Behaviors and Effects of Differing Dimensional Nanomaterials in Water Filtration Membranes through the Classical Phase Inversion Process: A Review

Recent progress in nanomaterial-functionalized membranes for removal of pollutants

Membrane technology has gained tremendous attention for removing pollutants from wastewater, mainly due to their affordable capital cost, miniature equipment size, low energy consumption, and high efficiency even for the pollutants present in lower concentrations. In this paper, we review the literature to summarize the progress of nanomaterial-modified membranes for wastewater treatment applications. Introduction of nanomaterial in the polymeric matrix influences membrane properties such as surface roughness, hydrophobicity, porosity, and fouling resistance. This review also covers the importance of functionalization strategies to prepare thin-film nanocomposite hybrid membranes and their effect on eliminating pollutants. Systematic discussion regarding the impact of the nanomaterials incorporated within membrane, toward the recovery of various pollutants such as metal ions, organic compounds, dyes, and microbes. Successful examples are provided to show the potential of nanomaterial-functionalized membranes for regeneration of wastewater. In the end, future prospects are discussed to develop nanomaterial-based membrane technology.

Lignocellulosic Biomass-Derived Nanocellulose Crystals as Fillers in Membranes for Water and Wastewater Treatment: A Review

The improvement of membrane applications for wastewater treatment has been a focal point of research in recent times, with a wide variety of efforts being made to enhance the performance, integrity and environmental friendliness of the existing membrane materials. Cellulose nanocrystals (CNCs) are sustainable nanomaterials derived from microorganisms and plants with promising potential in wastewater treatment. Cellulose nanomaterials offer a satisfactory alternative to other environmentally harmful nanomaterials. However, only a few review articles on this important field are available in the open literature, especially in membrane applications for wastewater treatment. This review briefly highlights the circular economy of waste lignocellulosic biomass and the isolation of CNCs from waste lignocellulosic biomass for membrane applications. The surface chemical functionalization technique for the preparation of CNC-based materials with the desired functional groups and properties is outlined. Recent uses of CNC-based materials in membrane applications for wastewater treatment are presented. In addition, the assessment of the environmental impacts of CNCs, cellulose extraction, the production techniques of cellulose products, cellulose product utilization, and their end-of-life disposal are briefly discussed. Furthermore, the challenges and prospects for the development of CNC from waste biomass for application in wastewater treatment are discussed extensively. Finally, this review unraveled some important perceptions on the prospects of CNC-based materials, especially in membrane applications for the treatment of wastewater.

Instant in situ formation of a polymer film at the water–oil interface

The water–oil interface is an environment that is often found in many contexts of the natural sciences and technological arenas. This interface has always been considered a special environment as it is rich in different phenomena, thus stimulating numerous studies aimed at understanding the abundance of physico-chemical problems that occur there. The intense research activity and the intriguing results that emerged from these investigations have inspired scientists to consider the water–oil interface even as a suitable setting for bottom-up nanofabrication processes, such as molecular self-assembly, or fabrication of nanofilms or nano-devices. On the other hand, biphasic liquid separation is a key enabling technology in many applications, including water treatment for environmental problems. Here we show for the first time an instant nanofabrication strategy of a thin film of biopolymer at the water–oil interface. The polymer film is fabricated in situ, simply by injecting a drop of polymer solution at the interface. Furthermore, we demonstrate that with an appropriate multiple drop delivery it is also possible to quickly produce a large area film (up to 150 cm²). The film inherently separates the two liquids, thus forming a separation layer between them and remains stable at the interface for a long time. Furthermore, we demonstrate the fabrication with different oils, thus suggesting potential exploitation in different fields (e.g. food, pollution, biotechnology). We believe that the new strategy fabrication could inspire different uses and promote applications among the many scenarios already explored or to be studied in the future at this special interface environment.

A completely new method for easy and quick formation of a thin polymer film at the special setting of a stratified oil/water interface. Morphological SEM and quantitative full-field characterization have been reported using digital holography.

Fabrication of chitosan-aminopropylsilane graphene oxide nanocomposite hydrogel embedded PES membrane for improved filtration performance and lead separation

In the present study chitosan-aminopropylsilane graphene oxide (CS-APSGO) nanocomposite hydrogel was synthesized and utilized as a hydrophilic additive in different dosages (0.5, 1, 2 and 5 wt%) in fabrication of porous polyethersulfone (PES) membranes via the phase inversion induced process by immersion precipitation method for heavy metal ion and dye removal. The modified membranes were characterized using ATR-FTIR, AFM, SEM, water contact angle, overall porosity and mean pore radius evaluations and zeta potential measurement. The addition of CS-APSGO nanocomposite hydrogel to PES doping solutions enhanced membranes hydrophilicity and consequently pure water flux permeability. Filtration performance of the CS-APSGO embedded membranes showed promising antifouling properties during BSA filtration test (FRR> 90%) and 1 wt% membranes showed the highest pure water flux of 123.8 L/m² h with BSA rejection more than 98% and removal capability more than 82% for lead (II) ion, 90.5% and 98.5% for C.I. Reactive Blue 50 and C.I. Reactive Green 19, respectively. Therefore, the CS-APSGO nanocomposite hydrogel blending in order to modification of PES-based membranes have a noticeable potential in improving filtration performance of blended membranes.

A Review on Polymer Nanocomposites and Their Effective Applications in Membranes and Adsorbents for Water Treatment and Gas Separation

Globally, environmental challenges have been recognised as a matter of concern. Among these challenges are the reduced availability and quality of drinking water, and greenhouse gases that give rise to change in climate by entrapping heat, which result in respirational illness from smog and air pollution. Globally, the rate of demand for the use of freshwater has outgrown the rate of population increase; as the rapid growth in town and cities place a huge pressure on neighbouring water resources. Besides, the rapid growth in anthropogenic activities, such as the generation of energy and its conveyance, release carbon dioxide and other greenhouse gases, warming the planet. Polymer nanocomposite has played a significant role in finding solutions to current environmental problems. It has found interest due to its high potential for the reduction of gas emission, and elimination of pollutants, heavy metals, dyes, and oil in wastewater. The revolution of integrating developed novel nanomaterials such as nanoparticles, carbon nanotubes, nanofibers and activated carbon, in polymers, have instigated revitalizing and favourable inventive nanotechnologies for the treatment of wastewater and gas separation. This review discusses the effective employment of polymer nanocomposites for environmental utilizations. Polymer nanocomposite membranes for wastewater treatment and gas separation were reviewed together with their mechanisms. The use of polymer nanocomposites as an adsorbent for toxic metals ions removal and an adsorbent for dye removal were also discussed, together with the mechanism of the adsorption process. Patents in the utilization of innovative polymeric nanocomposite membranes for environmental utilizations were discussed.

Phase Inversion-Based Technique for Fabricating Bijels and Bijels-Derived Structures with Tunable Microstructures

Bicontinuous interfacially jammed emulsion gels ("bijels") are a new class of soft matter containing two interpenetrating continuous phases. They have great potential for applications in many areas. However, difficulties in fabricating bijels and controlling structural features of interest have posed severe barriers to their wide applications. In this study, a phase inversion-based technique was developed for fabricating bijels and bijels-derived structures. The effects of varying the composition of casting solutions for the fabrication of bijels on the porosity, oil-to-water percentage, and domain size of bijels were investigated. Composite bijels prepared from two organic monomers were also made, demonstrating the flexibility of the phase inversion-based technique for the fabrication of bijels. Interestingly, the incorporation of a second monomer into the casting solution also affected the porosity and domain size of bijels formed, which may provide a new strategy for the controlled fabrication of bijels. Doxorubicin hydrochloride (DOX, as a model drug)-loaded bijels-derived hybrid hydrogels comprising two continuous phases were successfully made, with one phase being cross-linked alginate that carried the drug. Controlled release of DOX from the bijels-derived structures could be achieved. In vitro degradation study indicated that cross-linking of alginate in bijels-derived hybrid hydrogels controlled alginate degradation, thereby affecting the DOX release behavior. Our current work has provided a facile and reproducible protocol for the controlled fabrication of bijels and bijels-derived structures, which facilitates expanding their applications in the biomedical field.

Catalytic degradation of micropollutant by peroxymonosulfate activation through Fe(III)/Fe(II) cycle confined in the nanoscale interlayer of Fe(III)-saturated montmorillonite

Low cost, green, regenerable catalyst for persulfate activation is the popularly concerned topic for the degradation of persistent organic micropollutants in drinking water. In this work, natural montmorillonite (MMT) saturated with Fe(III) ions was used to activate peroxymonosulfate (PMS) for the degradation of atrazine in raw drinking water. Results showed that the adsorption of atrazine was quickly completed within 1 min and the percentage degradation was finally increased up to 94.1% in 60 min. The d₀₀₁-spacing of MMT was enlarged to 2.91 nm at the most by Fe(III) saturation. Atrazine was adsorbed into the nanoscale interlayer of Fe(III)-saturated montmorillonite (Fe-MMT), where the Fe(III)/Fe(II) cycle was sustainably realized through the accelerated transformation of electrons between Fe(III) and PMS. Meanwhile, the in-situ generated Fe(II) accelerated the decomposition of PMS to further proceed the degradation of atrazine through the oxidation of HO• and SO₄•^- radicals. This nanoconfined effect of PMS activation by Fe(III) was further confirmed through the degradation of various micropollutants in the backgrounds of river water. The selective catalytic oxidation of micropollutants through PMS activation was attributed to the 2D mesoporous structure of Fe-MMT, inhibiting the interlayer adsorption of larger molecular backgrounds (humic acids etc.). Fe(III)-saturated montmorillonite (Fe-MMT) provided a feasible and scalable method of PMS activation by Fe(III) for the degradation of micropollutants in drinking water.

Enhanced permeability and fouling-resistant capacity of poly(vinylidene fluoride) ultrafiltration membrane based on the PPG-co-PEG-co-PPG copolymer with two hydrophobic terminals and one hydrophilic intermediate

A simple and efficient route was used to prepare an amphiphilic copolymer (poly(propylene glycol)-co-poly(ethylene glycol)-co-poly(propylene glycol)) (PPG-co-PEG-co-PPG) by one-pot polymerization reaction. This copolymer was used as the hydrophilic additive in preparation of poly(vinylidene fluoride) (PVDF) ultrafiltration membranes via immersion-precipitation process. Surface characteristics of the membranes were confirmed by contact angle measurements, zeta potential, attenuated total reflectance Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy and atomic force microscopy. During filtration experiments, the modified membranes showed better permeation and antifouling performances compared to PVDF membranes with bovine serum albumin, sodium alginate and yeast. After hydraulic stirring cleaning with deionized water, water flux recovery and rejection ratio of the modified membranes were higher than those of pristine PVDF membrane, and the flux recovery ratio was maximized at 94.29%. It was suggested that PPG-co-PEG-co-PPG copolymer was anchored in the PVDF membrane through the two hydrophobic ends of PPG blocks, while the hydrophilic intermediate of the PEG block segregated onto the membrane or pore surface during the membrane preparation process. The synthesized method of amphiphilic PPG-co-PEG-co-PPG copolymer paved a novel way to solve the problems of less compatibility between the copolymer and membrane matrix and instability with water molecules in the ultrafiltration process.

Recent Advances in Nanoporous Membranes for Water Purification

Nanoporous materials exhibit wide applications in the fields of electrocatalysis, nanodevice fabrication, energy, and environmental science, as well as analytical science. In this review, we present a summary of recent studies on nanoporous membranes for water purification application. The types and fabrication strategies of various nanoporous membranes are first introduced, and then the fabricated nanoporous membranes for removing various water pollutants, such as salt, metallic ions, anions, nanoparticles, organic chemicals, and biological substrates, are demonstrated and discussed. This work will be valuable for readers to understand the design and fabrication of various nanoporous membranes, and their potential purification mechanisms towards different water pollutants. In addition, it will be helpful for developing new nanoporous materials for quick, economic, and high-performance water purification.

Hot-pressed polymer nanofiber supported graphene membrane for high-performance nanofiltration

Graphene oxide (GO) sheets can be readily surface-overlaid on hot-pressed electrospun polyacrylonitrile (PAN) nanofiber membrane to form a continuous and crack-free layer; upon thermal reduction at 150 °C for 12 h, the resulting reduced GO (rGO) layer can reject ∼90% MgSO₄ with high water flux (due to the size exclusion mechanism), making the prepared PAN-rGO membranes promising nanofiltration media for water purification. It is important to note that no delamination of GO/rGO sheet layers has been observed throughout this study. We highlight that a simple processing method (i.e., hot pressing) is critical for the successful preparation of 2D materials (e.g., GO/rGO) based membranes/media. It is envisioned that the reported study can benefit many groups working on various membrane applications of 2D materials; in other words, the hot-pressed electrospun nanofiber membranes could be generally utilized as an innovative type of platform to support various 2D sheets for different separation applications such as highly efficient and cost-effective removal of dissolved components (e.g., organic molecules) and even (hydrated) ions from water.

Efficiency of Polymeric Membrane Graphene Oxide-TiO2for Removal of Azo Dye

Achieving the desired standard of drinking water quality has been one of the concerns across water treatment plants in the developing countries. Processes such as grid chamber, coagulation, sedimentation, clarification, filtration, and disinfection are typically used in water purification plants. Among these methods, unit filtration which employs polymers is one of the new technologies. There have been many studies about the use of semiconductive TiO2with graphene oxide (GO) on the base of different polymeric membranes for the removal of azo dyes, especially methylene blue (MB). Polymeric GO-TiO2membranes have high photocatalytic, antifouling property and permeate the flux removal of organic pollutants. The aim of this study was to investigate the characteristics of different polymeric membranes such as anionic perfluorinated polymer (Nafion), cellulose acetate, polycarbonate (PC), polysulfone fluoride (PSF), and polyvinylidene fluoride (PVDF). The result of this study showed that the GO-TiO2membrane can be used in the field of water treatment and will be used for the removal of polycyclic aromatic hydrocarbons (PAHs) from wastewater.

A review of polymeric membranes and processes for potable water reuse

Conventional water resources in many regions are insufficient to meet the water needs of growing populations, thus reuse is gaining acceptance as a method of water supply augmentation. Recent advancements in membrane technology have allowed for the reclamation of municipal wastewater for the production of drinking water, i.e., potable reuse. Although public perception can be a challenge, potable reuse is often the least energy-intensive method of providing additional drinking water to water stressed regions. A variety of membranes have been developed that can remove water contaminants ranging from particles and pathogens to dissolved organic compounds and salts. Typically, potable reuse treatment plants use polymeric membranes for microfiltration or ultrafiltration in conjunction with reverse osmosis and, in some cases, nanofiltration. Membrane properties, including pore size, wettability, surface charge, roughness, thermal resistance, chemical stability, permeability, thickness and mechanical strength, vary between membranes and applications. Advancements in membrane technology including new membrane materials, coatings, and manufacturing methods, as well as emerging membrane processes such as membrane bioreactors, electrodialysis, and forward osmosis have been developed to improve selectivity, energy consumption, fouling resistance, and/or capital cost. The purpose of this review is to provide a comprehensive summary of the role of polymeric membranes in the treatment of wastewater to potable water quality and highlight recent advancements in separation processes. Beyond membranes themselves, this review covers the background and history of potable reuse, and commonly used potable reuse process chains, pretreatment steps, and advanced oxidation processes. Key trends in membrane technology include novel configurations, materials and fouling prevention techniques. Challenges still facing membrane-based potable reuse applications, including chemical and biological contaminant removal, membrane fouling, and public perception, are highlighted as areas in need of further research and development.

Enhanced sequestration of large-sized dissolved organic micropollutants in polymeric membranes incorporated with mesoporous carbon

Hybrid polyvinylidene fluoride membrane incorporated with mesoporous carbon is fabricated for an enhanced sequestration of large-molecular-sized microcystin-LR and Rhodamine B (3.8 and 14.8 mg g⁻¹, respectively).

Functionalization of polyacrylonitrile with tetrazole groups for ultrafiltration membranes

A series of tetrazole-functionalized polyacrylonitrile (TZ-PAN) copolymers were synthesized via a post-modification cycloaddition reaction of nitriles with azide for ultrafiltration (UF) membrane application.

Recent developments and directions in printed nanomaterials

In this review, we survey several recent developments in printing of nanomaterials for contacts, transistors, sensors of various kinds, light-emitting diodes, solar cells, memory devices, and bone and organ implants. The commonly used nanomaterials are classified according to whether they are conductive, semiconducting/insulating or biological in nature. While many printing processes are covered, special attention is paid to inkjet printing and roll-to-roll printing in light of their complexity and popularity. In conclusion, we present our view of the future development of this field.

Polymeric nanoporous materials fabricated with supercritical CO2 and CO2-expanded liquids

This tutorial review focuses on the recent progress in nanoporous polymeric materials fabricated by newly developed supercritical techniques.