Charge Recombination via Intercolumnar Electron Tunneling through the Lipid-like Mantle of Discotic Hexa-alkyl-hexa-peri-hexabenzocoronenes

Toward Conductive Additive Free Organic Electrode for Lithium-Ion Battery Using Supramolecular Columnar Organization

With the aim to meet the greatest challenge facing organic batteries, namely the low conductivity of the electrodes, the electrochemical properties of a series of substituted perylene diimides able to form semi-conductive columnar material are investigated. Depending on the substituent group, a strong influence of this group on the reversibility, redox potential but especially on the gravimetric capacity of the electrodes is observed. In the case of substitution by a simple propyl group, the corresponding diimide shows a complete electrochemical activity with only 10% by mass of conductive additive and even shows a half-capacity activity without any additive and without particular electrode engineering. Extensive research has highlighted the intrinsic reactivity of the columnar material but also its perpetual rearrangement during charge/discharge cycles. This study shows that the amount of conductive additive can be significantly reduced by adapting the design of the molecular material and favoring the assembly of redox units in the form of a conductive column.

Alkylated Benzodithienoquinolizinium Salts as Possible Non-Fullerene Organic N-Type Semiconductors: An Experimental and Theoretical Study

Three photobicyclized benzodithienoquinolizinium tetrafluoroborates (BPDTQBF4) were prepared and evaluated by UV-Vis and fluorescence spectral, electrochemical analysis, and by theoretical calculations as possible organic n-type semiconductors. Evaluation and comparison of their LUMO levels, HOMO-LUMO energy gaps as monomeric and π-stacked dimers with those of other materials, suggest their potential as organic n-type semiconductors. Calculations of their relative charge carrier mobilities confirmed this potential for one derivative with a long (C-14) alkyl chain appended to the polycyclic planar π-system.

Hexa-peri-hexabenzocoronene decorated with an allenylidene ruthenium complex - almost a flyswatter

Carbon-rich ruthenium allenylidene complexes bearing either a hexaarylbenzene (HAB) or a hexa-peri-hexabenzocoronene (HBC) substituent were synthesised. This was achieved via the corresponding propargyl alcohols with HAB and HBC substituents, which were accessible via 3 or 4 step reaction cascades. Reaction of the propargyl alcohols HC[triple bond, length as m-dash]C(OH)Ph(HAB) and HC[triple bond, length as m-dash]C(OH)Ph(HBC) with [RuCl(η5-C5H5)(PPh3)2] yielded the complexes [Ru(η5-C5H5)([double bond, length as m-dash]C[double bond, length as m-dash]C[double bond, length as m-dash]C(HAB)(Ph))(PPh3)2]PF6 and [Ru(η5-C5H5)([double bond, length as m-dash]C[double bond, length as m-dash]C[double bond, length as m-dash]C(HBC)(Ph))(PPh3)2]PF6. The latter of which shows interesting π-π-stacking behaviour in the solid state as well as aggregation in solution.

One Dimensional Enhanced Anhydrous Proton Conduction in Well Defined Molecular Columns Induced by Non-Covalent Interactions

1D anhydrous proton conduction is enhanced significantly in ionic channels created by self-assembly of functionalized organic phosphonic acid and aromatic heterocyclic 1,2,4-triazole molecules. This study reveals high proton conduction in one dimension through a well-defined supramolecular architecture in which two different molecules undergo host-guest synergy and self-assemble to provide two-fold advantages: 1) formation of the ionic channels and 2) higher proton conduction in the absence of water. A clear correlation is found between the phenomena of ionic channels and anhydrous conductivity in the absolute dry state and we demonstrate that the one-dimensional conductivity can be as high as that recorded for 3D channels in, for instance, Nafion.

Tetrakis(oxadiazolylphenyl)pyrazines: New St. Andrew's Cross-Shaped Liquid Crystals

π-Conjugated molecules with the shape of St. Andrew's cross have been synthesized via fourfold Huisgen reaction. Four 2,5-diaryl-1,3,4-oxadiazol arms are attached to a central pyrazine nucleus. These fluorescent stars, when decorated with a rim of eight alkoxy side chains are discotic liquid crystals. Depending on the substitution pattern, the width of the liquid phase varies within a broad range of 25 °C to 250 °C. In their liquid crystalline phase, the molecules assemble in a typical hexagonal columnar supramolecular arrangement.

Preparation, Electronic and Liquid Crystalline Properties of Electron-Accepting Azaacene Derivatives

A series of electron-accepting azaacene-type materials 1-4 with different kinds and degrees of intermolecular interactions were synthesized. Simple modification of the terminal substituents significantly modulated the photophysical and electrochemical properties. The degree of weak intermolecular interaction determined the emergence of a liquid crystalline (LC) phase for each compound. Dipole-dipole interaction, π-π interaction, and van der Waals interaction all contributed to stabilize the LC phase of 1 and 2. The introduction of strong hydrogen bonding interaction enabled the formation of a highly ordered LC phase in 4. Charge-transport properties of 1, 2, and 4 were also investigated.

Structurally defined nanographene-containing conjugated polymers for high quality dispersions and optoelectronic applications

A new conjugated polymer with nanographenes shows excellent dispersibility in N-cyclohexyl-2-pyrrolidone and remarkable emission from exfoliated nanographenes.

Thermal Evaporation versus Spin-Coating: Electrical Performance in Columnar Liquid Crystal OLEDs

The electrical responses of a columnar liquid crystal (a diimidodiester derivative of benzo[ghi]perylene) deposited either by spin-coating or by thermal evaporation into a typical OLED device are compared. For the spin-coated film, homeotropic alignment was induced by thermal annealing, which enhanced the charge carrier mobility significantly. For the evaporated films, homeotropic alignment could not be obtained by annealing. However, a degree of rectification higher than 3 orders of magnitude was achieved, even without annealing, with an electrical response similar to the response of the aligned spin-coated film. A trap-limited space-charge-limited current model was used to extract the charge carrier mobility directly from the current-voltage curves. Grazing incidence wide-angle X-ray scattering confirmed the homeotropic alignment of the annealed spin-coated film, whereas the columns are mostly oriented parallel to the surface in the evaporated case. In a field-effect transistor with bottom-gate bottom-contact geometry, the evaporated film exhibited a typical behavior of an n-type transistor. The degree of intermolecular order is thereby strongly dependent on the deposition method where vacuum deposition leads to a higher order. This higher order, however, impedes reorientation by annealing of the evaporated film but leads to improved charge transport between the electrodes even without homeotropic alignment of columnar liquid crystal.

Contrasting Response of Two Dipolar Fluorescence Probes in a Leucine-Based Organogel and Its Implications

The microenvironments of a leucine-based organogel are probed by monitoring the fluorescence behavior of coumarin 153 (C153) and 4-aminophthalimide (AP). The steady-state data reveals distinctly different locations of the two molecules in the gel. Whereas AP resides close to the hydroxyl moieties of the gelator and engages in hydrogen-bonding interactions, C153 is found in bulk-toluene-like regions. In contrast to C153, AP exhibits excitation-wavelength-dependent emission, indicating that the environments of the hydrogen-bonded AP molecules are not all identical. A two-component fluorescence decay of AP in gel, unlike C153, supports this model. A time-resolved fluorescence anisotropy study of the rotational motion of the molecules also reveals the strong association of only AP with the gelator. That AP influences the critical gelation concentration implies its direct involvement in the gel-formation process. The results highlight the importance of guest-gelator interactions in gels containing guest molecules.

Modulation and evaluation of the charge carrier mobility in a polymer alloy of polythiophene and an insulating matrix with an electron accepting molecule

Non-contact measurements with time-resolved microwave conductivity and absorption spectroscopy offer direct access to the charge carrier mobility in conjugated backbones.

High charge carrier mobility and efficient charge separation in highly soluble perylenetetracarboxyl-diimides

In this communication we report on the synthesis and charge mobility of highly soluble perylenebisimid derivatives.

Supramolecular self-assembly and photovoltaic property of soluble fluorogallium phthalocyanine

Fluorogallium tetra-tert-butylphthalocyanine (ttbPcGaF) can self-organize into well-ordered cofacial structures to obtain one-dimensional (1D) supramolecular polymers in the solid state using a solution-coating technique. The ttbPcGaF-based BHJ OSC provided a profoundly improved power conversion efficiency (PCE) of 0.41%.

Liquid-crystalline ordering as a concept in materials science: from semiconductors to stimuli-responsive devices

While the unique optical properties of liquid crystals (LCs) are already well exploited for flat-panel displays, their intrinsic ability to self-organize into ordered mesophases, which are intermediate states between crystal and liquid, gives rise to a broad variety of additional applications. The high degree of molecular order, the possibility for large scale orientation, and the structural motif of the aromatic subunits recommend liquid-crystalline materials as organic semiconductors, which are solvent-processable and can easily be deposited on a substrate. The anisotropy of liquid crystals can further cause a stimuli-responsive macroscopic shape change of cross-linked polymer networks, which act as reversibly contracting artificial muscles. After illustrating the concept of liquid-crystalline order in this Review, emphasis will be placed on synthetic strategies for novel classes of LC materials, and the design and fabrication of active devices.

Syntheses and properties of graphyne fragments: trigonally expanded dehydrobenzo[12]annulenes

We present herein the synthesis and properties of the largest hitherto unknown graphyne fragment, namely trigonally expanded tetrakis(dehydrobenzo[12]annulene)s (tetrakis-DBAs). Intramolecular three-fold alkyne metathesis reactions of hexakis(arylethynyl)DBAs 9 a and 9 b using Fürstner's Mo catalyst furnished tetrakis-DBAs 8 a and 8 b substituted with tert-butyl or branched alkyl ester groups in moderate and fair yields, respectively, demonstrating that the metathesis reaction of this protocol is a powerful tool for the construction of graphyne fragment backbones. For comparison, hexakis(arylethynyl)DBAs 9 c-g have also been prepared. The one-photon absorption spectrum of tetrakis-DBA 8 a bearing tert-butyl groups revealed a remarkable bathochromic shift of the absorption cut-off (λcutoff ) compared with those of previously reported graphyne fragments due to extended π-conjugation. Moreover, in the two-photon absorption spectrum, 8 a showed a large cross-section for a pure hydrocarbon because of the planar para-phenylene-ethynylene conjugation pathways. Hexakis(arylethynyl)-DBAs 9 c-e and 9 g and tetrakis-DBA 8 b bearing electron-withdrawing groups aggregated in chloroform solutions. Comparison between the free energies of 9 e and 8 b bearing the same substituents revealed the more favorable association of the latter due to stronger π-π interactions between the extended π-cores. Polarized optical microscopy observations, DSC, and XRD measurements showed that 8 b and 9 e with branched alkyl ester groups displayed columnar rectangular mesophases. By the time-resolved microwave conductivity method, the columnar rectangular phase of 8 b was shown to exhibit a moderate charge-carrier mobility of 0.12 cm(2)  V(-1)  s(-1) . These results indicate that large graphyne fragments can serve as good organic semiconductors.

Comprehensive approach to intrinsic charge carrier mobility in conjugated organic molecules, macromolecules, and supramolecular architectures

Si-based inorganic electronics have long dominated the semiconductor industry. However, in recent years conjugated polymers have attracted increasing attention because such systems are flexible and offer the potential for low-cost, large-area production via roll-to-roll processing. The state-of-the-art organic conjugated molecular crystals can exhibit charge carrier mobilities (μ) that nearly match or even exceed that of amorphous silicon (1-10 cm(2) V(-1) s(-1)). The mean free path of the charge carriers estimated from these mobilities corresponds to the typical intersite (intermolecular) hopping distances in conjugated organic materials, which strongly suggests that the conduction model for the electronic band structure only applies to μ > 1 cm(2) V(-1) s(-1) for the translational motion of the charge carriers. However, to analyze the transport mechanism in organic electronics, researchers conventionally use a disorder formalism, where μ is usually less than 1 cm(2) V(-1) s(-1) and dominated by impurities, disorders, or defects that disturb the long-range translational motion. In this Account, we discuss the relationship between the alternating-current and direct-current mobilities of charge carriers, using time-resolved microwave conductivity (TRMC) and other techniques including field-effect transistor, time-of-flight, and space-charge limited current. TRMC measures the nanometer-scale mobility of charge carriers under an oscillating microwave electric field with no contact between the semiconductors and the metals. This separation allows us to evaluate the intrinsic charge carrier mobility with minimal trapping effects. We review a wide variety of organic electronics in terms of their charge carrier mobilities, and we describe recent studies of macromolecules, molecular crystals, and supramolecular architecture. For example, a rigid poly(phenylene-co-ethynylene) included in permethylated cyclodextrin shows a high intramolecular hole mobility of 0.5 cm(2) V(-1) s(-1), based on a combination of flash-photolysis TRMC and transient absorption spectroscopy (TAS) measurements. Single-crystal rubrene showed an ambipolarity with anisotropic charge carrier transport along each crystal axis on the nanometer scale. Finally, we describe the charge carrier mobility of a self-assembled nanotube consisting of a large π-plane of hexabenzocoronene (HBC) partially appended with an electron acceptor. The local (intratubular) charge carrier mobility reached 3 cm(2) V(-1) s(-1) for the nanotubes that possessed well-ordered π-stacking, but it dropped to 0.7 cm(2) V(-1) s(-1) in regions that contained greater amounts of the electron acceptor because those molecules reduced the structural integrity of π-stacked HBC arrays. Interestingly, the long-range (intertubular) charge carrier mobility was on the order of 10(-4) cm(2) V(-1) s(-1) and monotonically decreased when the acceptor content was increased. These results suggest the importance of investigating charge carrier mobilities by frequency-dependent charge carrier motion for the development of more efficient organic electronic devices.

Hexa-peri-hexabenzocoronene in organic electronics

Polycyclic aromatic hydrocarbons (PAHs) are in a class of functional organic compounds with increasing importance in organic electronics. Their tunable photophysical properties and typically strong intermolecular associations make them ideal materials in applications where control of charge mobility is essential. Hexa-peri-hexabenzocoronene (HBC) is a disc-shaped PAH that self-associates into columnar stacks through strong π–π interactions. By decorating the periphery of the HBC molecule with various substituents, a range of properties and functions can be obtained including solution processability, liquid crystallinity, and semiconductivity. In this review article, the synthesis, properties, and functions of HBC derivatives are presented with focus on work published in the last five years.

Melt processing of hexa-peri-hexabenzocoronene on the water surface

A discotic polycyclic aromatic hydrocarbon, hexa-peri-hexabenzocoronene, was oriented by slow cooling from the isotropic phase on a water surface as a film. For melt processing at low temperatures, an HBC derivative with long swallow-tailed alkyl side chains was chosen. The supramolecular organization in the resulting thin layer was investigated by electron microscopy. In high-resolution mode, the structural study showed large domains in which the columnar structures were oriented uniaxially with an edge-on arrangement of the hydrophobic molecules. The length of the stacks exceeded several hundred nanometers without obvious defects. The small-area analysis by TEM allowed the direct visualization of individual packed molecules. Electron diffraction revealed a high in-plane order of the columnar superstructures in which the discs were tilted by ca. 40° with respect to the stacking direction. This is the first example of a discotic system melt processed on the water surface yielding a pronounced order.

Insulated molecular wire with highly conductive pi-conjugated polymer core

We have recently developed a new method for synthesizing polyrotaxanes with a high covering ratio, rigidity, photoluminescence efficiency, and solubility in a variety of organic solvents through the polymerization of structurally defined rotaxane monomers. The rigid rodlike structure of the pi-conjugated core polymers in these polyrotaxanes is thought to facilitate the effective transport of charge carriers. Here we applied this method to the synthesis of a polyrotaxane having a poly(phenylene ethynylene) backbone by the Sonogashira copolymerization of a structurally defined rotaxane with a linker molecule. According to time-resolved microwave conductivity and transient absorption spectroscopy measurements, the hole mobility along the pi-conjugated polymer chain of the polyrotaxane thus formed was extremely high and comparable to that in amorphous silicon.

Synthesis of poly(para-phenylene)(2-isocyano-2-tosylpropane-1,3-diyl), poly(para-phenylene)(2-oxopropane-1,3-diyl) and oligo(cyclopentadienones) via carbonylative coupling of alpha,alpha'-dibromoxylene

Poly(para-phenylene)(2-oxopropane-1,3-diyl), a potential precursor of linear graphene, is generated in low yield from hydrolysis of a previously unknown poly(para-phenylene)(2-isocyano-2-tosylpropane-1,3-diyl) generated from inexpensive, commercially available starting materials.

Discotic liquid crystals: from tailor-made synthesis to plastic electronics

Most associate liquid crystals with their everyday use in laptop computers, mobile phones, digital cameras, and other electronic devices. However, in contrast to their rodlike (calamitic) counterparts, first described in 1907 by Vorländer, disklike (discotic, columnar) liquid crystals, which were discovered in 1977 by Chandrasekhar et al., offer further applications as a result of their orientation in the columnar mesophase, making them ideal candidates for molecular wires in various optical and electronic devices such as photocopiers, laser printers, photovoltaic cells, light-emitting diodes, field-effect transistors, and holographic data storage. Beginning with an overview of the various mesophases and characterization methods, this Review will focus on the major classes of columnar mesogens rather than presenting a library of columnar liquid crystals. Emphasis will be given to efficient synthetic procedures, and relevant mesomorphic and physical properties. Finally, some applications and perspectives in materials science and molecular electronics will be discussed.

Discotic liquid crystals: a new generation of organic semiconductors

Discotic (disc-like) molecules typically comprising a rigid aromatic core and flexible peripheral chains have been attracting growing interest because of their fundamental importance as model systems for the study of charge and energy transport and due to the possibilities of their application in organic electronic devices. This critical review covers various aspects of recent research on discotic liquid crystals, in particular, molecular design concepts, supramolecular structure, processing into ordered thin films and fabrication of electronic devices. The chemical structure of the conjugated core of discotic molecules governs, to a large extent, their intramolecular electronic properties. Variation of the peripheral flexible chains and of the aromatic core is decisive for the tuning of self-assembly in solution and in bulk. Supramolecular organization of discotic molecules can be effectively controlled by the choice of the processing methods. In particular, approaches to obtain suitable macroscopic orientations of columnar superstructures on surfaces, that is, planar uniaxial or homeotropic alignment, are discussed together with appropriate processing techniques. Finally, an overview of charge transport in discotic materials and their application in optoelectronic devices is given.

Enforced one-dimensional photoconductivity in core-cladding hexabenzocoronenes

Photoconductivity in contorted hexabenzocoronene liquid crystals is found to be exclusively one-dimensional. Spectroscopic measurements and density functional theory support the existence of two pi-systems attributed to a low-energy radialene-core and higher energy out-of-plane alkoxyphenyl rings. Persistent photocurrents, measured as a function of field, channel length, and intensity, fit a stretched exponential characteristic of intracolumnar transport, restricted through the radialene-core by the alkoxyphenyl-cladding. Bimolecular recombination is enhanced with increasing carrier concentration by the system's one-dimensionality.

From Macro- to Nanoscopic Templating with Nanographenes

A hexa-peri-hexabenzocoronene carrying six long, branched alkyl chains has been processed in nano- and macroscopic pore templates. An extraordinary self-organization of this material was observed within macroscopically large glass capillaries after cooling from the isotropic phase. Thereby, the columnar structures were long-range aligned along the capillary axis over several centimeters. This behavior was explained by the pronounced directional self-assembly of the molecules, whereby the curvature effect of the capillary was negligible. The processing in nanoscopic pores of an inorganic membrane yielded an improved supramolecular organization. It was possible to remove the inorganic template and to obtain bundles and single nanorods. The templating over different dimensions opens a variety of potential applications.