Impact of organosulfur content on diesel fuel stability and implications for carbon steel corrosion

Microbiologically Influenced Corrosion of Copper and Its Alloys in Anaerobic Aqueous Environments: A Review

Regardless of the long record of research works based on microbiologically influenced corrosion (MIC), its principle and mechanism, which lead to accelerated corrosion, is yet to be fully understood. MIC is observed on different metallic substrates and can be caused by a wide variety of microorganisms with sulfate-reducing bacteria (SRB) being considered the most prominent and economically destructive one. Copper and its alloys, despite being used as an antimicrobial agent, are recorded to be susceptible to microbial corrosion. This review offers a research overview on MIC of copper and its alloys in anaerobic aqueous environments. Proposed MIC mechanisms, recent work and developments as well as MIC inhibition techniques are presented focusing on potable water systems and marine environment. In the future research perspectives section, the importance and possible contribution of knowledge about intrinsic properties of substrate material are discussed with the intent to bridge the knowledge gap between microbiology and materials science related to MIC.

In situ Linkage of Fungal and Bacterial Proliferation to Microbiologically Influenced Corrosion in B20 Biodiesel Storage Tanks

Renewable fuels hold great promise for the future yet their susceptibility to biodegradation and subsequent corrosion represents a challenge that needs to be directly assessed. Biodiesel is a renewable fuel that is widely used as a substitute or extender for petroleum diesel and is composed of a mixture of fatty acid methyl esters derived from plant or animal fats. Biodiesel can be blended up to 20% v/v with ultra-low sulfur diesel (i.e., B20) and used interchangeably with diesel engines and infrastructure. The addition of biodiesel, however, has been linked to increased susceptibility to biodegradation. Microorganisms proliferating via degradation of biodiesel blends have been linked to microbiologically influenced corrosion in the laboratory, but not measured directly in storage tanks (i.e., in situ). To measure in situ microbial proliferation, fuel degradation and microbially influenced corrosion, we conducted a yearlong study of B20 storage tanks in operation at two locations, identified the microorganisms associated with fuel fouling, and measured in situ corrosion. The bacterial populations were more diverse than the fungal populations, and largely unique to each location. The bacterial populations included members of the Acetobacteraceae, Clostridiaceae, and Proteobacteria. The abundant Eukaryotes at both locations consisted of the same taxa, including a filamentous fungus within the family Trichocomaceae, not yet widely recognized as a contaminant of petroleum fuels, and the Saccharomycetaceae family of yeasts. Increases in the absolute and relative abundances of the Trichocomaceae were correlated with significant, visible fouling and pitting corrosion. This study identified the relationship between fouling of B20 with increased rates of corrosion and the microorganisms responsible, largely at the bottom of the sampled storage tanks. To our knowledge this is the first in situ study of this scale incorporating community and corrosion measurements in an active biodiesel storage environment.

Dual-Purpose 3D Pillared Metal-Organic Framework with Excellent Properties for Catalysis of Oxidative Desulfurization and Energy Storage in Asymmetric Supercapacitor

This study proposes an approach for improving catalysis of oxidative desulfurization (ODS) of diesel fuel under mild reaction conditions and enhancing supercapacitor (SC) properties for storage of a high amount of charge. Our approach takes advantage of a novel dual-purpose cobalt(II)-based metal-organic framework (MOF), [Co(2-ATA)₂(4-bpdb)₄] _n (2-ATA: 2-aminoterephthalic acid and 4-bpdb: N, N-bis-pyridin-4-ylmethylene-hydrazine as the pillar spacer), which is called NH₂-TMU-53. Due to the stability of the used compound, we decided to evaluate the capability of this compound as a novel electrode material for storing energy in supercapacitors, and also to investigate its catalytic capabilities. It is demonstrated that the addition of H₂O₂ as an oxidant enhances the efficiency of sulfur removal, which indicates that NH₂-TMU-53 can efficiently catalyze the ODS reaction. According to the kinetics results, the catalyzed process follows pseudo-first-order kinetics and exhibits 15.57 kJ mol^-1 activation energy. Moreover, with respect to the radical scavenging evaluations, the process is governed by direct catalytic oxidation rather than indirect oxidative attack of radicals. Furthermore, NH₂-TMU-53 was applied as an electrode material for energy storage in SCs. This material is used in the three-electrode system and shows a specific capacitance of 325 F g^-1 at 5 A g^-1 current density. The asymmetric supercapacitor of NH₂-TMU-53//activated carbon evaluates the further electrochemical activity in real applications, delivers the high power density (2.31 kW kg^-1), high energy density (50.30 Wh kg^-1), and long cycle life after 6000 cycles (90.7%). Also, the asymmetric supercapacitor practical application was demonstrated by a glowing red light-emitting diode and driving a mini-rotating motor. These results demonstrate that the fabricated device presents a good capacity for energy storage without pyrolyzing the MOF structures. These findings can guide the development of high-performance SCs toward a new direction to improve their practical applications and motivate application of MOFs without pyrolysis or calcination.

Anaerobic biodegradation of biofuels and their impact on the corrosion of a Cu-Ni alloy in marine environments

Fuel biodegradation linked to sulfate reduction can lead to corrosion of the metallic infrastructure in a variety of marine environments. However, the biological stability of emerging biofuels and their potential impact on copper-nickel alloys commonly used in marine systems has not been well documented. Two potential naval biofuels (Camelina-JP5 and Fisher-Tropsch-F76) and their petroleum-derived counterparts (JP5 and F76) were critically assessed in seawater/sediment incubations containing a metal coupon (70/30 Cu-Ni alloy). Relative to a fuel-unamended control (1.2 ± 0.4 μM/d), Camelina-JP5 (86.4 ± 1.6 μM/d) and JP5 (77.6 ± 8.3 μM/d) stimulated much higher rates of sulfate reduction than either FT-F76 (11.4 ± 2.7 μM/d) or F76 (38.4 ± 3.7 μM/d). The general corrosion rate (r² = 0.91) and pitting corrosion (r² = 0.92) correlated with sulfate loss in these incubations. Despite differences in microbial community structure on the metal or in the aqueous or sediment phases, sulfate reducing bacteria affiliated with Desulfarculaceae and Desulfobacteraceae became predominant upon fuel amendment. The identification of alkylsuccinates and alkylbenzylsuccinates attested to anaerobic metabolism of fuel hydrocarbons. Sequences related to Desulfobulbaceae were highly enriched (34.2-64.8%) on the Cu-Ni metal surface, regardless of whether the incubation received a fuel amendment. These results demonstrate that the anaerobic metabolism of biofuel linked to sulfate reduction can exacerbate the corrosion of Cu-Ni alloys. Given the relative lability of Camelina-JP5, particular precaution should be taken when incorporating this hydroprocessed biofuel into marine environments serviced by a Cu-Ni metallic infrastructure.

Impact of Photooxidation and Biodegradation on the Fate of Oil Spilled During the Deepwater Horizon Incident: Advanced Stages of Weathering

While the biogeochemical forces influencing the weathering of spilled oil have been investigated for decades, the environmental fate and effects of "oxyhydrocarbons" in sand patties deposited on beaches are not well-known. We collected sand patties deposited in the swash zone on Gulf of Mexico beaches following the Deepwater Horizon oil spill. When sand patties were exposed to simulated sunlight, a larger concentration of dissolved organic carbon was leached into seawater than the corresponding dark controls. This result was consistent with the general ease of movement of seawater through the sand patties as shown with a ³⁵SO₄^2- radiotracer. Ultrahigh-resolution mass spectrometry, as well as optical measurements revealed that the chemical composition of dissolved organic matter (DOM) leached from the sand patties under dark and irradiated conditions were substantially different, but neither had a significant inhibitory influence on the endogenous rate of aerobic or anaerobic microbial respiratory activity. Rather, the dissolved organic photooxidation products stimulated significantly more microbial O₂ consumption (113 ± 4 μM) than either the dark (78 ± 2 μM) controls or the endogenous (38 μM ± 4) forms of DOM. The changes in the DOM quality and quantity were consistent with biodegradation as an explanation for the differences. These results confirm that sand patties undergo a gradual dissolution of DOM in both the dark and in the light, but photooxidation accelerates the production of water-soluble polar organic compounds that are relatively more amenable to aerobic biodegradation. As such, these processes represent previously unrecognized advanced weathering stages that are important in the ultimate transformation of spilled crude oil.

Metabolic Capability of a Predominant Halanaerobium sp. in Hydraulically Fractured Gas Wells and Its Implication in Pipeline Corrosion

Microbial activity associated with produced water from hydraulic fracturing operations can lead to gas souring and corrosion of carbon-steel equipment. We examined the microbial ecology of produced water and the prospective role of the prevalent microorganisms in corrosion in a gas production field in the Barnett Shale. The microbial community was mainly composed of halophilic, sulfidogenic bacteria within the order Halanaerobiales, which reflected the geochemical conditions of highly saline water containing sulfur species (S2O3 (2-), SO4 (2-), and HS(-)). A predominant, halophilic bacterium (strain DL-01) was subsequently isolated and identified as belonging to the genus Halanaerobium. The isolate could degrade guar gum, a polysaccharide polymer used in fracture fluids, to produce acetate and sulfide in a 10% NaCl medium at 37°C when thiosulfate was available. To mitigate potential deleterious effects of sulfide and acetate, a quaternary ammonium compound was found to be an efficient biocide in inhibiting the growth and metabolic activity of strain DL-01 relative to glutaraldehyde and tetrakis (hydroxymethyl) phosphonium sulfate. Collectively, our findings suggest that predominant halophiles associated with unconventional shale gas extraction could proliferate and produce sulfide and acetate from the metabolism of polysaccharides used in hydraulic fracturing fluids. These metabolic products might be returned to the surface and transported in pipelines to cause pitting corrosion in downstream infrastructure.

Anaerobic Biodegradation of Alternative Fuels and Associated Biocorrosion of Carbon Steel in Marine Environments

Fuels that biodegrade too easily can exacerbate through-wall pitting corrosion of pipelines and tanks and result in unintentional environmental releases. We tested the biological stability of two emerging naval biofuels (camelina-JP5 and Fischer-Tropsch-F76) and their potential to exacerbate carbon steel corrosion in seawater incubations with and without a hydrocarbon-degrading sulfate-reducing bacterium. The inclusion of sediment or the positive control bacterium in the incubations stimulated a similar pattern of sulfate reduction with different inocula. However, the highest rates of sulfate reduction were found in incubations amended with camelina-JP5 [(57.2 ± 2.2)-(80.8 ± 8.1) μM/day] or its blend with petroleum-JP5 (76.7 ± 2.4 μM/day). The detection of a suite of metabolites only in the fuel-amended incubations confirmed that alkylated benzene hydrocarbons were metabolized via known anaerobic mechanisms. Most importantly, general (r(2) = 0.73) and pitting (r(2) = 0.69) corrosion were positively correlated with sulfate loss in the incubations. Thus, the anaerobic biodegradation of labile fuel components coupled with sulfate respiration greatly contributed to the biocorrosion of carbon steel. While all fuels were susceptible to anaerobic metabolism, special attention should be given to camelina-JP5 biofuel due to its relatively rapid biodegradation. We recommend that this biofuel be used with caution and that whenever possible extended storage periods should be avoided.

Municipal Solid Waste Landfills Harbor Distinct Microbiomes

Landfills are the final repository for most of the discarded material from human society and its “built environments.” Microorganisms subsequently degrade this discarded material in the landfill, releasing gases (largely CH₄ and CO₂) and a complex mixture of soluble chemical compounds in leachate. Characterization of “landfill microbiomes” and their comparison across several landfills should allow the identification of environmental or operational properties that influence the composition of these microbiomes and potentially their biodegradation capabilities. To this end, the composition of landfill microbiomes was characterized as part of an ongoing USGS national survey studying the chemical composition of leachates from 19 non-hazardous landfills across 16 states in the continental U.S. The landfills varied in parameters such as size, waste composition, management strategy, geography, and climate zone. The diversity and composition of bacterial and archaeal populations in leachate samples were characterized by 16S rRNA gene sequence analysis, and compared against a variety of physical and chemical parameters in an attempt to identify their impact on selection. Members of the Epsilonproteobacteria, Gammaproteobacteria, Clostridia, and candidate division OP3 were the most abundant. The distribution of the observed phylogenetic diversity could best be explained by a combination of variables and was correlated most strongly with the concentrations of chloride and barium, rate of evapotranspiration, age of waste, and the number of detected household chemicals. This study illustrates how leachate microbiomes are distinct from those of other natural or built environments, and sheds light on the major selective forces responsible for this microbial diversity.

Anaerobic hydrocarbon and fatty acid metabolism by syntrophic bacteria and their impact on carbon steel corrosion

The microbial metabolism of hydrocarbons is increasingly associated with the corrosion of carbon steel in sulfate-rich marine waters. However, how such transformations influence metal biocorrosion in the absence of an electron acceptor is not fully recognized. We grew a marine alkane-utilizing, sulfate-reducing bacterium, Desulfoglaeba alkanexedens, with either sulfate or Methanospirillum hungatei as electron acceptors, and tested the ability of the cultures to catalyze metal corrosion. Axenically, D. alkanexedens had a higher instantaneous corrosion rate and produced more pits in carbon steel coupons than when the same organism was grown in syntrophic co-culture with the methanogen. Since anaerobic hydrocarbon biodegradation pathways converge on fatty acid intermediates, the corrosive ability of a known fatty acid-oxidizing syntrophic bacterium, Syntrophus aciditrophicus was compared when grown in pure culture or in co-culture with a H₂-utilizing sulfate-reducing bacterium (Desulfovibrio sp., strain G11) or a methanogen (M. hungatei). The instantaneous corrosion rates in the cultures were not substantially different, but the syntrophic, sulfate-reducing co-culture produced more pits in coupons than other combinations of microorganisms. Lactate-grown cultures of strain G11 had higher instantaneous corrosion rates and coupon pitting compared to the same organism cultured with hydrogen as an electron donor. Thus, if sulfate is available as an electron acceptor, the same microbial assemblages produce sulfide and low molecular weight organic acids that exacerbated biocorrosion. Despite these trends, a surprisingly high degree of variation was encountered with the corrosion assessments. Differences in biomass, initial substrate concentration, rates of microbial activity or the degree of end product formation did not account for the variations. We are forced to ascribe such differences to the metallurgical properties of the coupons.