Synthesis and Characterization of Highly Magnetized Nanocrystalline Co30Fe70Alloy by Chemical Reduction

Preparation of In/Sn Nanoparticles (In3Sn and InSn4) by Wet Chemical One-Step Reduction and Performance Study

The preparation of binary alloys by surfactant-assisted chemical reduction in aqueous solution at room temperature has become a hot topic. In this article low melting point tin/indium (Sn/In) nanoparticles are synthesized. The formation process of the alloy was studied. Scanning electron microscopy, energy spectrometry, and X-ray diffraction are used to determine the morphology, composition, and crystal structure of the nanoparticles. Study found that fully alloyed indium-tin nanoparticles can be obtained by wet chemical method and the main phases of indium-tin alloy are β-phase (In3Sn) and γ-phase (InSn4). However, the Sn phase appears at a low content of indium (40 wt%). When the content of indium increases to 45 (wt%), the tin phase disappears. In addition, the most important finding is that the composition of the indium-tin alloy can be changed by ratio control, and the content of In3Sn increases with the increase of indium content. The relative content of In3Sn attains a maximum when the content of indium increases to 60 (wt%). In contrast, the content of InSn4 decreases. Finally, differential scanning calorimetry measurements is performed to understand the melting behavior of the nanoparticles and low melting temperatures are achieved for a wide range of indium compositions (from 40% to 60%). The melting temperature is found to be in the range of 125–132 °C and it increased with increasing In3Sn (also the increase of indium content). This gives us a new understanding into the binary alloy nano-system and gives important information for the application of low temperature alloy solders. The choice of composition can be based on the corresponding melting point.

Influence of reduction temperature on composition, particle size, and magnetic properties of CoFe alloy nanomaterials derived from layered double hydroxide precursors

CoFe alloy nanomaterials with high thermal stability and excellent magnetic properties were prepared through reduction of layered double hydroxides precursors at various temperatures.

Enhanced magnetization in highly crystalline and atomically mixed bcc Fe-Co nanoalloys prepared by hydrogen reduction of oxide composites

Fe(x)Co(100-x) nanoalloys (NAs) with 20 ≤ x ≤ 80 were prepared by hydrogen reduction of Fe-Co oxide nano-composites, which were composed of mixed phases (or domains) of Fe(2)O(3) and CoO. In situ X-ray diffraction (XRD) measurements using synchrotron radiation clearly showed development of a solid-solution Fe-Co phase by hydrogen reduction from the oxide composites. High-resolution transmission electron microscopy (TEM), high-angle annular dark-field scanning TEM and powder XRD revealed that Fe-Co NAs form a single crystal structure and the two elements are mixed homogeneously. The saturation magnetization depends on the size and metal composition and shows the highest value (250 emu g(-1)) for the Fe(70)Co(30) NA in the size range of 30-55 nm, which is comparable to that of the Fe(70)Co(30) bulk alloy (245 emu g(-1)). This high magnetization is attributable to high crystallinity and homogeneous mixing of constituent atoms, which are attained by thermal treatment of oxide phases under a hydrogen atmosphere.

Preparation of Monodisperse Iron Oxide Nanoparticles via the Synthesis and Decomposition of Iron Fatty Acid Complexes

Iron fatty acid complexes (IFACs) are prepared via the dissolution of porous hematite powder in hot unsaturated fatty acid. The IFACs are then decomposed in five different organic solvents under reflux conditions in the presence of the respective fatty acid. The XRD analysis results indicate that the resulting NPs comprise a mixture of wustite, magnetite, and maghemite phases. The solvents with a higher boiling point prompt the formation of larger NPs containing wustite as the major component, while those with a lower boiling point produce smaller NPs with maghemite as the major component. In addition, it is shown that unstable NPs with a mixed wustite-magnetite composition can be oxidized to pure maghemite by extending the reaction time or using an oxidizing agent.

Vast Magnetic Monolayer Film with Surfactant-Stabilized Fe3O4 Nanoparticles Using Langmuir−Blodgett Technique

Although several methods (e.g., self-assembly, spin coating, etc.) have been explored for making a monolayer film of nanoparticles, the monolayer on a substrate is typically smaller than 1 micromx1 microm in certain regions. The approach is not ideally suitable for generating a highly ordered and close-packed homogeneous vast monolayer of nanoparticles, which is potentially important for applications. In this report, the preparation of the vast monolayer films of Fe3O4 nanoparticles with a wide range such as that over 3.25 micromx3.95 microm is reported. Their TEM images showed a two-dimensional assembly of Fe3O4 nanoparticles, demonstrating the uniformity of these nanoparticles. The formation of a Langmuir monolayer of the oleic acid-coated Fe3O4 nanoparticles mixed with stearic acid molecules at the air/water interface and its stability were studied with a pressure-area isotherm curve. TEM and BAM studies demonstrated that increasing surface pressure resulted in a transition from well-separated domains of nanoparticles complex to well-compressed, monoparticulate layers.