Study of a heavy metal biosorption onto raw and chemically modified Sargassum sp. via spectroscopic and modeling analysis

A novel porous lignocellulosic standing hierarchical hydroxyapatite for enhanced aqueous copper(II) removal

Potentially toxic metal-polluted water resources are a heavily discussed topic the pollution by potentially toxic metals can cause significant health risks. Nanomaterials are actively developed towards providing high specific surface area and creating active adsorption sites for the treatment and remediation of these polluted waters. In an effort to tackle the limitations of conventional type adsorbents, nano-hydroxyapatite (HAp) was developed in this study by in situ generation onto wood powder, resulting in the formation of uniform hybrid powder (HAp@wood composite) structure consisting of HAp nanoparticles that showed the removal efficiency up to 80 % after 10 min; the maximum adsorption capacity for Cu(II) ions (98.95 mg/g-HAp) was higher compared to agglomerated nano-HAp (72.85 mg/g-HAp). The adsorption capacity of Cu(II) remained stable (89.85-107.66 mg/g-HAp) during the four adsorption-desorption cycles in multi-component system, thereby demonstrating high selectivity for Cu(II). This approach of using nanoparticle is relatively simple yet effective in improving the adsorption of potentially toxic metals and the developed approach can be used to develop advanced nanocomposites in commercial wastewater treatment.

Enhanced microbial reduction of Cr(VI) in soil with biochar acting as an electron shuttle: Crucial role of redox-active moieties

Biochar has been proven to participate in the biotic reduction of hexavalent chromium (Cr(VI)) in environment since its involvement may accelerate the extracellular electron transfer (EET). However, roles of the redox-active moieties and the conjugated carbon structure of biochar in this EET process remain unclear. In this study, 350 °C and 700 °C were selected to produce biochar with more O-containing moieties (BC350) or more developed conjugated structures (BC700), and their performances in the microbial reduction of soil Cr(VI) were investigated. Our results showed that BC350 presented a 241% increase of Cr(VI) microbial reduction after 7-day incubation, much higher than that of BC700 (39%), suggesting that O-containing moieties might play more important roles in accelerating the EET process. Biochar, especially BC350 could serve as an electron donor for microbial anaerobic respiration, but its contribution (73.2%) as an electron shuttle for EET was dominant to the enhanced Cr(VI) reduction. The positive correlation between electron exchange capacities (EECs) of pristine and modified biochars and the corresponding maximum reduction rates of Cr(VI) evidenced the crucial role of redox-active moieties in electron shuttling. Moreover, EPR analysis suggested the nonnegligible contribution of semiquinone radicals in biochars to the accelerated EET process. This study demonstrates the crucial role of redox-active moieties, i.e., O-containing moieties in mediating the EET process during the microbial reduction of Cr(VI) in soil. Findings obtained will advance the current understanding of biochar as an electron shuttle participating in the biogeochemical processes of Cr(VI).

New insights into the interactions between Pb(II) and fruit waste biosorbent

Fruit waste is a sustainable biosorbent for heavy metal removal from wastewater. Elucidation of adsorption mechanism is imperative for the process control and development of effective adsorbents. In this study, watermelon rind (WR) exhibited selective and efficient Pb(II) adsorption with a maximum uptake of 230.5 mg/g at pH 5.0. The WR-packed bed column showed high Pb(II) uptake and robust durability over 10 adsorption-desorption cycles with long breakthrough time of 8-13 h (89-144 bed volume), and 95% of sequestered Pb(II) was rapidly desorbed in 1-2 h by 0.05 M HCl. Spectroscopic characterization by FTIR and XPS identified hydroxyl, carboxyl, amine, and ether groups as the binding sites for Pb(II) via the binding force of complexation. Physicochemical analysis showed that ion exchange with Mg²⁺ and Ca²⁺ accounted for 19% of Pb(II) adsorption by WR; electrostatic attraction and microprecipitation jointly contributed. Quantum chemistry simulation verified the interactions between Pb(II) and binding sites and revealed carboxyl was the preferential functional group. The findings corroborate the applicability of WR in scale-up Pb(II) removal/recovery from wastewater and elaborate the mechanisms of Pb(II) adsorption by the WR biosorbent. This also provides insights into the behavior of heavy metals in other liquid/solid interfaces.

Volatilisations of ammonia from the soils amended with modified and nitrogen-enriched biochars

Biochar's capacity to abate NH₃ emissions from fertilised agricultural soils may be enhanced through both modifications and formulation of slow-release biochar-based N fertilisers but there is a dearth of data in this area. Sulphuric acid (H₂SO₄), hydrogen peroxide (H₂O₂) and potassium hydroxide (KOH) were used to modify biochars which are denoted as BSAD, BHPO and BKOH, respectively. Nitrogen (N) enrichment was performed using urea and ammonium nitrate and the enriched biochars are denoted as BUR and BAN, respectively. The biochars were characterised by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), Fourier-transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). The ammonia abatement potentials of both the modified and N-enriched biochars were assessed in the incubation experiments which lasted for 30 days. Urea was used as a control while non-modified biochar (PrBC) was included for comparison. Compared to the control, PrBC, BKOH, BHPO, BSAD, BUR and BAN attenuated gaseous NH₃ emissions by 57.62%, 63.06%, 73.23% and 74.85%, 79.93% and 82.88%, respectively. Biochar modifications increased the content of oxygen containing surface groups especially carboxyl and sulphoxide in the case of BSAD as depicted from the instrumental analysis data, which most probably increased the sorption of NH₃ and its transformation to nitrates thus, resulting in a higher NH₃ abatement capacity than that of PrBC. XPS data indicated that N-enrichment resulted in reactions of N with the surface groups of biochar which slowed its release, concomitantly lowering NH₃ volatilisation better than even the modified biochars.

Removal of Cr(VI) by biochar derived via co-pyrolysis of oily sludge and corn stalks

The co-pyrolysis of oily sludge with biomass to prepare carbon materials is not only an effective way to mitigate oily sludge pollution, but it is also a method of obtaining carbon materials. In this study, a carbon material (OS-CS AC) was obtained by the direct co-pyrolysis of oily sludge (OS) and corn stalks (CS) and then applied to Cr(VI) removal. According to the hydroxy and carboxy masking experiments and the characterization of OS-CS AC by FT-IR, SEM, XPS, XRD, and N₂ physical adsorption–desorption, Cr(VI) can be adsorbed efficiently through pore filling, the surface oxygen-containing functional groups can promote the reduction of Cr(VI) to Cr(III) through electron donors, and the greater the electrostatic attraction between the electron-donating functional groups of OS-CS AC and the Cr(VI) is, the stronger the ability to remove Cr(VI). In addition, the removal process was discussed, and the results indicated that the McKay kinetic model, Langmuir isotherm model and Van't Hoff thermodynamic model were the most suitable models for removal. The main factors affecting the removal of Cr(VI) were discussed, and the removal of Cr(VI) reached 99.14%, which gives a comprehensive utilization way of oily sludge and corn stalks.

Experimental and DFT investigation on N-functionalized biochars for enhanced removal of Cr(VI)

In this study, N-functionalized biochars with varied structural characteristics were designed by loading poplar leaf with different amounts of urea at 1:1 and 1:3 ratios through pyrolysis method. The addition of urea significantly increased the N content of biochar and facilitated the formation of amine (-NH-, -NH₂), imine (-HCNH), benzimidazole (-C₇H₅N₂), imidazole (-C₃H₃N₂), and pyrimidine (-C₄H₃N₂) groups due to substitution reaction and Maillard reaction. The effect of pH on Cr(VI) removal suggested that decrease in solution pH favored the formation of electrostatic attraction between the protonated functional groups and HCrO₄^-. And, experimental and density functional theory study were used to probe adsorption behaviors and adsorption mechanism which N-functionalized biochars interacted with Cr(VI). The protonation energy calculations indicated that N atoms in newly formed N-containing groups were better proton acceptors. Adsorption kinetics and isotherm experiments exhibited that N-functionalized biochars had greater removal rate and removal capacity for Cr(VI). The removal rate of Cr(VI) on N-functionalized biochar was 10.5-15.5 times that of untreated biochar. Meanwhile, N-functionalized biochar of NB3 with the largest number of adsorption sites for -C₇H₅N₂, -NH₂, -OH, -C₃H₃N₂, and phthalic acid (-C₈H₅O₄) exhibited the supreme adsorption capacity for Cr(VI) through H bonds and the highest adsorption energy was -5.01 kcal/mol. These mechanistic findings on the protonation and adsorption capacity are useful for better understanding the functions of N-functionalized biochars, thereby providing a guide for their use in various environmental applications.

Bioadsorbents from algae residues for heavy metal ions adsorption: chemical modification, adsorption behaviour and mechanism

Biosorption is an emerging technology for the removal of heavy metals from industrial wastewater by natural or modified biomass. In this study, we proposed a novel protocol for making full use of seaweeds. Brown seaweed Sargassum carpophyllum residue (SCR) and green seaweed Caulerpa lentillifera residue (CLR) were obtained after extraction of the bioactive polysaccharides. The obtained residues were further chemical modified by butanedioic anhydride to obtained respective carboxylated product, named CSCR and CCLR. According to the titration results, CSCR and CCLR contained 2.77 and 2.12 mmol/g of carboxyl group. After modification, the adsorption capacity for metal ions increased by 3-6 times. The adsorption capacity of CSCR for Cu²⁺, Pb²⁺, Cd²⁺ and Mn²⁺ was 52.37, 107.11, 85.62, and 43.52 mg/g, and that of CCLR was 78.10, 108.80, 87.30 and 57.80 mg/g, respectively. The adsorption was well described by the pseudo-second-order kinetic model and Langmuir adsorption isotherm equation.

Potassium phosphate/magnesium oxide modified biochars: Interfacial chemical behaviours and Pb binding performance

Removal of lead (Pb) from aqueous solutions by biochar is a promising method. In this study, wheat straw biochar (WBC) was modified by phosphate/magnesium via pre-treatment of biomass and post-treatment of biochar, noting as WBC_PMA and WBC_PMB, respectively. Based on Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analyses, phosphate/magnesium chemically bound to the structures of biochar surface, increasing the contents of polar groups (i.e., -COOH and -OH) and phosphorus-containing compounds, mainly Mg₃(PO₄)₂ and Mg₂P₂O₇. Owing to pyrolysis process enhancing loading ability of phosphate/magnesium, WBC_PMA possessed more active functional groups than WBC_PMB. Results showed that maximum sorption capacity of Pb was improved by modifications, following the sequence of WBC_PMA (470.09 mg/g) > WBC_PMB (308.39 mg/g) > WBC (59.93 mg/g). Pseudo-second-order kinetics and thermodynamics study indicated that chemisorption was involved in sorption process. Precipitation, complexation and cation exchange dominated Pb sorption and the corresponding contributions accounted for 17.89-32.73%, 28.84-46.22%, and 21.05-53.27%, respectively. Additionally, desorption characteristics of Pb illustrated that WBC_PMA owned more prominent stabilization ability than that of WBC and WBC_PMB. The findings of this study suggested that pre-modification method increased the contents of active groups in biochar and strengthened the removal efficiency of Pb ultimately. Due to the complexity of the actual Pb-containing wastewater environment, it was necessary to evaluate the effects of various factors on the stabilization performance of the pre-modified biochar in further.

Microscopic mechanism about the selective adsorption of Cr(VI) from salt solution on O-rich and N-rich biochars

The adsorption of Cr(VI) on biochars can be suppressed by coexisting anions, but the roles of O-containing functional groups and in particular N-containing functional groups are unclear. In this study, we combined spectroscopic and molecular simulation approaches to investigate the selective adsorption of Cr(VI) on the O-rich (PB, UB1) and N-rich (UB3, UB5) biochars under strong competition of anions. The elemental analysis and pyrolysis-gas chromatography/mass spectrometry indicated that the structures of PB and UB1 were similar, and so were the UB3 and UB5. Quantification of functional groups showed that for UB1, 75.3% of Cr(VI) removal was attributed to O-containing groups, while 53.3-72.7% of that was mediated by N-containing groups in UB3 and UB5. X-ray photoelectron spectra and density functional theory calculations confirmed that for O-rich biochars, surface complexation and strong H-bonds between carboxyl/hydroxyl and HCrO₄^- improved Cr(VI) removal in the presence of anions, while for N-rich biochars, Cr(VI) adsorption was depressed by coexisting anions in the order of Cl^->NO₃^- >SO₄^2- because of the weaker H-bond between protonated amino groups and HCrO₄^-. This study presents a novel approach for quantitative, molecular-level evaluation of the roles of biochar functional groups in the Cr(VI) removal from complex environmental systems.

Adsorption Mechanisms and Characteristics of Hg2+ Removal by Different Fractions of Biochar

The adsorption mechanisms of mercury ion (Hg2+) by different fractions of biochar were studied, providing a theoretical basis and practical value for the use of biochar to remediate mercury contamination in water. Biochar (RC) was prepared using corn straw as the raw material. It was then fractionated, resulting in inorganic carbon (IC), organic carbon (OC), hydroxyl-blocked carbon (BHC), and carboxyl-blocked carbon (BCC). Before and after Hg2+ adsorption, the biochar fractions were characterized by several techniques, such as energy-dispersive X-ray spectroscopy (EDS), Fourier-transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). Obtained results indicate that the reaction mechanisms of RC for Hg2+ removal mainly include electrostatic adsorption, ion exchange, reduction, precipitation, and complexation. The equilibrium adsorption capacity of RC for Hg2+ is 75.56 mg/g, and the adsorption contribution rates of IC and OC are approximately 22.4% and 77.6%, respectively. Despite the lower rate, IC shows the largest adsorption capacity, of 92.63 mg/g. This is attributed to all the mechanisms involved in Hg2+ adsorption by IC, with ion exchange being the main reaction mechanism (accounting for 39.8%). The main adsorption mechanism of OC is the complexation of carboxyl and hydroxyl groups with Hg2+, accounting for 71.6% of the total OC contribution. BHC and BCC adsorb mercury mainly via the reduction–adsorption mechanism, accounting for 54.6% and 54.5%, respectively. Among all the adsorption mechanisms, the complexation reaction of carboxyl and hydroxyl groups with Hg2+ is the dominant effect.

Properties of a commercial κ-carrageenan food ingredient and its durable superabsorbent hydrogels

Physical kappa-carrageenan-based hydrogels are often prepared from dilute aqueous kappa-carrageenan (κ-carrageenan) solutions at the presence of metallic ions or by mixing these solutions with proteins and other polysaccharides. The κ-carrageenan hydrogels have been used for technological purposes; however, there are no reports about the properties of a commercial GENUGEL® κ-carrageenan produced by the CP Kelco. The flame atomic absorption spectrometry shows that the commercial κ-carrageenan comprises a high content of metallic ions (K⁺ = 216.1 g kg^-1, Na⁺ = 6.3 g kg^-1 and Ca²⁺ = 12.5 g kg^-1). The X-ray photoelectron spectroscopy (XPS) indicates the presence of sodium, calcium, and potassium atoms on the as-received κ-carrageenan and its physical hydrogel surfaces. XPS supports the occurrence of a low protein content onto the sample surfaces, as well. The metallic level (especially for K⁺) in the commercial κ-carrageenan plays an essential role in the preparation of durable hydrogels. These materials are prepared by cooling aqueous κ-carrageenan solutions at 4.0 and 5.0 wt%. The gelation temperature is determined by measuring G' &G″ as a function of the temperature. The gelation behavior depends on the κ-carrageenan concentration, as well as the metallic content in the commercial sample. Scanning electron microscopy shows that hydrogels have porous and smooth surfaces. The dried materials swell from 2400 to 3100%, while the disintegration/dissolution test confirms that the samples present high stability in distilled water throughout 14 days. These hydrogels are superabsorbent materials and can be applied in agriculture as soil conditioners.

New Prospects for Modified Algae in Heavy Metal Adsorption

Heavy metal pollution is one of the most pervasive environmental problems globally. Novel finely tuned algae have been proposed as a means to improve the efficacy and selectivity of heavy metal biosorption. This article reviews current research on selective algal heavy metal adsorption and critically discusses the performance of novel biosorbents. We emphasize emerging state-of-the-art techniques that customize algae for enhanced performance and selectivity, particularly molecular and chemical extraction techniques as well as nanoparticle (NP) synthesis approaches. The mechanisms and processes for developing novel algal biosorbents are also presented. Finally, we discuss the applications, challenges, and future prospects for modified algae in heavy metal biosorption.

Equilibrium study of binary mixture biosorption of Cr(III) and Zn(II) by dealginated seaweed waste: investigation of adsorption mechanisms using X-ray photoelectron spectroscopy analysis

The alginate extraction residue (RES) from the Brazilian Sargassum filipendula was successfully employed as biosorbent in this binary equilibrium study, revealing a greater affinity and selectivity for Cr(III) than for Zn(II). Experimental results also revealed that the process is of endothermic nature and well adjusted by Langmuir-Freundlich binary model. The X-ray photoelectron spectroscopy (XPS) analysis revealed that coordination with hydroxyl groups of RES prevailed in Cr removal, followed by carboxyl-metal complexation. As far as Zn(II) is concerned, ion exchange with carboxylate groups of RES was the largest contributor. Nevertheless, scanning electron microscopy coupled with Fourier transform infrared spectroscopy indicated the participation of sulfate functions in a minor degree.

Algal sorbent derived from Sargassum horneri for adsorption of cesium and strontium ions: equilibrium, kinetics, and mass transfer

An algal sorbent derived from Sargassum horneri was prepared and used to adsorb cesium and strontium ions from aqueous solution. The phenomenological mathematical models associated to the predicted equilibrium isotherms were developed to determine the rate-limiting steps of the adsorption process. The maximum adsorption capacity of cesium ion and strontium ion was calculated to be 0.358 and 1.72 mmol g-1, respectively. The adsorption kinetics followed to the pseudo-second-order equation. It was found that adsorption of cesium or strontium ions onto the active sites of the biosorbent was the rate-limiting step. In addition, the external mass transfer and the internal mass transfer cannot be neglected for the adsorption of strontium ion based on the error analysis. The functional groups relevant to the adsorption were carboxyl and sulfate groups.

Sorption of carbendazim on activated carbons derived from rape straw and its mechanism

Due to the production and widespread application of pesticides, pesticide pollution poses a potential danger to human health and the ecosystem. Herein, activated carbons employing rape straw as a precursor were produced using H₃PO₄ as an activating agent at various temperatures (300–600 °C). The activated carbons differed with respect to the physicochemical properties, which were derived from elemental analysis, N₂ sorption–desorption, FTIR, XPS, XRD, pH_pzc, Boehm titration and blocking of the oxygen-containing groups. The oxygen-containing functional groups and the pore structure of the activated carbons obtained from the different preparation conditions were quite different. The as-prepared samples were applied as sorbents to remove carbendazim (CBD). The results indicated that the sorption of CBD was mainly dominated by partitioning at low concentrations of CBD. Meanwhile, electrostatic attractions played a more important role than hydrophobic interactions at a low initial pH; in contrast, as the initial pH increased, the hydrophobic interaction was the predominant sorption mechanism. Therefore, the results can be used to design some efficient and environmentally friendly adsorbents to reduce the risk of organic pollutants, especially organic pesticides, in aqueous solutions.

Due to the production and widespread application of pesticides, pesticide pollution poses a potential danger to human health and the ecosystem.

Development of a novel biochar/PSF mixed matrix membrane and study of key parameters in treatment of copper and lead contaminated water

Mixed matrix membrane (MMM) has attracted increasing attentions in various applications, such as water treatment. In this study, an innovative biochar/polysulfone (PSF) mixed matrix hollow fiber membrane was fabricated by incorporating micro-sized biochar particles in the PSF matrix. It was demonstrated that the membrane was more hydrophilic than the pure PSF membrane. Higher water flux was obtained. The adsorption of copper and lead on the MMM increased as the pH was increased with the maximum adsorption capacity observed at pH > 4.5. The adsorption equilibrium was established in 7 and 12 h for lead and copper, respectively. The adsorption kinetics and isotherm followed the intraparticle surface diffusion model and Freundlich isotherm, respectively. The presence of humic acid (HA) had a little effect on the adsorption, while the ionic strength showed an adverse effect on the removal. In addition, the feed concentration and cross flow rate significantly affected the removal efficiency in a continuous filtration mode. The increase in feed concentration and cross flow rate resulted in a reduction in the volume of treated permeate that had the copper/lead concentrations below the regulated levels for drinking water. The MMM exhibited an excellent regeneration-reuse performance in the removal of both copper and lead. Finally, our mechanism studies indicated that the uptake of heavy metals was controlled by a combination of key reactions of complexation, ion-exchange and precipitation. This study indicated that the MMM can be applied as an effective and eco-friendly material for the treatment of heavy metals contaminated water.

Removal of hexavalent chromium upon interaction with biochar under acidic conditions: mechanistic insights and application

Chromium pollution of soil and water is a serious environmental concern due to potential carcinogenicity of hexavalent chromium [Cr(VI)] when ingested. Eucalyptus bark biochar (EBB), a carbonaceous black porous material obtained by pyrolysis of biomass at 500 °C under oxygen-free atmosphere, was used to investigate the removal of aqueous Cr(VI) upon interaction with the EBB, the dominant Cr(VI) removal mechanism(s), and the applicability to treat Cr(VI)-contaminated wastewater. Batch experiments showed complete removal of aqueous Cr(VI) at pH 1-2; sorption was negligible at pH 1, but ~55% of total Cr was sorbed onto the EBB surface at pH 2. Detailed investigations on unreacted and reacted EBB through Fourier transform infrared spectroscopy and X-ray photoelectron spectrometry (XPS) indicate that the carboxylic groups in biochar played a dominant role in Cr(VI) sorption, whereas the phenolic groups were responsible for Cr(VI) reduction. The predominance of sorption-reduction mechanism was confirmed by XPS studies that indicated ~82% as Cr(III) and ~18% as Cr(VI) sorbed on the EBB surface. Significantly, Cr(VI) reduction was also facilitated by dissolved organic matter (DOM) extracted from biochar. This reduction was enhanced by the presence of biochar. Overall, the removal of Cr(VI) in the presence of biochar was affected by sorption due to electrostatic attraction, sorption-reduction mediated by surface organic complexes, and aqueous reduction by DOM. Relative dominance of the aqueous reduction mechanism depended on a critical biochar dosage for a given electrolyte pH and initial Cr(VI) concentration. The low-cost EBB developed here successfully removed all Cr(VI) in chrome tanning acidic wastewater and Cr(VI)-contaminated groundwater after pH adjustment, highlighting its potential applicability in effective Cr(VI) remediation.

Redox and catalytic properties of biochar-coated zero-valent iron for the removal of nitro explosives and halogenated phenols

A novel biochar-coated zero-valent iron [Fe(0)], which was synthesized with rice straw and Fe(0), was applied to remove nitro explosives (2,4,6-trinitrotoluene and hexahydro-1,3,5-trinitro-1,3,5-triazine) and halogenated phenols (2,4-dibromophenol and 2,4-difluorophenol) from contaminated waters. Due to the presence of biochar on the outside, the removal of nitro explosives and halogenated phenols was significantly enhanced via sorption. The sorbed contaminants were further transformed into reductive products, indicating that the inner Fe(0) played the role of a reductant in the biochar-coated Fe(0). Compared to direct reduction with Fe(0), the reductive transformation with biochar-coated Fe(0) was markedly enhanced, suggesting that the biochar in biochar-coated Fe(0) may act as an electron transfer mediator. Further experiments showed that the surface functional groups of biochar were involved in the catalytic enhancement of electron transfer. Our results suggested that biomass could be used to synthesize a novel sorbent and catalyst for treating redox-sensitive contaminants in natural and engineered systems.

Chemical adsorption of oxytetracycline from aqueous solution by modified molecular sieves

The removal of oxytetracycline (OTC) from aqueous solution on modified molecular sieve via adsorption was investigated in the present work. The copper(II) modified molecular sieve had the much higher adsorbed amount than unmodified one. The bigger pore, the more adsorption sites benefitted for the adsorbed amount of OTC. The exchanged amount of copper(II) and the acid-base property of solution were important factors influencing the removal efficiency. The adsorption kinetics, the adsorption isotherm, the adsorption thermodynamics and the proposed adsorption mechanism were studied. The analysis of adsorption isotherm indicated it is a monolayer adsorption. The fitting with adsorption kinetics, pseudo-second-order model, deduced chemical adsorption is the main rate controlling step. And the new formation of Cu-O chemical bond and the changes at bands of N-H vibration and C-N vibration by Fourier transform infrared spectrometer further confirmed the proposal adsorption mechanism was the chemical complexation of copper(II) in modified 13X with NH₂ group of OTC. As the real exchanged amount of copper(II) was 149.07 mg·g^-1 and the solution pH 7.0, the adsorption capacity of modified 13X for OTC reached the maximum of 2,396 mg·g^-1 (with the initial concentration of 1,000 mg·L^-1).

Characteristics of uranium biosorption from aqueous solutions on fungus Pleurotus ostreatus

Uranium(VI) biosorption from aqueous solutions was investigated in batch studies by using fungus Pleurotus ostreatus biomass. The optimal biosorption conditions were examined by investigating the reaction time, biomass dosage, pH, temperature, and uranium initial concentration. The interaction between fungus biomass and uranium was confirmed using Fourier transformed infrared (FT-IR), scanning electronic microscopy energy dispersive X-ray (SEM-EDX), and X-ray photoelectron spectroscopy (XPS) analysis. Results exhibited that the maximum biosorption capacity of uranium on P. ostreatus was 19.95 ± 1.17 mg/g at pH 4.0. Carboxylic, amine, as well as hydroxyl groups were involved in uranium biosorption according to FT-IR analysis. The pseudo-second-order model properly evaluated the U(VI) biosorption on fungus P. ostreatus biomass. The Langmuir equation provided better fitting in comparison with Freundlich isotherm models. The obtained thermodynamic parameters suggested that biosorption is feasible, endothermic, and spontaneous. SEM-EDX and XPS were additionally conducted to comprehend the biosorption process that could be described as a complex process involving several mechanisms of physical adsorption, chemisorptions, and ion exchange. Results obtained from this work indicated that fungus P. ostreatus biomass can be used as potential biosorbent to eliminate uranium or other radionuclides from aqueous solutions.

Surface Modification of Naturally Available Biomass for Enhancement of Heavy Metal Removal Efficiency, Upscaling Prospects, and Management Aspects of Spent Biosorbents: A Review

Heavy metal pollution in water emerges as a severe socio-environmental problem originating primarily from the discharge of industrial wastewater. In view of the toxic, non-biodegradable, and persistent nature of most of the heavy metal ions, remediation of such components becomes an absolute necessity. Biosorption is an emerging tool for bioremediation that has gained momentum for employing low-cost biological materials with effective metal binding capacities. Even though biological materials possess excellent metal adsorption abilities, they show poor mechanical strength and low rigidity. Other disadvantages include solid-liquid separation problems, possible biomass swelling, lower efficiency for regeneration or reuse, and frequent development of high pressure drop in the column mode that limits its applications under real conditions. To improve the biosorption efficiency, biomasses need to be modified with a simple technique for selective/multi-metal adsorption. This review is intended to cover discussion on biomass modification for enhanced biosorption efficiency, mechanism studies using various instrumental/analytical techniques, and future direction for research and development including the fate of spent biosorbent. In most of the previously published researches, difficulty of the process in scaling up has not been addressed. The current article outlines the application potential of biosorbents in the development of hybrid technology integrated with membrane processes for water and wastewater treatment in industrial scale.

Adsorption behavior of carboxymethyl konjac glucomannan microspheres for fluoride from aqueous solution

The CMKGM–La–Al is characterized by SEM, EDX, and XPS. We find that adsorption mechanism of the adsorbent involved coordination reaction and electrostatic interaction. The schematic diagram of preparation of CMKGM–La–Al is shown as above.

Delivery of tissue plasminogen activator and streptokinase magnetic nanoparticles to target vascular diseases

Thrombolytic therapy for acute myocardial infarction standardly makes use of the medications streptokinase (SK) and tissue plasminogen activator (tPA). In this study, the potential of silica-coated magnetic nanoparticles (SiO2-MNPs) as nanocarriers clinical thrombolytic therapy was investigated. SiO2-MNPs for use in targeted therapeutic delivery of tPA and SK were prepared using a combined technique incorporating controlled precipitation and hydrothermal methods. Response surface methodology (RSM) was employed to evaluate the efficiency of the SiO2-MNPs. The production of SK secreted from Streptococcus equi was enhanced using random mutagenesis. The tPA and SK A were encapsulated by means of a silanizing agent with a surface rich in 3-aminopropyltrimethoxysilane layered around the SiO2-MNPs. Blood clot lysis assays and fibrin-containing agarose plates were used to carry out in vitro thrombolysis testing. The optimum conditions for producing MNPs were found to be at pH=13 and at a temperature of 75°C for 45 min. Culture conditions of 2.75% NaCl concentration at initial pH=7.5 for 90 s under UV resulted in maximum SK activity. The tPA/SK-conjugated SiO2-MNPs (SiO2-MNP-tPA-SK) increased operating stability in whole blood and storage stability in a buffer by 92%. More effective thrombolysis using magnetic targeting was indicated by a 38% reduction in blood clot lysis time achieved with SiO2-MNP-tPA-SK compared to administering the SiO2-MNPs without guidance. The silica-coated magnetic nanocarriers developed in this study show potential for improved clinical thrombolytic therapy.

Enhanced Adsorption of Trivalent Arsenic from Water by Functionalized Diatom Silica Shells

The potential of porous diatom silica shells as a naturally abundant low-cost sorbent for the removal of arsenic in aqueous solutions was investigated in a batch study. The objective of this work was to chemically modify the silica shells of a diatom Melosira sp. with bifunctional (thiol and amino) groups to effectively remove arsenic in its toxic As(III) form (arsenite) predominant in the aquatic environment. Sorption experiments with this novel sorbent were conducted under varying conditions of pH, time, dosage, and As(III) concentration. A maximum adsorption capacity of 10.99 mg g^-1 was achieved within 26 h for a solution containing 12 mg L^-1 As(III) at pH 4 and sorbent dosage of 2 g L^-1. The functionalized diatom silica shells had a surface morphological change which was accompanied by increased pore size at the expense of reduced specific surface area and total pore volume. As(III) adsorption was best fitted with the Langmuir-Freundlich model, and the adsorption kinetic data using pore surface diffusion model showed that both the external (film) and internal (intraparticle) diffusion can be rate-determining for As(III) adsorption. Fourier transform infrared spectroscopy (FTIR) indicated that the thiol and amino groups potentially responsible for As(III) adsorption were grafted on the surface of diatom silica shells. X-ray photoelectron spectroscopy (XPS) further verified that this unique sorbent proceeded via a chemisorption mechanism through the exchange between oxygen-containing groups of neutral As(III) and thiol groups, and through the surface complexation between As(III) and protonated nitrogen and hydroxyl groups. Results indicate that this functionalized bioadsorbent with a high As(III) adsorption capacity holds promise for the treatment of As(III) containing wastewater.

Comparison study of biosorption and coagulation/air flotation methods for chromium removal from wastewater: experiments and neural network modeling

This work aims to compare a biosorption method (BM) and a coagulation–dissolved air flotation method (C/DAFM) as inexpensive and effective means of eliminating hexavalent chromium (Cr[vi]) from industrial wastewater.

Introduction and demonstration of a novel Pb(II)-imprinted polymeric membrane with high selectivity and reusability for treatment of lead contaminated water

Lead contaminant in water has become an issue of great concern due to its high toxicity and easy accumulation in human body. In this study, a novel Pb(II)-imprinted polyvinyl alcohol (PVA)/polyacrylic acid (PAA) membrane (Pb-IM) was prepared based on semi-interpenetrating polymer network for selective lead removal. The chemical stability and lead adsorption performance of the Pb-IM were evaluated. The results revealed that the Pb-IM exhibited high adsorption capacity of 1.003mmol/g for lead, fast adsorption equilibrium within 1.5h, and the adsorption process obeyed Langmuir isotherm model and intraparticle pore diffusion model. The Pb-IM retained high adsorption of lead in the presence of competitive factor, i.e. cadmium. In comparison with non-imprinted PVA/PAA membrane, the Pb-IM possessed a much higher selectivity toward lead versus cadmium, with selectivity coefficient of 70.7. Furthermore, the Pb-IM displayed a high reusability for lead uptake and could maintain 96.32% of the adsorption capacity of virgin Pb-IM after six adsorption/desorption cycles. The FTIR and XPS analyses indicated that carboxyl groups in PAA and hydroxyl groups in PVA were mainly associated with the lead adsorption. Finally, the stability study showed that Pb-IM was quite stable and suitable for water treatment. It can be concluded that the Pb-IM can be provided as a powerful material for the selective removal of lead from aqueous solution.

Sorptive removal of nitro explosives and metals using biochar

The feasibility of using biochar as a sorbent to remove nitro explosives and metals from contaminated water was investigated through batch experiments. Biochar, synthesized using various biomasses, showed a porous structure and a high surface area and includes embedded carbonate minerals. Compared with granular activated carbon, biochar was competitive as a sorbent for removing Cd, Cu, Pb, and Zn from water according to the maximum sorption capacities of the metals. Some biochars also effectively sorbed nitro explosives from water. Correlation analysis between maximum sorption capacities and properties of biochar showed that the sorption capacity of biochar for cationic toxic metals is related to cation exchange capacity and that the sorption capacity of explosives is proportional to surface area and carbon content. Results from X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy analyses and laboratory experiments suggest that surface functional groups may be responsible for the sorption of cationic metals to the biochar surface. In contrast, carbon contents may account for the sorption of explosives, possibly through π-π electron donor-acceptor interactions. Our results suggest that biochar can be an attractive and alternative option in environmental remediation of nitro explosives and metals through sorption and immobilization and that appropriate selection of biochar may be necessary according to the types of contaminant and the properties of biochar.

A comprehensive review on biosorption of heavy metals by algal biomass: materials, performances, chemistry, and modeling simulation tools

Heavy metals contamination has become a global issue of concern due to their higher toxicities, nature of non-biodegradability, high capabilities in bioaccumulation in human body and food chain, and carcinogenicities to humans. A series of researches demonstrate that biosorption is a promising technology for removal of heavy metals from aqueous solutions. Algae serve as good biosorbents due to their abundance in seawater and fresh water, cost-effectiveness, reusability and high metal sorption capacities. This article provides a comprehensive review of recent findings on performances, applications and chemistry of algae (e.g., brown, green and red algae, modified algae and the derivatives) for sequestration of heavy metals. Biosorption kinetics and equilibrium models are reviewed. The mechanisms for biosorption are presented. Biosorption is a complicated process involving ion-exchange, complexation and coordination. Finally the theoretical simulation tools for biosorption equilibrium and kinetics are presented so that the readers can use them for further studies.

Binding of heavy metals by algal biosorbents. Theoretical models of kinetics, equilibria and thermodynamics

Biosorption is an extensively studied technology applied for the removal of heavy metal ions and other pollutants from aqueous solutions. Most biosorption research is focused on the experimentally measured sorption isotherms, kinetics and thermodynamics. The aim of this paper is to review a class of theoretical models developed for the interpretation of such experimental data related to biosorption of metal cations by alginate-containing sorbents (e.g. algal biosorbents). The focus is put on: (i) modeling the biosorption equilibrium isotherms (including the description of the pH and ionic strength effects); (ii) thermodynamics of biosorption; (iii) kinetics of biosorption; and (iv) metal ion binding modes. This review facilitates the choice of the model suitable for the given type of data and describes the most common mistakes made during the data analysis (e.g. the use of incorrect or oversimplified models).

Study of nickel and copper biosorption on brown algae Sargassum angustifolium: application of response surface methodology (RSM)

This study has been focused on the batch culture removal of Cu2+ and Ni2+ ions from the aqueous solution using marine brown algae Sargassum angustifolium. Influences of parameters like pH, initial metal ions concentration and biosorbent dosage on nickel and copper adsorption were also examined using the Box-Behnken design matrix. For biosorption of Cu2+ the optimum pH value was determined as 5.0, optimum biosorbent concentration to 1.0 g/L and optimum initial concentration 0.15 mmol/L. For the biosorption of Ni2+, the optimal condition was the same but the optimum pH value was determined as 6.0. Desorption experiments indicated that CH3COOH and EDTA were efficient desorbents for recovery from Cu2+ and Ni2+. The Langmuir isotherm model was applied to describe the biosorption of the Cu2+ and Ni2+ into S. angustifolium. The maximum uptake of Cu2+ and Ni2+ ions by the S. angustifolium biomass under the optimal conditions was approximately 0.94 and 0.78 mmol/g dry alga, respectively. Response surface models showed that the data were adequately fitted to a second-order polynomial model. Analysis of variance showed a high coefficient of determination value (R2 = 0.993 for Cu2+ and 0.991 for Ni2+) and a satisfactory second-order regression model was derived. In addition, results reported in this research demonstrated the feasibility of employing S. angustifolium as biosorbent for Ni2+ and Cu2+ removal.

Adsorption of heavy metal ions from aqueous solution by carboxylated cellulose nanocrystals

A novel nanoadsorbent for the removal of heavy metal ions is reported. Cotton was first hydrolyzed to obtain cellulose nanocrystals (CNCs). CNCs were then chemically modified with succinic anhydride to obtain SCNCs. The sodic nanoadsorbent (NaSCNCs) was further prepared by treatment of SCNCs with saturated NaHCO3 aqueous solution. Batch experiments were carried out with SCNCs and NaSCNCs for the removal of Pb2+ and Cd2+. The effects of contact time, pH, initial adsorption concentration, coexisting ions and the regeneration performance were investigated. Kinetic studies showed that the adsorption equilibrium time of Pb2+ and Cd2+ was reached within 150 min on SCNCs and 5 min on NaSCNCs. The adsorption capacities of Pb2+ and Cd2+ on SCNCs and NaSCNCs increased with increasing pH. The adsorption isotherm was well fitted by the Langmuir model. The maximum adsorption capacities of SCNCs and NaSCNCs for Pb2+ and Cd2+ were 367.6 mg/g, 259.7 mg/g and 465.1 mg/g, 344.8 mg/g, respectively. SCNCs and NaSCNCs showed high selectivity and interference resistance from coexisting ions for the adsorption of Pb2+. NaSCNCs could be efficiently regenerated with a mild saturated NaCl solution with no loss of capacity after two recycles. The adsorption mechanisms of SCNCs and NaSCNCs were discussed.