XAFS, IR, and UV−Vis Study of the CuI Environment in CuI-ZSM-5

Selective Oxidative Dehydrogenation of Ethane and Propane over Copper-Containing Mordenite: Insights into Reaction Mechanism and Product Protection

Copper(II)-containing mordenite (CuMOR) is capable of activation of C-H bonds in C1 -C3 alkanes, albeit there are remarkable differences between the functionalization of ethane and propane compared to methane. The reaction of ethane and propane with CuMOR results in the formation of ethylene and propylene, while the reaction of methane predominantly yields methanol and dimethyl ether. By combining in situ FTIR and MAS NMR spectroscopies as well as time-resolved Cu K-edge X-ray absorption spectroscopy, the reaction mechanism was derived, which differs significantly for each alkane. The formation of ethylene and propylene proceeds via oxidative dehydrogenation of the corresponding alkanes with selectivity above 95 % for ethane and above 85 % for propane. The formation of stable π-complexes of olefins with CuI sites, formed upon reduction of CuII -oxo species, protects olefins from further oxidation and/or oligomerization. This is different from methane, the activation of which proceeds via oxidative hydroxylation leading to the formation of surface methoxy species bonded to the zeolite framework. Our findings constitute one of the major steps in the direct conversion of alkanes to important commodities and open a novel research direction aiming at the selective synthesis of olefins.

Understanding C-H activation in light alkanes over Cu-MOR zeolites by coupling advanced spectroscopy and temperature-programmed reduction experiments

The direct activation of methane to methanol (MTM) proceeds through a chemical-looping process over Cu-oxo sites in zeolites. Herein, we extend the overall understanding of oxidation reactions over metal-oxo sites and C-H activation reactions by pinpointing the evolution of Cu species during reduction. To do so, a set of temperature-programmed reduction experiments were performed with CH4, C2H6, and CO. With a temperature ramp, the Cu reduction could be accelerated to detect changes in Cu speciation that are normally not detected due to the slow CH4 adsorption/interaction during MTM (∼200 °C). To follow the Cu-speciation with the three reductants, X-ray absorption spectroscopy (XAS), UV-vis and FT-IR spectroscopy were applied. Multivariate curve resolution alternating least-square (MCR-ALS) analysis was used to resolve the time-dependent concentration profiles of pure Cu components in the X-ray absorption near edge structure (XANES) spectra. Within the large datasets, as many as six different CuII and CuI components were found. Close correlations were found between the XANES-derived CuII to CuI reduction, CH4 consumption, and CO2 production. A reducibility-activity relationship was also observed for the Cu-MOR zeolites. Extended X-ray absorption fine structure (EXAFS) spectra for the pure Cu components were furthermore obtained with MCR-ALS analysis. With wavelet transform (WT) analysis of the EXAFS spectra, we were able to resolve the atomic speciation at different radial distances from Cu (up to about 4 Å). These results indicate that all the CuII components consist of multimeric CuII-oxo sites, albeit with different Cu-Cu distances.

Cu+-Mediated CO Coordination for Promoting C-C Coupling for CO2 and CO Electroreduction

Selective electrochemical upgrading of CO₂ to multicarbon (C₂₊) products requires a C-C coupling process, yet the underlying promoting mechanism of widely involved Cu oxidation states remains largely unclear, hindering the subtle design of efficient catalysts. Herein, we unveil the critical role of Cu⁺ in promoting C-C coupling via coordination with a CO intermediate during electrochemical CO₂ reduction. We find that, relative to other halogen anions, iodide (I^-) in HCO₃^- electrolytes accelerates the generation of strongly oxidative hydroxyl radicals that accounts for the formation of Cu⁺, which can be dynamically stabilized by I^- via the formation of CuI. The in situ generated CO intermediate strongly binds to CuI sites, forming nonclassical Cu(CO)_n⁺ complexes, leading to an approximately 3.0-fold increase of C₂₊ Faradaic efficiency at -0.9 V_RHE relative to that of I^--free Cu surfaces. Accordingly, a deliberate introduction of CuI into I^--containing HCO₃^- electrolytes for direct CO electroreduction brings about a 4.3-fold higher C₂₊ selectivity. This work provides insights into the role of Cu⁺ in C-C coupling and the enhanced C₂₊ selectivity for CO₂ and CO electrochemical reduction.

Environmental Applications of Zeolites: Preparation and Screening of Cu-Modified Zeolites as Potential CO Sensors

This work is focused on the application of Cu-containing zeolites as potential environmental sensors for monitoring carbon monoxide. A number of commercial zeolites with different structural properties (NaX, NaY, MOR, FER, BEA and ZSM-5) were modified using CuSO4, Cu(NO3)2 and Cu(OAc)2 solutions as copper sources to prepare Cu+-containing zeolites, since Cu+ forms stable complexes with CO at room temperature that can be monitored by infrared spectroscopy. Zeolite impregnation with Cu(NO3)2 resulted in the highest total Cu-loadings, while the Cu(OAc)2-treated samples had the highest Cu+/Cutotal ratio. Cu(NO3)2-impregnated MOR, which displayed the highest concentration of Cu+, was subjected to a number of tests to evaluate its performance as a potential CO sensor. The working temperature and concentration ranges of the sensor were determined to be from 20 to 300 °C and from 10 to 10,000 ppm, respectively. The stepwise CO desorption experiments indicated that the sensor can be regenerated at 400 °C if required. Additional analyses under realistic flow conditions demonstrated that for hydrophilic zeolites, the co-adsorption of water can compromise the sensor’s performance. Therefore, a hydrophobic Sn-BEA was utilised as a parent material for the preparation of an impregnated Cu-Sn-BEA zeolite, which exhibited superior resistance to interfering water while maintaining its sensing properties. Overall, the prepared Cu-modified zeolites showed promising potential as environmental CO sensors, displaying high sensitivity and selectivity under representative testing conditions.

One Ca2+ Site in CaNaY Zeolite Can Attach Three CO2 Molecules

To design efficient CO₂ capture materials, it is necessary to ensure a high adsorption capacity. We recently reported that one Na⁺ site in NaY zeolite can attach two CO₂ molecules. However, the process is not suitable for practical use because it proceeds at a low temperature. Here, we present results on CO₂ adsorption on CaNaY zeolites, demonstrating that one Ca²⁺ site can attach three CO₂ molecules. The ν₃(¹³CO₂) mode arising from the natural ¹³C abundance allows for easy infrared monitoring of the processes: it appears at 2298, 2294, and 2291 cm^-1 for the complexes with one, two, and three CO₂ ligands, respectively. The ¹²CO₂ molecules in the polyligand complexes interact vibrationally, leading to the split of the ν₃(¹²CO₂) modes. At ambient temperature, Ca²⁺(CO₂)₂ complexes predominate at >1 mbar CO₂ and triligand species begin to form at 65 mbar. The obtained results show that CaY zeolites can be very effective CO₂ capture materials.

Leaching Stability and Redox Activity of Copper-MFI Zeolites Prepared by Solid-State Transformations: Comparison with Ion-Exchanged and Impregnated Samples

The catalyst preparation route is well known to affect the copper loading and its electronic state, which influence the properties of the resulting catalyst. Electronic states of copper ions in copper-containing silicalites with the MFI-framework topology obtained by a solid-state transformation S (SST) were studied with using EPR, UV-Vis DR, XRD, H₂-TPR and chemical differentiating dissolution. They were compared with Cu-ZSM-5 and Cu-MFI (silicalite) prepared via the ion-exchange and incipient wetness impregnation. SST route was shown to provide the formation of MFI structure and favor clustering of Cu-ions near surface and subsurface of zeolite crystals. The square-planar oxide clusters of Cu²⁺-ions and the finely dispersed CuO nanoparticles with the size down to 20 nm were revealed in Cu-MFI-SST samples with low (0.5-1.0 wt.%) and high (16 wt.%) Cu-content. The CuO nanoparticles were characterized by energy band gap 1-1.16 eV. The CuO-like clusters were characterized by ligand-to-metal charge transfer band (CTB L → M) at 32,000 cm^-1 and contain EPR-visible surface Cu²⁺-ions. The low Cu-loaded SST-samples had poor redox properties and activity towards different solvents due to decoration of copper-species by silica; whereas CuO nanoparticles were easily removed from the catalyst by HCl. In the ion-exchanged samples over MFI-silicalite and ZSM-5, Cu²⁺-ions were mainly CuO-like clusters and isolated Cu²⁺ ions inside MFI channels. Their redox properties and tendency to dissolve in acidic solutions differed from the behavior of SST-series samples.

A review on the characterization of metal active sites over Cu-based and Fe-based zeolites for NH3-SCR

Cu-based and Fe-based zeolites are promising catalysts for NH3-SCR due to their high catalytic activity, wide temperature window and good hydrothermal stability, while the detailed investigation of NH3-SCR mechanism should be based on the accurate determination of active metal sites. This review systematically summarizes the qualitative and quantitative determination of metal active sites in Cu-based or Fe-based zeolites for NH3-SCR reactions based on advanced characterization methods such as UV-vis absorption (UV-vis), temperature-programmed reduction with H2 (H2-TPR), X-ray photoelectron spectroscopy (XPS), X-ray absorption fine structure spectroscopy (XAFS), Infrared spectroscopy (IR), Electron paramagnetic resonance (EPR), Mössbauer spectroscopy and DFT calculations. The application and limitations of different characterization methods are also discussed to provide insights for further study of the NH3-SCR reaction mechanism over metal-based zeolites.

Titration of Cu(I) Sites in Cu-ZSM-5 by Volumetric CO Adsorption

Cu-exchanged zeolites are widely studied materials because of their importance in industrial energetic and environmental processes. Cu redox speciation lies at the center of many of these processes but is experimentally difficult to investigate in a quantitative manner with regular laboratory equipment. This work presents a novel technique for this purpose that exploits the selective adsorption of CO over accessible Cu(I) sites to quantify them. In particular, isothermal volumetric adsorption measurements are performed at 50 °C on a series of opportunely pre-reduced Cu-ZSM-5 to assess the relative fraction of Cu(I); the setup is fairly simple and only requires a regular volumetric adsorption apparatus to perform the actual measurement. Repeatability tests are carried out on the measurement and activation protocols to assess the precision of the technique, and the relative standard deviation (RSD) obtained is less than 5%. Based on the results obtained for these materials, the same CO adsorption protocol is studied for the sample using infrared spectroscopy, and a good correlation is found between the results of the volumetric measurements and the absorbance of the peak assigned to the Cu(I)-CO adducts. A linear model is built for this correlation, and the molar attenuation coefficient is obtained, allowing for spectrophotometric quantification. The good sensitivity of the spectrophotometric approach and the precision and simplicity of the volumetric approach form a complementary set of tools to quantitatively study Cu redox speciation in these materials at the laboratory scale, allowing for a wide range of Cu compositions to be accurately investigated.

Synthesis of indeno-[1,2-b]-quinoline-9,11(6H,10H)-dione and 7,7-dimethyl-10-aryl-7,8-dihydro-5H-indeno[1,2-b]quinoline-9,11(6H,10H)-dione derivatives in presence of heterogeneous Cu/zeolite-Y as a catalyst

A simple method for the synthesis of indeno-[1,2-b]-quinoline-9,11-(6H,10H)-dione derivatives and 7,7-dimethyl-10-aryl-7,8-dihydro-5H-indeno[1,2-b]quinoline-9,11(6H,10H)-diones through the reaction of aromatic aldehydes, indan-1,3-dione, dimedone, and p-toluidine/ammonium acetate in the presence of heterogeneous CuO supported on a zeolite-Y catalyst has been investigated in ethanol under reflux conditions. By this method, the reaction time has been reduced, giving an excellent yield of the product. The catalyst was prepared by a hydrothermal method followed by a wet impregnation method. The catalyst had shown Brønsted acid sites and Lewis acid sites. The used catalyst could be actively recycled with a marginal decrease in yield up to five recycles. The prepared catalyst was characterized by FT-IR, pyridine FT-IR, XRD, SEM, EDS, XPS, TEM, and BET surface area analysis. The synthesized compounds were characterized by FT-IR, 1H NMR, 13C NMR and GC-MS spectroscopy.

Hybrid Cu-Fe/ZSM-5 Catalyst Prepared by Liquid Ion-Exchange for NOx Removal by NH3-SCR Process

A series of Cu/ZSM-5, Fe/ZSM-5, and Cu-Fe/ZSM-5 catalysts (Si/Al in ZSM-5 = 25) were prepared by different metal loadings using the liquid ion-exchange method. Several characterization methods were conducted to explore the effects of metals on the physical and chemical properties of catalysts. Meanwhile, the electron paramagnetic resonance method is also used to assess the copper and/or iron elements’ coordination and valence state at intersections or in channels of ZSM-5. The metal-loading effects of all catalysts on the catalytic activities were studied for the removal of NOx in a fixed-bed flow reactor using selective catalytic reduction with ammonia (NH3-SCR). The results showed that the iron’s addition could markedly broaden the operation temperature range of the Cu/ZSM-5 catalyst for NH3-SCR between 200 and 550°C due to the presence of more isolated Cu2+ ions as well as additional oligomeric Fe3+ active sites and FexOy oligomeric species. This paper gives a facile and straightforward way to synthesize the practical-promising catalyst applied in NH3-SCR technology to control NOx emissions.

Oxidation of Ethanol in Cu-Faujasites Studied by IR Spectroscopy

In this study, IR studies of the coadsorption of ethanol and CO on Cu⁺ cations evidenced the transfer of electrons from ethanol to Cu⁺, which caused the lowering of the frequency of the band attributed to CO bonded to the same Cu⁺ cation due to the more effective π back donation of d electrons of Cu to antibonding π* orbitals of CO. The reaction of ethanol with acid sites in zeolite HFAU above 370 K produced water and ethane, polymerizing to polyethylene. Ethanol adsorbed on zeolite Cu(2)HFAU containing acid sites and Cu⁺_exch also produced ethene, but in this case, the ethene was bonded to Cu⁺ and did not polymerize. C=C stretching, which is IR non-active in the free ethene molecule, became IR active, and a weak IR band at 1538 cm^-1 was present. The reaction of ethanol above 370 K in Cu(5)NaFAU zeolite (containing small amounts of Cu⁺_exch and bigger amounts of Cu⁺_ox, Cu²⁺_exch and CuO) produced acetaldehyde, which was further oxidized to the acetate species (CH₃COO^-). As oxygen was not supplied, the donors of oxygen were the Cu species present in our zeolite. The CO and NO adsorption experiments performed in Cu-zeolite before and after ethanol reaction evidenced that both Cu⁺_ox and Cu²⁺ (Cu²⁺_exch and CuO) were consumed by the ethanol oxidation reaction. The studies of the considered reaction of bulk CuO and Cu₂O as well as zeolites, in which the contribution of Cu⁺_ox species was reduced by various treatments, suggest that ethanol was oxidized to acetaldehyde by Cu²⁺_ox (the role of Cu⁺_ox could not be elucidated), but Cu⁺_ox was the oxygen donor in the acetate formation.

On the Role of Protonic Acid Sites in Cu Loaded FAU31 Zeolite as a Catalyst for the Catalytic Transformation of Furfural to Furan

The aim of the present paper is to study the speciation and the role of different active site types (copper species and Brønsted acid sites) in the direct synthesis of furan from furfural catalyzed by copper-exchanged FAU31 zeolite. Four series of samples were prepared by using different conditions of post-synthesis treatment, which exhibit none, one or two types of active sites. The catalysts were characterized by XRD, low-temperature sorption of nitrogen, SEM, H₂-TPR, NMR and by means of IR spectroscopy with ammonia and CO sorption as probe molecules to assess the types of active sites. All catalyst underwent catalytic tests. The performed experiments allowed to propose the relation between the kind of active centers (Cu or Brønsted acid sites) and the type of detected products (2-metylfuran and furan) obtained in the studied reaction. It was found that the production of 2-methylfuran (in trace amounts) is determined by the presence of the redox-type centers, while the protonic acid sites are mainly responsible for the furan production and catalytic activity in the whole temperature range. All studied catalysts revealed very high susceptibility to coking due to polymerization of furfural.

Influence of Alumina Precursor Properties on Cu-Fe Alumina Supported Catalysts for Total Toluene Oxidation as a Model Volatile Organic Air Pollutant

The structure–property relationship of catalytic supports for the deposition of redox-active transition metals is of great importance for improving the catalytic efficiency and reusability of the catalysts. In this work, the role of alumina support precursors of Cu-Fe/Al2O3 catalysts used for the total oxidation of toluene as a model volatile organic air pollutant is elucidated. Surface characterization of the catalysts revealed that the surface area, pore volume and acid site concentration of the alumina supports are important but not the determining factors for the catalytic activity of the studied catalysts for this type of reaction. The determining factors are the structural order of the support precursor, the homogeneous distribution of the catalytic sites and reducibility, which were elucidated by XRD, NMR, TEM and temperature programed reduction (TPR). Cu–Fe/Al2O3 prepared from bayerite and pseudoboehmite as highly ordered precursors showed better catalytic performance compared to Cu-Fe/Al2O3 derived from the amorphous alumina precursor and dawsonite. Homogeneous distribution of FexOy and CuOx with defined Cu/Fe molar ratio on the Al2O3 support is required for the efficient catalytic performance of the material. The study showed a beneficial effect of low iron concentration introduced into the alumina precursor during the alumina support synthesis procedure, which resulted in a homogeneous metal oxide distribution on the support.

Methanol reforming denitration over an integrated bifunctional CuZnOx–X–MnPdOz@Ni catalyst at low temperature

Severe conditions involved in hydrogen storage and transportation limit the practical applications of hydrogen denitration reaction.

Cu- and Fe-speciation in a composite zeolite catalyst for selective catalytic reduction of NOx: insights from operando XAS

Cu-SAPO-34 (Cu-CZC) and Fe-mordenite (Fe-MOR) and their mechanical mixture (50 : 50) have been exhaustively investigated by means of operando X-ray absorption spectroscopy under NH₃-SCR conditions.

DFT Study on Mechanisms of the N2O Direct Catalytic Decomposition over Cu-ZSM-5: The Detailed Investigation on NO Formation Mechanism

Nitrous oxide (N2O) is an industrial emission that causes the greenhouse effect and damages the ozone layer. Density functional theory study on the N2O direct catalytic decomposition over Cu–ZSM-5 has been performed in this paper. Two possible reaction mechanisms for N2O direct catalytic decomposition over Cu-ZSM-5 were proposed (O2 formation mechanism and Nitric oxide (NO) formation mechanism). The geometrical parameters, vibration frequency and thermodynamic data of the intermediate states in each step have been examined. The results indicate that N2O can be adsorbed on active site Cu in two ways (O-terminal or N-terminal), and N2O decomposition reactions can occur in both cases. The NO formation mechanism exhibits higher N2O dissociation reaction due to lower energy barrier.

Active sites and mechanisms in the direct conversion of methane to methanol using Cu in zeolitic hosts: a critical examination

In this critical review we examine the current state of our knowledge in respect of the nature of the active sites in copper containing zeolites for the selective conversion of methane to methanol.

Cu oxo nanoclusters for direct oxidation of methane to methanol: formation, structure and catalytic performance

Cu oxo nanoclusters hosted in microporous solids have emerged in the past decades as promising materials for catalyzing the selective conversion of methane to methanol.

Temperature-dependent dynamics of NH3-derived Cu species in the Cu-CHA SCR catalyst

In situ XAS and UV-vis–NIR spectroscopy shed light on Cu-speciation during NH₃ temperature-programmed desorption and surface reaction (TPSR) over a commercial Cu-chabazite deNO_x catalyst, expanding the fundamental knowledge required to unravel the NH₃-SCR mechanism across the whole operation-relevant temperature range.

Copper-Modified Zeolites and Silica for Conversion of Methane to Methanol

Powder materials containing copper ions supported on ZSM-5 (Cu-Zeolite Socony Mobil-5) and SSZ-13 (Cu-Standard Oil synthesised zeolite-13), and predominantly CuO nanoparticles on amorphous SiO 2 were synthesised, characterised, wash-coated onto ceramic monoliths and, for the first time, compared as catalysts for direct conversion of methane to methanol (DCMM) at ambient pressure (1 atm) using O 2 , N 2 O and NO as oxidants. Methanol production was monitored and quantified using Fourier transform infrared spectroscopy. Methanol is formed over all monolith samples, though the formation is considerably higher for the copper-exchanged zeolites. Hence, copper ions are the main active sites for DCMM. The minor amount of methanol produced over the Cu/SiO 2 sample, however, suggests that zeolites are not the sole substrate that can host those active copper sites but also silica. Further, we present the first ambient pressure in situ infrared spectroscopic measurements revealing the formation and consumption of surface methoxy species, which are considered to be key intermediates in the DCMM reaction.

The promotion effect of manganese on Cu/SAPO for selective catalytic reduction of NO x with NH3

The activity and hydrothermal stability of Cu/SAPO and xMn–2Cu/SAPO for low-temperature selective catalytic reduction of NO_x with ammonia were investigated. An ion-exchanged method was employed to synthesize xMn–2Cu/SAPO, which was characterized by N₂ adsorption, ICP-AES, X-ray diffraction (XRD), NH₃-temperature programmed desorption (NH₃-TPD), NO oxidation, X-ray photoelectron spectrum (XPS), UV-vis, H₂-temperature programmed reduction (H₂-TPR) and diffuse reflectance infrared Fourier transform spectra (DRIFTS). 2Mn–2Cu/SAPO and 4Mn–2Cu/SAPO showed the best SCR activity, in that at 150 °C NO conversion reached 76% and N₂ selectivity was above 95% for the samples. NO oxidation results showed that the 2Mn–2Cu/SAPO had the best NO oxidation activity and the BET surface area decreased as manganese loading increased. XRD results showed that the metal species was well dispersed. NH₃-TPD showed that the acid sites have no significant influence on the SCR activity of xMn–2Cu/SAPO. H₂-TPR patterns showed good redox capacity for xMn–2Cu/SAPO. UV-vis and H₂-TPR showed that the ratio of Mn⁴⁺ to Mn³⁺ increased as manganese loading increased. XPS spectra showed a significant amount of Mn³⁺ and Mn⁴⁺ species on the surface and addition of manganese increased the ratio of Cu²⁺. The promotion effect of manganese to 2Cu/SAPO comes from the generation of Mn³⁺ and Mn⁴⁺ species. Deduced from the DRIFTS spectra, the Elay–Rideal mechanism was effective on 4Mn–2Cu/SAPO.

The activity and N₂ selectivity of Cu/SAPO and xMn–2Cu/SAPO for low-temperature selective catalytic reduction of NO_x with NH₃ were investigated.

Cu-CHA – a model system for applied selective redox catalysis

We review the structural chemistry and reactivity of copper-exchanged molecular sieves with chabazite (CHA) topology, as an industrially applied catalyst in ammonia mediated reduction of harmful nitrogen oxides (NH₃-SCR) and as a general model system for red-ox active materials (also the recent results in the direct conversion of methane to methanol are considered).

Composition-driven Cu-speciation and reducibility in Cu-CHA zeolite catalysts: a multivariate XAS/FTIR approach to complexity

The small pore Cu-CHA zeolite is attracting increasing attention as a versatile platform to design novel single-site catalysts for deNO _x applications and for the direct conversion of methane to methanol. Understanding at the atomic scale how the catalyst composition influences the Cu-species formed during thermal activation is a key step to unveil the relevant composition-activity relationships. Herein, we explore by in situ XAS the impact of Cu-CHA catalyst composition on temperature-dependent Cu-speciation and reducibility. Advanced multivariate analysis of in situ XANES in combination with DFT-assisted simulation of XANES spectra and multi-component EXAFS fits as well as in situ FTIR spectroscopy of adsorbed N₂ allow us to obtain unprecedented quantitative structural information on the complex dynamics during the speciation of Cu-sites inside the framework of the CHA zeolite.

Mn/SAPO-34 as an efficient catalyst for the low-temperature selective catalytic reduction of NOx with NH3

A series of Mn-exchanged SAPO-34 catalysts were synthesized and developed as catalysts for the low temperature selective catalytic reduction (SCR) of NO with ammonia in the presence of excess oxygen.

Nitrate–nitrite equilibrium in the reaction of NO with a Cu-CHA catalyst for NH3-SCR

A multi-technique in situ study of the reaction between NO and Cu-nitrates in the Cu-CHA deNO_x catalyst yields novel structural and spectroscopic insights into the equilibrium between Cu-nitrates and Cu-nitrites, which was proposed as key step in the NH₃-SCR cycle.

Methane to methanol over copper mordenite: yield improvement through multiple cycles and different synthesis techniques

Successive cycles over Cu-mordenite for the conversion of methane to methanol provided higher yields.

Probing zeolites by vibrational spectroscopies

This review addresses the most relevant aspects of vibrational spectroscopies (IR, Raman and INS) applied to zeolites and zeotype materials. Surface Brønsted and Lewis acidity and surface basicity are treated in detail. The role of probe molecules and the relevance of tuning both the proton affinity and the steric hindrance of the probe to fully understand and map the complex site population present inside microporous materials are critically discussed. A detailed description of the methods needed to precisely determine the IR absorption coefficients is given, making IR a quantitative technique. The thermodynamic parameters of the adsorption process that can be extracted from a variable-temperature IR study are described. Finally, cutting-edge space- and time-resolved experiments are reviewed. All aspects are discussed by reporting relevant examples. When available, the theoretical literature related to the reviewed experimental results is reported to support the interpretation of the vibrational spectra on an atomic level.

Flexible bonding between copper and nitric oxide: infrared photodissociation spectroscopy of copper nitrosyl cation complexes: [Cu(NO)n]+ (n = 1-5)

The infrared spectra of mass-selected mononuclear copper nitrosyl cation complexes [Cu(NO)n](+) with n = 1-5 and their argon tagged complexes are measured via infrared photodissociation spectroscopy in the nitrosyl stretching frequency region in the gas phase. The experimental spectra provide distinctive patterns allowing the determination of the geometries and electronic structures of these complexes by comparison with the predicted spectra from density functional theory computations. The argon tagged [Cu(NO)2Ar2](+) and [Cu(NO)3Ar](+) complexes as well as the higher n = 4 and 5 complexes each involve a bidentate (NO)2 dimer ligand, suggesting that ligand-ligand coupling plays an important role in the bonding of these cation systems. The results also show that argon tagging has a strong influence on the geometric and electronic structures of the n = 2 and 3 complexes. The [Cu(NO)4](+) cation is the most intense peak in the mass spectrum, which is characterized to be the fully coordinated ion with a D2d structure involving two (NO)2 units but with only 14-valence electrons on Cu. The [Cu(NO)5](+) cation complex is determined to involve a [Cu(NO)4](+) core ion that is coordinated by an external NO ligand.

Recent advances in dialkyl carbonates synthesis and applications

Dialkyl carbonates are important organic compounds and chemical intermediates with the label of "green chemicals" due to their moderate toxicity, biodegradability for human health and environment. Indeed, owing to their unique physicochemical properties and versatility as reagents, a variety of phosgene-free processes derived from CO or CO2 have been explored for the synthesis of dialkyl carbonates. In this critical review, we highlight the recent achievements (since 1997) in the synthesis of dialkyl carbonates based on CO and CO2 utilization, particularly focusing on the catalyst design and fabrication, structure-function relationship, catalytic mechanisms and process intensification. We also provide an overview regarding the applications of dialkyl carbonates as fuel additives, solvents and reaction intermediates (i.e. alkylating and carbonylating agents). Additionally, this review puts forward the substantial challenges and opportunities for future research associated with dialkyl carbonates.