Enhanced arsenic removal by hydrothermally treated nanocrystalline Mg/Al layered double hydroxide with nitrate intercalation

Morphologically controlled synthesis of MgFe-LDH using MgO and succinic acid for enhanced arsenic adsorption: Kinetics, equilibrium, and mechanism studies

In this study, we investigated improving the performance of a layered double hydroxide (LDH) for the adsorption of As(III) and As(V) by controlling the morphology of LDH crystals. The LDH was synthesized via a simple coprecipitation method using barely soluble MgO as a precursor and succinic acid (SA) as a morphological control agent. Doping the LDH crystals with carboxylate ions (RCOO-) derived from SA caused the crystals to develop in a radial direction. This changed the pore characteristics and increased the density of active surface sites. Subsequently, SA/MgFe-LDH showed excellent affinity for As(III) and As(V) with maximum sorption densities of 2.42 and 1.60 mmol/g, respectively. By comparison, the pristine MgFe-LDH had sorption capacities of 1.56 and 1.31 mmol/g for As(III) and As(V), respectively. The LDH was effective over a wide pH range for As(III) adsorption (pH 3-8.5) and As(V) adsorption (pH 3-6.5). Using a combination of spectroscopy and sorption modeling calculations, the main sorption mechanism of As(III) and As(V) on SA/MgFe-LDH was identified as inner-sphere complexation via ligand exchange with hydroxyl group (-OH) and RCOO-. Specifically, bidentate As-Fe complexes were proposed for both As(III) and As(V) uptake, with the magnitude of formation varying with the initial As concentration. Importantly, the As-laden adsorbent had satisfactory stability in simulated real landfill leachate. These findings demonstrate that SA/MgFe-LDH exhibits considerable potential for remediation of As-contaminated water.

Sorption-oxidation mechanism for the removal of arsenic (III) using Cu-doped ZnO in an alkaline medium

1-D oxides Zn1-xCuxO and spherical composites Zn1-xCuxO/CuO were obtained by thermolysis of formate-glycolate complexes Zn1-xCux (HCOO)(OCH2CH2O)1/2 (0 ≤ x ≤ 0.15). The structural and property characteristics showed that Cu was introduced into the Zn site of the ZnO lattice to form the Zn0.95Cu0.05O solid solution. The concentration of copper in the precursors regulates the topological and structural features of the formation of Zn1-xCuxO oxides, which determine their sorption and photocatalytic properties. The materials were tested in As3+ photooxidation reaction under UV and visible radiation. It has been established that Cu+ is an effective dopant in the composition of 1-D oxide Zn1-xCuxO (0 ≤ x < 0.1). The presence of Cu2+ in the shell of Zn1-xCuxO/CuO composite reduces the photoactivity of the material. The maximum efficiency of arsenic extraction (up to 80% for Zn0.95Cu0.05O) was achieved from dilute arsenic-containing solutions (3.8 mg/L As) and an adsorbent concentration of 0.8 g/L for 24 h. In saturated solutions (380 mg/L As) this value is reduced by a factor of 100. According to XPS data, the primary process is As3+ sorption on the catalyst surface followed by its oxidation to As5+. Using the EPR method it was found that singly charged oxygen vacanciesV O + $$ {V}_O^{+} $$ associated with Cu in Zn1-xCuxO are directly involved in the photostimulated oxidation of As3+. PRACTITIONER POINTS: Two types of Zn1-x Cux O photocatalysts were obtained by thermolysis of the Zn1-x Сux (HCOO)(OCH2 CH2 O)1/2 complex (0 ≤ x ≤ 0.15) in air. Sorption of arsenic from dilute solutions reaches 80% on 1-D oxide Zn0.95 Cu0.05 O. Sorption of As3+ on the catalyst surface is at primary process followed by its oxidation to As5+ . Removal of As3+ from alkaline solutions occurs due to successful combination of sorption and photocatalytic properties of the 1-D oxides Zn1-x Cux O.

Layered Double Hydroxide Materials: A Review on Their Preparation, Characterization, and Applications

Layered double hydroxides (LDHs), a type of synthetic clay with assorted potential applications, are deliberated upon in view of their specific properties, such as adsorbent-specific behavior, biocompatibility, fire-retardant capacity, and catalytic and anion exchange properties, among others. LDHs are materials with two-dimensional morphology, high porosity, and exceptionally tunable and exchangeable anionic particles with sensible interlayer spaces. The remarkable feature of LDHs is their flexibility in maintaining the interlayer spaces endowing them with the capacity to accommodate a variety of ionic species, suitable for many applications. Herein, some synthetic methodologies, general characterizations, and applications of LDHs are summarized, encompassing their broader appliances as a remarkable material to serve society and address several problems viz. removal of pollutants and fabrication of sensors and materials with multifaceted useful applications in the medical, electrochemical, catalytic, and agricultural fields, among others.

Anchored growth of highly dispersed LDHs nanosheets on expanded graphite for fluoride adsorption properties and mechanism

In this study, a new composite with layered double hydroxides (LDHs) anchored grown on expanded graphite (EG) interlayers was prepared by vacuum-assisted intercalation and hydrothermal method. Both sides of EG were completely covered by highly dispersed LDHs nanosheets and formed a sandwich-like structure. The unique structure made expanded graphite/layered double hydroxides (EG/LDHs) composites which had excellent F^- adsorption performance. The adsorption performance of F^- on EG/LDHs was evaluated, and the results indicated that the adsorption process was consistent with the pseudo-second-order kinetic model and the Langmuir model. Pseudo-second-order kinetic model indicated that the adsorption sites were the main factor in the adsorption process. Moreover, the maximum adsorption capacity (Q_m) reached 63.21 mg·g^-1 at 30 min at room temperature, which was better than most of the same type of adsorbents. The highly dispersed of LDHs anchored growth on EG overcame the disadvantage of aggregation, which exposed more adsorption sites and improved the removal efficiency of F^-. In addition, the effects of pH, anion interference, different water quality, and regeneration tests on the EG/LDHs composites were also analyzed, showing that the composites have good stability.

Potential Mechanism of Long-Term Immobilization of Pb/Cd by Layered Double Hydroxide Doped Chicken-Manure Biochar

Layered double hydroxide (LDH)-doped chicken-manure biochar (CMB) with long-term stability was synthesized to immobilize Pb/Cd. MgAl-Cl-LDH-doped CMB (MHs) showed prominent long-term oxidation resistance and the least biodegradation sensitivity. Efficient Pb/Cd adsorption was observed on MHs, and the maximum adsorption capacities of Pb(II)/Cd(II) reached 1.95 mmol/g and 0.65 mmol/g, respectively. Precipitation and isomorphous substitution were identified as the key adsorption mechanisms, which formed highly stable Pb/Cd species (PbAl-CO₃-LDH, Pb₃(OH)₂CO₃, CdAl-Cl-LDH and CdCO₃). Pb(II) and Cd(II) precipitated with CO₃^2- in MHs; meanwhile, Mg(II) and Ca(II) in LDH layers were substituted by Pb(II) and Cd(II) respectively. Therefore, MHs had the potential for long-term stability of Pb/Cd. Moreover, complexation and electrostatic adsorption also contributed to the Pb/Cd immobilization to a certain extent. When 5% MHs (w/w) was applied to Pb/Cd contaminated smelting site soils, the soil pH increased from 5.9 to 7.3. After applying MHs for 25 d, the content of bioavailable Pb(II) and Cd(II) decreased by 98.8% and 85.2%, respectively, and the content of soluble Pb and Cd dropped by 99.5% and 96.7%. This study paves the way for designing a novel LDH doped CMB as efficient Pb/Cd immobilizers for smelting site soils.

Removal efficiency of As(III) from aqueous solutions using natural and Fe(III) modified bentonites

Contamination of water with arsenic is a major global health problem. The use of adsorbent materials for the removal of As from aqueous systems is a plausible solution to this problem. In this work, the use of commercial bentonites (purified and modified with iron (III)) for the removal of As from water was studied. The samples were characterized by X-ray fluorescence (XRF), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier Transformed Infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and nitrogen adsorption/desorption isotherms to determine their physicochemical properties. The arsenic removal capacities of adsorbent materials were studied from 1 mg/L solutions of As (III) using the colorimetric technique of molybdenum blue. High adsorption capacity (0.33 mg/g) of As (III) was obtained in aqueous systems after 1 h of treatment with unmodified bentonite. The incorporation of iron improved the removal performance in short times. The obtained results could be the starting point for the development of a low-cost filtration system that contributes to solve the problem of arsenic in water.

The role of doped-Mn on enhancing arsenic removal by MgAl-LDHs

To meet the challenges posed by global arsenic water contamination, the MgAlMn-LDHs with extraordinary efficiency of arsenate removal was developed. In order to clarify the enhancement effect of the doped-Mn on the arsenate removal performance of the LDHs, the cluster models of the MgAlMn-LDHs and MgAl-LDHs were established and calculated by using density functional theory (DFT). The results shown that the doped-Mn can significantly change the electronic structure of the LDHs and improve its chemical activity. Compared with the MgAl-LDHs that without the doped-Mn, the HOMO-LUMO gap was smaller after doping. In addition, the -OH and Al on the laminates were also activated to improve the adsorption property of the LDHs. Besides, the doped-Mn existed as a novel active site. On the other hand, the MgAlMn-LDHs with the doped-Mn, the increased of the binding energy, as well as the decreased of the ion exchange energy of interlayer Cl^-, making the ability to arsenate removal had been considerably elevated than the MgAl-LDHs. Furthermore, there is an obvious coordination covalent bond between arsenate and the laminates of the MgAlMn-LDHs that with the doped-Mn.

Molecular scale assessment of defluoridation of coal-mining wastewater by calcined Mg/Al layered double hydroxide using 19F solid-state NMR, XPS, and HRTEM

Calcination is an effective way to improve the F^- adsorption capacity of layered double hydroxide (LDH) materials, however, a molecular scale understanding of the enhanced defluoridation capability of calcined LDHs (CLDH) is lacking. This study investigated the mechanisms of F^- adsorption by CLDH using ¹⁹F solid-state NMR, X-ray photoelectron spectroscopy (XPS), and high-resolution TEM. Under calcination process, LDH underwent three periods: surface dehydration below 200 °C, structural dehydroxylation at 200-400 °C, and release of interlayer carbonate groups above 400 °C. Additionally, XPS and XRD characterization showed that CLDH could not recover to the original structural symmetry even after rehydration and reconstitution. The F^- affinity was greatly enhanced for the calcined LDH, especially at high pH. At pH 10, the adsorption capacity could reach 22.0 mg F^-/g for CLDH (500 °C calcined), about 6 times larger than that of LDH. The XRD analyses revealed that the F-adsorbed CLDH had a poorer crystalline degree as the calcination temperature increased, consistent with the TEM observation of abundant defects and Mg/Al oxides on the CLDH sheets. ¹⁹F solid-state NMR spectra of the CLDH after F^- adsorption showed that the formation of surface Al-F is the predominant F^- adsorption mode at pH 7, whereas the Mg-F local coordination mode is the pronounced F^- adsorption mechanism under alkaline conditions (pH 10). The present study provided a comprehensive understanding of CLDH in F^- adsorption and suggested that calcination is a promising treatment for promoting the efficacy of polluted anion scavenging.

Efficient Vanadate Removal by Mg-Fe-Ti Layered Double Hydroxide

A series of novel layered double hydroxides (Mg-Fe-Ti-LDHs) containing Mg2+, Fe3+ and Ti4+ were prepared. The adsorption performance of Mg-Fe-Ti-LDHs on vanadate in aqueous solution was investigated and the effects of various factors on the adsorption process were examined, including initial vanadate concentration, adsorbent dosage, contact time, solution pH and coexisting ions. A preliminary discussion of the adsorption mechanism of vanadate was also presented. Results show that the adsorption efficiency of vanadate increased with the introduction of Ti4+ into the laminate of LDHs materials. The adsorption capacity of the materials also differed for different anion intercalated layers, and the Mg-Fe-Ti-LDHs with Cl− intercalation showed higher vanadate removal compared to the CO32− intercalated layer. Furthermore, Mg-Fe-Ti-CLDH showed higher vanadate removal compared to pre-calcination. The adsorption experimental data of vanadate on Mg-Fe-Ti-LDHs were consistent with the Langmuir adsorption isotherm model and the adsorption kinetics followed a pseudo-second order kinetic model. The pH of the solution significantly affected the vanadate removal efficiency. Meanwhile, coexisting ions PO43−, SO42− and NO3− exerted a significant influence on vanadate adsorption, the magnitude of the influence was related to the valence state of the coexisting anions. The possible adsorption mechanisms can be attributed to ion exchange and layered ligand exchange processes. The good adsorption capacity of Mg-Fe-Ti-LDHs on vanadate broadens the application area of functional materials of LDHs.

Single-step removal of arsenite ions from water through oxidation-coupled adsorption using Mn/Mg/Fe layered double hydroxide as catalyst and adsorbent

This study developed a layered double hydroxides (Mn/Mg/Fe-LDH) material through a simple co-precipitation method. The Mn/Mg/Fe-LDH oxidized arsenite [As(III)] ions into arsenate [As(V)] anions. The As(III) and oxidized As(V) were then adsorbed onto Mn/Mg/Fe-LDH. The adsorption process of arseniate [As(V)] oxyanions by Mn/Mg/Fe-LDH was simultaneously conducted for comparison. Characterization results indicated that (i) the best Mg/Mn/Fe molar ratio was 1/1/1, (ii) Mn/Mg/Fe-LDH structure was similar to that of hydrotalcite, (iii) Mn/Mg/Fe-LDH possessed a positively charged surface (pH_IEP of 10.15) and low Brunauer-Emmett-Teller surface area (S_BET = 75.2 m²/g), and (iv) Fe²⁺/Fe³⁺ and Mn²⁺/Mn³⁺/Mn⁴⁺ coexisted in Mn/Mg/Fe-LDH. The As(III) adsorption process by Mn/Mg/Fe-LDH was similar to that of As(V) under different experimental conditions (initial solutions pH, coexisting foreign anions, contact times, initial As concentrations, temperatures, and desorbing agents). The Langmuir maximum adsorption capacity of Mn/Mg/Fe-LDH to As(III) (56.1 mg/g) was higher than that of As(V) (32.2 mg/g) at pH 7.0 and 25 °C. X-ray photoelectron spectroscopy was applied to identify the oxidation states of As in laden Mn/Mg/Fe-LDH. The key removal mechanism of As(III) by Mn/Mg/Fe-LDH was oxidation-coupled adsorption, and that of As(V) was reduction-coupled adsorption. The As(V) mechanism adsorption mainly involved: (1) the inner-sphere and outer-sphere complexation with OH groups of Mn/Mg/Fe-LDH and (2) anion exchange with host anions (NO₃^-) in its interlayer. The primary mechanism adsorption of As(III) was the inner-sphere complexation. The redox reactions made Mn/Mg/Fe-LDH lose its original layer structure after adsorbing As(V) or As(III). The adsorption process was highly irreversible. Mn/Mg/Fe-LDH can decontaminate As from real groundwater samples from 45-92 ppb to 0.35-7.9 ppb (using 1.0 g/L). Therefore, Mn/Mg/Fe-LDH has great potential as a material for removing As.

Stability Trends in Mono-Metallic 3d Layered Double Hydroxides

Layered double hydroxides (LDHs) constitute a unique group of 2D materials that can deliver exceptional catalytic, optical, and electronic performance. However, they usually suffer from low stability compared to their oxide counterparts. Using density functional calculations, we quantitatively demonstrate the crucial impact of the intercalants (i.e., water, lactate, and carbonate) on the stability of a series of common LDHs based on Mn, Fe, and Co. We found that intercalation with the singly charged lactate results in higher stability in all these LDH compounds, compared to neutral water and doubly charged carbonate. Furthermore, we show that the dispersion effect aids the stability of these LDH compounds. This investigation reveals that certain intercalants enhance LDH stability and alter the bandgap favourably.

Comparison of Zn-Al and Mg-Al layered double hydroxides for adsorption of perfluorooctanoic acid

Per-and polyfluoroalkyl substances (PFAS), a large class of synthesized chemicals, are persistent in nature and generally recalcitrant to conventional chemical and biological treatment. Adsorption is considered an economical and practical method for PFAS treatment. Layered double hydroxides (LDHs) represent a promising class of mineral-based adsorbents for PFAS removal because of the highly positive charge of their structural layers. In this research, the performance of two representative LDHs with varied cation compositions, namely Zn-Al and Mg-Al LDHs, were investigated and compared for the removal of perfluorinated carboxylic acids (PFCAs) with an emphasis on perfluorooctanoic acid (PFOA). Zn-Al LDH showed high efficiency for the removal of medium- and long-chain PFCAs (i.e., C ≥ 7), and performed consistently better than Mg-Al LDH. Based on detailed adsorption kinetics and isotherm studies toward PFOA, Zn-Al LDH showed higher adsorption capacity, stronger adsorption affinity, and faster kinetics than Mg-Al LDH. Presence of natural organic matter had minimal impact on PFOA removal by Zn-Al LDH, but sulfate severely inhibited PFOA adsorption. Combined results of aqueous adsorption experiments and sorbent characterization suggested that electrostatic interactions may be the primary mechanism for PFOA adsorption onto LDHs. Our results suggested that cation composition of LDHs can have significant effect on the performance for PFCA removal.

High efficient arsenic removal by In-layer sulphur of layered double hydroxide

High-risk arsenic contamination found in aqueous system is reported across the world and causing severe environmental issues. In this study, the Mg-Al Layered Double Hydroxide (LDH) modified by sulphur species (LDH-S) was found exhibiting high effectivity and selectivity in As(V) removal owing to the strong interaction between embedded HS^- and AsO₄^3-. The LDH-S with Mg to Al ratio 2-1 give the best performance with As(V) adsorption capacity 40.8 mg/g, which is 715% higher than that of pristine LDH (2-1). The adsorbent exhibits a high tolerance to concentrated competitive anions. In the continuous flow test, the adsorbent can reduce the As(V) concentration from 20 ppm to below-ppb-level indicating the potential in industry application. The adsorption mechanism is experimentally investigated and examined by Density Function Theory (DFT) calculation. The result illustrates that, differ from the traditional ion exchange mechanism of LDH, the enhanced removal capacity and selectivity of LDH-S for As(V) is attributed to the strong affinity between H atom from HS- ion (in the interlayer region of LDH) and the O atom from AsO₄^3-.

Application of layered double hydroxide-biochar composites in wastewater treatment: Recent trends, modification strategies, and outlook

In recent years, layered double hydroxide-biochar (LDH-BC) composites as adsorbents and catalysts for contaminants removal (inorganic anions, heavy metals, and organics) have received increasing attention and became a new research point. It is because of the good chemical stability, abundant surface functional groups, excellent anion exchange ability, and good electronic properties of LDH-BC composites. Hence, we offer an overall review on the developments and processes in the synthesis of LDH-BC composites as adsorbents and catalysts. Special attention is devoted to the strategies for enhancing the properties of LDH-BC composites, including (1) magnetic treatment, (2) acid treatment, (3) alkali treatment, (4) controlling metal ion ratios, (5) LDHs intercalation, and (6) calcination. In addition, further studies are called for LDH-BC composites and potential areas for future application of LDH-BC composites are also proposed.

Preparation of adsorbent based on water treatment residuals and chitosan by homogeneous method with freeze-drying and its As(V) removal performance

Although the chitosan-WTRs particulate adsorbent prepared by embedding method has been proved to have arsenic adsorption capacity, the capacity of it is greatly weakened compared with the original water treatment residuals (WTRs). In this study, WTRs and chitosan were used as raw materials to prepare a new kind of adsorbent beads by a homogeneous method. At the same time, in order to enhance the adsorption capacity and reduce the limitation of kinetics, freeze-drying method was chosen to dry the adsorbent. The WTRs-chitosan beads by homogeneous method (WCB) were characterized by SEM, XRD, XPS and other methods. According to the characterization results, there are regularly arranged pores inside the particles, and the iron in the particles mainly exists in the form of amorphous iron oxyhydroxide. According to the results of batch experiment, the pseudo-second-order kinetic model has a higher degree of fit, indicating that the WCB adsorbs As(V) mainly by chemical adsorption. The maximum adsorption capacity estimated from the Langmuir isotherm model is 42.083 mg/g, which is almost same as the WTRs. Weak acid and neutral conditions are conducive to adsorption, while alkaline conditions have a significant inhibitory effect on arsenic adsorption.

Adsorptive Removal of Low-Concentration Cr(VI) in Aqueous Solution by Mg-Al Layered Double Oxides

To explore the adsorption removal mechanism of Mg-Al layered double oxides (LDOs) for low-concentration (≤ 5 mg L^-1) Cr(VI), the adsorption kinetics, adsorption isotherms and its influencing factors were studied by batch experiments. Cr(VI) adsorption reached equilibrium after 6, 11 and 15 h for initial Cr(VI) concentrations of 1, 3 and 5 mg L^-1, respectively, and the final adsorption efficiency exceeded 99.0%. The residual concentration of Cr(VI) was within the allowable limit of Drinking Water Quality Standard of World Health Organization (0.05 mg L^-1). The experimental data fitted the pseudo-second-order and Freundlich models well. Mg-Al LDOs showed effective adsorption efficiency in the range of pH 3-9, and the adsorption efficiency was influenced by anions competition (HPO₄^2- > SO₄^2- > CO₃^2- > NO₃^- > Cl^-). The analyses of XRD, SEM and FT-IR spectra suggested adsorption Cr(VI) on Mg-Al LDOs was caused by capturing dichromate ions to reconstruct its structure. Therefore, Mg-Al LDOs is promising adsorbents for the low-concentration Cr(VI) treatment in polluted surface water and groundwater.

Mn-Fe Layered Double Hydroxide Intercalated with Ethylene-Diaminetetraacetate Anion: Synthesis and Removal of As(III) from Aqueous Solution around pH 2-11

A novel adsorbent Mn-Fe layered double hydroxides intercalated with ethylenediaminete-traacetic (EDTA@MF-LDHs) was synthesized by a low saturation coprecipitation method. The behavior and mechanism of As(III) removed by EDTA@MF-LDHs were investigated in detail in comparison with the carbonate intercalated Mn-Fe layered double hydroxides (CO₃@MF-LDHs). The results showed that EDTA@MF-LDHs had a higher removal efficiency for As(III) than As(V) with a broader pH range than CO₃@MF-LDH. The large adsorption capacity of EDTA@MF-LDHs is related to its large interlayer spacing and the high affinity of its surface hydroxyl groups. The maximum adsorption capacity for As(III) is 66.76 mg/g at pH 7. The FT-IR and XPS characterization indicated that the removal mechanism of the As(III) on EDTA@MF-LDHs include surface complexation, redox, and ion exchange.

Faradaic Electrodes Open a New Era for Capacitive Deionization

Capacitive deionization (CDI) is an emerging desalination technology for effective removal of ionic species from aqueous solutions. Compared to conventional CDI, which is based on carbon electrodes and struggles with high salinity streams due to a limited salt removal capacity by ion electrosorption and excessive co-ion expulsion, the emerging Faradaic electrodes provide unique opportunities to upgrade the CDI performance, i.e., achieving much higher salt removal capacities and energy-efficient desalination for high salinity streams, due to the Faradaic reaction for ion capture. This article presents a comprehensive overview on the current developments of Faradaic electrode materials for CDI. Here, the fundamentals of Faradaic electrode-based CDI are first introduced in detail, including novel CDI cell architectures, key CDI performance metrics, ion capture mechanisms, and the design principles of Faradaic electrode materials. Three main categories of Faradaic electrode materials are summarized and discussed regarding their crystal structure, physicochemical characteristics, and desalination performance. In particular, the ion capture mechanisms in Faradaic electrode materials are highlighted to obtain a better understanding of the CDI process. Moreover, novel tailored applications, including selective ion removal and contaminant removal, are specifically introduced. Finally, the remaining challenges and research directions are also outlined to provide guidelines for future research.

A colloid chemistry route for the preparation of hierarchically ordered mesoporous layered double hydroxides using surfactants as sacrificial templates

An efficient synthetic route was developed to prepare hierarchically ordered mesoporous layered double hydroxide (LDH) materials. Sodium dodecyl sulfate (SDS) was used as a sacrificial template to tune the interfacial properties of the LDH materials during the synthetic process. The SDS dose was optimized to obtain stable dispersions of the SDS-LDH composites, which were calcined, then rehydrated to prepare the desired LDH structures. Results of various characterization studies revealed a clear relationship between the colloidal stability of the SDS-LDH precursors and the structural features of the final materials, which was entirely SDS-free. A comparison to the reference LDH prepared by the traditional co-precipitation-calcination-rehydration method in the absence of SDS shed light on a remarkable increase in the specific surface area (one of the highest within the previously reported LDH materials) and pore volume as well as on the formation of a beneficial pore size distribution. As a proof of concept, the mesoporous LDH was applied as adsorbent for removal of nitrate and dichromate anions from aqueous samples, and excellent efficiency was observed in both sorption capacity and recyclability. These results make the obtained LDH a promising candidate as adsorbent in various industrial and environmental processes, wherever the use of mesoporous and organic content-free materials is required.

Improved performance of 3D hierarchical NiAl-LDHs micro-flowers via a surface anchored ZIF-8 for rapid multiple-pollutants simultaneous removal and residues monitoring

In this paper, we report a new type of 3D ZIF-8@NiAl-LDHs micro-flowers material consisting of sandwich-like structured 2D nanopetals (highly compact ZIF-8 film anchored on both sides of petals). ZIF-8 was successfully incorporated into NiAl-LDHs (ZIF-8@NiAl-LDHs) via seeding strategy directed growth of ZIFs on the surface of LDHs nanopetals. The coating of ZIF-8 significantly increased the adsorption ability to organic pollutants and inorganic cation. 3D ZIF-8@NiAl-LDHs with excellent enrichment and filtration properties has been exploited for the application in water purification, and exhibit superior high adsorption rate and adsorption efficiency of organic (nonsteroidal anti-inflammatory drugs: ketoprofen, flurbiprofen, indometacin and ibuprofe; anionic dyes: congo red, orange g; cationic dyes: methylene blue, rhodamine b) and inorganic cation (Cu²⁺, Pb²⁺) residues due to their novel hierarchical and submicroscopic structures. Further, 3D ZIF-8@NiAl-LDHs as filter membrane to extraction four kind of trace anti-inflammatory drugs followed by direct quantification detection of targets with HPLC was demonstrated. The validated method was successfully applied for analysis of four anti-inflammatory drugs in environmental water and human urine samples. This work provided a feasible way to design and construct purification materials for wastewater treatment and contaminant detection.

Remediation of carcinogenic arsenic by pyroaurite-based green adsorbent: isotherm, kinetic, mechanistic study, and applicability in real-life groundwater

The removal of the harmful carcinogen arsenic from drinking water by a green technology is a major concern in the field of environmental engineering. The sorptive profile of arsenic remediation by calcined Mg-Fe-layered double hydroxide, fabricated by a one-pot synthesis technique, was investigated to delineate its applicability in real-life water. The physicochemical properties of adsorbent, as demonstrated from spectroscopy and microscopy, which described the existence of amorphous material with significant surface roughness possess selectivity towards arsenic. The isotherm and kinetic along with thermodynamic modeling exhibited the occurrence of spontaneous (ΔG⁰ value = - 8.084 kJ/mol to - 10.942 kJ/mol), endothermic (ΔH⁰ value = 12.135 kJ/mol), and physisorption reactions (E_ad = 4.103-5.832 kJ/mol, E_a = 11.546 kJ/mol, S* = 0.0005 << 1, and ΔH_x = 9.23-16.29 kJ/mol) with high uptake rate and adsorption potential of adsorbent. The isotherm and kinetics were demonstrated by Temkin (R² = 0.944-0.969) and Elovich (R² = 0.996-0.998) models, respectively, with high statistical significance. The intraparticle diffusion model which established the rate-limiting step is the combination of both film and pore diffusions. The applicability of layered double hydroxide (LDH) material in the real-life water was confirmed by isotherm and kinetic modeling along with the regeneration/reuse potential. The adsorptive removal of arsenic by the LDH material exhibited to be a promising technique without creating any secondary hazard.

Synthesis of novel adsorbent by intercalation of biopolymer in LDH for the removal of arsenic from synthetic and natural water

This study focuses on the synthesis of nanocomposites named CCA and CZA that were prepared by the incorporation of cellulose (CL) in the Ca/Al and Zn/Al layered double hydroxide (LDH), respectively. These materials were then used for the uptake of As(III) and As(V) from aqueous medium. Characterization of both nanocomposites (CCA and CZA) was done using FTIR and Raman analysis to identify the functional groups, N₂ adsorption-desorption isotherms to determine the specific surface area and pore geometry and XPS analysis to obtain the surface atomic composition. Some other characters were investigated using simultaneous TGA and DTA and elemental chemical analysis (CHNS/O). The crystallinity of the prepared nanocomposites was displayed by XRD patterns. Furthermore, the sheet-like structure of the LDHs and the irregularity of surface morphology with porous structure were observed by TEM and SEM microphotographs. Optimization of maximum adsorption capacity was adjusted using different parameters including pH, contact time and adsorbent dosage. The pseudo-second-order model was in good fitting with kinetics results. The adsorption isotherm results showed that CZA exhibits better adsorption capacity for As(III) than CCA and the Langmuir isotherm model described the data well for both nanocomposites. Thermodynamic studies illustrated the endothermic nature of CCA and exothermic nature on CZA, as well as the fact that the adsorption process is spontaneous. A real water sample collected from well located in Gabes (Tunisia), has also been treated. The obtained experimental results were confirmed that these sorbents are efficient for the treatment of hazardous toxic species such as.

Fast and efficient aqueous arsenic removal by functionalized MIL-100(Fe)/rGO/δ-MnO2 ternary composites: Adsorption performance and mechanism

Because of its significant toxicological effects on the environment and human health, arsenic (As) is a major global issue. In this study, an Fe-based metal-organic framework (MOF) (Materials of Institut Lavoisier: MIL-100 (Fe)) which was impregnated with reduced graphene oxide (rGO) by using a simple hydrothermal method and coated with birnessite-type manganese oxide (δ-MnO₂) using the one-pot reaction process (MIL-100(Fe)/rGO/δ-MnO₂ nanocomposites) was synthesized and applied successfully in As removal. The removal efficiency was rapid, the equilibrium was achieved in 40 min and 120 min for As(III) and As(V), respectively, at a level of 5 mg/L. The maximum adsorption capacities of As(III) and As(V) at pH 2 were 192.67 mg/g and 162.07 mg/g, respectively. The adsorbent revealed high stability in pH range 2-9 and saturated adsorbent can be fully regenerated at least five runs. The adsorption process can be described by the pseudo-second-order kinetic model and Langmuir monolayer adsorption. The adsorption mechanisms consisted of electrostatic interaction, oxidation and inner sphere surface complexation.

A review on the preparation, characterization and potential application of perovskites as adsorbents for wastewater treatment

Perovskite are among the popular materials utilized in many areas of modern industrialization because of their low price, high stability, excellent oxidation activity, adsorptive, catalytic, optical, magnetic, electronic and ferroelectric properties. Over the years, widespread usage of perovskite nanoparticles has been reported due to its various applications which include an environmental catalyst, fuel cells, chemical sensors, magnetic materials, oxygen permeable membranes and adsorbents for wastewater treatment. Various synthetic methods such as the sol-gel method, proteic method, Pechini method, combustion, co-precipitation, and chelating precursor method have been applied in producing perovskites. Therefore, this review assembles the current knowledge on the processes involved in the preparation of perovskites, their characterizations and potential applications in wastewater treatment. Challenges and future opportunities of perovskite-based materials are discussed as well as obstacles against their extensive uses. Conclusions have also been drawn proposing a few suggestions for future research.

Developing a novel packed in-tube solid-phase extraction method for determination ∆ 9-tetrahydrocannabinol in biological samples and cannabis leaves

A novel plate-like nano-sorbent based on copper/cobalt/chromium layered double hydroxide was synthesized by a simple coprecipitation method. The synthesized nanoparticels were introduced into a stainless steel cartridge using a dry packing method. Then, the packed cartridge was introduced as a novel on-line "packed in-tube" configuration and followed by high performance liquid chromatography for the determination of trace amounts of ^∆ 9-tetrahydrocannabinol from biological samples and cannabis leaves. The as-prepared sorbent exhibited long lifetime, good chemical stability, and high anion-exchange capacity. Several important factors affecting the extraction efficiency, such as extraction and desorption times, pH of the sample solution and flow rates of the sample and eluent solutions, were investigated and optimized. Under optimized conditions, this method showed good linearity for ^∆ 9-tetrahydrocannabinol in the ranges of 0.09-500, 0.3-500, and 0.4-500 µg/L with coefficients of determination of 0.9999, 0.9991, and 0.9994 in water, serum and plasma samples, respectively. The inter- and intra-assay precisions (n = 3) were respectively in the ranges of 1.8-4.6% and 1.9-4.0% at three concentration levels of 10, 50, and 100 µg/L. The limits of detection were also in the range of 0.02-0.1 µg/L.

Interaction of U(vi) with α-MnO2@layered double hydroxides by combined batch experiments and spectroscopy studies

Uranium is of high concern in the field of environmental remediation because of its high fluidity, radioactivity, biological toxicity and long life. Removing U(vi) from wastewater is of great significance to both environment and biology.

An experimental approach for determining thermodynamic surface complexation descriptors of weak-acid oxyanions onto metal (hydr)oxides: Case study of arsenic and titanium dioxide

The extensive literature review suggests that there are two main reasons for contradictory thermodynamic parameter values obtained via sorption experiments: (1) many of the studies are conducted under unrealistic conditions where the sorbate/sorbent ratios are so high that physisorption is artificially induced; or (2) many of the studies incorrectly calculate the equilibrium constants. The goal of this study is to demonstrate a methodology that describes how to properly determine and verify theoretically predicted thermodynamic descriptors. The study employs arsenate and titanium dioxide as a model sorbate-sorbent pair, which is equilibrated under realistic conditions for a period of 3 days at two different pH conditions (~6.5 and ~8.5) and three different temperatures (7 °C, 25 °C and 35 °C) in 10 mM NaHCO₃. At pH ≈ 8.55, ΔG^o values were -83.38 ± 1.62 kJ/mol, -88.13 ± 0.66 kJ/mol, and -90.78 ± 0.61 kJ/mol for sorption performed at 7 °C, 25 °C and 35 °C, respectively. Decreasing the pH to about 6.65 resulted in slightly less negative values of ΔG^o to -73.38 ± 1.58 kJ/mol, -77.14 ± 1.52 kJ/mol, and -78.75 ± 1.53 kJ/mol for sorption conducted at the same respective temperature conditions. These values overlap with the ΔG^o ranges reported for sorption of arsenate on metal oxides. Change in enthalpy values of ΔH^o = -19.04 kJ/mol at pH ≈ 6.65 and ΔH^o =-9.35 kJ/mol at pH ≈ 8.55 were observed. Based on reports, which suggest that at lower pH more bidentate ligands are being formed, these values are expected. The change in entropy values ranged from ΔS^o = 0.19 kJ/mol K at pH ≈ 6.55 to ΔS^o = 0.26 kJ/mol K at pH ≈ 8.55, which suggests lower level of disorder among the created complexes at lower pH and it is in line with the rationale that bidentate complexes are better organized on the surface of the sorbent and less susceptible with desorption. These findings clearly demonstrate that experimentally obtained ΔG⁰ and other thermodynamic values and trends could be obtained to reflect and confirm model predictions when the existing sorption theory is properly translated into experimental practice. The sorbate-sorbent bond in chemisorption has covalent character, characterized with short bond length and higher bond energy, which makes it less reversible when compared to physisorption, and therefore highly significant from a sorbent remediation-performance practical point of view and long-term waste sorbents disposal. While thermodynamic parameter modeling represents a good first step in determining the suitability of an initial design, experimental techniques potentially have the ability to provide far more superior description of the thermodynamic sorbent/sorbate interactions under realistic conditions.

Antimonate adsorption onto Mg-Fe layered double hydroxides in aqueous solutions at different pH values: Coupling surface complexation modeling with solid-state analyses

In this study, the importance of Sb behavior under different pH conditions has been addressed with respect to its stabilization in aqueous solutions using Mg-Fe layered double hydroxides (LDHs). The Sb(V) adsorption onto Mg-Fe LDHs was performed at different initial Sb(V) concentrations and pH values (pH 5.5, 6.5 and 7.5). The removal rate and the maximal adsorbed amount increased with decreasing pH values. Moreover, the surface complexation modeling (SCM) predicted preferable formation of monodentate mononuclear and bidentate binuclear complexes on the Mg-Fe LDH surface. Spectroscopic (X-ray diffraction analysis, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy) and microscopic (scanning electron microscopy and energy-dispersive X-ray spectroscopy) techniques were used to further specify the adsorption mechanisms. The influence of chemical adsorption, surface-induced precipitation of brandholzite Mg[Sb(OH)₆]₂·6H₂O, formation of brandholzite-like phases and/or anion exchange was observed. Moreover, Sb(V) was nonhomogeneously distributed on the Mg-Fe LDH surface at all pH values. The surface complexation modeling supported by solid-state analyses provided a strong tool to investigate the binding arrangements of Sb(V) on the Mg-Fe LDH surface. Such a complex mechanistic/modeling approach has not previously been presented and enables prediction of the Sb(V) adsorption behavior onto Mg-Fe LDHs under different conditions, evaluating their possible use in actual applications.

Enhanced arsenite removal from water by radially porous Fe-chitosan beads: Adsorption and H2O2 catalytic oxidation

Although Fe-chitosan adsorbents are attractive for removing arsenite from water, the practical applications of these granular adsorbents are mainly limited by slow adsorption kinetics. In this study, radially porous Fe-chitosan beads (P/Fe-CB) were prepared using freeze-casting technique. The P/Fe-CB particles possess radially aligned micron-sized tunnels from the surface to the inside as well as excellent acid resistance. Kinetic studies show that the adsorption equilibrium time of P/Fe-CB to 0.975 mg/L As(III) (within 240 min) is considerably shorter than that of compact Fe-chitosan beads (over 600 min). The maximal adsorption capacity of P/Fe-CB for As(III) is 52.7 mg/g. It can work effectively in a wide pH range from 3 to 9, and the coexisting sulfate, carbonate, silicate and humic acid have no significant effect on As(III) removal. The addition of H₂O₂ can further accelerate and promote the As(III) removal except at high pH (11) and phosphate concentration (50 mg/L). The fixed-bed experiments demonstrate that the P/Fe-CB column can effectively treat about 3000 bed volume (BV) of simulated As(III)-containing groundwater to meet the drinking water standard (<10 μg As/L). This study would extend the potential applicability of porous Fe based chitosan adsorbent and millimeter-sized adsorbent combined with H₂O₂ to a great extent.

Fast and efficient removal of As(III) from water by CuFe2O4 with peroxymonosulfate: Effects of oxidation and adsorption

Although oxidation of As(III) to As(V) is deemed necessary to promote arsenic removal, the oxidation process usually involves toxic byproducts, well-defined conditions, energy input or sludge generation. Moreover, extra operations are required to remove the resulting As(V). A heterogeneous catalytic process of CuFe₂O₄ with peroxymonosulfate (PMS) is established for As(III) oxidation and adsorption. The PMS can be activated by CuFe₂O₄ to generate radical species for As(III) oxidation. The CuFe₂O₄/PMS has a stronger affinity for arsenic than CuFe₂O₄ alone. Oxidation and adsorption promote each other. As a result, the heterogeneous catalytic process is more efficient for As(III) removal than a preoxidation of As(III) followed by adsorption. The adsorption capacity for As on CuFe₂O₄/PMS reached up to 63.9 mg/g, which is much higher than that of As(III) (36.9 mg/g) or As(V) (45.4 mg/g) on CuFe₂O₄ alone. The process can work effectively over a wide range of pH values (3-9) and temperatures (10-40 °C). Coexisting ions such as sulfate, carbonate, silicate and humic acid have an insignificant effect on As(III) removal. The As(III) (1415 μg/L) can be completely oxidized to As(V) and rapidly removed to below 10 μg/L (less than 15 min) using CuFe₂O₄(0.2 g/L)/PMS(100 μM). Moreover, the As(III) (50 μg/L) can be completely oxidized and removed within 1 min. The proposed process is easily applicable for the remediation of As(III)-contaminated water under ambient conditions.

Structural substitution for SO4 group in tooeleite crystal by As(V) and As(III) oxoanions and the environmental implications

Two different SO₄-free tooeleite were prepared for the first time through structural substitution for SO₄ group by As(V) and As(III). As(III)-tooeleite and As(V)-tooeleite have similar crystalline structure to SO₄-tooeleite but incorporate different anions in the interlayer space. The removal of As can reach 94% by forming SO₄-free tooeleite crystals, and As leaching in TCLP tests can be much lower than that of SO₄-tooeleite. Therefore, SO₄-free tooeleite crystals are of great potential in As removal and immobilization. Moreover, our study indicates the different affinities of Fe(III) towards As(III), As(V) and SO₄, which can explain that a) the coordination structure of As(III)-tooeleite is much closer to the ideal crystal structure but easily affected by As(V) and SO₄ group; b) tooeleite mineral found in natural environments is commonly a SO₄-containing mineral and associated with scorodite due to the abundance of As(V) and SO₄ group.

Enhanced adsorption of arsenate and antimonate by calcined Mg/Al layered double hydroxide: Investigation of comparative adsorption mechanism by surface characterization

This study aims to investigate adsorption mechanisms of As(V) and Sb(V) on calcined Mg/Al layered double hydroxide (LDH). The calcination process of Mg/Al LDH (CLDH) considerably enhanced the adsorption capacity of As(V) and Sb(V) via reconstruction and new formation of brandholzite-like compound, respectively. The maximum adsorption capacity for As(V) and Sb(V) by CLDH was 102.9 mg/g and 303.3 mg/g, respectively. The regeneration efficiency of As(V) by 0.5 M NaOH with 5 M NaCl mixed solution reached 72.3% during five regeneration cycles, while Sb(V) regeneration gradually decreased to 32.0% at the fifth regeneration cycles due to the irreversible surface complexation mechanism. Extended X-ray absorption fine structure (EXAFS) data displayed that Al plays a dominant role in the adsorption of As(V) on CLDH through bidentate-binuclear inner-sphere complex. On the other hand, XRD and EXAFS data revealed that Sb(V) formed a brandholzite-like structure Mg[Sb(OH)₆]₂·6H₂O which forms outer-sphere complex by the hydrogen bonding between hexagonal plates of magnesium and antimony hydroxide. Although the formation of brandholzite-like structure causes the partial transformation of original structure of Mg/Al LDH during reconstruction process with decreasing regeneration efficiency, it could be attributed to high binding affinity between Sb(V) and Mg/Al LDH.

Synthesis and characterization of an iron-impregnated biochar for aqueous arsenic removal

The iron (Fe)-impregnated biochar (FBC), fabricated via thermal pyrolysis of corn straw treated with FeCl₃, was investigated for the sorption characteristics and mechanisms of aqueous arsenate removal. Structural and morphological analysis showed that large quantity of iron oxide particles tightly grew within the porous matrix of biochar (BC) through iron-impregnation. Batch sorption experimental results showed that the composite, with larger surface area, more functional groups, and greater thermal stability, exhibited excellent As(V) adsorption efficiency of 6.80mg/g compared to 0.017mg/g for unmodified BC (a 400-fold increase). The adsorption kinetics data were fitted well by pseudo second-order model, and sorption isotherms of As(V) were simulated well by both Freundlich and Langmuir models. XRD and FTIR analysis suggested that electrostatic attraction and precipitation were dominant mechanisms for As(V) sorption. The As(V)-loaded FBC could be easily separated from the solution by a magnet at the end of the sorption experiment. The FBC showed excellent re-sorption capacity, which account for about 70% removal efficiency for the second and third reuse in As(V) sorption. Results from this study demonstrated the promise of FBC composite as an efficient, low-cost, environmentally friendly, and regenerable adsorbent for As(V) remediation.

CAPSULE

FBC showed enhanced As(V) sorption capacity, excellent re-sorption capacity, and could be easily separated by a magnet.

Using cobalt/chromium layered double hydroxide nano-sheets as a novel packed in-tube solid phase microextraction sorbent for facile extraction of acidic pesticides from water samples

Cobalt/chromium-layered double hydroxide (Co/Cr (NO₃⁻)-LDH) nano-sheets were employed as a packed in-tube solid phase microextraction sorbent for efficient extraction of acidic pesticides from water samples.

Enhanced Removal of Arsenic from Water by Synthetic Nanocrystalline Iowaite

Nanocrystalline iowaite, a Mg/Fe-based layered double hydroxide (LDH) intercalated with chloride, was synthesized to evaluate its performance for arsenic removal from water and to investigate the contributing dearsenication mechanisms. It is characterized by fast arsenic sorption rates and has a much higher arsenic uptake capacity than other LDHs that are commonly used for water dearsenication. The surface adsorption of the solution arsenic onto the iowaite samples and the anion exchange of the arsenic in solution with chloride, which is originally in the iowaite interlayers, are the primary mechanisms for the uptake of arsenic by iowaite. In addition to the Coulombic attraction between arsenate/arsenite and positively charged layers of iowaite, the inner-sphere complexation of arsenic with Fe (instead of Mg) in the iowaite layers is responsible for the formation of more stable and stronger arsenic bonds, as indicated by both XPS and EXAFS analyses. Specifically, bidentate-binuclear and monodentate-mononuclear As-Fe complexes were detected in the arsenate removal experiments, whereas bidentate-mononuclear, bidentate-binuclear, and monodentate-mononuclear As-Fe complexes were present for the arsenite-treated iowaite samples. This study shows that nanocrystalline iowaite is a promising, low-cost material for arsenic removal from natural arsenic-rich waters or contaminated high-arsenic waters.

Highly selective and efficient removal of arsenic(V), chromium(VI) and selenium(VI) oxyanions by layered double hydroxide intercalated with zwitterionic glycine

In this study, a new strategy for highly selective and extremely efficient removal of toxic oxyanions (Cr(VI), Se(VI), and As(V)) from aqueous solutions using zwitterionic glycine intercalated layered double hydroxide (Gly-LDH) was reported. Hence, to investigate the effect of zwitterionic glycine on the adsorption capacity, selectivity factor and adsorption mechanism of LDHs, two NiAl LDHs intercalated with different inter-layer anions, including NO₃^- and glycine, were synthesized. The obtained results show that the adsorption capacity and selectivity factor of oxyanions through ion exchange mechanism in NO₃-LDH is lower than Gly-LDH. Gly-LDH displayed a selectivity order of Se(VI)<Cr(VI)<<<As(V) for the oxyanions. The enormous adsorption capacity of 731.6mgg^-1 for As(V) and very high distribution coefficients (K_d) of 5.98×10⁷mLg^-1, using a V/m ratio of 2000mLg^-1, were observed, which are among the highest values reported for As(V) adsorbents. The adsorption kinetic curves for As(V) fitted well with the pseudo-second order model, suggesting a chemical adsorption mechanism via As(V)NH₃⁺ bonding. For the As(V) (at 40mgL^-1 concentration), the adsorption is exceptionally rapid, showing a 93.5% removal within 30min, 98.0% removal within 40min, and ∼100% removal within 70min.

Selenium Sequestration in a Cationic Layered Rare Earth Hydroxide: A Combined Batch Experiments and EXAFS Investigation

Selenium is of great concern owing to its acutely toxic characteristic at elevated dosage and the long-term radiotoxicity of ⁷⁹Se. The contents of selenium in industrial wastewater, agricultural runoff, and drinking water have to be constrained to a value of 50 μg/L as the maximum concentration limit. We reported here the selenium uptake using a structurally well-defined cationic layered rare earth hydroxide, Y₂(OH)₅Cl·1.5H₂O. The sorption kinetics, isotherms, selectivity, and desorption of selenite and selenate on Y₂(OH)₅Cl·1.5H₂O at pH 7 and 8.5 were systematically investigated using a batch method. The maximum sorption capacities of selenite and selenate are 207 and 124 mg/g, respectively, both representing the new records among those of inorganic sorbents. In the low concentration region, Y₂(OH)₅Cl·1.5H₂O is able to almost completely remove selenium from aqueous solution even in the presence of competitive anions such as NO₃^-, Cl^-, CO₃^2-, SO₄^2-, and HPO₄^2-. The resulting concentration of selenium is below 10 μg/L, well meeting the strictest criterion for the drinking water. The selenate on loaded samples could be desorbed by rinsing with concentrated noncomplexing NaCl solutions whereas complexing ligands have to be employed to elute selenite for the material regeneration. After desorption, Y₂(OH)₅Cl·1.5H₂O could be reused to remove selenate and selenite. In addition, the sorption mechanism was unraveled by the combination of EDS, FT-IR, Raman, PXRD, and EXAFS techniques. Specifically, the selenate ions were exchanged with chloride ions in the interlayer space, forming outer-sphere complexes. In comparison, besides anion exchange mechanism, the selenite ions were directly bound to the Y³⁺ center in the positively charged layer of [Y₂(OH)₅(H₂O)]⁺ through strong bidentate binuclear inner-sphere complexation, consistent with the observation of the higher uptake of selenite over selenate. The results presented in this work confirm that the cationic layered rare earth hydroxide is an emerging and promising material for efficient removal of selenite and selenate as well as other anionic environmental pollutants.

Enhanced adsorption of bromate from aqueous solutions on ordered mesoporous Mg-Al layered double hydroxides (LDHs)

An ordered mesoporous Mg-Al layered double hydroxide (meso-LDH350) with a fairly high Brunauer-Emmett-Teller (BET) surface area (126m²g^-1) has been facilely synthesized and then evaluated for the adsorptive removal of bromate from aqueous solutions. Adsorbents were characterized by a variety of techniques (e.g., XRD, FTIR, SEM, TG-DSC, N₂ physisorption, XPS, etc.). The adsorption studies indicated that the presence of background electrolytes and competitive anions can obviously repress the uptake of bromate on LDHs. The adsorption isotherms agree well with the Langmuir model, giving a maximum adsorption capacity of 59.34mgg^-1 (pH 7.5, 10°C) for meso-LDH350, which is much higher than other LDH-type adsorbents reported in literature. The adsorption kinetic data can be well fitted with the pseudo-second-order rate model. Based on the macroscopic and microscopic studies, bromate adsorption on meso-LDH350 was associated with two mechanisms: the reconstruction of the layered structures of meso-LDH350 and the anion-exchange between bromate and the intercalated anions.