CO Oxidation Mechanism on CeO2-Supported Au Nanoparticles

Low Temperature NO and CO Conversion with a Mechanistic Approach on Ru-Composed Cerium Oxide

Catalytic reduction of NO with CO at a lower temperature is an extremely challenging task, thus requiring conceivable surfaces to overcome such issues. Ru-substituted CeO2 catalysts prepared via the solution combustion method were employed in CO oxidation and NO-CO conversion studies. The characterization for material formation and surface structure was carried out through XRD, SEM, TEM, and BET surface area. The catalytic study revealed the promising behavior of 5% Ru in CeO2 for the 100% conversion of NO-CO at 150 °C, proving it to be an excellent exhaust material. These observed results are also supported by temperature-programmed studies, i.e. TPD of NO and CO in addition to NH3-TPD and H2-TPR for their convincible surface interaction that is inclined toward a significant change in the conversion path. Additionally, the proposed mechanism, based on the experimental evidence, sheds light on the NO-CO redox reaction, directing the reaction pathway toward the Langmuir-Hinshelwood and Mars-Van Krevelen-type route. Moreover, the exceptional performance can be attributed to the strategic incorporation of Ru in CeO2, where the strong interaction of Ru-Ce is able to gain a high synergy for NO and CO conversion.

Unraveling distinct effects between CuOx and PtCu alloy sites in Pt-Cu bimetallic catalysts for CO oxidation at different temperatures

In situ exploration of the dynamic structure evolution of catalysts plays a key role in revealing reaction mechanisms and designing efficient catalysts. In this work, PtCu/MgO catalysts, synthesized via the co-impregnation method, outperforms monometallic Pt/MgO and Cu/MgO. Utilizing quasi/in-situ characterization techniques, it is discovered that there is an obvious structural evolution over PtCu/MgO from PtxCuyOz oxide cluster to PtCu alloy with surface CuOx species under different redox and CO oxidation reaction conditions. The synergistic effect between PtCu alloy and CuOx species enables good CO oxidation activity through the regulation of CO adsorption and O2 dissociation. At low temperatures, CO oxidation is predominantly catalyzed by surface CuOx species via the Mars-van Krevelen mechanism, in which CuOx can provide abundant active oxygen species. As the reaction temperature increases, both surface CuOx species and PtCu alloy collaborate to activate gaseous oxygen, facilitating CO oxidation mainly through the Langmuir-Hinshelwood mechanism.

FeOx-Modified Ultrafine Platinum Particles Supported on MgFe2O4 with High Catalytic Activity and Promising Stability toward Low-Temperature Oxidation of CO

Catalytic oxidation is widely recognized as a highly effective approach for eliminating highly toxic CO. The current challenge lies in designing catalysts that possess exceptional low-temperature activity and stability. In this work, we have prepared ultrafine platinum particles of ~1 nm diameter dispersed on a MgFe2O4 support and found that the addition of 3 wt.% FeOx into the 3Pt/MgFe2O4 significantly improves its activity and stability. At an ultra-low temperature of 30 °C, the CO can be totally converted to CO2 over 3FeOx-3Pt/MgFe2O4. High and stable performances of CO-catalytic oxidation can be obtained at 60 °C on 3FeOx-3Pt/MgFe2O4 over 35 min on-stream at WHSV = 30,000 mL/(g·h). Based on a series of characterizations including BET, XRD, ICP, STEM, H2-TPR, XPS, CO-DRIFT, O2-TPD and CO-TPD, it was disclosed that the relatively high activity and stability of 3FeOx-3Pt/MgFe2O4 is due to the fact that the addition of FeOx could facilitate the antioxidant capacity of Pt and oxygen mobility and increase the proportion of adsorbed oxygen species and the amounts of adsorbed CO. These results are helpful in designing Pt-based catalysts exhibiting higher activity and stability at low temperatures for the catalytic oxidation of CO.

Boosting the catalytic performance of Al2O3-supported Pd catalysts by introducing CeO2 promoters

Maintaining the stability of noble metals is the key to the long-term stability of supported catalysts. In response to the instability of noble metal species at high temperatures, we developed a synergistic strategy of dual oxide supports. By designing and constructing ceria components with small sizes, we have achieved unity in the ability of catalytic materials to supply oxygen and stabilize metal species. In this study, we prepared Al2O3-CeO2-Pd (AlCePd) catalysts containing trace amounts of Ce through the hydrolysis of cerium acetate, which achieved 100% CO conversion at 160 °C. More importantly, the activity remained at its initial 100% in the long-term durability testing, demonstrating the high stability of AlCePd. In contrast, the CO conversion of the CeO2-Pd (CePd) catalyst decreased from 100% to 54% within 3 h. Through comprehensive studies, we found that this excellent catalytic performance stems from the stabilizing effect of an alumina support and the possible reverse oxygen spillover effect of small-sized ceria components, where small-sized ceria components provide active oxygen for independent Pd species, making it possible for the CO adsorbed on Pd to react with this oxygen species.

CeO2 nanorods supported CuOx-RuOx bimetallic catalysts for low temperature CO oxidation

Bimetallic catalysts often outperform monometallic catalysts due to changeable structural orientation, synergistic effects, and integration of two different metal or metal oxide properties. Here, a series of CeO2 nanorods (NR) supported bimetallic CuOx and RuOx catalysts (Cu: Ru ratios of 9:1, 7:3, and 5:5) were prepared using a wet impregnation method. In situ DRIFTS, H2 temperature programmed reduction (H2-TPR), CO temperature programmed desorption (CO-TPD), and other characterization techniques were used to investigate the effect of the Cu:Ru ratio on the activity of low-temperature CO oxidation. Among three catalysts, CeO2 NR supported 7 wt% Cu-3 wt% Ru catalyst after a reduction activation treatment showed the best performance with 100 % CO conversion at 166 °C and the lowest activation energy of 18.37 kJ mol-1. Raman and XPS profiles revealed that the origin of the superior performance is at least partially related to the high surface oxygen vacancy concentration and other distinct oxygen species (physi-/chemi-sorbed oxygen and bulk lattice oxygen), leading to outstanding adsorption and oxidation property of CO.

Catalysts Prepared from Atomically Dispersed Ce(III) on MgO Rival Bulk Ceria for CO Oxidation

Atomically dispersed cerium catalysts on an inert, crystalline MgO powder support were prepared by using both Ce(III) and Ce(IV) precursors. The materials were used as catalysts for CO oxidation in a once-through flow reactor and characterized by atomic-resolution scanning transmission electron microscopy, X-ray absorption near-edge structure spectroscopy, X-ray photoelectron spectroscopy, and temperature-programmed reduction, among other techniques, before and after catalysis. The most active catalysts, formed from the precursor incorporating Ce(III), displayed performance similar to that reported for bulk ceria under comparable conditions. The catalyst provided stable time-on-stream performance for as long as it was kept on-stream, 2 days, increasing slightly in activity as the atomically dispersed cerium ions were transformed into ceria nanodomains represented as CeOx and having increased reducibility on the MgO support. The results suggest how highly dispersed supported ceria catalysts with low cerium loadings can be prepared and may pave the way for improved efficiencies of cerium utilization in oxidation catalysis.

Carbon Monoxide Oxidation on Ceria-Supported Nanoclusters

Periodic density functional theory is used to evaluate the minimum energy pathways of CO oxidation on cerium oxide-supported platinum and palladium nanoclusters (Pt/CeO2 and Pd/CeO2). For Pt/CeO2, the oxidation process involves the participation of lattice oxygen from CeO2 at the boundary sites of the cluster-ceria interface, which exhibits an exceptionally low energy barrier. Conversely, on Pd/CeO2, oxidation predominantly occurs through oxygen species bound to the Pd cluster. Experimental analysis using the temperature-programmed reduction of the oxidized Pd/CeO2 catalyst reveals a lower CO oxidation temperature compared to Pt/CeO2. This observation aligns with the anticipated decrease in the energy barrier for CO oxidation due to the oxygen coverage of the Pd cluster.

Atomic-scale insights into the interfacial charge transfer in a NiO/CeO2 heterostructure for electrocatalytic hydrogen evolution

To understand the underlying mechanism of the interfacial charge transfer and local chemical state variation in the nonprecious-based hydrogen evolution reaction (HER) electrocatalysts, a model system of the NiO/CeO₂ heterostructure was chosen for investigation using a combination of the advanced electron microscopic characterization and first-principles calculations. The results directly proved that interfacial charge transfer occurs from Ni to Ce, leading to reduction in the valence state of Ce and increased formation of V_O. This would optimize ΔG_H* and facilitate the hydrogen evolution process, resulting in outstanding HER performance in 1 M KOH with a low overpotential of 99 mV at the current density of 10 mA•cm^-2 and a modest Tafel slope of 78.4 mV•dec^-1 for the NiO/CeO₂ heterostructure sample. Therefore, the improved HER performance could be attributed to the synergistic coupling interactions and electron redistribution at the interface of NiO and CeO₂. These results concretely demonstrate the direct determination of the interfacial structure of the heterostructure and provide atomistic insights to unravel the underlying mechanism of interfacial charge transfer induced HER performance improvement.

Iterative multiscale and multi-physics computations for operando catalyst nanostructure elucidation and kinetic modeling

Modern heterogeneous catalysis has benefitted immensely from computational predictions of catalyst structure and its evolution under reaction conditions, first-principles mechanistic investigations, and detailed kinetic modeling, which are rungs on a multiscale workflow. Establishing connections across these rungs and integration with experiments have been challenging. Here, operando catalyst structure prediction techniques using density functional theory simulations and ab initio thermodynamics calculations, molecular dynamics, and machine learning techniques are presented. Surface structure characterization by computational spectroscopic and machine learning techniques is then discussed. Hierarchical approaches in kinetic parameter estimation involving semi-empirical, data-driven, and first-principles calculations and detailed kinetic modeling via mean-field microkinetic modeling and kinetic Monte Carlo simulations are discussed along with methods and the need for uncertainty quantification. With these as the background, this article proposes a bottom-up hierarchical and closed loop modeling framework incorporating consistency checks and iterative refinements at each level and across levels.

Fabrication of supported Pt/CeO2 nanocatalysts doped with different elements for CO oxidation: theoretical and experimental studies

Supported Pt/CeO₂ catalysts have been widely used in carbon monoxide (CO) oxidation; however, the high oxygen vacancy formation energy (E_vac) in the process leads to the poor performance of these catalysts. Herein, we explored different element (Pr, Cu, or N) doped CeO₂ supports using Ce-based metal-organic frameworks (MOFs) as precursors via calcination treatment. The obtained CeO₂ supports were used to load Pt nanoparticles. These catalysts were systematically characterized by various techniques, and they showed superior catalytic activity for CO oxidation compared to undoped catalysts which could be attributed to the formation of Ce³⁺, and high amounts of O_ads/(O_ads + O_lat) and Pt^δ+/Pt_total. Moreover, density functional theory calculations with on-site Coulomb interaction correction (DFT+U) were performed to provide atomic-scale insights into the reaction process by the Mars-van Krevelen (M-vK) mechanism, which revealed that the element-doped catalysts could simultaneously reduce the adsorption energies of CO and lower reaction energy barriers in the *OOCO associative pathway.

Distinct morphology-dependent behaviors for Au/γ-Al2O3 catalysts: enhanced thermal stabilization in CO oxidation reaction

The durability of supported metal catalysts usually suffers from sintering, the metal nanoparticles aggregating into larger sizes and subsequent loss of reactive surface, resulting in catalysts deactivation when heated at elevated temperatures. Herein, we investigate the evolution of Au species on different morphologies of γ-Al2O3 and surprisingly found vastly different behavior for the dispersion of surface Au nanoparticles. A nanorod-shaped γ-Al2O3 is prepared by the hydrothermal method resulting in an extraordinary catalyst support that can stabilize Au nanoparticles at annealing temperatures up to 700 °C. In contrast, the Au-supported catalyst prepared using commercial γ-Al2O3 shows a greater degree of inactivation under the same conditions. Remarkably, the unique morphology of such nanorod-shaped γ-Al2O3 is beneficial in preventing Au nanoparticles from sintering. The γ-Al2O3 nanorods are more effective than the commercial γ-Al2O3 at anchoring the Au nanoparticles. The results of X-ray photoelectron spectroscopy (XPS), in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) and H2-TPR, reveal the interfacial interactions between Au nanoparticles and γ-Al2O3 nanorods, yielding a sinter-stability of the obtained Au/γ-Al2O3 nanorods catalyst. This synthetic strategy is simple and amenable to the large-scale manufacture of thermally stable γ-Al2O3 for industrial applications. Here, we investigate the morphology-dependent behavior of Au nanoparticles dispersed on different morphologies of γ-Al2O3. The result of X-ray photoelectron spectroscopy (XPS), in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) and H2-TPR, reveal the interfacial interactions between Au nanoparticles and gamma alumina nanorods. Au nanoparticles on γ-Al2O3 nanorods exhibit higher sinter-resistant performance than those on commercial γ-Al2O3.

In situ synthesis of Cu nanoclusters/CeO2 nanorod as aggregated induced ECL probe for triple-negative breast cancer detection

Cu nanoclusters (NCs) have attracted a lot of attention due to the excellent properties. However, the low luminescence and poor stability limited the Cu NC-based sensing research. In this work, Cu NCs were in situ synthesized on CeO₂ nanorods. On the one hand, the aggregated induced electrochemiluminescence (AIECL) of Cu NCs has been observed on the CeO₂ nanorods. On the other hand, the substrate of CeO₂ nanorods acted as catalysis, which reduced the excitation potential and further enhanced the ECL signal of Cu NCs. It was noticed that CeO₂ nanorods also greatly improved the stability of Cu NCs. The resulted high ECL signals of Cu NCs can be kept constant for several days. Furthermore, MXene nanosheets/Au NPs has been employed as electrode modification materials to construct the sensing platform to detect miRNA-585-3p in triple negative breast cancer tissues. Au NPs@MXene nanosheets not only enlarged the specific interface area of the electrodes and the number of reaction sites, but also modulated electron transfer to amplify the ECL signal of Cu NCs. The biosensor had a low detection limit (0.9 fM) and a wide linear range (1 fM to 1 μM) for the detection of miRNA-585-3p in the clinic tissues.

In situ diffraction monitoring of nanocrystals structure evolving during catalytic reaction at their surface

With decreasing size of crystals the number of their surface atoms becomes comparable to the number of bulk atoms and their powder diffraction pattern becomes sensitive to a changing surface structure. On the example of nanocrystalline gold supported on also nanocrystalline [Formula: see text] we show evolution of (a) the background pattern due to chemisorption phenomena, (b) peak positions due to adsorption on nonstoichiometric [Formula: see text] particles, (c) Au peaks intensity. The results of the measurements, complemented with mass spectrometry gas analysis, point to (1) a multiply twinned structure of gold, (2) high mobility of Au atoms enabling transport phenomena of Au atoms to the surface of ceria while varying the amount of Au in the crystalline form, and (3) reversible [Formula: see text] peaks position shifts on exposure to He-X-He where X is O₂, H₂, CO or CO oxidation reaction mixture, suggesting solely internal alternations of the [Formula: see text] crystal structure. We found no evidence of ceria lattice oxygen being consumed/supplied at any stage of the process. The work shows possibility of structurally interpreting different contributions to the multi-phase powder diffraction pattern during a complex physico-chemical process, including effects of physi-, chemisorption and surface evolution. It shows a way to structurally interpret heterogeneous catalytic reactions even if no bulk phase transition is involved.

Atomically Incorporating Ni into Mesoporous CeO2 Matrix via Synchronous Spray-Pyrolysis as Efficient Noble-Metal-Free Catalyst for Low-Temperature CO Oxidation

Low-temperature catalytic CO oxidation is an important chemical process in versatile applications, such as the H₂ utilization for low-temperature H₂ air fuel cells. Pt-group metal catalysts are efficient but highly cost-consuming. This work demonstrates an excellent and sixpenny catalyst with earth-abundant Ni and Ce, in which Ni ions are atomically incorporated into the CeO₂ matrix (Ni-Ce-O_x) by synchronous spray-pyrolysis (SSP) of mixture nitrates of Ni and Ce. The Ni-Ce-O_x catalyst presents a mesoporous structure. Revealed by a model reaction of 1% CO, 1% O₂, and 98% balance He at a space velocity of 13,200 mL/g_cat/h, Ni-Ce-O_x catalysts display a typical volcano-shaped relationship between reactivity and Ni incorporation amount. The optimized Ni incorporation appears with a high Ni/Ce atomic ratio of 0.25, endowing the T₅₀ (temperature corresponding to a CO conversion of 50%), which is lower-shifted by 165 °C than that of pristine CeO₂ (266 °C). The density functional theory (DFT) calculations further indicate that the much-reduced oxygen vacancy formation energy at Ni-Ce single-atom sites boosted the adsorption activation of the CO molecule and therefore promoted the CO oxidation process. Besides, the₂ Ni-Ce-O_x from the SSP method presents better performance than the counterparts from immersion and hydrothermal methods. This work paves a way to access efficient noble-metal-free catalysts for low-temperature CO oxidation.

In Situ Spectroscopy and Microscopy Insights into the CO Oxidation Mechanism on Au/CeO2(111)

In this work, we prepared and investigated in ultra-high vacuum (UHV) two stoichiometric CeO₂(111) surfaces containing low and high amounts of step edges decorated with 0.05 ML of gold using synchrotron-radiation photoelectron spectroscopy (SRPES) and scanning tunneling microscopy (STM). The UHV study helped to solve the still unresolved puzzle on how the one-monolayer-high ceria step edges affect the metal-substrate interaction between Au and the CeO₂(111) surface. It was found that the concentration of ionic Au⁺ species on the ceria surface increases with increasing number of ceria step edges and is not correlated with the concentration of Ce³⁺ ions that are supposed to form on the surface after its interaction with gold nanoparticles. We associated this with an additional channel of Au⁺ formation on the surface of CeO₂(111) related to the interaction of Au atoms with various peroxo oxygen species formed at the ceria step edges during the film growth. The study of CO oxidation on the highly stepped Au/CeO₂(111) model sample was performed by combining near-ambient-pressure X-ray photoelectron spectroscopy (NAP-XPS), UHV-STM, and near-ambient-pressure STM (NAP-STM). This powerful combination provided comprehensive information on the processes occurring on the Au/CeO₂(111) surface during the interaction with CO, O₂, and CO + O₂ (1:1) mixture at conditions close to the real working conditions of CO oxidation. It was found that the system demonstrates high stability in CO. However, the surface undergoes substantial chemical and morphological changes as the O₂ is added to the reaction cell. Already at 300 K, gold nanoparticles begin to grow using a mechanism that involves the disintegration of small gold nanoparticles in favor of the large ones. With increasing temperature, the model catalyst quickly transforms into a system of primarily large Au particles that contains no ionic gold species.

Controlling the Size of Au Nanoparticles on Reducible Oxides with the Electrochemical Potential

Controlling the size of Au nanoparticles (NPs) and their interaction with the oxide support is important for their catalytic performance in chemical reactions, such as CO oxidation and water-gas shift. It is known that the oxygen vacancies at the surface of support oxides form strong chemical bonding with the Au NPs and inhibit their coarsening and deactivation. The resulting Au/oxygen vacancy interface also acts as an active site for oxidation reactions. Hence, small Au NPs are needed to increase the density of the Au/oxide interface. A dynamic way to control the size of the Au NPs on an oxide support is desirable but has been missing in the field. Here, we demonstrate an electrochemical method to control the size of the Au NPs by controlling the surface oxygen vacancy concentration of the support oxide. Oxides with different reducibilities, La_0.8Ca_0.2MnO_3±δ and Pr_0.1Ce_0.9O_2-δ, are used as model support oxides. By applying the electrochemical potential, we achieve a wide range of effective oxygen pressures, pO₂ (10^-37-10¹⁴ atm), in the support oxides. Applying the cathodic potential creates a high concentration of oxygen vacancies and forms finely distributed Au NPs with sizes of 7-13 nm at 700-770 °C in 10 min, while the anodic potential oxidizes the surface and increases the size of the Au NPs. The onset cathodic potential required to create small Au NPs depends strongly on the reducibility of the support oxide. The Au NPs did not undergo sintering even at 700-770 °C under the cathodic potential and also were stable in catalytically relevant conditions without potential.

Combining surface chemical functionalization with introducing reactive oxygen species boosts ethanol electrooxidation

The introduction of functional groups or oxygen vacancies into Pd-based electrocatalysts is a powerful strategy for enhancing the electrocatalytic performances for many electrocatalytic reactions. Herein, an amorphous ceria-modified Pd nanocomposite anchored on D-4-amino-phenylalanine (DAP)-functionalized graphene nanosheets (Pd-CeO_2-x/FGS) was prepared by a facile and effective one-pot synthetic strategy and further used as an electrocatalyst for the ethanol oxidation reaction (EOR) in alkaline electrolytes. The obtained Pd-CeO_2-x/FGS exhibits relatively high electrocatalytic activity, fast kinetics and excellent antipoisoning ability as well as robust durability for EOR, outperforming the comparable electrocatalysts as well as commercial Pd/C. The experimental results show that the enhanced EOR properties of Pd-CeO_2-x/FGS can be attributed to the DAP-functionalization and CeO_2-x-modification. Adequate functional groups (amino and carboxyl groups) and abundant oxygen vacancies were introduced in Pd-CeO_2-x/FGS by DAP-functionalization and CeO_2-x-modification. The functional groups facilitate the anchoring of small nanoparticles onto the substrate as well as modulate the electron density of Pd. The oxygen vacancies boost the adsorption ability of the reactive oxygen species (OH_ads) and accelerate the kinetics of the potential-limiting step for EOR. This study proposes a new strategy for the rational design of highly efficient catalysts for the electro-oxidation reaction.

Gold single-atoms confined at the CeOx-TiO2interfaces with enhanced low-temperature activity toward CO oxidation

We use CeO_x-TiO₂hetero-interfaces generated on the surface of CeO_x-TiO₂hybrid oxide supporting powders to stabilize Au single-atoms (SAs) with excellent low-temperature activity toward CO oxidation. Based on intriguing density functional theory calculation results on the preferential formation of Au-SAs at the CeO_x-TiO₂interfaces and the high activity of Au-SAs toward the Mars-van Krevelen type CO oxidation, we synthesized a Au/CeO_x-TiO₂(ACT) catalyst with 0.05 wt.% of Au content. The Au-SAs stabilized at the CeO_x-TiO₂interfaces by electronic coupling between Au and Ce showed improved low-temperature CO oxidation activity than the conventional Au/TiO₂control group catalyst. However, the light-off profile of ACT showed that the early activated Au-SAs are not vigorously participating in CO oxidation. The large portion of the positive effect on the overall catalytic activity from the low activation energy barrier of ACT was retarded by the negative impact from the decreasing active site density at high temperatures. We anticipate that the low-temperature activity and high-temperature stability of Au-SAs that stand against each other can be optimized by controlling the electronic coupling strength between Au-SAs and oxide clusters at the Au-oxide-TiO₂interfaces. Our results show that atomic-precision interface modulation could fine-tune the catalytic activity and stability of Au-SAs.

Mechanistic and thermodynamic insights into the SO2 oxidation on MnO2 catalysts: A combined theoretical and experimental study

Manganese oxide (especially manganese dioxide [MnO₂]) is an excellent catalytic material for SO₂ removal in flue gas desulfurization. In this study, the effect of crystalline structure of MnO₂ (α-MnO₂, β-MnO₂, γ-MnO₂ and δ-MnO₂) on their activity for SO₂ oxidation was studied based on density functional theory with Hubbard U corrections (DFT + U). The calculated results showed that α-MnO₂ has mild energy barriers of 0.69 eV and 0.46 eV, and β-MnO₂ has poor redox performance on SO₂ molecules, which has the highest energy barrier of 2.17 eV and the largest oxygen formation energy of 1.74 eV, making it difficult for the oxygen atom to remove from the surface lattice to form reactive sites. Thermodynamic calculations showed that α-MnO₂ is suitable for SO₂ oxidation for its low energy barriers, reaction energy close to zero in the first half, and relatively high spontaneity in the whole reaction. Experimental tests showed that α-MnO₂ had the best catalytic oxidation effect, with the highest sulfur capacity (304.11 mg/g), but β-MnO₂ had poor catalytic oxidation performance, with a sulfur capacity of 41.59 mg/g. This work studies the catalytic performance and mechanism of SO₂ removal and proposes a strategy to improve the catalytic activity by phase structure.

X-ray Photoelectron Spectroscopy (XPS) Analysis of Ultrafine Au Nanoparticles Supported over Reactively Sputtered TiO2 Films

The impact of a titania (TiO₂) support film surface on the catalytic activity of gold nanoparticles (Au NP) was investigated. Using the reactive dc-magnetron sputtering technique, TiO₂ films with an amorphous, anatase, and nitrogen-doped anatase crystal structure were produced for a subsequent role as a support material for Au NP. Raman spectra of these TiO₂ films revealed that both vacuum and NH₃ annealing treatments promoted amorphous to anatase phase transformation through the presence of a peak in the 513-519 cm^-1 spectral regime. Furthermore, annealing under NH₃ flux had an associated blue shift and broadening of the Raman active mode at 1430 cm^-1, characteristic of an increase in the oxygen vacancies (V_O). For a 3 to 15 s sputter deposition time, the Au NP over TiO₂ support films were in the 6.7-17.1 nm size range. From X-ray photoelectron spectroscope (XPS) analysis, the absence of any shift in the Au 4f core level peak implied that there was no change in the electronic properties of Au NP. On the other hand, spontaneous hydroxyl (-OH) group adsorption to anatase TiO₂ support was instantly detected, the magnitude of which was found to be enhanced upon increasing the Au NP loading. Nitrogen-doped anatase TiO₂ supporting Au NP with ~21.8 nm exhibited a greater extent of molecular oxygen adsorption. The adsorption of both -OH and O₂ species is believed to take place at the perimeter sites of the Au NP interfacing with the TiO₂ film. XPS analyses and discussions about the tentative roles of O₂ and -OH adsorbent species toward Au/TiO₂ systems corroborate very well with interpretations of density functional theory simulations.

Tuning the coordination environment of Fe atoms enables 3D porous Fe/N-doped carbons as bifunctional electrocatalyst for rechargeable zinc-air battery

As one of the most promising candidates for power sources, the rechargeable Zn-air batteries have attracted much attention due to their high energy density. However, Zn-air batteries suffer from sluggish kinetics of oxygen reduction (ORR) and oxygen evolution reaction (OER) during the discharge and charge process. Herein, a FeN₂-doped carbon with a unique three-dimensional (3D) porous structure (CeO₂-FeNC-5) was synthesized as an electrocatalyst for Zn-air batteries by one-step pyrolysis and introducing CeO₂ to tune the coordination environment of Fe atoms. Extended X-ray absorption fine structure (EXAFS) results indicate that the introduction of CeO₂ can convert FeN₃ moieties into FeN₂ moieties. The CeO₂-FeNC-5 exhibits a more positive half-wave potential of 0.902 V for ORR, and a low overpotential of 0.327 V at 10 mA cm^-2 for OER. Furthermore, the Zn-air battery with CeO₂-FeNC-5 achieve a maximum power density (169 mW cm^-2), a high open voltage platform (1.47 V) and superior cycling stability (200 h). The unique 3D porous structure provides channels for mass transport and exposes sufficient active sites to facilitate the ORR and OER processes. Calculations prove that FeN₂ moieties are beneficial to O₂ adsorption on Fe/N-doped carbon surface. This work provides an effective strategy for designing and synthesizing FeN_x-doped carbon matrix electrocatalysts for sustainable metal-air batteries.

Metal-Support Interaction and Charge Distribution in Ceria-Supported Au Particles Exposed to CO

Understanding how reaction conditions affect metal-support interactions in catalytic materials is one of the most challenging tasks in heterogeneous catalysis research. Metal nanoparticles and their supports often undergo changes in structure and oxidation state when exposed to reactants, hindering a straightforward understanding of the structure-activity relations using only ex situ or ultrahigh vacuum techniques. Overcoming these limitations, we explored the metal-support interaction between gold nanoparticles and ceria supports in ultrahigh vacuum and after exposure to CO. A combination of in situ methods (on powder and model Au/CeO₂ samples) and theoretical calculations was applied to investigate the gold/ceria interface and its reactivity toward CO exposure. X-ray photoelectron spectroscopy measurements rationalized by first-principles calculations reveal a distinctly inhomogeneous charge distribution, with Au⁺ atoms in contact with the ceria substrate and neutral Au⁰ atoms at the surface of the Au nanoparticles. Exposure to CO partially reduces the ceria substrate, leading to electron transfer to the supported Au nanoparticles. Transferred electrons can delocalize among the neutral Au atoms of the particle or contribute to forming inert Au^δ- atoms near oxygen vacancies at the ceria surface. This charge redistribution is consistent with the evolution of the vibrational frequencies of CO adsorbed on Au particles obtained using diffuse reflectance infrared Fourier transform spectroscopy.

Recent applications of nanoparticles in organic transformations

A variation in the size of metal nanoparticles leads to a difference in their properties. As the size of metal nanoparticles decreases, the surface area increases which leads to an increase in the reactivity of metal nanoparticles. Metals like Au, Ag, Pd, and Pt have interesting properties when used in nanometric dimensions. They function efficiently in significant industrial processes as electrocatalysts and photocatalysts in various organic reactions. Recently, the green biosynthesis of nanoparticles has attracted the attention of researchers. With environmental pollution rising over the past few decades, metal nanoparticle catalysts could be the key to subdue the toxic effects. Being versatile, they can be used to degrade pollutants, develop solar cells, convert toxic nitroaromatic compounds, significantly reduce CO₂ emissions per unit of energy, and many more. Owing to their unique properties, nanoparticles have wide applications in biomedicine, for example, gold cages are promising agents for cancer diagnosis and therapy. Transition metal-oxide nanoparticles have been considered one of the best supercapacitor electrodes with high electrochemical performance. In this review, we have summarised fundamental concepts of metal nanoparticles over the last decade's main emphasis from 2010 to 2021. It focuses on the exceptional use of these nanocatalysts in various organic reactions. Additionally, we have also discussed the utility of these reactions and their crucial role in solving the problems of today. Through this article, we hope to provide the necessary framework needed to further advance the applications of metal nanoparticles as catalysts.

Light-to-Hydrogen Improvement Based on Three-Factored Au@CeO2/Gr Hierarchical Photocatalysts

Recently, various attempts have been made for light-to-fuels conversion, often with limited performance. Herein we report active and lasting three-factored hierarchical photocatalysts consisting of plasmon Au, ceria semiconductor, and graphene conductor for hydrogen production. The Au@CeO₂/Gr_2.0 entity (graphene outer shell thickness of 2.0 nm) under visible-light irradiation exhibits a colossal achievement (8.0 μmol mg_cat^-1 h^-1), which is 2.2- and 14.3-fold higher than those of binary Au@CeO₂ and free-standing CeO₂ species, outperforming the currently available catalysts. Yet, it delivers a high maximum quantum yield efficiency of 38.4% at an incident wavelength of 560 nm. These improvements are unambiguously attributed to three indispensable effects: (1) the plasmon resonant energy is light-excited and transferred to produce hot electrons localizing near the surface of Au@CeO₂, where (2) the high-surface-area Gr conductive shell will capture them to direct hydrogen evolution reactions, and (3) the active graphene hybridized on the defect-rich surface of Au@CeO₂ favorably adsorbs hydrogen atoms, which all bring up thorough insight into the working of a ternary Au@CeO₂/Gr catalyst system in terms of light-to-hydrogen conversion.

Effects of chemical etching and reduction activation of CeO2 nanorods supported ruthenium catalysts on CO oxidation

In this work, pristine and NaBH₄ etched CeO₂ nanorods supported ruthenium (Ru) catalysts were synthesized and employed to investigate the effects of chemical etching and reduction activation treatment on CO oxidation. With 1 wt% Ru loading, the CeO₂ nanorods supported catalyst samples, after 6 wt% NaBH₄ etching treatment, showed significantly promoted H₂ consumption under 100 °C and low apparent activation energy (i.e., E_a ∼ 31.2 kJ/mol) for CO oxidation. In-situ CO-DRIFTS profiles revealed that, for the reduced sample, the observed CO adsorption at ∼ 2020 cm^-1 at 40 °C may be related to a strong RuO_x-CeO₂ interaction induced by the NaBH₄ etching treatment, which was supported by the oxygen vacancy analysis results of X-ray photoelectron spectroscopy and CO-temperature programmed desorption. The enriched surface defects on CeO₂ support due to the chemical etching and reduction treatments are believed to promote the interaction between RuO_x species and CeO₂, which is responsible for the enhanced activity of CO oxidation.

Modeling surface spin polarization on ceria-supported Pt nanoparticles

In this work, we employ density functional theory simulations to investigate possible spin polarization of CeO₂-(111) surface and its impact on the interactions between a ceria support and Pt nanoparticles. With a Gaussian type orbital basis, our simulations suggest that the CeO₂-(111) surface exhibits a robust surface spin polarization due to the internal charge transfer between atomic Ce and O layers. In turn, it can lower the surface oxygen vacancy formation energy and enhance the oxide reducibility. We show that the inclusion of spin polarization can significantly reduce the major activation barrier in the proposed reaction pathway of CO oxidation on ceria-supported Pt nanoparticles. For metal-support interactions, surface spin polarization enhances the bonding between Pt nanoparticles and ceria surface oxygen, while CO adsorption on Pt nanoparticles weakens the interfacial interaction regardless of spin polarization. However, the stable surface spin polarization can only be found in the simulations based on the Gaussian type orbital basis. Given the potential importance in the design of future high-performance catalysts, our present study suggests a pressing need to examine the surface ferromagnetism of transition metal oxides in both experiment and theory.

C-H Bond Activation Mechanism by a Pd(II)-(μ-O)-Au(0) Structure Unique to Heterogeneous Catalysts

We focused on identifying a catalytic active site structure at the atomic level and elucidating the mechanism at the elementary reaction level of liquid-phase organic reactions with a heterogeneous catalyst. In this study, we experimentally and computationally investigated efficient C-H bond activation for the selective aerobic α,β-dehydrogenation of saturated ketones by using a Pd-Au bimetallic nanoparticle catalyst supported on CeO₂ (Pd/Au/CeO₂) as a case study. Detailed characterization of the catalyst with various observation methods revealed that bimetallic nanoparticles formed on the CeO₂ support with an average size of about 2.5 nm and comprised a Au nanoparticle core and PdO nanospecies dispersed on the core. The formation mechanism of the nanoparticles was clarified through using several CeO₂-supported controlled catalysts. Activity tests and detailed characterizations demonstrated that the dehydrogenation activity increased with the coordination numbers of Pd-O species in the presence of Au(0) species. Such experimental evidence suggests that a Pd(II)-(μ-O)-Au(0) structure is the true active site for this reaction. Based on density functional theory calculations using a suitable Pd₁O₂Au₁₂ cluster model with the Pd(II)-(μ-O)-Au(0) structure, we propose a C-H bond activation mechanism via concerted catalysis in which the Pd atom acts as a Lewis acid and the adjacent μ-oxo species acts as a Brønsted base simultaneously. The calculated results reproduced the experimental results for the selective formation of 2-cyclohexen-1-one from cyclohexanone without forming phenol, the regioselectivity of the reaction, the turnover-limiting step, and the activation energy.

Interspersing CeOx Clusters to the Pt-TiO2 Interfaces for Catalytic Promotion of TiO2-Supported Pt Nanoparticles

We propose an interface-engineered oxide-supported Pt nanoparticle-based catalyst with improved low-temperature activity toward CO oxidation. By wet-impregnating 1 wt % Ce on TiO₂, we synthesized hybrid oxide support of CeO_x-TiO₂, in which dense CeO_x clusters formed on the surface of TiO₂. Then, the Pt/CeO_x-TiO₂ catalyst was synthesized by impregnating 2 wt % Pt on the CeO_x-TiO₂ supporting oxide. Pt-CeO_x-TiO₂ triphase interfaces were eventually formed upon impregnation of Pt on CeO_x-TiO₂. The Pt-CeO_x-TiO₂ interfaces open up the interface-mediated Mars-van Krevelen CO oxidation pathway, thus providing additional interfacial reaction sites for CO oxidation. Consequently, the specific reaction rate of Pt/CeO_x-TiO₂ for CO oxidation was increased by 3.2 times compared with that of Pt/TiO₂ at 140 °C. Our results demonstrate a widely applicable and straightforward method of catalytic activation of the interfaces between metal nanoparticles and supporting oxides, which enabled fine-tuning of the catalytic performance of oxide-supported metal nanoparticle classes of heterogeneous catalysts.

The lanthanide doping effect on toluene catalytic oxidation over Pt/CeO2 catalyst

The present work was undertaken to know the lanthanide doping effect on the physicochemical properties of Pt/CeO₂ catalysts and their catalytic activity for toluene oxidation. A series of lanthanide ions (La, Pr, Nd, Sm and Gd) were incorporated into ceria lattice by hydrothermal method, and the Pt nanoparticles with equal quality were successfully loaded on various ceria-based supports. Their catalytic performance toward toluene oxidation shows a remarkable lanthanide-doping effect, and the activity is much dependent on the ion radius and valence state of dopants. Owing to smaller ion radius and low valence state, the dopant of Gd would form more Gd-Ce complex and less GdO₈-type complex, generating more oxygen vacancies and then promoting oxygen replenishment. Furthermore, the high concentration of oxygen vacancy would drive electrons to transfer from support to metal, and thus electron-rich and under-coordinated Pt particles that are favorable for toluene adsorption and dissociation are obtained. Attributing to above positive factors, the doping of Gd would effectively enhance the catalytic oxidation of toluene over Pt/CeO₂ catalyst. In addition, the Pt/CeGdO₂ sample exhibits an excellent reaction stability and resistance of concentration impact.

Fabrication of MnCoOx composite oxides for catalytic CO oxidation via a solid-phase synthesis: The significant effect of manganese precursor

A series of Mn3Co16Ox composite oxides catalysts were fabricated via a solid-phase synthesis using different manganese precursors (namely as manganese acetate (A), nitrate (N), and sulfate (S)). It has been...

Probing the role of surface activated oxygen species of CeO2 nanocatalyst during the redox cycle in CO oxidation

The oxygen species of CeO₂ nanocatalysts plays a key role in the CO oxidation. In this work, nanocrystalline CeO₂ with infrared spectroscopy detectable surface superoxide (O₂⁻) species at room temperature is fabricated and CO oxidation is used as a probe reaction for the exploration of the characteristics of surface O₂⁻ species on the CeO₂ surface. We discover that the surface O₂⁻ species have ignorable influences on the overall reaction rate of CO oxidation on pure ceria by comparing P-CeO₂ (CeO₂ prepared by precipitation method) with HT-CeO₂ (CeO₂ prepared by hydrothermal method). It is concluded that the reaction between CO molecules and surface O₂⁻ species is the first and the fast step in the whole redox cycle, while the release of surface lattice oxygen is the second and the rate determining step of the catalysts. This work gives an intuitionistic exploration on the redox properties of pure nanocrystalline CeO₂ with surface O₂⁻ species and reveals the influences of these species in the whole redox circle of CO oxidation.

Pure CeO₂ nanocatalysts fabricated by different methods are obtained and the impact of surface oxygen species on their CO oxidation is compared and evaluated.

The dynamic interplay between water and oxygen vacancy at the near-surface of ceria

Water, even at trace concentrations, strongly increases the CO oxidation activities of the reducible metal oxide supported noble-metal catalysts, where the transfer of proton plays a key role. In this paper, we performed a thorough investigation of the interplay between water molecules and the reduced CeO₂(111) surface. It was found that water molecules can induce the migration of oxygen vacancies which in turn results in the formation of surface protons. The proton then entangles with the near-surface polaron to form polaron-proton pair due to their mutual attractive interactions. The hopping of the polaron can easily trigger the long-range or short-range diffusion of protons mediated by water molecules at the CeO₂(111) surface. These findings provide new insights into the key roles of oxygen vacancies and polarons in reducible oxide based heterogeneous catalysis, which is beneficial for the understanding of the increased activity of reducible oxide supported metal nanoparticles in the presence of water.

Enhanced adsorption and degradation of methylene blue over mixed niobium-cerium oxide - Unraveling the synergy between Nb and Ce in advanced oxidation processes

Formation of reactive oxygen species (ROS) via H₂O₂ activation is of vital importance in catalytic environmental chemistry, especially in degradation of organic pollutants. A new mixed niobium-cerium oxide (NbCeO_x) was tailored for this purpose. A thorough structural and chemical characterization of NbCeO_x along with CeO₂ and Nb₂O₅ reference materials was carried out using TEM/STEM/EDS, SEM, XRD, XPS, EPR, UV-vis and N₂ physisorption. The ability of the catalysts to activate H₂O₂ towards ROS formation was assessed on the basis of EPR and Raman measurements. Catalytic activity of the oxides was evaluated in degradation of methylene blue (MB) as a model pollutant. Very high activity of NbCeO_x was attributed to the mixed redox-acidic nature of its surface, which originated from the synergy between Nb and Ce species. These two properties (redox activity and acidity) ensured convenient conditions for efficient activation of H₂O₂ and degradation of MB. The activity of NbCeO_x in MB degradation was found 3 times higher than that of the commercial Nb₂O₅ CBMM catalyst and 240 times higher than that of CeO₂. The mechanism of the degradation reaction was found to be an adsorption-triggered process initiated by hydroxyl radicals, generated on the surface via the transformation of O₂^-•/O₂^2-.

Recent advances in catalytic systems in the prism of physicochemical properties to remediate toxic CO pollutants: A state-of-the-art review

Carbon monoxide (CO) is the most harmful pollutant in the air, causing environmental issues and adversely affecting humans and the vegetation and then raises global warming indirectly. CO oxidation is one of the most effective methods of reducing CO by converting it into carbon dioxide (CO₂) using a suitable catalytic system, due to its simplicity and great value for pollution control. The CO oxidation reaction has been widely studied in various applications, including proton-exchange membrane fuel cell technology and catalytic converters. CO oxidation has also been of great academic interest over the last few decades as a model reaction. Many review studies have been produced on catalysts development for CO oxidation, emphasizing noble metal catalysts, the configuration of catalysts, process parameter influence, and the deactivation of catalysts. Nevertheless, there is still some gap in a state of the art knowledge devoted exclusively to synergistic interactions between catalytic activity and physicochemical properties. In an effort to fill this gap, this analysis updates and clarifies innovations for various latest developed catalytic CO oxidation systems with contemporary evaluation and the synergistic relationship between oxygen vacancies, strong metal-support interaction, particle size, metal dispersion, chemical composition acidity/basicity, reducibility, porosity, and surface area. This review study is useful for environmentalists, scientists, and experts working on mitigating the harmful effects of CO on both academic and commercial levels in the research and development sectors.

Bimetallic Nanocrystals: Structure, Controllable Synthesis and Applications in Catalysis, Energy and Sensing

In recent years, bimetallic nanocrystals have attracted great interest from many researchers. Bimetallic nanocrystals are expected to exhibit improved physical and chemical properties due to the synergistic effect between the two metals, not just a combination of two monometallic properties. More importantly, the properties of bimetallic nanocrystals are significantly affected by their morphology, structure, and atomic arrangement. Reasonable regulation of these parameters of nanocrystals can effectively control their properties and enhance their practicality in a given application. This review summarizes some recent research progress in the controlled synthesis of shape, composition and structure, as well as some important applications of bimetallic nanocrystals. We first give a brief introduction to the development of bimetals, followed by the architectural diversity of bimetallic nanocrystals. The most commonly used and typical synthesis methods are also summarized, and the possible morphologies under different conditions are also discussed. Finally, we discuss the composition-dependent and shape-dependent properties of bimetals in terms of highlighting applications such as catalysis, energy conversion, gas sensing and bio-detection applications.