Surface immobilized protein multilayers for cell seeding

In Vitro Evaluation of PCL and P(3HB) as Coating Materials for Selective Laser Melted Porous Titanium Implants

Titanium is widely used as a bone implant material due to its biocompatibility and high resilience. Since its Young’s modulus differs from bone tissue, the resulting “stress shielding” could lead to scaffold loosening. However, by using a scaffold-shaped geometry, the Young’s modulus can be adjusted. Also, a porous geometry enables vascularisation and bone ingrowth inside the implant itself. Additionally, growth factors can improve these effects. In order to create a deposit and release system for these factors, the titanium scaffolds could be coated with degradable polymers. Therefore, in the present study, synthetic poly-ε-caprolactone (PCL) and the biopolymer poly(3-hydroxybutyrate) (P(3HB)) were tested for coating efficiency, cell adhesion, and biocompatibility to find a suitable coating material. The underlying scaffold was created from titanium by Selective Laser Melting (SLM) and coated with PCL or P(3HB) via dip coating. To test the biocompatibility, Live Cell Imaging (LCI) as well as vitality and proliferation assays were performed. In addition, cell adhesion forces were detected via Single Cell Force Spectroscopy, while the coating efficiency was observed using environmental scanning electron microscopy (ESEM) and energy-dispersive X-ray (EDX) analyses. Regarding the coating efficiency, PCL showed higher values in comparison to P(3HB). Vitality assays revealed decent vitality values for both polymers, while values for PCL were significantly lower than those for blank titanium. No significant differences could be observed between PCL and P(3HB) in proliferation and cell adhesion studies. Although LCI observations revealed decreasing values in cell number and populated area over time on both polymer-coated scaffolds, these outcomes could be explained by the possibility of coating diluent residues accumulating in the culture medium. Overall, both polymers fulfill the requirements regarding biocompatibility. Nonetheless, since only PCL coating ensured the maintenance of the porous implant structure, it is preferable to be used as a coating material for creating a deposit and release system for growth factors.

Biomimetic Extracellular Environment Based on Natural Origin Polyelectrolyte Multilayers

Surface modification of biomaterials is a well-known approach to enable an adequate biointerface between the implant and the surrounding tissue, dictating the initial acceptance or rejection of the implantable device. Since its discovery in early 1990s layer-by-layer (LbL) approaches have become a popular and attractive technique to functionalize the biomaterials surface and also engineering various types of objects such as capsules, hollow tubes, and freestanding membranes in a controllable and versatile manner. Such versatility enables the incorporation of different nanostructured building blocks, including natural biopolymers, which appear as promising biomimetic multilayered systems due to their similarity to human tissues. In this review, the potential of natural origin polymer-based multilayers is highlighted in hopes of a better understanding of the mechanisms behind its use as building blocks of LbL assembly. A deep overview on the recent progresses achieved in the design, fabrication, and applications of natural origin multilayered films is provided. Such films may lead to novel biomimetic approaches for various biomedical applications, such as tissue engineering, regenerative medicine, implantable devices, cell-based biosensors, diagnostic systems, and basic cell biology.

SLM produced porous titanium implant improvements for enhanced vascularization and osteoblast seeding

To improve well-known titanium implants, pores can be used for increasing bone formation and close bone-implant interface. Selective Laser Melting (SLM) enables the production of any geometry and was used for implant production with 250-µm pore size. The used pore size supports vessel ingrowth, as bone formation is strongly dependent on fast vascularization. Additionally, proangiogenic factors promote implant vascularization. To functionalize the titanium with proangiogenic factors, polycaprolactone (PCL) coating can be used. The following proangiogenic factors were examined: vascular endothelial growth factor (VEGF), high mobility group box 1 (HMGB1) and chemokine (C-X-C motif) ligand 12 (CXCL12). As different surfaces lead to different cell reactions, titanium and PCL coating were compared. The growing into the porous titanium structure of primary osteoblasts was examined by cross sections. Primary osteoblasts seeded on the different surfaces were compared using Live Cell Imaging (LCI). Cross sections showed cells had proliferated, but not migrated after seven days. Although the cell count was lower on titanium PCL implants in LCI, the cell count and cell spreading area development showed promising results for titanium PCL implants. HMGB1 showed the highest migration capacity for stimulating the endothelial cell line. Future perspective would be the incorporation of HMGB1 into PCL polymer for the realization of a slow factor release.

Conducting polyaniline based cell culture substrate for embryonic stem cells and embryoid bodies

Noncytotoxic polyaniline–poly(2-acrylamido-2-methyl-1-propanesulfonate) films which are electrically conducting at the physiological pH were applied as cell culture substrate. The films demonstrate selective interaction with specific target cells.

The gene expression of human endothelial cells is modulated by subendothelial extracellular matrix proteins: short-term response to laminar shear stress

Vascular surgery for atherosclerosis is confronted by the lack of a suitable bypass material. Tissue engineering strives to produce bio-artificial conduits to provide resistance to thrombosis. The objectives of our study were to culture endothelial cells (EC) on composite assemblies of extracellular matrix proteins, and to evaluate the cellular phenotype under flow. Cell-adhesive assemblies were fabricated on glass slides as combinations of collagen (Co), laminin (LM), and fibronectin (FN), resulting in three samples: Co, Co/LM, and Co/FN. Surface topography, roughness, and wettability were determined. Human saphenous vein EC were harvested from cardiac patients, cultured on the assemblies and submitted to laminar shear stress (SS) of 12 dyn/cm(2) for 40, 80, and 120 min. Cell retention was assessed and qRT-PCR of adhesion genes (VE-cadherin, vinculin, KDR, CD-31 or PECAM-1, β1-integrins) and metabolic genes (t-PA, NF-κB, eNOS and MMP-1) was performed. Quantitative immunofluorescence of VE cadherin, vinculin, KDR, and vonWillebrand factor was performed after 2 and 6 h of flow. Static samples were excluded from shearing. The cells reached confluence with similar growth curves. The cells on Co/LM and Co/FN were resistant to flow up to 120 min but minor desquamation occurred on Co corresponding with temporary downregulation of VE cadherin and vinculin-mRNA and decreased fluorescence of vinculin. The cells seeded on Co/LM initially more upregulated vinculin-mRNA and also the inflammatory factor NF-κB, and the cells plated on Co/FN changed the expression profile minimally in comparison with the static control. Fluorescence of VE cadherin and vonWillebrand factor was enhanced on Co/FN. The cells cultured on Co/LM and Co/FN increased the vinculin fluorescence and expressed more VE cadherin and KDR-mRNA than the cells on Co. The cells plated on Co/FN upregulated the mRNA of VE cadherin, CD-31, and MMP 1 to a greater extent than the cells on Co/LM and they enhanced the fluorescence of VE cadherin, KDR, and vonWillebrand factor. Some of these changes sustained up to 6 h of flow, as confirmed by immunofluorescence. Combined matrices Co/LM and Co/FN seem to be more suitable for EC seeding and retention under flow. Moreover, Co/FN matrix promoted slightly more favorable cellular phenotype than Co/LM under SS of 2-6 h.

Cell adhesion as a novel approach to determining the cellular binding motif on the severe acute respiratory syndrome coronavirus spike protein

Emerging life threatening pathogens such as severe acute aspiratory syndrome-coronavirus (SARS-CoV), avian-origin influenzas H7N9, and the Middle East respiratory syndrome coronavirus (MERS-CoV) have caused a high case-fatality rate and psychological effects on society and the economy. Therefore, a simple, rapid, and safe method to investigate a therapeutic approach against these pathogens is required. In this study, a simple, quick, and safe cell adhesion inhibition assay was developed to determine the potential cellular binding site on the SARS-CoV spike protein. Various synthetic peptides covering the potential binding site helped to minimize further the binding motif to 10–25 residues. Following analyses, 2 peptides spanning the 436–445 and 437–461 amino acids of the spike protein were identified as peptide inhibitor or peptide vaccine candidates against SARS-CoV.

Surface modification of poly(propylene carbonate) by layer-by-layer assembly and its hemocompatibility

Heparin and lysozyme were used to immobilize onto surface of poly(propylene carbonate) by layer-by-layer assembly to improve hemocompatibility.

Organic silicone sol-gel polymer as a noncovalent carrier of receptor proteins for label-free optical biosensor application

Optical biosensing techniques have become of key importance for label-free monitoring of biomolecular interactions in the current proteomics era. Together with an increasing emphasis on high-throughput applications in functional proteomics and drug discovery, there has been demand for facile and generally applicable methods for the immobilization of a wide range of receptor proteins. Here, we developed a polymer platform for microring resonator biosensors, which allows the immobilization of receptor proteins on the surface of waveguide directly without any additional modification. A sol-gel process based on a mixture of three precursors was employed to prepare a liquid hybrid polysiloxane, which was photopatternable for the photocuring process and UV imprint. Waveguide films were prepared on silicon substrates by spin coating and characterized by atomic force microscopy for roughness, and protein adsorption. The results showed that the surface of the polymer film was smooth (rms = 0.658 nm), and exhibited a moderate hydrophobicity with the water contact angle of 97°. Such a hydrophobic extent could provide a necessary binding strength for stable immobilization of proteins on the material surface in various sensing conditions. Biological activity of the immobilized Staphylococcal protein A and its corresponding biosensing performance were demonstrated by its specific recognition of human Immunoglobulin G. This study showed the potential of preparing dense, homogeneous, specific, and stable biosensing surfaces by immobilizing receptor proteins on polymer-based optical devices through the direct physical adsorption method. We expect that such polymer waveguide could be of special interest in developing low-cost and robust optical biosensing platform for multidimensional arrays.

Adhesion, Growth and Differentiation of Osteoblasts on Surface-Modified Materials Developed for Bone Implants

This review briefly outlines the history and possibilities of bone reconstruction using various types of artificial materials, which allow interaction with cells only on the surface of the implant or enable ingrowth of cells inside the material. Information is also provided on the most important properties of bone cells taking part in bone tissue development, and on diseases and regeneration. The most common cell types used for testing cell-material interaction in vitro are listed, and the most commonly used approaches to this testing are also mentioned. A considerable part of this review is dedicated to the physical and chemical properties of the material surface, which are decisive for the cell-material interaction, and also to modifications to the surface of the material aimed at integrating it better with the surrounding bone tissue. Special attention is paid to the effects of nanoscale and microscale surface roughness on cell behaviour, to material surface patterning, which allows regionally-selective adhesion and growth of cells, and also to the surface chemistry. In addition, coating the materials with bioactive layers is examined, particularly those created by deposition of fullerenes, hybrid metal-fullerene composites, carbon nanotubes, nanocrystalline diamond films, diamond-like carbon, and nanocomposite hydrocarbon plasma polymer films enriched with metals.

The role of smooth muscle cells in vessel wall pathophysiology and reconstruction using bioactive synthetic polymers

This review summarizes recent trends in the construction of bioartificial vascular replacements, i.e. hybrid grafts containing synthetic polymeric scaffolds and cells. In these advanced replacements, vascular smooth muscle cells (VSMC) should be considered as a physiological component, although it is known that activation of the migration and proliferation of VSMC plays an important role in the onset and development of vascular diseases, and also in restenosis of currently used vascular grafts. Therefore, in novel bioartificial vascular grafts, VSMCs should be kept in quiescent mature contractile phenotype. This can be achieved by (1) appropriate physical and chemical properties of the material, such as its chemical composition, polarity, wettability, surface roughness and topography, electrical charge and conductivity, functionalization with biomolecules and mechanical properties, (2) appropriate cell culture conditions, such as composition of cell culture media and dynamic load, namely cyclic strain, and (3) the presence of a confluent, mature, semipermeable, non-thrombogenic and non-immunogenic endothelial cell (EC) barrier, covering the luminal surface of the graft and separating the VSMCs from the blood. Both VSMCs and ECs can also be differentiated from stem and progenitor cells of various sources. In the case of degradable scaffolds, the material will gradually be removed by the cells and will be replaced by their own new extracellular matrix. Thus, the material component in advanced blood vessel substitutes acts as a temporary scaffold that promotes regeneration of the damaged vascular tissue.

Crosslink effect and albumin adsorption onto chitosan/alginate multilayered systems: an in situ QCM-D study

The adsorption of HSA onto CHI/ALG multilayer assemblies was assessed in situ using QCM-D. It was found that the behavior of HSA on biomaterials surface can be tuned by adjusting parameters of the polyelectrolyte system such as pH, layer number, crosslinker and polymer terminal layer. Our results confirmed the key role of electrostatic interactions during HSA adsorption, since oppositely charged surfaces were more effective in promoting protein adhesion. QCM-D data revealed that crosslinking (CHI/ALG)(5) CHI films allows HSA to become adsorbed in physiological conditions. Our results suggested that the biological potential of biopolymers and the mild conditions of the LbL technique turn these natural nanoassemblies into a suitable choice to be used as pH-sensitive coatings.

Control of cell surface and functions by layer-by-layer nanofilms

Various nanometer-sized multilayers were directly prepared onto the surface of mouse L929 fibroblast cells by a layer-by-layer (LbL) assembly technique to control the cell surface microenvironment and cell functions, such as viability, morphology, and proliferation. The species of LbL nanofilms strongly affected the cell morphology and growth. Polyelectrolyte (PE) multilayers induced a round-shaped morphology of the adhered cells, although each component of the multilayers had high cytocompatibility, whereas fibronectin (FN)-gelatin (G) and -dextran sulfate (DS) multilayers with FN-binding domain interactions (FN films) showed extended morphologies of the cells similar to that of control cells (without films). A clear difference in cell proliferation was observed for PE and FN films. The cells with FN films on their surfaces showed good proliferation profiles independent of the film thickness, but cell proliferation was not observed using the PE films although the cells survived during the culture period. Fluorescence microscopic and scanning electron microscopic observations clearly suggested a nanometer-sized meshwork morphology of the FN films on the cell surface after 24 h of incubation, whereas the PE films showed homogeneous film morphologies on the cell surface. These nanomeshwork morphologies seemed to be similar to the fibrous structure of the natural extracellular matrix. The results of this study demonstrated that the components, charge, and morphology of LbL nanofilms prepared directly on the cell surface strongly affected cell functions, and the effects of these LbL nanofilms on cell functions differed vastly as compared to PE films prepared on a substrate. The preparation of LbL nanofilms onto a cell surface might be a novel and interesting technique to control cell functions.

Modeling the buildup of exponentially growing polyelectrolyte multilayer films

We develop a simplified one-dimensional model to describe the build-up of exponentially growing polyelectrolyte multilayer films. The model accounts for the migration of polycations in and out of the film, the existence of an energetic barrier at the film surface, and film dissolution. All the electrostatic interactions are modeled using a screened Coulombic potential. For appropriately chosen model parameters, the model predictions are in quantitative agreement with experimental results. The model predicts that the exponential-to-linear growth transition is set kinetically, and this transition occurs when the dipping time is not long enough for unbound polycations to uniformly distribute inside the film. Additionally, for a film to exhibit exponential growth, it is essential that very few unbound polycations move out of the film during the rinsing step that follows after dipping in a solution of polycations. The model predicts that this criterion is satisfied either when a sharply peaked energetic barrier is present at the film surface or when the film swells. Furthermore, the model predicts that when dipping time, t(d), is increased proportionally with H(2), where H is the film thickness, the film will grow exponentially as long as k(d)t(d) << 1, where k(d) is the dissolution rate. The results of this work shed light on the criteria that need to be satisfied for a film to grow exponentially, and could help in exercising better control over the thickness of polyelectrolyte multilayer films.

Surface modification of hydrogels based on poly(2-hydroxyethyl methacrylate) with extracellular matrix proteins

Infrared attenuated total reflection spectroscopy was used for in situ observation of the deposition of collagen I on poly(2-hydroxyethyl methacrylate-co-methacrylic acid, 2.9%) hydrogels and subsequent attachment of laminin or fibronectin on the collagen surface. While there was no adsorption of collagen dissolved in an acid solution on the hydrogel surface, it deposited on the surface at pH 6.5. The collagen layers with attached laminin or fibronectin were stable on hydrogel surface in physiological solution. The modification with collagen and particularly with collagen and laminin or fibronectin allowed the adhesion and growth of mesenchymal stromal cells and astrocytes on the hydrogel surface.

Covalently linked DNA/protein multilayered film for controlled DNA release

A stable, biocompatible single strand DNA (ssDNA)/bovine serum albumin (BSA) multilayered film for control release of DNA was fabricated on PEI-coated quartz slides, gold-evaporated plates and silicon wafers, respectively through a formaldehyde-induced, covalently linked layer-by-layer (LBL) assembly technique. The constructed film structure was well characterized by using UV-vis spectrometry, surface plasmon resonance (SPR) and atomic force microscopy (AFM). The results showed that the DNA incorporated LBL film was fabricated successfully and the amount of ssDNA and BSA in the film could be tailored simply by controlling the number of the bilayers. The control release of DNA from the film was also monitored in this study. UV-vis spectrometry, SPR and AFM measurements indicated that the release of ssDNA and amino acid was adjustable by changing the proteinase K incubation time. This biocompatible covalently assembled film demonstrates an innovative approach to engineer a DNA/protein based nanostructure for controlled DNA release, which could provide stability, controllability and flexibility superior to that of LBL film assembled by electrostatic attraction. Since the film in this work can be assembled on different substrates, it is very feasible to fabricate nanoparticle-based gene therapy systems with this new approach and to have great potential in biomedical applications.

Application of microarrays to identify and characterize genes involved in attachment dependence in HeLa cells

The ability to modify cellular properties such as adhesion is of interest in the design and performance of biotechnology-related processes. The current study was undertaken in order to evaluate the effectiveness of modulating cellular adhesion in HeLa cells from a genomics perspective. Using DNA microarrays, differences in gene expression between two phenotypically distinct, anchorage-dependent and anchorage-independent, HeLa cell lines were identified. With the aid of several statistical methods and an extensive literature search, two genes were selected as potential targets for further study: siat7e and lama4. Subsequently, experiments were carried out to investigate the effects of siat7e and lama4 separately, on adhesion in HeLa cells by altering their expression in vivo. Decreasing the expression of siat7e, a type II membrane glycosylating sialyltransferase, in anchorage-independent HeLa cells using short interfering RNA (siRNA) resulted in greater aggregation (i.e. clumping) and morphological changes as compared to untreated anchorage-independent HeLa cells. Similar effects were seen in anchorage-independent HeLa cells when the expression of lama4 which encodes laminin alpha4, a member of the laminin family of glycoproteins, was enhanced as compared to untreated anchorage-independent HeLa cells. Using a shear flow chamber, an attachment assay was developed; illustrating either increased expression of siat7e or decreased expression of lama4 in anchorage-dependent HeLa cells reduced cellular adhesion. Collectively, the results of this study are consistent with the roles siat7e and lama4 play in adhesion processes in vivo and indicate modifying the expression of either gene can influence adhesion in HeLa cells. The strategy of applying bioinformatics techniques to characterize and manipulate phenotypic behaviors is a powerful tool for altering the properties of various cell lines for desired biotechnology objectives.

Selective adsorption of block copolymers on patterned surfaces

Adsorption of copolymers on patterned surfaces is studied using lattice modeling and multiple Markov chain Monte Carlo methods. The copolymer is composed of alternating blocks of A and B monomers, and the adsorbing surface is composed of alternating square blocks containing C and D sites. Effects of interaction specificity on the adsorbed pattern of the copolymer and the sharpness of the adsorption transition are investigated by comparing three different models of copolymer-surface interactions. Analyses of the underlying energy distribution indicate that adsorption transitions in our models are not two-state-like. We show how the corresponding experimental question may be addressed by calorimetric measurements as have been applied to protein folding. Although the adsorption transitions are not "first order" or two-state-like, the sharpness of the transition increases when interaction specificity is enhanced by either including more attractive interaction types or by introducing repulsive interactions. Uniformity of the pattern of the adsorbed copolymer is also sensitive to the interaction scheme. Ramifications of the results from the present minimalist models of pattern recognition on the energetic and statistical mechanical origins of undesirable nonspecific adsorption of synthetic biopolymers in cellular environments are discussed.

Stem cell attachment to layer-by-layer assembled TiO2 nanoparticle thin films

Surface topography is one of the most important factors influencing the attachment and spreading of cells. In the present study, layer-by-layer assembled titanium dioxide (TiO2) nanoparticle thin films were chosen for attachment, proliferation and spreading studies on mouse mesenchymal stem cells (MSC). Increasing surface roughness was observed with increasing number of layer-by-layer assembled TiO2 thin films. Four layer TiO2 thin film showed higher number of attached cells than a one layer thin film and control surfaces. MSCs experienced no cytotoxic effects after culture on the TiO2 coated substrates as observed from the cytotoxicity tests. Cell spreading, visualized with scanning electron microscopy, showed a faster rate of spreading on a rougher surface. Cells on a four-layer substrate, at 12 h showed complete spreading, where as most of the cells on a control surface and a one-layer surface, at 24 h, retained a rounded morphology. In conclusion, TiO2 nanoparticle thin films were successfully assembled in alternation with polyelectrolytes and in-vitro studies with MSC showed an increase in the attachment and faster spreading of cells on rougher surfaces.

A seeding device for tissue engineered tubular structures

One of the challenges in the tissue engineering of tubular tissues and organs is the efficient seeding of porous scaffolds with the desired cell type and density in a short period of time, without affecting cell viability. Though different seeding techniques have been investigated, a fast, reproducible, and efficient bulk seeding method with uniform cellular distribution has yet to be reported. In this paper, a novel seeding device utilizing the synergistic effects of vacuum, centrifugal force and flow has been developed and analyzed. The device allows porous tubular scaffolds to be uniformly bulk seeded as well as luminally surface-seeded with cells. Porous tubular polymer scaffolds were bulk and surface-seeded with cell suspensions, and cell viability and seeding efficiency were subsequently assessed. A rigorous quantitative analysis of shear stresses acting on the cells during the seeding process, and of cell location within the scaffolds following seeding was also performed. Our results showed that the scaffolds were uniformly seeded along the longitudinal and circumferential directions within the tube wall without affecting cell viability or exposing them to excessive shear stresses.