles, respectively. More importantly, it is found that PtRh jagged nanowires possess superb anti-CO poisoning capability. Combining X-ray absorption spectroscopy, X-ray photoelectron spectroscopy as well as density functional theory calculations unveil that the remarkable catalytic activity and CO tolerance stem from both the Rh-induced electronic effect and geometric effect (manifested by shortened Pt─Pt bond length and shrinkage of lattice constants), which facilitates EOR catalysis in C1 pathway and improves reaction kinetics by reducing energy barriers of rate-determining steps (such as *CO → *COOH). The C1 pathway efficiency of PtRh jagged nanowires is further verified by the high intensity of CO2 relative to CH3 COOH/CH3 CHO in infrared reflection absorption spectroscopy.

Tuning Catalytic Activity in Ultrathin Bimetallic Nanowires via Surface Segregation: Some Insights

The efficiency of heterogeneous catalysts critically depends on the nature of the surface. We present results on controlling the composition in ultrathin bimetallic AuPd. AuPd wires were grown using Au nanowire templates; the surface composition could be tuned by increasing the amount of Pd. Further, segregation of Pd to the surface could be induced in alloyed nanowires by annealing under a controlled CO atmosphere. Electrocatalytic activity of these bimetallic systems is assessed for the methanol oxidation reaction (MOR). While the MOR potential shows a monotonic increase with Pd content, the specific activity displays a typical volcano-type behavior. The CO-annealed nanowires show a lowering of potential owing to a higher Pd content on the surface while still maintaining the specific activity. These findings provide clear strategies to independently control the reaction potential and the activities of nanocatalysts. The experimental findings are well supported by the theoretical investigations using density functional theory (DFT) calculations.

Insights into reaction mechanisms of ethanol electrooxidation at the Pt/Au(111) interfaces using density functional theory

Understanding ethanol electrooxidation reaction kinetics is fundamental to the development of direct ethanol fuel cells.

Controllable Synthesis of Platinum-Tin Intermetallic Nanoparticles with High Electrocatalytic Performance for Ethanol Oxidation

This article proposes a general approach for the preparation of intermetallic nanoparticles of Pt3Sn, PtSn, PtSn2, and PtSn4, triggered by hexamethyldisilazane (HMDS) in conjunction with SnCl2. The ethanol oxidation reaction...

Platinum-Tin/Tin Oxide/CNT Catalysts for High-Performance Electrocatalytic Ethanol Oxidation

Ethanol is a promising liquid clean energy source in the energy conversion field. However, the self-poisoning caused by the strongly adsorbed reaction intermediates (typically, CO) is a critical problem in ethanol oxidation reaction. To address this issue, we proposed a joint use of two strategies, alloying of Pt with other metals and building Pt/metal-oxide interfaces, to achieve high-performance electrocatalytic ethanol oxidation. For this, a well-designed synthetic route combining wet impregnation with a two-step thermal treatment process was established to construct PtSn/SnO_x interfaces on carbon nanotubes. Using this route, the alloying of Pt-Sn and formation of PtSn-SnO_x interfaces can simultaneously be achieved, and the coverage of SnO_x thin films on PtSn alloy nanoparticles can be facilely tuned by the strong interaction between Pt and SnO_x . The results revealed that the partial coverage of SnO_x species not only retained the active sites, but also enhanced the CO anti-poisoning ability of the catalyst. Consequently, the H-PtSn/SnO_x /CNT-2 catalyst with an optimized PtSn-SnO_x interface showed significantly improved performances toward the ethanol oxidation reaction (825 mA mg_Pt ^-1 ). This study provides deep insights into the structure-performance relationship of PtSn/metal oxide composite catalysts, which would be helpful for the future design and fabrication of high-performance Pt-based ethanol oxidation reaction catalysts.

An Overview of Glycerol Electrooxidation Mechanisms on Pt, Pd and Au

In the most recent decade, glycerol electrooxidation (GEOR) has attracted extensive research interest for valorization of glycerol: the conversion of glycerol to value-added products. These reactions at platinum, palladium, and gold electrodes have a lot of uncertainty in their reaction mechanisms, which has generated some controversies. This review gathers many reported experimental results, observations and proposed reaction mechanisms in order to draw a full picture of GEOR. A particular focus is the clarification of two propositions: Pd is inferior to Pt in cleaving the C-C bonds of glycerol during the electrooxidation and the massive production of CO₂ at high overpotentials is due to the oxidation of the already-oxidized carboxylate products. It is concluded that the inferior C-C bond cleavability with Pd electrodes, as compared with Pt electrodes, is due to the inefficiency of deprotonation, and the massive generation of CO₂ as well as other C1/C2 side products is partially caused by the consumption of OH^- at the anodes, as a lower pH reduces the amount of carboxylates and favors the C-C bond scission. A reaction mechanism is proposed in this review, in which the generation of side products are directly from glycerol ("competition" between each side product) rather than from the further oxidation of C2/C3 products. Additionally, GEOR results and associated interpretations for Ni electrodes are presented, as well as a brief review on the performances of multi-metallic electrocatalysts (most of which are nanocatalysts) as an introduction to these future research hotpots.

Highly Active Hollow RhCu Nanoboxes toward Ethylene Glycol Electrooxidation

The efficient electrocatalysts toward the ethylene glycol oxidation reaction (EGOR) are highly desirable for direct ethylene glycol fuel cells because of the sluggish kinetics of anodic EGOR. Herein, porous RhCu nanoboxes are successfully prepared through facile galvanic replacement reaction and succedent sodium borohydride reduction strategy. Benefiting from hierarchical pore structure, RhCu nanoboxes display excellent electrocatalytic performance toward the EGOR in alkaline medium with a mass activity of 775.1 A g_Rh ^-1 , which is 2.8 times as large as that of commercial Rh nanocrystals. Moreover, the long-term stability of RhCu nanoboxes is better than that of commercial Rh nanocrystals. Furthermore, the theoretical calculations demonstrate that RhCu nanoboxes possess lower adsorption energy of CO and lower reaction barrier (0.27 eV) for the CO_ads oxidation with aid of the adsorbed OH_ads species, resulting in the outstanding electrocatalytic performance toward the EGOR. This work provides a meaningful reference for developing highly effective electrocatalysts toward the EGOR.

Investigation of the thermal removal steps of capping agents in the synthesis of bimetallic iridium-based catalysts for the ethanol oxidation reaction

Two iridium-based catalysts (namely IrSn and IrNi) are synthesised via a polyol route involving capping agents.

Optimization of Pt-Oxygen-Containing Species Anodes for Ethanol Oxidation Reaction: High Performance of Pt-AuSnOx Electrocatalyst

Pt-oxygen-containing species (Pt-OCS) catalysts, in which OCS (e.g., metal-oxides) are decorated on a Pt surface, possess enhanced ethanol oxidation reaction (EOR) activity and stability compared with pure Pt and are promising in practical applications of direct ethanol fuel cells. We investigate the promotion roles of Pt-OCS electrocatalysts toward the EOR via a combination of density functional theory (DFT) calculations and experiments, providing a rational design strategy for Pt-OCS catalysts. It is revealed that Pt-AuO and Pt-SnO excel in EOR activity and stability, respectively, among the DFT screening of various Pt-OCS systems, and this is confirmed by the following experiments. Moreover, an optimized Pt-AuSnO catalyst is proposed by DFT calculations, taking advantage of both Pt-AuO and Pt-SnO. The as-prepared Pt-AuSnO catalyst delivers an EOR activity that is 9.7 times higher than that of Pt and shows desired stability. These findings are expected to elucidate the mechanistic insights into Pt-OCS materials and lead to advanced EOR electrocatalysts.

A review of recent progress on electrocatalysts toward efficient glycerol electrooxidation

Glycerol electrooxidation has attracted immense attention due to the economic advantage it could add to biodiesel production. One of the significant challenges for the industrial development of glycerol electrooxidation process is the search for a suitable electrocatalyst that is sustainable, cost effective, and tolerant to carbonaceous species, results in high performance, and is capable of replacing the conventional Pt/C catalyst. We review suitable, sustainable, and inexpensive alternative electrocatalysts with enhanced activity, selectivity, and durability, ensuring the economic viability of the glycerol electrooxidation process. The alternatives discussed here include Pd-based, Au-based, Ni-based, and Ag-based catalysts, as well as the combination of two or three of these metals. Also discussed here are the prospective materials that are yet to be explored for glycerol oxidation but are reported to be bifunctional (being capable of both anodic and cathodic reaction). These include heteroatom-doped metal-free electrocatalysts, which are carbon materials doped with one or two heteroatoms (N, B, S, P, F, I, Br, Cl), and heteroatom-doped nonprecious transition metals. Rational design of these materials can produce electrocatalysts with activity comparable to that of Pt/C catalysts. The takeaway from this review is that it provides an insight into further study and engineering applications on the efficient and cost-effective conversion of glycerol to value-added chemicals.

Controllable synthesis of Ir(Rh)–Sn/SiO2 bimetallic catalysts via surface organometallic chemistry for the production of ethanol from hydrogenolysis of ethyl acetate

A series of highly active Ir–Sn/SiO₂ and Rh–Sn/SiO₂ catalysts for ethyl acetate hydrogenolysis to ethanol were prepared from the grafting synthesis based on the surface organometallic chemistry concept.

Ultrafine PtCuRh nanowire catalysts with alleviated poisoning effect for efficient ethanol oxidation

As a green power source, direct ethanol fuel cells (DEFCs) have broad application prospects. However, most catalysts of DEFCs still exhibit defects, such as the difficulty of C-C bond cleavage, serious CO poisoning and limited catalytic activity. Here, we report ultrafine PtCuRh nanowires (NWs) with outstanding anti-CO-poisoning properties and enhanced activity. The average diameter of the ultrafine PtCuRh NWs is about 1.49 nm, effectively improving the atomic utilization efficiency (UE) of platinum. Owing to the combination of an ultrafine nanostructure, good electronic interaction and the high UE of Pt atoms, the optimized ultrafine PtCuRh NWs/C display superior electrocatalytic activity and stability compared with commercial Pt/C for the ethanol oxidation reaction (EOR). More importantly, further electrochemical results demonstrate that the incorporation of Rh is beneficial for enhancing the antipoisoning capability for some CO-like intermediates. Meanwhile, the synthetic method in this report is robust and universal, and can also be applied to the synthesis of ultrafine trimetallic PtCuPd and PtCuIr nanowires.

Electrochemical Characterization of Low-Temperature Direct Ethanol Fuel Cells using Direct and Alternate Current Methods

Here, we report for the first time the results of systematic characterization of a low-temperature polymer electrolyte membrane direct ethanol fuel cell using DC and AC electrochemical methods. Model catalysts (carbon supported Pt nanoparticles) painted on carbon paper are used as anode and cathode. Influence of physical parameters, such as cell temperature, current density, and ethanol concentration, and anode fuel flow rate on overall cell impedance is studied. Analysis of the obtained impedance spectra in connection with DC measurements allows us to comment on cell properties and to separate different contributions to the overall cell polarization. Our results suggest that the cell impedance is dominated by anode faradaic impedance, with a small or negligible contribution from cathode faradaic impedance. The anode impedance depends strongly on current density and cell temperature, but is not significantly influenced by ethanol concentration. Presence of anode mass-transfer impedance, even when ethanol was fed to the cell in high excess, is confirmed. Based on the results, we conclude that changes in ethanol electro-oxidation mechanism might manifest themselves on the impedance spectra in the low-frequency inductive loop. Nonetheless, further studies involving equivalent circuit modelling are needed to determine the exact influence of the cell parameters on the anode kinetics.

3D highly branched PtCoRh nanoassemblies: Glycine-assisted solvothermal synthesis and superior catalytic activity for alcohol oxidation

Advanced Pt-based ternary nanocatalysts display dramatically enhanced utilization efficiency of Pt alternative to mono- and bi-counterparts, owing to the synergistic effects of the tri-metals. Herein, multicomponent uniform 3D PtCoRh highly branched nanoassemblies (HBNAs) were prepared by glycine-assisted one-pot solvothermal method in oleylamine (OAm). The effects of the precursor types, reaction time and amount of glycine were critically investigated in this synthesis. The as-prepared PtCoRh HBNAs displayed outstanding electrocatalytic activity and improved stability towards ethanol oxidation reaction (EOR) and methanol oxidation reaction (MOR) in 1 M KOH electrolyte, whose mass/specific activities were 1.75 A mg^-1/4.03 mA cm^-2 and 0.98 A mg^-1/2.34 mA cm^-2, respectively, which were remarkably higher than commercial Pt/C (0.85 A mg^-1/4.03 mA cm^-2 and 0.47 A mg^-1/0.89 mA cm^-2). This study provides some novel guidelines to fabricate advanced multimetallic electrocatalysts for practical applications in direct alcohol fuel cells (DAFCs).

Nanocatalysts for Electrocatalytic Oxidation of Ethanol

The use of ethanol as a fuel in direct alcohol fuel cells depends not only on its ease of production from renewable sources, but also on overcoming the challenges of storage and transportation. In an ethanol-based fuel cell, highly active electrocatalysts are required to break the C-C bond in ethanol for its complete oxidation at lower overpotentials, with the aim of increasing the cell performance, ethanol conversion rates, and fuel efficiency. In recent decades, the development of wet-chemistry methods has stimulated research into catalyst design, reactivity tailoring, and mechanistic investigations, and thus, created great opportunities to achieve efficient oxidation of ethanol. In this Minireview, the nanomaterials tested as electrocatalysts for the ethanol oxidation reaction in acid or alkaline environments are summarized. The focus is mainly on nanomaterials synthesized by using wet-chemistry methods, with particular attention on the relationship between the chemical and physical characteristics of the catalysts, for example, catalyst composition, morphology, structure, degree of alloying, presence of oxides or supports, and their activity for ethanol electro-oxidation. As potential alternatives to noble metals, non-noble-metal catalysts for ethanol oxidation are also briefly reviewed. Insights into further enhancing the catalytic performance through the design of efficient electrocatalysts are also provided.

Pt-Based Catalysts for Electrochemical Oxidation of Ethanol

Despite its attractive features as a power source for direct alcohol fuel cells, utilization of ethanol is still hampered by both fundamental and technical challenges. The rationale behind the slow and incomplete ethanol oxidation reaction (EOR) with low selectivity towards CO₂ on most Pt-based catalysts is still far from being understood, and a number of practical problems need to be addressed before an efficient and low-cost catalyst is designed. Some recent achievements towards solving these problems are presented. Pt film electrodes and Pt monolayer (Pt_ML) electrodes on various single crystal substrates showed that EOR follows the partial oxidation pathway without C-C bond cleavage, with acetic acid and acetaldehyde as the final products. The role of the substrate lattice on the catalytic properties of Pt_ML was proven by the choice of appropriate M(111) structure (M = Pd, Ir, Rh, Ru and Au) showing enhanced kinetics when Pt_ML is under tensile strain on Au(111) electrode. Nanostructured electrocatalysts containing Pt-Rh solid solution on SnO₂ and Pt monolayer on non-noble metals are shown, optimized, and characterized by in situ methods. Electrochemical, in situ Fourier transform infrared (FTIR) and X-ray absorption spectroscopy (XAS) techniques highlighted the effect of Rh in facilitating C-C bond splitting in the ternary PtRh/SnO₂ catalyst. In situ FTIR proved quantitatively the enhancement in the total oxidation pathway to CO₂, and in situ XAS confirmed that Pt and Rh form a solid solution that remains in metallic form through a wide range of potentials due to the presence of SnO₂. Combination of these findings with density functional theory calculations revealed the EOR reaction pathway and the role of each constituent of the ternary PtRh/SnO₂ catalyst. The optimal Pt:Rh:Sn atomic ratio was found by the two in situ techniques. Attempts to replace Rh with cost-effective alternatives for commercially viable catalysts has shown that Ir can also split the C-C bond in ethanol, but the performance of optimized Pt-Rh-SnO₂ is still higher than that of the Pt-Ir-SnO₂ catalyst.

Synthesis and facile structure-adjusting of Pd–Pt nanocrystal electrocatalysts with improved activity for ethanol oxidation reaction

Illustration of the synthesis of the nanospheroid-, nanoflower- and nanoworm-Pd–Pt NCs and their electrocatalytic activity for ethanol oxidation.

Nanostructure Optimization of Platinum-Based Nanomaterials for Catalytic Applications

Platinum-based nanomaterials have attracted much interest for their promising potentials in fields of energy-related and environmental catalysis. Designing and controlling the surface/interface structure of platinum-based nanomaterials at the atomic scale and understanding the structure-property relationship have great significance for optimizing the performances in practical catalytic applications. In this review, the strategies to obtain platinum-based catalysts with fantastic activity and great stability by composition regulation, shape control, three-dimension structure construction, and anchoring onto supports, are presented in detail. Moreover, the structure-property relationship of platinum-based nanomaterials are also exhibited, and a brief outlook are given on the challenges and possible solutions in future development of platinum-based nanomaterials towards catalytic reactions.

Vertex-Type Engineering of Pt-Cu-Rh Heterogeneous Nanocages for Highly Efficient Ethanol Electrooxidation

Mastery over the architecture and elemental distribution of metal nanocrystals at the nanoscale can effectively tailor and improve their catalytic properties. Herein, the vertex-type-selective growth of metallic nanohorns on a central nanocrystal is constructed via a one-pot solvothermal synthesis, despite the fact that the site-selective epitaxy of the second phase proceeds on all the vertices of the seeds. The prepared vertex-type-selective Pt-Cu-Rh heterogeneous nanocages (HNCs) are composed of a Rh-decorated Pt-Cu rhombic dodecahedral nanocage and six Pt-Cu-Rh nanohorns protruding from the {100} rather than the {111} vertices of rhombic dodecahedron. Impressively, the Pt-Cu-Rh HNCs exhibit 8.1 times higher specific and 6.8 times higher mass activity toward the ethanol oxidation reaction under acidic conditions than commercial Pt/C catalysts. Besides, the peak potential for CO oxidation on Pt-Cu-Rh HNCs (370.4 mV vs SCE) is 182.0 mV more negative than that on Pt/C, indicating the dramatically enhanced CO tolerance. The excellent electrocatalytic property is attributed to the synergistic effect between Pt, Cu, and Rh components, high specific surface area of nanocages and nanohorns, as well as abundant concave/convex sites and various high-index facets around the surface.

Bimetallic Platinum-Rhodium Alloy Nanodendrites as Highly Active Electrocatalyst for the Ethanol Oxidation Reaction

Rationally designing and manipulating composition and morphology of precious metal-based bimetallic nanostructures can markedly enhance their electrocatalytic performance, including selectivity, activity, and durability. We herein report the synthesis of bimetallic PtRh alloy nanodendrites (ANDs) with tunable composition by a facile complex-reduction synthetic method under hydrothermal conditions. The structural/morphologic features, formation mechanism, and electrocatalytic performance of PtRh ANDs are investigated thoroughly by various physical characterization and electrochemical methods. The preformed Rh crystal nuclei effectively catalyze the reduction of Pt²⁺ precursor, resulting in PtRh alloy generation due to the catalytic growth and atoms interdiffusion process. The Pt atoms deposition distinctly interferes in Rh atoms deposition on Rh crystal nuclei, resulting in dendritic morphology of PtRh ANDs. For the ethanol oxidation reaction (EOR), PtRh ANDs display the chemical composition and solution pH co-dependent electrocatalytic activity. Because of the alloy effect and particular morphologic feature, Pt₁Rh₁ ANDs with optimized composition exhibit better reactivity and stability for the EOR than commercial Pt nanocrystals electrocatalyst.

PdAg Bimetallic Nanoalloy-Decorated Graphene: A Nanohybrid with Unprecedented Electrocatalytic, Catalytic, and Sensing Activities

Recent reports about the promising and tunable electrocatalytic activity and stability of nanoalloys have stimulated an intense research activity toward the design and synthesis of homogeneously alloyed novel bimetallic nanoelectrocatalysts. We herein present a simple one-pot facile wet-chemical approach for the deposition of high-quality bimetallic palladium-silver (PdAg) homogeneous nanoalloy crystals on reduced graphene (Gr) oxide sheets. Morphological, structural, and chemical characterizations of the so-crafted nanohybrids establish a homogeneous distribution of 1:1 PdAg nanoalloy crystals supported over reduced graphene oxide (PdAg-Gr). The PdAg-Gr nanohybrids exhibit outstanding electrocatalytic, catalytic, and electroanalytical performances. The PdAg-Gr samples were found to exhibit exceptional durability when subjected to repeated potential cycles or long-term electrolysis. In the CVs recorded for fuel cell reactions, viz. methanol oxidation reaction and oxygen reduction reaction, and for detoxification of environmental pollutants, viz. electroreduction of methyl iodide and chloroacetonitrile over PdAg-Gr with potential sweep rate of 25 mVs^-1, the peak potentials were observed to be just -0.221, -0.297, (vs Ag/AgCl, 3 M KCl) -1.508, and -1.189 V (vs Fc⁺/Fc), respectively. The potential of PdAg-Gr nanohybrid for simultaneous and sensitive electrochemical sensing and estimation of hydroxybenzene isomers with very low detection limits (0.05 μM for hydroquinone, 0.06 μM for catechol, 6.7 nM for 4-aminophenol, and 13.7 nM for 2-aminophenol) is demonstrated. Additionally, PdAg-Gr was observed to offer excellent solution-phase catalytic performance in bringing about the reduction of notorious environmental pollutant 4-nitrophenol to pharmaceutically important 4-aminophenol with an apparent rate constant ( k_app) of 3.106 × 10^-2 s^-1 and a normalized rate constant ( k_nor) of 6.21 × 10² s^-1 g^-1. The presented synthetic scheme besides being high yielding, low cost, and easy to carry out results in the production of PdAg-Gr nanohybrids with stability and activity significantly better than most of the nanomaterials purposefully designed and testified so far by various groups.

Pt-Richcore/Sn-Richsubsurface/Ptskin Nanocubes As Highly Active and Stable Electrocatalysts for the Ethanol Oxidation Reaction

Direct ethanol fuel cells are one of the most promising electrochemical energy conversion devices for portable, mobile and stationary power applications. However, more efficient and stable and less expensive electrocatalysts are still required. Interestingly, the electrochemical performance of the electrocatalysts toward the ethanol oxidation reaction can be remarkably enhanced by exploiting the benefits of structural and compositional sensitivity and control. Here, we describe the synthesis, characterization, and electrochemical behavior of cubic Pt-Sn nanoparticles. The electrochemical activity of the cubic Pt-Sn nanoparticles was found to be about three times higher than that obtained with unshaped Pt-Sn nanoparticles and six times higher than that of Pt nanocubes. In addition, stability tests indicated the electrocatalyst preserves its morphology and remains well-dispersed on the carbon support after 5000 potential cycles, while a cubic (pure) Pt catalyst exhibited severe agglomeration of the nanoparticles after a similar stability testing protocol. A detailed analysis of the elemental distribution in the nanoparticles by STEM-EELS indicated that Sn dissolves from the outer part of the shell after potential cycling, forming a ∼0.5 nm Pt skin. This particular atomic composition profile having a Pt-rich core, a Sn-rich subsurface layer, and a Pt-skin surface structure is responsible for the high activity and stability.

Porous Pt–NiOx nanostructures with ultrasmall building blocks and enhanced electrocatalytic activity for the ethanol oxidation reaction

A porous Pt–NiO_x nanomaterial was constructed by a simple strategy to achieve excellent ethanol oxidation catalyst performance.

Rational one-step synthesis of porous PtPdRu nanodendrites for ethanol oxidation reaction with a superior tolerance for CO-poisoning

Precise fabrication of porous ternary Pt-based nanodendrites is very important for electrochemical energy conversion owing to high surface area and great molecular accessibility of these nanodendrites. Herein, PtPdRu porous nanodendrites (PNDs) were prepared via a facile one-step ultrasonic irradiation approach at room temperature. Intriguingly, the ultrasonic irradiation drove the formation of PtPdRu PNDs with spatially interconnected porous structures, whereas magnetic stirring produced PtPdRu nanoflowers (NFs) with less porosity. The formation mechanism was ascribed to the acoustic cavitation effect and fast-reduction kinetics under sonication. The as-made PtPdRu PNDs displayed a superior catalytic performance towards ethanol oxidation reaction with a high tolerance for CO-poisoning as compared to PtPdRu NFs, PtPd NDs, and commercial Pt/C catalyst.

Finite Size Effects in Submonolayer Catalysts Investigated by CO Electrosorption on PtsML/Pd(100)

A combination of scanning tunneling microscopy, subtractively normalized interfacial Fourier transform infrared spectroscopy (SNIFTIRS), and density functional theory (DFT) is used to quantify the local strain in 2D Pt clusters on the 100 facet of Pd and its effect on CO chemisorption. Good agreement between SNIFTIRS experiments and DFT simulations provide strong evidence that, in the absence of coherent strain between Pt and Pd, finite size effects introduce local compressive strain, which alters the chemisorption properties of the surface. Though this effect has been widely neglected in prior studies, our results suggest that accurate control over cluster sizes in submonolayer catalyst systems can be an effective approach to fine-tune their catalytic properties.

Ethanol Oxidation Reaction on Tandem Pt/Rh/SnOx Catalyst

To elucidate the atomic arrangement of a Pt-Rh-Sn ternary catalyst with a high catalytic activity for ethanol oxidation reaction (EOR) and high CO2 selectivity, we prepared a tandem Pt/Rh/SnOx, in which a Rh adlayer was deposited on a Pt substrate (Rh coverage: 0.28), followed by depositing several layers of SnOx only on the Rh surface (Sn coverage: 0.07). For reference, Sn was randomly deposited on the Rh-modified Pt (Pt/Rh) electrode whose Rh and Sn coverages were 0.22 and 0.36 (random Pt/Rh/SnOx). X-ray photoelectron spectroscopy demonstrated that Pt and Rh were metallic, and Sn was largely oxidized. Both Pt/Rh/SnOx electrodes were less positive in onset potential of EOR current density and higher in EOR current density than Pt and Rh/Pt electrodes. In situ infrared reflection-absorption spectroscopy demonstrated that the tandem Pt/Rh/SnOx electrode did not produce acetic acid, but produced CO2 in contrast to the random Pt/Rh/SnOx, suggesting that a tandem arrangement of Pt, Rh and SnOx, in which the Pt and SnOx sites were separated by the Rh sites, was effective for selective CO2 production. In the electrostatic electrolysis at 0.5 V vs. RHE, the tandem Pt/Rh/SnOx electrode exhibited higher EOR current density than the Pt and Pt/Rh electrodes after 1.5 h.

Trimetallic PtSnRh Wavy Nanowires as Efficient Nanoelectrocatalysts for Alcohol Electrooxidation

The design and creation of efficient catalysts for alcohol oxidation reaction has attracted great research attention because alcohols are promising fuels for direct fuel cell reactions because of their high energy density, easy storage, and transportation. We herein report an efficient strategy that allows the preparation of ternary PtSnM (M=Co, Ni, and Rh) wavy nanowires (WNWs) with ultrathin diameter of only around 2 nm and tunable compositions in high yield. Detailed catalytic studies show that all the ternary WNWs exhibit high performance for ethanol oxidation reaction (EOR) and methanol oxidation reaction (MOR), and their performance shows interesting composition-dependent electrocatalytic activity with PtSnRh WNWs having the best activity for both EOR and MOR. The PtSnRh WNWs are also more stable than commercial Pt/C catalyst, as revealed by long-time chronoamperometric (CA) measurements. The present work highlights the use of multimetallic WNWs as highly active and durable nanocatalysts in enhancing alcohol electrooxidation, which will open a new way in tuning 1D multimetallic nanostructures for boosting other fuel cell reactions, various heterogeneous reactions, and beyond.

Facile One-Step Synthesis of Three-Dimensional Pd-Ag Bimetallic Alloy Networks and Their Electrocatalytic Activity toward Ethanol Oxidation

The three-dimensional palladium networks and palladium-silver bimetallic alloy networks were synthesized at room temperature on a large scale using a rapid and simple strategy. The results revealed that the morphology of the networks is not affected by the composition. We demonstrated that the as-prepared unsupported networks exhibited excellent electrochemical activity and stability toward ethanol oxidation reaction in alkaline media due to the formation of palladium-silver alloys as well as the porous nanostructures. The results indicate that the well-defined three-dimensional palladium-silver bimetallic alloy networks are promising catalysts for fuel cells.