Isolated Cobalt Centers on W18O49 Nanowires Perform as a Reaction Switch for Efficient CO2 Photoreduction

Boosting Solar-Driven CO2 Conversion to Ethanol via Single-Atom Catalyst with Defected Low-Coordination Cu-N2 Motif

Cu-based catalysts have been shown to selectively catalyze CO2 photoreduction to C2+ solar fuels. However, they still suffer from poor activity and low selectivity. Herein, we report a high-performance carbon nitride supported Cu single-atom catalyst featuring defected low-coordination Cu-N2 motif (Cu-N2-V). Lead many recently reported photocatalysts and its Cu-N3 and Cu-N4 counterparts, Cu-N2-V exhibits superior photocatalytic activity for CO2 reduction to ethanol and delivers 69.8 μmol g-1 h-1 ethanol production rate, 97.8 % electron-based ethanol selectivity, and a yield of ~10 times higher than Cu-N3 and Cu-N4. Revealed by the extensive experimental investigation combined with DFT calculations, the superior photoactivity of Cu-N2-V stems from its defected Cu-N2 configuration, in which the Cu sites are electron enriched and enhance electron delocalization. Importantly, Cu in Cu-N2-V exist in both Cu+ and Cu2+ valence states, although predominantly as Cu+. The Cu+ sites support the CO2 activation, while the co-existence of Cu+/Cu2+ sites are highly conducive for strong *CO adsorption and subsequent *CO-*CO dimerization enabling C-C coupling. Furthermore, the hollow microstructure of the catalyst also promotes light adsorption and charge separation efficiency. Collectively, these make Cu-N2-V an effective and high-performance catalyst for the solar-driven CO2 conversion to ethanol. This study also elucidates the C-C coupling reaction path via *CO-*CO to *COCOH and rate-determining step, and reveals the valence state change of partial Cu species from Cu+ to Cu2+ in Cu-N2-V during CO2 photoreduction reaction.

Manipulation of Oxidation States on Phase Boundary via Surface Layer Modification for Enhanced Alkaline Hydrogen Electrocatalysis

In alkaline water electrolysis and anion exchange membrane water electrolysis technologies, the hydrogen evolution reaction (HER) at the cathode is significantly constrained by a high energy barrier during the water dissociation step. This study employs a phase engineering strategy to construct heterostructures composed of crystalline Ni4W and amorphous WOx aiming to enhance catalytic performance in the HER under alkaline conditions. This work systematically modulates the oxidation states of W within the amorphous WOx of the heterostructure to adjust the electronic states of the phase boundary, the energy barriers associated with the water dissociation step, and the adsorption/desorption properties of intermediates during the alkaline HER process. The optimized catalyst, Ni4W/WOx-2, with a quasi-metallic state of W coordinated by a low oxygen content in amorphous WOx, demonstrates exceptional catalytic performance (22 mV@10 mA cm-2), outperforming commercial Pt/C (30 mV@10 mA cm-2). Furthermore, the operando X-ray absorption spectroscopy analysis and theoretical calculations reveal that the optimized W atoms in amorphous WOx serve as active sites for water dissociation and the nearby Ni atoms in crystalline Ni4W facilitated the release of H2. These findings provide valuable insights into designing efficient heterostructured materials for energy conversion.

Cascaded *CO-*COH Intermediates on a Nonmetallic Plasmonic Photocatalyst for CO2-to-C2H6 with 90.6 % Selectivity

Oxygen vacancies (OV) in nonmetallic plasmonic photocatalysts can decrease the energy barrier for CO2 reduction, boosting C1 intermediate production for potential C2 formation. However, their susceptibility to oxidation weakens C1 intermediate adsorption. Herein we proposed a "photoelectron injection" strategy to safeguard OV in W18O49 by creating a W18O49/ZIS (W/Z) plasmonic photocatalyst. Moreover, photoelectrons contribute to the local multi-electron environment of W18O49, enhancing the intrinsic excitation of its hot electrons with extended lifetimes, as confirmed by in situ XPS and femtosecond transient absorption analysis. Density functional theory calculations revealed that W/Z with OV enhances CO2 adsorption, activating *CO production, while reducing the energy barrier for *COH production (0.054 eV) and subsequent *CO-*COH coupling (0.574 eV). Successive hydrogenation revealed that the free energy for *CH2CH2 hydrogenation (0.108 eV) was lower than that for *CH2CH2 desorption for C2H4 production (0.277 eV), favouring C2H6 production. Consequently, W/Z achieves an efficient C2H6 activity of 653.6 μmol g-1 h-1 under visible light, with an exceptionally high selectivity of 90.6 %. This work offers a new strategy for the rational design of plasmonic photocatalysts with high selectivity for C2+ products.

Asymmetric Cu(I)─W Dual-Atomic Sites Enable C─C Coupling for Selective Photocatalytic CO2 Reduction to C2H4

Solar-driven CO2 reduction into value-added C2+ chemical fuels, such as C2H4, is promising in meeting the carbon-neutral future, yet the performance is usually hindered by the high energy barrier of the C─C coupling process. Here, an efficient and stabilized Cu(I) single atoms-modified W18O49 nanowires (Cu1/W18O49) photocatalyst with asymmetric Cu─W dual sites is reported for selective photocatalytic CO2 reduction to C2H4. The interconversion between W(V) and W(VI) in W18O49 ensures the stability of Cu(I) during the photocatalytic process. Under light irradiation, the optimal Cu1/W18O49 (3.6-Cu1/W18O49) catalyst exhibits concurrent high activity and selectivity toward C2H4 production, reaching a corresponding yield rate of 4.9 µmol g-1 h-1 and selectivity as high as 72.8%, respectively. Combined in situ spectroscopies and computational calculations reveal that Cu(I) single atoms stabilize the *CO intermediate, and the asymmetric Cu─W dual sites effectively reduce the energy barrier for the C─C coupling of two neighboring CO intermediates, enabling the highly selective C2H4 generation from CO2 photoreduction. This work demonstrates leveraging stabilized atomically-dispersed Cu(I) in asymmetric dual-sites for selective CO2-to-C2H4 conversion and can provide new insight into photocatalytic CO2 reduction to other targeted C2+ products through rational construction of active sites for C─C coupling.

Co single atom coupled oxygen vacancy on W18O49 nanowires surface to construct asymmetric active site enhanced peroxymonosulfate activation

Enhancing the activation of peroxymonosulfate (PMS) is essential for generating more reactive oxygen species in advanced oxidation process (AOPs). Nevertheless, improving PMS adsorption and expediting interfacial electron transfer to enhance reaction kinetics pose significant challenges. Herein, we construct confined W18O49 nanowires with asymmetric active centers containing Co-Vo-W (Vo: oxygen vacancy). The design incorporates surface-rich Vo and single-atom Co, and the resulting material is employed for PMS activation in water purification. By coupling unsaturated coordinated electrons in Vo with low-valence Co single atoms to construct an the "electron fountainhead", the adsorption and activation of PMS are enhanced. This results in the generation of more active free radicals (SO4•-, •OH, •O2-) and non-free radicals (1O2) for the decomposition of micropollutants. Thereinto, the degradation rate of bisphenol A (BPA) by Co-W18O49 is 32.6 times faster that of W18O49 monomer, which is also much higher than those of other transition-metal-doped W18O49 composites. This work is expected to help to elucidate the rational design and efficient PMS activation of catalysts with asymmetric active centers.

Methyl contributes to the directed phosphorus doping of g-C3N4: pH-dependent selective reactive oxygen species enable customized degradation of organic pollutants

In the photocatalytic degradation process, constructing a controllable composite oxidation system with radicals and nonradicals to meet the requirement for efficient and selective degradation of diverse pollutants is significant. Herein, a methylated and phosphorus-doped g-C3N4 (NPEA) can exhibit selective radical and nonradical species formation depending on the pH values. The NPEA can spontaneously switch the production of active species according to the pH value of the reaction system, exhibiting steady-state concentrations of ·O2- for 11.83 × 10-2 µmol L-1 s-1 (with 92.7 % selectivity) under alkaline conditions (pH = 11), and steady-state concentrations of 1O2 for 5.18 × 10-2 µmol L-1 s-1 (with 88.7 % selectivity) under acidic conditions (pH = 3). The NPEA exhibits stability and universality in the degradation of pollutants with rate constant for sulfamethazine (k = 0.261 min-1) and atrazine (k = 0.222 min-1). Moreover, the LC-MS and Fukui function demonstrated that the NPEA can tailor degradation pathways for pollutants, achieving selective degradation. This study offers a comprehensive insight into the mechanism of the photocatalytic oxidation system, elucidating the intricate interplay between pollutants and reactive oxygen species.

Self-powered photoelectrochemical immunosensing platform for sensitive CEA detection using dual-photoelectrode synergistic signal amplification

Self-powered photoelectrochemical (PEC) sensing, as an emerging sensing mode, can effectively solve the problems such as weak anti-interference ability and poor signal response of individual photoanode or photocathode sensing. In this work, an ITO/Co-CuInS2 photocathode and ITO/WO3@CdS photoanode based self-powered cathodic PEC immunosensor was developed, which integrated dual-photoelectrode to synergistic amplify the signal for highly sensitive and specific detection of carcinoembryonic antigen (CEA). The self-powered PEC sensor could drive electrons transfer through the difference in Fermi levels between the two photoelectrodes without an external bias voltage. The photoanode was introduced to amplify the photoelectric signal, and the photocathode was only designed for the construction of sensing interfaces. The proposed sensor quantitatively determined the target CEA with the detection limit of 0.23 pg/mL and a linear correlation confine of 0.1 pg/mL ∼100 ng/mL. The constructed immunosensing platform exhibited high sensitivity, satisfactory stability and great biological detection selectivity, providing a feasible and effective strategy for the manufacture of new self-powered sensors in high-performance PEC bioanalytical applications.

Visible-Light-Driven Inactivation of Bacteria and H2 Generation Catalyzed by Oxygen-Vacancy-Rich One-Dimensional/Two-Dimensional W18O49/g-C3N4 Z-Scheme Heterostructures

Z-scheme heterostructure-based photocatalysts consist of a reduction photocatalyst and an oxidation photocatalyst, enabling them to possess a high capacity for both reduction and oxidation. However, the coupling reaction between photocatalytic H2 generation through water reduction and sterilization using Z-scheme systems has been rarely reported. Herein, 1D W18O49 nanowires embedded over 2D g-C3N4 nanosheets are well-constructed as an integrated Z-scheme heterojunction. Experimental results and density functional theory calculations not only demonstrate the achievement of efficient interfacial charge separation and transport, leading to prolonged lifetime of photogenerated charge carriers, but also directly confirm the mechanism of Z-scheme charge transfer. As expected, the optimized W18O49/g-C3N4 nanostructure exhibits superior photocatalytic sterilization activity against Staphylococcus aureus as well as excellent H2 generation performance under visible-light irradiation (λ ≥ 420 nm). Due to its nontoxic nature, W18O49/g-C3N4 holds great potential in eradicating bacterial infections in living organisms.

Oxygen-Activated Boron Nitride for Selective Photocatalytic Coupling of Methanol to Ethylene Glycol

The controllable photocatalytic C-C coupling of methanol to produce ethylene glycol (EG) is a highly desirable but challenging objective for replacing the current energy-intensive thermocatalytic process. Here, we develop a metal-free porous boron nitride catalyst that demonstrates exceptional selectivity in the photocatalytic production of EG from methanol under mild conditions. Comprehensive experiments and calculations are conducted to thoroughly investigate the reaction mechanism, revealing that the OB3 unit in the porous BN plays a critical role in the preferential activation of C-H bond in methanol to form ⋅CH2OH via a concerted proton-electron transfer mechanism. More prominent energy barriers are observed for the further dehydrogenation of the ⋅CH2OH intermediate on the OB3 unit, inhibiting the formation of some other by-products during the catalytic process. Additionally, a small downhill energy barrier for the coupling of ⋅CH2OH in the OB3 unit promotes the selective generation of EG. This study provides valuable insights into the underlying mechanisms and can serve as a guide for the design and optimization of photocatalysts for efficient and selective EG production under mild conditions.

Optimizing potassium polysulfides for high performance potassium-sulfur batteries

Potassium-sulfur batteries attract tremendous attention as high-energy and low-cost energy storage system, but achieving high utilization and long-term cycling of sulfur remains challenging. Here we show a strategy of optimizing potassium polysulfides for building high-performance potassium-sulfur batteries. We design the composite of tungsten single atom and tungsten carbide possessing potassium polysulfide migration/conversion bi-functionality by theoretical screening. We create two ligand environments for tungsten in the metal-organic framework, which respectively transmute into tungsten single atom and tungsten carbide nanocrystals during pyrolysis. Tungsten carbide provide catalytic sites for potassium polysulfides conversion, while tungsten single atoms facilitate sulfides migration thereby significantly alleviating the insulating sulfides accumulation and the associated catalytic poisoning. Resultantly, highly efficient potassium-sulfur electrochemistry is achieved under high-rate and long-cycling conditions. The batteries deliver 89.8% sulfur utilization (1504 mAh g-1), superior rate capability (1059 mAh g-1 at 1675 mA g-1) and long lifespan of 200 cycles at 25 °C. These advances enlighten direction for future KSBs development.

Schottky Junction and D-A1 -A2 System Dual Regulation of Covalent Triazine Frameworks for Highly Efficient CO2 Photoreduction

Covalent triazine frameworks (CTFs) are emerging as a promising molecular platform for photocatalysis. Nevertheless, the construction of highly effective charge transfer pathways in CTFs for oriented delivery of photoexcited electrons to enhance photocatalytic performance remains highly challenging. Herein, a molecular engineering strategy is presented to achieve highly efficient charge separation and transport in both the lateral and vertical directions for solar-to-formate conversion. Specifically, a large π-delocalized and π-stacked Schottky junction (Ru-Th-CTF/RGO) that synergistically knits a rebuilt extended π-delocalized network of the D-A1 -A2 system (multiple donor or acceptor units, Ru-Th-CTF) with reduced graphene oxide (RGO) is developed. It is verified that the single-site Ru units in Ru-Th-CTF/RGO act as effective secondary electron acceptors in the lateral direction for multistage charge separation/transport. Simultaneously, the π-stacked and covalently bonded graphene is regarded as a hole extraction layer, accelerating the separation/transport of the photogenerated charges in the vertical direction over the Ru-Th-CTF/RGO Schottky junction with full use of photogenerated electrons for the reduction reaction. Thus, the obtained photocatalyst has an excellent CO2 -to-formate conversion rate (≈11050 µmol g-1 h-1 ) and selectivity (≈99%), producing a state-of-the-art catalyst for the heterogeneous conversion of CO2 to formate without an extra photosensitizer.

Study on synergistic effects of 4f levels of erbium and black phosphorus/SnNb2O6 heterostructure catalysts by multiple spectroscopic analysis techniques

Lanthanide single atom modified catalysts are rarely reported because the roles of lanthanide in photocatalysis are difficult to explain clearly. Based on the construction of Er single atom modified black phosphorus/SnNb2O6 (BP/SNO) heterojunctions, the synergistic effect of 4f levels of Er and heterostructures was studied by combining steady-state, transient, and ultrafast spectral analysis techniques with DFT theoretical calculations. According to the Judd-Ofelt theory of lanthanide ions, the CO2 photoreduction test under single wavelength excitation verifies that the 4F7/2/2H11/2 → 4I15/2 emissions of Er in BPEr/SNOEr can be more easily absorbed by SNO and BP, further proving the role of the 4f levels. As a result, the CO and CH4 yields of BPEr/SNOEr-10 under visible light irradiation are 10.7 and 10.1 times higher than those of pure BP, respectively, and 3.4 and 1.5 times higher than those of SNO. The results of DFT calculations show that the Er single atoms can cause surface reconstruction, regulate the active sites of BP, and reduce the energy change value in the key steps (CO2* + H+ + e- → COOH* and COOH* → CO* + H2O). This work provides novel insights into the design of lanthanide single atom photocatalysts for CO2 reduction.

Modulating Charge Separation of Oxygen-Doped Boron Nitride with Isolated Co Atoms for Enhancing CO2 -to-CO Photoreduction

To alleviate the greenhouse effect and address the related energy crisis, solar-driven reduction of carbon dioxide (CO2 ) to value-added products is considered as a sustainable strategy. However, the insufficient separation and rapid recombination of photogenerated charge carriers during photocatalysis greatly limit their reduction efficiency and practical application potential. Here, isolated Cobalt (Co) atoms are successfully decorated into oxygen-doped boron nitride (BN) via an in situ pyrolysis method, achieving greatly improved catalytic activity and selectivity to the carbon monoxide (CO) product. X-ray absorption fine spectroscopy demonstrates that the isolated Co atoms are stabilized by the O and N atoms with an unsaturated CoO2 N1 configuration. Further experimental investigation and theoretical simulations confirm that the decorated Co atoms not only work as the real active center during the CO2 reduction process, but also perform as the electron pump to promote the electron/hole separation and transfer, resulting in greatly accelerated reaction kinetics and improved activity. In addition, the CoO2 N1 coordination geometry is favorable to the conversion from *CO2 to *COOH, which shall be considered as a selectivity-determining step for the evolution of the CO products. The surface modulation strategy at the atomic level opens a new avenue for regulating the reaction kinetics for photocatalytic CO2 reduction.

Photocatalytic Degradation of Gaseous Benzene Using Cu/Fe-Doped TiO2 Nanocatalysts under Visible Light

Visible-light-enhanced TiO2 nanocatalysts doped with Cu and Fe were synthesized using the sol-gel method to investigate their performance in degrading gaseous benzene. The structure and morphology of mono- and co-doped TiO2 (i.e., Cu/Fe-TiO2, Cu-Fe-TiO2) were characterized using SEM, EDS, XRD, BET, Raman, UV-vis-DRS, and XPS techniques. The results indicated that the presence of Cu/Fe mono- and co-doped TiO2 leads to the formation of an anatase phase similar to pure TiO2. Furthermore, the introduction of Cu/Fe enhanced the presence of lattice defects and increased the specific surface area of TiO2. This enhancement can be attributed to the increase in oxygen vacancies, especially in the case of Cu-Fe-TiO2. Additionally, Cu-Fe-TiO2 showed a higher concentration of surface-bound hydroxyl groups/chemically adsorbed oxygen and a narrower bandgap than pure TiO2. Consequently, Cu-Fe-TiO2 exhibited the highest photocatalytic performance of 658.33 μgC6H6/(g·h), achieving a benzene degradation rate of 88.87%, surpassing that of pure TiO2 (5.09%), Cu-TiO2 (66.92%), and Fe-TiO2 (59.99%). Reusability tests demonstrated that Cu-Fe-TiO2 maintained a high benzene degradation efficiency of 71.4%, even after five experimental cycles, highlighting its exceptional stability and reusability. In summary, the addition of Cu/Fe to TiO2 enhances its ability to degrade gaseous benzene by prolonging the catalyst's lifespan and expanding its photoresponse range to include visible light.

Metal-Free Photocatalytic CO2 Reduction to CH4 and H2 O2 under Non-sacrificial Ambient Conditions

Photocatalytic CO2 reduction to CH4 requires photosensitizers and sacrificial agents to provide sufficient electrons and protons through metal-based photocatalysts, and the separation of CH4 from by-product O2 has poor applications. Herein, we successfully synthesize a metal-free photocatalyst of a novel electron-acceptor 4,5,9,10-pyrenetetrone (PT), to our best knowledge, this is the first time that metal-free catalyst achieves non-sacrificial photocatalytic CO2 to CH4 and easily separable H2 O2 . This photocatalyst offers CH4 product of 10.6 μmol ⋅ g-1  ⋅ h-1 under non-sacrificial ambient conditions (room temperature, and only water), which is two orders of magnitude higher than that of the reported metal-free photocatalysts. Comprehensive in situ characterizations and calculations reveal a multi-step reaction mechanism, in which the long-lived oxygen-centered radical in the excited PT provides as a site for CO2 activation, resulting in a stabilized cyclic carbonate intermediate with a lower formation energy. This key intermediate is thermodynamically crucial for the subsequent reduction to CH4 product with the electronic selectivity of up to 90 %. The work provides fresh insights on the economic viability of photocatalytic CO2 reduction to easily separable CH4 in non-sacrificial and metal-free conditions.

Highly stable and durable ZnIn2S4 nanosheets wrapped oxygen deficient blue TiO2(B) catalyst for selective CO2 photoreduction into CO and CH4

Developing new and highly stable efficient photocatalysts is crucial for achieving high performance and selective photocatalytic CO2 conversion. In this paper, we designed a one-dimensional oxygen-deficient blue TiO2(B) (BT) catalyst for improved electron mobility and visible light accessibility. In addition, hexagonal ZnIn2S4 (ZIS) nanosheets with a low bandgap and great visible light accessibility are employed to produce effective heterostructures with BT. The synthesized materials are tested for photocatalytic conversion of CO2 into solar fuels (H2, CO and CH4). The optimized composite yields 71.6 and 10.3 μmol g-1h-1 of CO and CH4, three and ten times greater than ZIS, respectively. When ZIS nanosheets are combined with a one-dimensional oxygen-deficient BT catalyst, improved electron mobility and visible light accessibility are achieved, charge carriers are effectively segregated, and the transfer process is accelerated, resulting in efficient CO2 reduction. The photocatalytic CO2 conversion activity of the constructed BT/ZIS heterostructures is very stable over a 10-day (240-hour) period, and CO and CH4 production rates increase linearly with time; however, as time goes on, the rates of H2 production decrease. Further, a five-time recycling test confirmed this, revealing essentially equal activity and selectivity throughout the experiment. As a result, CO2 to CO and CH4 conversion has high selectivity and longer durability. The band structure of the BT/ZIS composite is determined using Mott-Schottky measurement, diffuse reflectance spectroscopy, and valence band X-ray photoelectron spectroscopy. This research demonstrates a novel approach to investigating effective, stable, and selective photocatalytic CO2 reduction systems for solar-to-chemical energy conversion.

Recent Advances on Single-Atom Catalysts for Photocatalytic CO2 Reduction

The present energy crisis and environmental challenges may be efficiently resolved by converting carbon dioxide (CO2 ) into various useful carbon products. The development of more effective catalysts has been the main focus of current research on photocatalytic CO2 reduction. Due to their high atomic efficiency and superior catalytic activity, single-atom catalysts (SACs) have attracted considerable interest in catalytic CO2 conversion. This review discusses the current research developments, obstacles, and potential of SACs for photocatalytic CO2 reduction. And further, discusses the principle of photocatalytic carbon dioxide reduction. This work has compared and analyzed the effects of support materials and active site types in SACs on photocatalytic CO2 reduction performance. This work believes that by sharing these developments, some inspiration for the rational design and development of stable and effective photocatalytic CO2 reduction catalysts based on SACs can be provided.

Porphyrin Supramolecular Nanoassembly/C3N4 Nanosheet S-Scheme Heterojunctions for Selective Photocatalytic CO2 Reduction toward CO

The photocatalytic reduction of CO2 with H2O into valuable chemicals is a sustainable carbon-neutral technology for renewable energy; however, the photocatalytic activity and product selectivity remain challenging. Herein, an S-scheme heterojunction photocatalyst with superior CO2 photoreduction performance─porous C3N4 (CN) nanosheets anchored with zinc(II) tetra(4-cyanophenyl)porphyrin (ZnTP) nanoassemblies (denoted as ZnTP/CN)─was designed and prepared via a simple self-assembly process. The constructed ZnTP/CN heterojunction had rich accessible active sites, improved CO2 absorption capacity, and high charge carrier separation efficiency caused by the S-scheme heterojunction. As a result, the obtained ZnTP/CN catalyst exhibited considerable activity for photocatalytic CO2 reduction, yielding CO with a generation rate of 19.4 μmol g-1·h-1 and a high selectivity of 95.8%, which is much higher than that of pristine CN nanosheets (4.53 μmol g-1·h-1, 57.4%). In addition, theoretical calculations and in situ Fourier transform infrared spectra demonstrated that the Zn sites in the porphyrin unit favor CO2 activation and *COOH formation as well as CO desorption, thereby affording a high CO selectivity. This work provides insight into the design and fabrication of efficient S-scheme heterostructure photocatalysts for solar energy storage.

DFT Calculation of Carbon-Doped TiO2 Nanocomposites

Titanium dioxide (TiO2) has been proven to be an excellent material for mitigating the continuous impact of elevated carbon dioxide concentrations. Carbon doping has emerged as a promising strategy to enhance the CO2 reduction performance of TiO2. In this study, we investigated the effects of carbon doping on TiO2 using density functional theory (DFT) calculations. Two carbon doping concentrations were considered (4% and 6%), denoted as TiO2-2C and TiO2-3C, respectively. The results showed that after carbon doping, the band gaps of TiO2-2C and TiO2-3C were reduced to 1.58 eV and 1.47 eV, respectively, which is lower than the band gap of pure TiO2 (2.13 eV). This indicates an effective improvement in the electronic structure of TiO2. Barrier energy calculations revealed that compared to pure TiO2 (0.65 eV), TiO2-2C (0.54 eV) and TiO2-3C (0.59 eV) exhibited lower energy barriers, facilitating the transition to *COOH intermediates. These findings provide valuable insights into the electronic structure changes induced by carbon doping in TiO2, which can contribute to the development of sustainable energy and environmental conservation measures to address global climate challenges.

Single-Atom Cu Stabilized on Ultrathin WO2.72 Nanowire for Highly Selective and Ultrasensitive ppb-Level Toluene Detection

Various catalysts are developed to improve the performance of metal oxide semiconductor gas sensors, but achieving high selectivity and response intensity in chemiresistive gas sensors (CGSs) remains a significant challenge. In this study, an in situ-annealing approach to synthesize Cu catalytic sites on ultrathin WO2.72 nanowires for detecting toluene at ultralow concentrations (Ra /Rg = 1.9 at 10 ppb) with high selectivity is developed. Experimental and molecular dynamic studies reveal that the Cu single atoms (SAs) act as active sites, promoting the oxidation of toluene and increasing the affinity of Cu single-atom catalysts (SACs)-containing sensing materials for toluene while weakening the association with carbon dioxide or water vapor. Density functional theory studies show that the selective binding of toluene to Cu SAs is due to the favorable binding sites provided by Cu SAs for toluene molecules over other gaseous species, which aids the adsorption of toluene on WO2.72 nanowires. This study demonstrates the successful atomic-level interface regulation engineering of WO2.72 nanowire-supported Cu SAs, providing a potential strategy for the development of highly active and durable CGSs.

Efficient charge separation and transfer in a one-dimensional carbon nanotube/tungsten oxide p-n heterojunction composite for solar energy conversion

Efficient and cost-effective photocatalysts for solar energy conversion represent a rapidly advancing and compelling area of research. In our study, we employed theoretical calculations to design a novel composite material consisting of a one-dimensional (1D) carbon nanotube (CNT) and tungsten oxide (W18O49) p-n heterojunction. This composite material was successfully synthesized using a straightforward solvothermal method, and we thoroughly investigated the charge separation and transfer mechanism. Our findings revealed that the composite material exhibited a superior photocurrent response. Notably, the CNTs/W18O49-2 sample demonstrated a significantly higher photocurrent under both AM 1.5G and infrared light irradiation, outperforming the individual components under AM 1.5G by a substantial factor of 30. This remarkable enhancement in performance can be attributed to the efficient charge separation and transfer facilitated by the built-in electric field created at the interface through the p-n heterojunction. Our study introduces a pioneering integration of CNTs and 1D tungsten oxide, resulting in a composite structure with a p-n heterojunction-a concept that has not been extensively explored previously. The results confirmed the formation of this unique one-dimensional structure and a p-n heterojunction, which has outstanding properties for various applications. These findings provide a robust foundation for the design of photocatalytic interfaces and offer a fresh approach to the development of high-performance photocatalysts.

Surface Modification of TiO2 by Hyper-Cross-Linked Polymers for Efficient Visible-Light-Driven Photocatalytic NO Oxidation

Solar-driven photocatalysis offers an environmentally friendly and sustainable approach for the removal of air pollutants such as nitric oxides without chemical addition. However, the low specific surface area and adsorption capacity of common photocatalysts restrict the surface reactions with NO at the ppb-level. In this study, imidazolium-based hyper-cross-linked polymer (IHP) was introduced to modify the surface of TiO₂ to construct a porous TiO₂/IHP composite photocatalyst. The as-prepared composite with hierarchical porous structure achieves a larger specific surface area as 309 m²/g than that of TiO₂ (119 m²/g). Meanwhile, the wide light absorption range of the polymer has brought about the strong visible-light absorption of the TiO₂/IHP composite. In consequence, the composite photocatalyst exhibits excellent performance toward NO oxidation at a low concentration of 600 ppb under visible-light irradiation, reaching a removal efficiency of 51.7%, while the generation of the toxic NO₂ intermediate was suppressed to less than 1 ppb. The enhanced NO adsorption and the suppressed NO₂ generation on the TiO₂/IHP surface were confirmed by in situ monitoring technology. This work demonstrates that the construction of a porous structure is an effective approach for efficient NO adsorption and photocatalytic oxidation.

Atomically Strained Metal Sites for Highly Efficient and Selective Photooxidation

Strain engineering is an attractive strategy for improving the intrinsic catalytic performance of heterogeneous catalysts. Manipulating strain on the short-range atomic scale to the local structure of the catalytic sites is still challenging. Herein, we successfully achieved atomic strain modulation on ultrathin layered vanadium oxide nanoribbons by an ingenious intercalation chemistry method. When trace sodium cations were introduced between the V₂O₅ layers (Na⁺-V₂O₅), the V-O bonds were stretched by the atomically strained vanadium sites, redistributing the local charges. The Na⁺-V₂O₅ demonstrated excellent photooxidation performance, which was approximately 12 and 14 times higher than that of pristine V₂O₅ and VO₂, respectively. Complementary spectroscopy analysis and theoretical calculations confirmed that the atomically strained Na⁺-V₂O₅ had a high surficial charge density, improving the activation of oxygen molecules and contributing to the excellent photocatalytic property. This work provides a new approach for the rational design of strain-equipped catalysts for selective photooxidation reactions.

Regulating Activity and Selectivity of Photocatalytic CO2 Reduction on Cobalt by Rare Earth Compounds

Cobalt-based catalysts are ideal for CO₂ reduction reaction (CO₂RR) due to the strong binding and efficient activation of CO₂ molecules on cobalt. However, cobalt-based catalysts also show low free energy of hydrogen evolution reaction (HER), making HER competitive with CO₂RR. Therefore, how to improve the product selectivity of CO₂RR while maintaining the catalytic efficiency is a great challenge. Here, this work demonstrates the critical roles of the rare earth (RE) compounds (Er₂O₃ and ErF₃) in regulating the activity and selectivity of CO₂RR on cobalt. It is found that the RE compounds not only promote charge transfer but also mediate the reaction paths of CO₂RR and HER. Density functional theory calculations verify that the RE compounds lower the energy barrier of *CO → CO conversion. On the other hand, the RE compounds increase the free energy of HER, which leads to the suppression of HER. As a result, the RE compounds (Er₂O₃ and ErF₃) improve the CO selectivity of cobalt from 48.8 to 69.6%, as well as significantly increase the turnover number by a factor of over 10.

MnO2-Induced Oxidation of Iodide in Frozen Solution

Metal oxides play a critical role in the abiotic transformation of iodine species in natural environments. In this study, we investigated iodide oxidation by manganese dioxides (β-MnO₂, γ-MnO₂, and δ-MnO₂) in frozen and aqueous solutions. The heterogeneous reaction produced reactive iodine (RI) in the frozen phase, and the subsequent thawing of the frozen sample induced the gradual transformation of in situ-formed RI to iodate or iodide, depending on the types of manganese dioxides. The freezing-enhanced production of RI was observed over the pH range of 5.0-9.0, but it decreased with increasing pH. Fulvic acid (FA) can be iodinated by I^-/MnO₂ in aqueous and frozen solutions. About 0.8-8.4% of iodide was transformed to organoiodine compounds (OICs) at pH 6.0-7.8 in aqueous solution, while higher yields (10.4-17.8%) of OICs were obtained in frozen solution. Most OICs generated in the frozen phase contained one iodine atom and were lignin-like compounds according to Fourier transform ion cyclotron resonance/mass spectrometry analysis. This study uncovers a previously unrecognized production pathway of OICs under neutral conditions in frozen environments.

Scalable Synthesis of Holey Deficient 2D Co/NiO Single-Crystal Nanomeshes via Topological Transformation for Efficient Photocatalytic CO2 Reduction

Preparation of holey, single-crystal, 2D nanomaterials containing in-plane nanosized pores is very appealing for the environment and energy-related applications. Herein, an in situ topological transformation is showcased of 2D layered double hydroxides (LDHs) allows scalable synthesis of holey, single-crystal 2D transition metal oxides (TMOs) nanomesh of ultrathin thickness. As-synthesized 2D Co/NiO-2 nanomesh delivers superior photocatalytic CO₂ -syngas conversion efficiency (i.e., V_CO of 32460 µmol h^-1 g^-1 CO and V H 2 ${V_{{{\rm{H}}_2}}}$ of 17840 µmol h^-1 g^-1 H₂ ), with V_CO about 7.08 and 2.53 times that of NiO and 2D Co/NiO-1 nanomesh containing larger pore size, respectively. As revealed in high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM), the high performance of Co/NiO-2 nanomesh primarily originates from the edge sites of nanopores, which carry more defect structures (e.g., atomic steps or vacancies) than basal plane for CO₂ adsorption, and from its single-crystal structure adept at charge transport. Theoretical calculation shows the topological transformation from 2D hydroxide to holey 2D oxide can be achieved, probably since the trace Co dopant induces a lattice distortion and thus a sharp decrease of the dehydration energy of hydroxide precursor. The findings can advance the design of intriguing holey 2D materials with well-defined geometric and electronic properties.

Tuning Electron Transfer in Atomic-Scale Pt-Supported Catalysts for the Alkaline Hydrogen Oxidation Reaction

Developing efficient atomic-scale metal-supported catalysts is of great significance for energy conversion technologies. However, the precise modulation of electron transfer between the metal and supporter in atomic-scale metal-supported catalysts to further improve the catalytic activity is still a major challenge. Herein, we show tunable electron transfer between atomic-scale Pt and tungsten nitride/oxide supports (namely, Pt/WN and Pt/W₁₈O₄₉). Pt/WN with modest electron exchange and Pt/W₁₈O₄₉ with aggressive electron exchange exhibit notably different catalytic activities for the alkaline hydrogen oxidation reaction (HOR), in which Pt/WN shows a 5.7-fold enhancement in HOR intrinsic catalytic performance in comparison to Pt/W₁₈O₄₉. Additionally, the tunable electronic transfer at the interface of Pt/WN and Pt/W₁₈O₄₉, as proven by the theoretical calculation, resulted in the discrepancy of the adsorption free energy of the reaction intermediates, as well as catalytic activity, for the HOR process. Our work provides new insights into the design of advanced atomic-scale metal-supported catalysts for electrocatalysis.

Surface Ru-H Bipyridine Complexes-Grafted TiO2 Nanohybrids for Efficient Photocatalytic CO2 Methanation

A series of novel surface Ru-H bipyridine complexes-grafted TiO₂ nanohybrids were for the first time prepared by a combined procedure of surface organometallic chemistry with post-synthetic ligand exchange for photocatalytic conversion of CO₂ to CH₄ with H₂ as electron and proton donors under visible light irradiation. The selectivity toward CH₄ increased to 93.4% by the ligand exchange of 4,4'-dimethyl-2,2'-bipyridine (4,4'-bpy) with the surface cyclopentadienyl (Cp)-RuH complex and the CO₂ methanation activity was enhanced by 4.4-fold. An impressive rate of 241.2 μL·g^-1·h^-1 for CH₄ production was achieved over the optimal photocatalyst. The femtosecond transient IR absorption results demonstrated that the hot electrons were fast injected in 0.9 ps from the photoexcited surface 4,4'-bpy-RuH complex into the conduction band of TiO₂ nanoparticles to form a charge-separated state with an average lifetime of ca. 50.0 ns responsible for the CO₂ methanation. The spectral characterizations indicated clearly that the formation of CO₂^•- radicals by single electron reduction of CO₂ molecules adsorbed on surface oxygen vacancies of TiO₂ nanoparticles was the most critical step for the methanation. Such radical intermediates were inserted into the explored Ru-H bond to generate Ru-OOCH species and finally CH₄ and H₂O in the presence of H₂.

Modulating the electron structure of Co-3d in Co3O4-x/WO2.72 for boosting peroxymonosulfate activation and degradation of sulfamerazine: Roles of high-valence W and rich oxygen vacancies

Sulfate radical (SO₄^•-)-based heterogonous advanced oxidation processes (AOPs) show promising potential to degrade emerging contaminants, however, regulating the electron structure of a catalyst to promote its catalytic activity is challenging. Herein, a hybrid that consists of Co₃O_4-x nanocrystals decorated on urchin-like WO_2.72 (Co₃O_4-x/WO_2.72) with high-valence W and rich oxygen vacancies (OVs) used to modulate the electronic structure of Co-3d was prepared. The Co₃O_4-x/WO_2.72 that developed exhibited high catalytic activity, activating peroxymonosulfate (PMS), and degrading sulfamerazine (SMR). With the use of Co₃O_4-x/WO_2.72, 100 % degradation of SMR was achieved within 2 min, at a pH of 7, with the reaction rate constant k₁ = 3.09 min^-1. Both characterizations and density functional theory (DFT) calculations confirmed the formation of OVs and the promotion of catalytic activity. The introduction of WO_2.72 greatly regulated the electronic structure of Co₃O_4-x. Specifically, the introduction of high-valence W enabled the Co-3d band centre to be closer to the Fermi level and enhanced electrons (e^-) transfer ability, while the introduction of OVs-Co in Co₃O_4-x promoted the activity of electrons in the Co-3d orbital and the subsequent catalytic reaction. The reactive oxygen species (ROS) were identified as •OH, SO₄^•-, and singlet oxygen (¹O₂) by quenching experiments and electron spin resonance (EPR) analysis. The DFT calculation using the Fukui index indicated the reactive sites in SMR were available for an electrophilic attack, and three degradation pathways were proposed.

Photo-Induced Switching of CO2 Hydrogenation Pathway towards CH3 OH Production over Pt@UiO-66-NH2 (Co)

It is highly desired to achieve controllable product selectivity in CO₂ hydrogenation. Herein, we report light-induced switching of reaction pathways of CO₂ hydrogenation towards CH₃ OH production over actomically dispersed Co decorated Pt@UiO-66-NH₂ . CO, being the main product in the reverse water gas shift (RWGS) pathway under thermocatalysis condition, is switched to CH₃ OH via the formate pathway with the assistance of light irradiation. Impressively, the space-time yield of CH₃ OH in photo-assisted thermocatalysis (1916.3 μmol g_cat ^-1  h^-1 ) is about 7.8 times higher than that without light at 240 °C and 1.5 MPa. Mechanism investigation indicates that upon light irradiation, excited UiO-66-NH₂ can transfer electrons to Pt nanoparticles and Co sites, which can efficiently catalyze the critical elementary steps (i.e., CO₂ -to-*HCOO conversion), thus suppressing the RWGS pathway to achieve a high CH₃ OH selectivity.

Study on the photocatalytic properties differences between the 1-D and 3-D W18O49 particles†

The morphology of W₁₈O₄₉ catalysts has a significant effect on their photocatalytic performance. Herein, we successfully prepared two commonly used W₁₈O₄₉ photocatalysts just by changing the reaction temperature in the hydrothermal system, namely 1-D W₁₈O₄₉ nanowires (1-D W₁₈O₄₉) and 3-D urchin-like W₁₈O₄₉ particles (3-D W₁₈O₄₉), and evaluated the difference of their photocatalytic performances by taking the degradation of methylene blue (MB) as an example. Remarkably, 3-D W₁₈O₄₉ exhibited an impressive photocatalytic degradation performance towards MB with photocatalytic reaction rates of 0.00932 min⁻¹, which was about 3 times higher than that of 1-D W₁₈O₄₉. The comprehensive characterization and control experiments could further reveal that the hierarchical structure of 3-D W₁₈O₄₉ brought higher BET surface areas, stronger light harvesting, faster separation of photogenerated charges and so on, which was the main reason for its better photocatalytic performance. ESR results confirmed that the main active substances were superoxide radicals (˙O₂⁻) and hydroxyl radicals (˙OH). This work aims to explore the intrinsic relationship between the morphology and photocatalytic properties of W₁₈O₄₉ catalysts, so as to provide a theoretical basis in the morphology selection of W₁₈O₄₉ or its composite materials in the field of photocatalysis.

Comprehensive characterization and control experiments were used to deeply explore the intrinsic relationship between the morphology and photocatalytic properties of W₁₈O₄₉ catalysts.

Dual-plasmon-enhanced nitrophenol hydrogenation over W18O49–Au heterostructures studied at the single-particle level

The dual-plasmonic W18O49–Au heterostructure exhibited enhanced catalytic performance in nitrophenol hydrogenation. The HEI process and coupling effect were demonstrated by single-particle spectroscopy and FDTD simulation.

Design and preparation of highly active TiO2 photocatalysts by modulating their band structure

Titanium dioxide photocatalysts with high reduction potential and visible light response hold great promise in photochemical conversion. Here, we used a simple glycine doping method to synthesize novel N-TiO2@C photocatalysts with upward shifted conduction bands and narrowed band gaps as well as inhibited recombination of photoinduced electron-hole pairs. The N-TiO2@C photocatalysts exhibited higher visible light response and remarkably enhanced photocatalytic activity in the production of nicotinamide adenine dinucleotide (NADH) by photomediated reduction of NAD+ without any electron mediator. The yield of NADH was up to 70.3 % far greater than that of the undoped TiO2 (11.3 %), and it stabilized at ca. 60 % after 10 cycles. The viability of coupling NADH regeneration with enzymatic reaction (alcohol dehydrogenase) was established in aldehyde reduction where formaldehyde was specifically reduced to methanol. These findings shed new light on the modulation of the band structure of semiconductors and develop an electron mediator free strategy for NADH-dependent artificial photosynthesis through coupled photocatalytic and enzymatic approaches.

Progress and perspectives on 1D nanostructured catalysts applied in photo(electro)catalytic reduction of CO2

Reducing CO₂ into value-added chemicals and fuels by artificial photosynthesis (photocatalysis and photoelectrocatalysis) is one of the considerable solutions to global environmental and energy issues. One-dimensional (1D) nanostructured catalysts (nanowires, nanorods, nanotubes and so on.) have attracted extensive attention due to their superior light-harvesting ability, co-catalyst loading capacity, and high carrier separation rate. This review analyzed the basic principle of the photo(electro)catalytic CO₂ reduction reaction (CO₂ RR) briefly. The preparation methods and properties of 1D nanostructured catalysts are introduced. Next, the applications of 1D nanostructured catalysts in the field of photo(electro)catalytic CO₂ RR are introduced in detail. In particular, we introduced the design of composite catalysts with 1D nanostructures, for example loading 0D, 1D, 2D, and 3D materials on a 1D nanostructured semiconductor to construct a heterojunction to optimize the photo-response range, carrier separation and transport efficiency, CO₂ adsorption and activation capacity, and stability of the catalyst. Finally, the development prospects of 1D nanostructured catalysts are discussed and summarized. This review can provide guidance for the rational design of advanced catalysts for photo(electro)catalytic CO₂ RR.

Review on Catalytic Oxidation of VOCs at Ambient Temperature

As an important air pollutant, volatile organic compounds (VOCs) pose a serious threat to the ecological environment and human health. To achieve energy saving, carbon reduction, and safe and efficient degradation of VOCs, ambient temperature catalytic oxidation has become a hot topic for researchers. Firstly, this review systematically summarizes recent progress on the catalytic oxidation of VOCs with different types. Secondly, based on nanoparticle catalysts, cluster catalysts, and single-atom catalysts, we discuss the influence of structural regulation, such as adjustment of size and configuration, metal doping, defect engineering, and acid/base modification, on the structure-activity relationship in the process of catalytic oxidation at ambient temperature. Then, the effects of process conditions, such as initial concentration, space velocity, oxidation atmosphere, and humidity adjustment on catalytic activity, are summarized. It is further found that nanoparticle catalysts are most commonly used in ambient temperature catalytic oxidation. Additionally, ambient temperature catalytic oxidation is mainly applied in the removal of easily degradable pollutants, and focuses on ambient temperature catalytic ozonation. The activity, selectivity, and stability of catalysts need to be improved. Finally, according to the existing problems and limitations in the application of ambient temperature catalytic oxidation technology, new prospects and challenges are proposed.

Isolating Single Sn Atoms in CuO Mesocrystal to Form Ordered Atomic Interfaces: An Effective Strategy for Designing Highly Efficient Mesocrystal Catalysts

Tuning the electronic structures of mesocrystals at the atomic level is an effective approach to obtaining unprecedented properties. Here, a lattice-confined strategy to obtain isolated single-site Sn atoms in CuO mesocrystals to improve catalytic performance is reported. The Sn/CuO mesocrystal composite (Sn/CuO MC) has ordered Sn-O-Cu atomic interfaces originated from the long-range ordering of the CuO mesocrystal itself. X-ray absorption fine structure measurements confirm that the positively charged Sn atoms can tune the electronic structure of the Cu atoms to some extent in Sn/CuO MC, quite different from that in the conventional single-atom Sn-modified CuO nanoparticles and nanoparticulate SnO₂ -modified CuO mesocrystal catalysts. When tested for the Si hydrochlorination reaction to produce trichlorosilane, Sn/CuO MC exhibits significantly better performances than the above two catalysts. Theoretical calculations further reveal the electronic modification to the active Cu component and the induced improvement in HCl adsorption, and thus enhance the catalytic performance. This work demonstrates how to design efficient metal oxide mesocrystal catalysts through an electronic structure modification approach.

Optimizing the semiconductor–metal-single-atom interaction for photocatalytic reactivity

Metal single-atom (MSA) catalysts with 100% metal atom utilization and unique electronic properties are attractive cocatalysts for efficient photocatalysis when coupled with semiconductors. Owing to the absence of a metal-metal bond, MSA sites are exclusively coordinated with the semiconductor photocatalyst, featuring a chemical-bond-driven tunable interaction between the semiconductor and the metal single atom. This semiconductor-MSA interaction is a platform that can facilitate the separation/transfer of photogenerated charge carriers and promote the subsequent catalytic reactions. In this Review, we first introduce the fundamental physicochemistry related to the semiconductor-MSA interaction. We highlight the ligand effect on the electronic structures, catalytic properties and functional mechanisms of the MSA cocatalyst through the semiconductor-MSA interaction. Then, we categorize the state-of-the-art experimental and theoretical strategies for the construction of the efficient semiconductor-MSA interaction at the atomic scale for a wide range of photocatalytic reactions. The examples described include photocatalytic water splitting, CO₂ reduction and organic synthesis. We end by outlining strategies on how to further advance the semiconductor-MSA interaction for complex photocatalytic reactions involving multiple elementary steps. We provide atomic and electronic-scale insights into the working mechanisms of the semiconductor-MSA interaction and guidance for the design of high-performance semiconductor-MSA interface photocatalytic systems.

Implanting CoOx Clusters on Ordered Macroporous ZnO Nanoreactors for Efficient CO2 Photoreduction

Despite suffering from slow charge-carrier mobility, photocatalysis is still an attractive and promising technology toward producing green fuels from solar energy. An effective approach is to design and fabricate advanced architectural materials as photocatalysts to enhance the performance of semiconductor-based photocatalytic systems. Herein, metal-organic-framework-derived hierarchically ordered porous nitrogen and carbon co-doped ZnO (N-C-ZnO) structures are developed as nanoreactors with decorated CoO_x nanoclusters for CO₂ -to-CO conversion driven by visible light. Introduction of hierarchical nanoarchitectures with highly ordered interconnected meso-macroporous channels shows beneficial properties for photocatalytic reduction reactions, including enhanced mobility of charge carriers throughout the highly accessible framework, maximized exposure of active sites, and inhibited recombination of photoinduced charge carriers. Density functional theory calculations further reveal the key role of CoO_x nanoclusters with high affinity to CO₂ molecules, and the CoO bonds formed on the surface of the composite exhibit stronger charge redistribution. As a result, the obtained CoO_x /N-C-ZnO demonstrates enhanced photocatalysis performance in terms of high CO yield and long-term stability.

VO4 -Modified Layered Double Hydroxides Nanosheets for Highly Selective Photocatalytic CO2 Reduction to C1 Products

The conversion of CO₂ into high-value added chemicals driven by solar energy is an effective way to solve environmental problems, which is, however, largely restricted by the competition reaction of the hydrogen evolution reaction (HER) and easy electron-hole recombination, etc. Herein, VO₄ -supported ultrathin NiMgV-layered double hydroxide (V/NiMgV-LDH) nanosheets are successfully fabricated, and the extended X-ray absorption fine structure (EXAFS) and density function theory (DFT) calculations reveal that VO₄ species are located on the top of V atoms in the NiMgV-LDH laminate. The V/NiMgV-LDH is proved to be highly efficient for the photocatalytic CO₂ reduction reaction (CO₂ PR) with high selectivity of 99% for C1 products and nearly no HER (<1%) takes place under visible light. Contrast experiments using NiMgV-LDH as the catalyst for CO₂ PR show a CO selectivity of 71.40% and a H₂ selectivity of 28.11%. Such excellent performance of V/NiMgV-LDH can be attributed to the following reasons: 1) the V/NiMgV-LDH modulates the band structure and promotes the separation of electrons and holes; 2) strong bonding between V/NiMgV-LDH and CO* and H* facilitates the hydrogenation to form CH₄ and inhibits the formation of by-product H₂ at the same time.

Naphthalene Diimide-Based Donor-Acceptor-Donor Small Molecules as Metal-Free Organocatalysts for Photocatalytic CO2 Reaction

The application of organic small molecules as metal-free photocatalysts for light-driven photoreduction of carbon dioxide (CO₂) has seldom been explored. This work developed four naphthalene diimide (NDI)-derived donor-acceptor-donor small molecules with different numbers of thiophene units, namely, NDI-2T, NDI-TT, NDI-4T, and NDI-6T, as metal-free photocatalysts to catalyze the reduction of CO₂ under irradiation with an air mass 1.5G solar simulator at one-sun intensity. The structure-property relationship was investigated by exploring the effects of the electron-donating ability of the donor units on the optical properties, redox potential, electron-hole distribution, and exciton lifetime. NDI-6T exhibited the most red-shifted absorption, longest exciton lifetime, and strongest electron-hole separation. However, the large upshift in oxidation potential because of the elevated electron-donating ability of the hexathiophene unit significantly reduced the driving force for catalyst regeneration, leading to poor catalytic performance. Alternatively, NDI-4T possessed proper redox potentials, reduced charge-transfer resistance, and excellent photocurrent intensity; therefore, it effectively converted CO₂ to a single product of CO in the presence of water as an electron donor without a sacrificial reagent or cocatalyst with a product yield of 168.6 μmol g_cat^-1 24 h^-1, which was considerably higher than those of NDI-TT (111.9 μmol g_cat^-1 24 h^-1), NDI-2T (88.4 μmol g_cat^-1 24 h^-1), and NDI-6T (40.5 μmol g_cat^-1 24 h^-1). This study provides a practical guideline for the molecular design of conjugated organic molecules as promising photocatalysts for CO₂ photoreduction.

Dual-quantum-dots heterostructure with confined active interface for promoted photocatalytic NO abatement

Constructing heterostructure is an effective way to fabricate advanced photocatalysts. However, the catalytic performance of typical common multi-dimensional bulk heterostructure still suffers from the limited active interface and inefficient carrier migration. Herein, we successfully synthesize the SnO₂/Cs₃Bi₂I₉ dual-quantum-dots nanoheterostructure (labeled as SCX, X = 1, 2, 3) for efficiently and stably photocatalytic NO removal under visible light irradiation. The NO removal rate of SC2 is almost 8 and 17 times higher than that of the single SnO₂ and Cs₃Bi₂I₉, respectively. Moreover, the SC2 photocatalyst shows only 3 % attenuation after five consecutive cycles, demonstrating good photocatalytic stability. Systematic experimental characterization and theoretical density functional theory calculations revealed that the high activity and stability of SCX originated from the efficient charge transfer at the confined interface between SnO₂ and Cs₃Bi₂I₉ quantum dots. This work provides a new perspective for constructing innovative dual-quantum-dots nanoheterostructure and assesses their potential in photocatalytic environmental applications.