A novel high specific surface area conducting paper material composed of polypyrrole and Cladophora cellulose

Assessment of the Alga Cladophora glomerata as a Source for Cellulose Nanocrystals

Nanocellulose is isolated from cellulosic fibers and exhibits many properties that macroscale cellulose lacks. Cellulose nanocrystals (CNCs) are a subcategory of nanocellulose made of stiff, rodlike, and highly crystalline nanoparticles. Algae of the order Cladophorales are the source of the longest cellulosic nanocrystals, but manufacturing these CNCs is not well-studied. So far, most publications have focused on the applications of this material, with the basic manufacturing parameters and material properties receiving little attention. In this article, we investigate the entirety of the current manufacturing process from raw algal biomass (Cladophora glomerata) to the isolation of algal cellulose nanocrystals. Yields and cellulose purities are investigated for algal cellulose and the relevant process intermediates. Furthermore, the effect of sulfuric acid hydrolysis, which is used to convert cellulose into CNCs and ultimately determines the material properties and some of the sustainability aspects, is examined and compared to literature results on wood cellulose nanocrystals. Long (>4 μm) CNCs form a small fraction of the overall number of CNCs but are still present in measurable amounts. The results define essential material properties for algal CNCs, simplifying their future use in functional cellulosic materials.

Fabrication of Hollow Nanocones Membrane with an Extraordinary Surface Area as CO2 Sucker

Recently, more and more attention has been paid to the development of eco-friendly solid sorbents that are cost-effective, noncorrosive, have a high gas capacity, and have low renewable energy for CO₂ capture. Here, we claimed the fabrication of a three-dimensional (3D) film of hollow nanocones with a large surface area (949.5 m²/g), a large contact angle of 136.3°, and high surface energy. The synthetic technique is based on an electrochemical polymerization process followed by a novel and simple strategy for pulling off the formed layers as a membrane. Although the polymer-coated substrates were reported previously, the membrane formation has not been reported elsewhere. The detachable capability of the manufactured layer as a membrane braked the previous boundaries and allows the membrane’s uses in a wide range of applications. This 3D hollow nanocones membrane offer advantages over conventional ones in that they combine a π-electron-rich (aromatic ring), hydrophobicity, a large surface area, multiple amino groups, and a large pore volume. These substantial features are vital for CO₂ capturing and storage. Furthermore, the hydrophobicity characteristic and application of the formed polymer as a CO₂ sucker were investigated. These results demonstrated the potential of the synthesized 3D hollow polymer to be used for CO₂ capturing with a gas capacity of about 68 mg/g and regeneration ability without the need for heat up.

Thermal insulating, light-weight and conductive cellulose/aramid nanofibers composite aerogel for pressure sensing

Conductive nanocellulose aerogels have attracted significant attention in pressure sensing for wearable devices owing to lightweight, sustainability and good chemical stability. Limited by its flammability and weak mechanical properties, aramid nanofiber (ANF) was designed as reinforcement to overcome the shortcoming mentioned above. Herein, the unidirectional freeze casting method was proposed to fabricate nanocellulose/aramid nanofiber (CA) aerogel. Then, the CA/PPy (CAP) aerogel was obtained by using the oriented structure of CA aerogel as a template for inducing conductive polypyrrole (PPy) in-situ formation inside the composite aerogel. The conductive aerogel with the ordered microstructure exhibited the anisotropic mechanical properties and thermal conductivity. And it could withstand high temperature without any destruction phenomenon. Moreover, the aerogel sensor revealed high strain sensitivity and satisfactory electrochemical performance. Lightweight CAP aerogel with controllable alignment, sensitive sensing property and thermal stability is very promising in pressure sensor under some extreme conditions.

Multi-Substrate Biofuel Cell Utilizing Glucose, Fructose and Sucrose as the Anode Fuels

A significant problem still exists with the low power output and durability of the bioelectrochemical fuel cells. We constructed a fuel cell with an enzymatic cascade at the anode for efficient energy conversion. The construction involved fabrication of the flow-through cell by three-dimensional printing. Gold nanoparticles with covalently bound naphthoquinone moieties deposited on cellulose/polypyrrole (CPPy) paper allowed us to significantly improve the catalysis rate, both at the anode and cathode of the fuel cell. The enzymatic cascade on the anode consisted of invertase, mutarotase, Flavine Adenine Dinucleotide (FAD)-dependent glucose dehydrogenase and fructose dehydrogenase. The multi-substrate anode utilized glucose, fructose, sucrose, or a combination of them, as the anode fuel and molecular oxygen were the oxidant at the laccase-based cathode. Laccase was adsorbed on the same type of naphthoquinone modified gold nanoparticles. Interestingly, the naphthoquinone modified gold nanoparticles acted as the enzyme orienting units and not as mediators since the catalyzed oxygen reduction occurred at the potential where direct electron transfer takes place. Thanks to the good catalytic and capacitive properties of the modified electrodes, the power density of the sucrose/oxygen enzymatic fuel cells (EFC) reached 0.81 mW cm-2, which is beneficial for a cell composed of a single cathode and anode.

Paper-based sorptive phases for microextraction and sensing

The simplification of the analytical procedures, including cost-effective materials and detectors, is a current research trend. In this context, paper has been identified as a useful material thanks to its low price and high availability in different compositions (office, filter, chromatographic). Its porosity, flexibility, and planar geometry permit the design of flow-through devices compatible with most instrumental techniques. This article provides a general overview of the potential of paper, as substrate, on the simplification of analytical chemistry methodologies. The design of paper-based sorptive phases is considered in-depth, and the different functionalization strategies are described. Considering our experience in sample preparation, special attention has been paid to the use of these phases under the classical microextraction-analysis workflow, which usually includes a chromatographic separation of the analytes before their determination. However, the interest of these materials extends beyond this field as they can be easily implemented into spectroscopic and electrochemical sensors. Finally, the direct analysis of paper substrates in mass spectrometry, in the so-called paper-spray technique is also discussed. This review is more focused on presenting ideas rather than the description of specific applications to draw a general picture of the potential of these materials.

Temperate-zone cultivation of Oedogonium in municipal wastewater effluent to produce cellulose and oxygen

Cultivation of the filamentous chlorophyte Oedogonium in municipal wastewater effluent is known to improve water quality and yield lipid- and protein-rich biomass for industrial applications. Chlorophyte celluloses, whose molecular organization and physical traits differ from those of plants, represent yet another valuable extractive, and algal oxygen production is of economic value in wastewater treatment. Consequently, we explored cellulose and oxygen production from Oedogonium biomass batch-cultivated in treated secondary municipal wastewater effluent. We compared biomass, cellulose, and oxygen production outside and within an adjacent greenhouse, under differing dissolved CO2 and pH conditions, and during temperate-zone seasonal change from summer through fall. Overall production did not differ within or outside the greenhouse, but outside production was higher in summer and lower in fall as air temperatures declined. Batch cultivation offered advantages, but high levels of mixing and CO2 were essential to maintain neutral pH for optimal algal growth and oxygen production.

Nanocellulose for Energy Storage Systems: Beyond the Limits of Synthetic Materials

The ongoing surge in demand for high-performance energy storage systems inspires the relentless pursuit of advanced materials and structures. Components of energy storage systems are generally based on inorganic/metal compounds, carbonaceous substances, and petroleum-derived hydrocarbon chemicals. These traditional materials, however, may have difficulties fulfilling the ever-increasing requirements of energy storage systems. Recently, nanocellulose has garnered considerable attention as an exceptional 1D element due to its natural abundance, environmental friendliness, recyclability, structural uniqueness, facile modification, and dimensional stability. Recent advances and future outlooks of nanocellulose as a green material for energy storage systems are described, with a focus on its application in supercapacitors, lithium-ion batteries (LIBs), and post-LIBs. Nanocellulose is typically classified as cellulose nanofibril (CNF), cellulose nanocrystal (CNC), and bacterial cellulose (BC). The unusual 1D structure and chemical functionalities of nanocellulose bring unprecedented benefits to the fabrication and performance of energy storage materials and systems, which lie far beyond those achievable with conventional synthetic materials. It is believed that this progress report can stimulate research interests in nanocellulose as a promising material, eventually widening material horizons for the development of next-generation energy storage systems, that will lead us closer to so-called Battery-of-Things (BoT) era.

A new method to produce cellulose nanofibrils from microalgae and the measurement of their mechanical strength

Despite the enormous potential of cellulose nanofibrils (CNFs) as a reinforcing filler in various fields, the use of them has been limited by high-energy mechanical treatments that require a lot of energy and time consumption. To reduce the demands of energy and time required for mechanical treatments, microalgae, in particular, Nannochloropsis oceanica, which has small size, rapid growth rate, and high productivity was used as a CNFs source. This study obtains the CNFs by lipid/protein extraction, purification, and TEMPO-mediated oxidation processes under gentle mixing without high-energy mechanical treatments. Furthermore, to evaluate the applicability of microalgal CNFs as a reinforcing filler, this study estimated the mechanical strength of the fibrils by the sonication-induced scission method. To achieve a precise estimation, an effective method to distinguish straight fibrils from buckled fibrils was also developed, and subsequently, only straight fibrils were used to calculate the mechanical strength in the sonication-induced scission method. Consequently, the tensile strength of the N. oceanica CNFs is around 3-4GPa on average which is comparable with the mechanical strength of general reinforcing fillers and even higher than that of wood CNFs. Thus, this study has shown that the newly proposed simplified method using N. oceanica is very successful in producing CNFs with great mechanical strength which could be used in various reinforcement fields.

Nanocellulose as a sustainable biomass material: structure, properties, present status and future prospects in biomedical applications

Nanocellulose, extracted from the most abundant biomass material cellulose, has proved to be an environmentally friendly material with excellent mechanical performance owing to its unique nano-scaled structure, and has been used in a variety of applications as engineering and functional materials. The great biocompatibility and biodegradability, in particular, render nanocellulose promising in biomedical applications. In this review, the structure, treatment technology and properties of three different nanocellulose categories, i.e., nanofibrillated cellulose (NFC), nanocrystalline cellulose (NCC) and bacterial nanocellulose (BNC), are introduced and compared. The cytotoxicity, biocompatibility and frontier applications in biomedicine of the three nanocellulose categories were the focus and are detailed in each section. Future prospects concerning the cytotoxicity, applications and industrial production of nanocellulose are also discussed in the last section.

Nanocellulose coupled flexible polypyrrole@graphene oxide composite paper electrodes with high volumetric capacitance

A robust and compact freestanding conducting polymer-based electrode material based on nanocellulose coupled polypyrrole@graphene oxide paper is straightforwardly prepared via in situ polymerization for use in high-performance paper-based charge storage devices, exhibiting stable cycling over 16,000 cycles at 5 A g(-1) as well as the largest specific volumetric capacitance (198 F cm(-3)) so far reported for flexible polymer-based electrodes.

Role of co-vapors in vapor deposition polymerization

Polypyrrole (PPy)/cellulose (PPCL) composite papers were fabricated by vapor phase polymerization. Importantly, the vapor-phase deposition of PPy onto cellulose was assisted by employing different co-vapors namely methanol, ethanol, benzene, water, toluene and hexane, in addition to pyrrole. The resulting PPCL papers possessed high mechanical flexibility, large surface-to-volume ratio, and good redox properties. Their main properties were highly influenced by the nature of the co-vaporized solvent. The morphology and oxidation level of deposited PPy were tuned by employing co-vapors during the polymerization, which in turn led to change in the electrochemical properties of the PPCL papers. When methanol and ethanol were used as co-vapors, the conductivities of PPCL papers were found to have improved five times, which was likely due to the enhanced orientation of PPy chain by the polar co-vapors with high dipole moment. The specific capacitance of PPCL papers obtained using benzene, toluene, water and hexane co-vapors was higher than those of the others, which is attributed to the enlarged effective surface area of the electrode material. The results indicate that the judicious choice and combination of co-vapors in vapor-deposition polymerization (VDP) offers the possibility of tuning the morphological, electrical, and electrochemical properties of deposited conducting polymers.

Asymmetric supercapacitors based on carbon nanofibre and polypyrrole/nanocellulose composite electrodes

Asymmetric, all-organic supercapacitors (containing an aqueous electrolyte), exhibiting a capacitance of 25 F g⁻¹ (or 2.3 F cm⁻²) at a current density of 20 mA cm⁻² and a maximum cell voltage of 1.6 V, are presented.

Freestanding nanocellulose-composite fibre reinforced 3D polypyrrole electrodes for energy storage applications

It is demonstrated that 3D nanostructured polypyrrole (3D PPy) nanocomposites can be reinforced with PPy covered nanocellulose (PPy@nanocellulose) fibres to yield freestanding, mechanically strong and porosity optimised electrodes with large surface areas. Such PPy@nanocellulose reinforced 3D PPy materials can be employed as free-standing paper-like electrodes in symmetric energy storage devices exhibiting cell capacitances of 46 F g(-1), corresponding to specific electrode capacitances of up to ∼185 F g(-1) based on the weight of the electrode, and 5.5 F cm(-2) at a current density of 2 mA cm(-2). After 3000 charge/discharge cycles at 30 mA cm(-2), the reinforced 3D PPy electrode material also showed a cell capacitance corresponding to 92% of that initially obtained. The present findings open up new possibilities for the fabrication of high performance, low-cost and environmentally friendly energy-storage devices based on nanostructured paper-like materials.

A size-exclusion nanocellulose filter paper for virus removal

This is the first time a 100% natural, unmodified nanofibrous polymer-based membrane is demonstrated capable of removing viruses solely based on the size-exclusion principle, with a log10 reduction value (LRV) ≥ 6.3 as limited by the assay lower detection limit and the feed virus titre, thereby matching the performance of industrial synthetic polymer virus removal filters.

Is there a future for electrochemically assisted hemodialysis? Focus on the application of polypyrrole–nanocellulose composites

This work summarizes the various aspects of using electrochemically assisted solute removal techniques in hemodialysis with a focus on blood electrodialysis and electrochemically controlled uremic retention solute removal using polypyrrole. In particular, the feasibility of using highly porous conductive polypyrrole–Cladophora cellulose membranes for hemodialysis are overviewed as a part of our dedicated research efforts during the past 4 years. The potential benefits and the current limitations associated with using the electrochemically controlled uremic retention solute removal techniques are discussed in detail.

25th anniversary article: organic photovoltaic modules and biopolymer supercapacitors for supply of renewable electricity: a perspective from Africa

The role of materials in civilization is well demonstrated over the centuries and millennia, as materials have come to serve as the classifier of stages of civilization. With the advent of materials science, this relation has become even more pronounced. The pivotal role of advanced materials in industrial economies has not yet been matched by the influence of advanced materials during the transition from agricultural to modern societies. The role of advanced materials in poverty eradication can be very large, in particular if new trajectories of social and economic development become possible. This is the topic of this essay, different in format from the traditional scientific review, as we try to encompass not only two infant technologies of solar energy conversion and storage by means of organic materials, but also the social conditions for introduction of the technologies. The development of organic-based photovoltaic energy conversion has been rapid, and promises to deliver new alternatives to well-established silicon photovoltaics. Our recent development of organic biopolymer composite electrodes opens avenues towards the use of renewable materials in the construction of wooden batteries or supercapacitors for charge storage. Combining these new elements may give different conditions for introduction of energy technology in areas now lacking electrical grids, but having sufficient solar energy inputs. These areas are found close to the equator, and include some of the poorest regions on earth.

Tailoring porosities and electrochemical properties of composites composed of microfibrillated cellulose and polypyrrole

The porosities of composites of polypyrrole and nanocellulose can be tailored from 30 to 98% with ∼10% increments enabling the electrochemical behavior of the materials to be readily controlled.

Electrical field-induced extraction and separation techniques: promising trends in analytical chemistry--a review

Sample preparation is an important issue in analytical chemistry, and is often a bottleneck in chemical analysis. So, the major incentive for the recent research has been to attain faster, simpler, less expensive, and more environmentally friendly sample preparation methods. The use of auxiliary energies, such as heat, ultrasound, and microwave, is one of the strategies that have been employed in sample preparation to reach the above purposes. Application of electrical driving force is the current state-of-the-art, which presents new possibilities for simplifying and shortening the sample preparation process as well as enhancing its selectivity. The electrical driving force has scarcely been utilized in comparison with other auxiliary energies. In this review, the different roles of electrical driving force (as a powerful auxiliary energy) in various extraction techniques, including liquid-, solid-, and membrane-based methods, have been taken into consideration. Also, the references have been made available, relevant to the developments in separation techniques and Lab-on-a-Chip (LOC) systems. All aspects of electrical driving force in extraction and separation methods are too specific to be treated in this contribution. However, the main aim of this review is to provide a brief knowledge about the different fields of analytical chemistry, with an emphasis on the latest efforts put into the electrically assisted membrane-based sample preparation systems. The advantages and disadvantages of these approaches as well as the new achievements in these areas have been discussed, which might be helpful for further progress in the future.

A Nanocellulose Polypyrrole Composite Based on Tunicate Cellulose

The water-dispersed conductive polypyrrole (PPy) was prepared via thein situoxidative chemical polymerization by using ammonium persulfate (APS) as oxidant and tunicate cellulose nanocrystals (T-CNs) as a dopant and template for tuning the morphologies of PPy nanoparticles. Highly flexible paper-like materials of PPy/T-CNs nanocomposites with high electrical conductivity values and good mechanical properties were prepared. The structure of nanocomposites of PPy/T-CNs was investigated by using Fourier transform infrared spectroscopy. Scanning electron microscopy and transmission electron microscopy analyses of the composites revealed that PPy consisted of nanoparticles about 2.5 nm in mean size to form a continuous coating covered on the T-CNs. The diameters of the PPy nanoparticles increased from 10 to 100 nm with the increasing pyrrole amount. Moreover, electrical properties of the obtained PPy/T-CNs films were studied using standard four-probe technique and the electrical conductivity could be as high as 10−3 S/cm.

Haemocompatibility and ion exchange capability of nanocellulose polypyrrole membranes intended for blood purification

Composites of nanocellulose and the conductive polymer polypyrrole (PPy) are presented as candidates for a new generation of haemodialysis membranes. The composites may combine active ion exchange with passive ultrafiltration, and the large surface area (about 80 m(2) g(-1)) could potentially provide compact dialysers. Herein, the haemocompatibility of the novel membranes and the feasibility of effectively removing small uraemic toxins by potential-controlled ion exchange were studied. The thrombogenic properties of the composites were improved by applying a stable heparin coating. In terms of platelet adhesion and thrombin generation, the composites were comparable with haemocompatible polymer polysulphone, and regarding complement activation, the composites were more biocompatible than commercially available membranes. It was possible to extract phosphate and oxalate ions from solutions with physiological pH and the same tonicity as that of the blood. The exchange capacity of the materials was found to be 600 ± 26 and 706 ± 31 μmol g(-1) in a 0.1 M solution (pH 7.4) and in an isotonic solution of phosphate, respectively. The corresponding values with oxalate were 523 ± 5 in a 0.1 M solution (pH 7.4) and 610 ± 1 μmol g(-1) in an isotonic solution. The heparinized PPy-cellulose composite is consequently a promising haemodialysis material, with respect to both potential-controlled extraction of small uraemic toxins and haemocompatibility.

High-capacity conductive nanocellulose paper sheets for electrochemically controlled extraction of DNA oligomers

Highly porous polypyrrole (PPy)-nanocellulose paper sheets have been evaluated as inexpensive and disposable electrochemically controlled three-dimensional solid phase extraction materials. The composites, which had a total anion exchange capacity of about 1.1 mol kg⁻¹, were used for extraction and subsequent release of negatively charged fluorophore tagged DNA oligomers via galvanostatic oxidation and reduction of a 30–50 nm conformal PPy layer on the cellulose substrate. The ion exchange capacity, which was, at least, two orders of magnitude higher than those previously reached in electrochemically controlled extraction, originated from the high surface area (i.e. 80 m² g⁻¹) of the porous composites and the thin PPy layer which ensured excellent access to the ion exchange material. This enabled the extractions to be carried out faster and with better control of the PPy charge than with previously employed approaches. Experiments in equimolar mixtures of (dT)₆, (dT)₂₀, and (dT)₄₀ DNA oligomers showed that all oligomers could be extracted, and that the smallest oligomer was preferentially released with an efficiency of up to 40% during the reduction of the PPy layer. These results indicate that the present material is very promising for the development of inexpensive and efficient electrochemically controlled ion-exchange membranes for batch-wise extraction of biomolecules.

Toward flexible polymer and paper-based energy storage devices

All-polymer and paper-based energy storage devices have significant inherent advantages in comparison with many currently employed batteries and supercapacitors regarding environmental friendliness, flexibility, cost and versatility. The research within this field is currently undergoing an exciting development as new polymers, composites and paper-based devices are being developed. In this report, we review recent progress concerning the development of flexible energy storage devices based on electronically conducting polymers and cellulose containing composites with particular emphasis on paper-based batteries and supercapacitors. We discuss recent progress in the development of the most commonly used electronically conducting polymers used in flexible device prototypes, the advantages and disadvantages of this type of energy storage devices, as well as the two main approaches used in the manufacturing of paper-based charge storage devices.