Induction and coverage times for crude oil droplets spreading on air bubbles

Flotation mechanism and performance of air/condensate bubbles for removing oil droplets in the presence of acetic acid

Flotation technology is widely utilized to remove emulsified oil droplets from Produced water. Organic acid adsorption on the oil droplet surface affects bubble attachment, reducing oil removal efficiency. This investigation exploited the principle of similar dissolution to synthesize condensate bubbles (CB). The surface properties of oil droplets and CB and air bubbles (AB) were appraised using FTIR, zeta potential, interfacial tension, and contact angle measurements. The research also investigated the effects of acetic acids (AA) on the adhesion of oil droplets to AB and CB along with the underlying mechanism via the Extended Derjaguin-Landau-Verwey-Overbeek (EDLVO) interaction theory and the Stefan-Reynolds model of liquid film thinning, integrated with adhesion times. Flotation efficiency and kinetic dissimilarities between AB and CB were also examined. The results indicated that CB exhibits superior lipophilic hydrophobicity compared to AB, reduced induction and spreading times upon oil droplet attachment, and maximized oil removal efficiency. Furthermore, CB could mitigate the impact of AA on adhesion. The interaction barriers between CB and oil droplets were minimal, and the thinning rate of the hydration film was quicker than in AB. The conventional first-order model proved effective in fitting the AB flotation, whereas a delay constant was applied to the model of the CB flotation rate.

Separation of emulsified crude oil from produced water by gas flotation: A review

The development and production of oil and gas fields would eventually result in a considerable amount of oily generated water, posing serious risks to humans and the environment. Nowadays, the oil concentration in the drainage stream of the produced water is strictly regulated, and many countries have established strict emission standards. As an indispensable oily wastewater treatment technology, flotation technology has attracted much attention because of its maturity, economy, practicality, and relative efficiency. Firstly, this paper summarizes and compares flotation techniques, such as dissolved gas flotation, induced gas flotation, electroflotation, and compact flotation units widely used in produced water treatment offshore in recent years. Considering the complexity of the mechanism of oil removal by air flotation, the mechanism of the oil droplet-bubble interaction is further discussed. The effects of flocculant, PH, and salinity on the oil droplet-bubble interaction in the flotation process were summarized from the perspective of the microscopic colloidal interface, which has a specific guiding role in improving the oil removal efficiency in the gas flotation process. Finally, the research status of produced water treatment by air flotation is summarized, and the feasible research direction is put forward.

Flotation separation of hazardous polyvinyl chloride towards source control of microplastics based on selective hydrophilization of plasticizer-doping surfaces

As the single largest chlorine source of plastics, hazardous polyvinyl chloride (PVC) has become an increasing environmental concern with the rapid microplastics accumulation. An advanced separation method is advocated to purify waste PVC plastics, optimize physical recycling, and protect aquatic and terrestrial environment safety. In this study, we proposed a novel scheme for the flotation separation of PVC plastics with diverse plasticizer contents (PVCs) via regulating hydrophilicity based on a selective ferric deposition. Rigid PVCs were prone to loading ferric ions and generating hydrophilic shells than flexible PVCs. Plasticizers can diffuse freely through the interior and surface of PVC plastics. Abundant plasticizers thereby overlaid the surface of flexible PVC and shielded PVC matrix from ferric ions. By regulating the ferric concentration, the wettability of PVCs was adjusted to separate rigid and flexible PVCs by froth flotation. Waste PVCs could also be separated from each other through the compound process of ferric deposition and flotation, further confirming its feasibility and stability. Thus far, this study supplies distinctive insights into the wettability regulation of plasticizer-doping PVC surfaces, contributes a pioneering hydrophilization method to PVCs separation and recycling, and mitigates hazardous PVC microplastics by source control.

Colloid chemistry and experimental techniques for understanding fundamental behaviour of produced water in oil and gas production

Due to increasing volumes of produced water and environmental concerns related to its discharge, water treatment has become a major challenge during the production of crude oil and natural gas. With continuously stricter regulations for discharging produced water to sea, the operators are obliged to look for ways to improve the treatment processes or re-use the water in a beneficial way, for example as a pressure support during oil recovery (produced water re-injection). To improve the knowledge of the underlying phenomena governing separation processes, detailed information of the composition and interfacial properties of produced water is undoubtedly useful and could provide valuable input for better understanding and improving separation models. This review article summarizes knowledge gained about produced water composition and the most common treatment technologies, which are later used to describe the fundamental phenomena occurring during separation. These colloidal interactions, such as coalescence of oil droplets, bubble-droplet attachment or partitioning of components between oil and water, are of crucial importance for the performance of various technologies and are sometimes overlooked in physical considerations of produced water treatment. The last part of the review deals with the experimental methodologies that are available to study these phenomena, provide data for models and support development of more efficient separation processes.

Bubble Meets Droplet: Particle-Assisted Reconfiguration of Wetting Morphologies in Colloidal Multiphase Systems

Wetting phenomena are ubiquitous in nature and play key functions in various industrial processes and products. When a gas bubble encounters an oil droplet in an aqueous medium, it can experience either partial wetting or complete engulfment by the oil. Each of these morphologies can have practical benefits, and controlling the morphology is desirable for applications ranging from particle synthesis to oil recovery and gas flotation. It is known that the wetting of two fluids within a fluid medium depends on the balance of interfacial tensions and can thus be modified with surfactant additives. It is reported that colloidal particles, too, can be used to promote both wetting and dewetting in multifluid systems. This study demonstrates the surfactant-free tuning and dynamic reconfiguration of bubble-droplet morphologies with the help of cellulosic particles. It further shows that the effect can be attributed to particle adsorption at the fluid interfaces, which can be probed by interfacial tensiometry, making particle-induced transitions in the wetting morphology predictable. Finally, particle adsorption at different rates to air-water and oil-water interfaces can even lead to slow, reentrant wetting behavior not familiar from particle-free systems.