Chemical end-grafting of homogeneous polystyrene monolayers on mica and silica surfaces

Fundamentals and Applications of Polymer Brushes in Air

For several decades, high-density, end-tethered polymers, forming so-called polymer brushes, have inspired scientists to understand their properties and to translate them to applications. While earlier research focused on polymer brushes in liquids, it was recently recognized that these brushes can find application in air as well. In this review, we report on recent progress in unraveling fundamental concepts of brushes in air, such as their vapor-swelling and solvent partitioning. Moreover, we provide an overview of the plethora of applications in air (e.g., in sensing, separations or smart adhesives) where brushes can be key components. To conclude, we provide an outlook by identifying open questions and issues that, when solved, will pave the way for the large scale application of brushes in air.

Synthetic strategies to enhance the long-term stability of polymer brush coatings

High-density, end-anchored macromolecules that form so-called polymer brushes are popular components of bio-inspired surface coatings. In a bio-memetic approach, they have been utilized to reduce friction, repel contamination and control...

Asymmetric electrostatic and hydrophobic-hydrophilic interaction forces between mica surfaces and silicone polymer thin films

We have synthesized model hydrophobic silicone thin films on gold surfaces by a two-step covalent grafting procedure. An amino-functionalized gold surface reacts with monoepoxy-terminated polydimethylsiloxane (PDMS) via a click reaction, resulting in a covalently attached nanoscale thin film of PDMS, and the click chemistry synthesis route provides great selectivity, reproducibility, and stability in the resulting model hydrophobic silicone thin films. The asymmetric interaction forces between the PDMS thin films and mica surfaces were measured with the surface forces apparatus in aqueous sodium chloride solutions. At an acidic pH of 3, attractive interactions are measured, resulting in instabilities during both approach (jump-in) and separation (jump-out from adhesive contact). Quantitative analysis of the results indicates that the Derjaguin-Landau-Verwey-Overbeek theory alone, i.e., the combination of electrostatic repulsion and van der Waals attraction, cannot fully describe the measured forces and that the additional measured adhesion is likely due to hydrophobic interactions. The surface interactions are highly pH-dependent, and a basic pH of 10 results in fully repulsive interactions at all distances, due to repulsive electrostatic and steric-hydration interactions, indicating that the PDMS is negatively charged at high pH. We describe an interaction potential with a parameter, known as the Hydra parameter, that can account for the extra attraction (low pH) due to hydrophobicity as well as the extra repulsion (high pH) due to hydrophilic (steric-hydration) interactions. The interaction potential is general and provides a quantitative measure of interfacial hydrophobicity/hydrophilicity for any set of interacting surfaces in aqueous solution.

Enhanced stability of low fouling zwitterionic polymer brushes in seawater with diblock architecture

The successful implementation of zwitterionic polymeric brushes as antifouling materials for marine applications is conditioned by the stability of the polymer chain and the brush-anchoring segment in seawater. Here we demonstrate that robust, antifouling, hydrophilic polysulfobetaine-based brushes with diblock architecture can be fabricated by atom-transfer radical polymerization (ATRP) using initiator-modified surfaces. Sequential living-type polymerization of hydrophobic styrene or methyl methacrylate and commercially available hydrophilic sulfobetaine methacrylamide (SBMAm) monomer is employed. Stability enhancement is accomplished by protecting the siloxane anchoring bond of brushes on the substrate, grafted from silicon oxide surfaces. The degradation of unprotected PSBMAm brushes is clearly evident after a 3 month immersion challenge in sterilized artificial seawater. Ellipsometry and atomic force microscopy (AFM) measurements are used to follow changes in coating thickness and surface morphology. Comparative stability results indicate that surface-tethered poly(methyl methacrylate) and polystyrene hydrophobic blocks substantially improve the stability of zwitterionic brushes in an artificial marine environment. In addition, differences between the hydration of zwitterionic brushes in fresh and salt water are discussed to provide a better understanding of hydration and degradation processes with the benefit of improved design of polyzwitterionic coatings.

The boundary lubrication of chemically grafted and cross-linked hyaluronic acid in phosphate buffered saline and lipid solutions measured by the surface forces apparatus

High molecular weight hyaluronic acid (HA) is present in articular joints and synovial fluid at high concentrations; yet despite numerous studies, the role of HA in joint lubrication is still not clear. Free HA in solution does not appear to be a good lubricant, being negatively charged and therefore repelled from most biological, including cartilage, surfaces. Recent enzymatic experiments suggested that mechanically or physically (rather than chemically) trapped HA could function as an "adaptive" or "emergency" boundary lubricant to eliminate wear damage in shearing cartilage surfaces. In this work, HA was chemically grafted to a layer of self-assembled amino-propyl-triethoxy-silane (APTES) on mica and then cross-linked. The boundary lubrication behavior of APTES and of chemically grafted and cross-linked HA in both electrolyte and lipid 1,2-dioleoyl-sn-glycero-3-phosphocholine (DOPC) solutions was tested with a surface forces apparatus (SFA). Despite the high coefficient of friction (COF) of μ ≈ 0.50, the chemically grafted HA gel significantly improved the lubrication behavior of HA, particularly the wear resistance, in comparison to free HA. Adding more DOPC lipid to the solution did not improve the lubrication of the chemically grafted and cross-linked HA layer. Damage of the underlying mica surface became visible at higher loads (pressure >2 MPa) after prolonged sliding times. It has generally been assumed that damage caused by or during sliding, also known as "abrasive friction", which is the main biomedical/clinical/morphological manifestation of arthritis, is due to a high friction force and, therefore, a large COF, and that to prevent surface damage or wear (abrasion) one should therefore aim to reduce the COF, which has been the traditional focus of basic research in biolubrication, particularly in cartilage and joint lubrication. Here we combine our results with previous ones on grafted and cross-linked HA on lipid bilayers, and lubricin-mediated lubrication, and conclude that for cartilage surfaces, a high COF can be associated with good wear protection, while a low COF can have poor wear resistance. Both of these properties depend on how the lubricating molecules are attached to and organized at the surfaces, as well as the structure and mechanical, viscoelastic, elastic, and physical properties of the surfaces, but the two phenomena are not directly or simply related. We also conclude that to provide both the low COF and good wear protection of joints under physiological conditions, some or all of the four major components of joints-HA, lubricin, lipids, and the cartilage fibrils-must act synergistically in ways (physisorbed, chemisorbed, grafted and/or cross-linked) that are still to be determined.

Tailored covalent grafting of hexafluoropropylene oxide oligomers onto silica nanoparticles: toward thermally stable, hydrophobic, and oleophobic nanocomposites

The modification of silica nanoparticles with hexafluoropropylene oxide (HFPO) oligomers has been investigated. HFPO oligomers with two different average degrees of polymerization (DPn = 8 and 15) were first prepared by anionic ring-opening polymerization, deactivated by methanol, and in some cases postfunctionalized by aminopropyl(tri)ethoxysilane or allylamine. The "grafting onto" reactions of these oligomers were then carried out either on bare silica (reaction between a silanol surface and ethoxy-silanized HFPO) or on silica functionalized by amino groups (in an amidation reaction with methyl ester-ended HFPO) or mercapto groups (via the radical addition of allyl-functionalized HFPO). Hybrid nanoparticles thus obtained were characterized by solid-state (29)Si NMR and FTIR spectroscopies as well as elemental and thermogravimetric analyses. The results assessed a significant yield of covalent grafting of HFPO oligomers when performing the hydrolysis-condensation of ethoxylated HFPO on the bare silica surface, compared to the other two methods that merely led to physically adsorbed HFPO chains. Chemically grafted nanohybrids showed a high thermal stability (up to 400 °C) as well as a very low surface tension (typically 5 mN/m) compared to physisorbed complexes.

Polymer brush covalently attached to OH-functionalized mica surface via surface-initiated ATRP: control of grafting density and polymer chain length

The controlled grafting density of poly(tert-butyl acrylate) was studied on OH-activated mica substrates via surface-initiated atom-transfer radical polymerization (ATRP). By properly adjusting parameters such as the immobilization reaction time and the concentration of an ATRP initiator, a wide range of initiator surface coverages and hence polymer densities on mica were possible. The covalently immobilized initiator successfully promoted the polymerization of tert-butyl acrylate on mica surfaces. The resulting polymer layer thickness was measured by AFM using a step-height method. Linear relationships of the polymer thickness with respect to the molecular weight of the free polymer and with respect to the monomer conversion were observed, suggesting that ATRP is well controlled and relatively densely end-grafted layers were obtained. The polymer grafting density controlled by adjusting the initiator surface coverage was confirmed by the polymer layer swelling capacity and film thickness measurements.

Controlled nitroxide-mediated styrene surface graft polymerization with atmospheric plasma surface activation

Polymer layer growth by free radical graft polymerization (FRGP) and controlled nitroxide-mediated graft polymerization (NMGP) of polystyrene was achieved by atmospheric pressure hydrogen plasma surface activation of silicon. Kinetic polystyrene layer growth by atmospheric pressure plasma-induced FRGP (APPI-FRGP) exhibited a maximum surface-grafted layer thickness (125 A after 20 h) at an initial monomer concentration of [M] 0 = 2.62 M at 85 degrees C. Increasing both the reaction temperature ( T = 100 degrees C) and initial monomer concentration ([M] 0 = 4.36 M) led to an increased initial film growth rate but a reduced polymer layer thickness, due to uncontrolled thermal initiation and polymer grafting from solution. Controlled atmospheric pressure plasma-induced NMGP (APPI-NMGP), using 2,2,6,6-tetramethyl-1-piperidinyloxy (TEMPO), exhibited a linear increase in grafted polystyrene layer growth with time due to controlled surface graft polymerization as well as reduced uncontrolled solution polymerization and polymer grafting, resulting in a polymer layer thickness of 285 A after 60 h at [TEMPO] = 10 mM, [M] 0 = 4.36 M, and T = 120 degrees C. Atomic force microscopy (AFM) surface analysis demonstrated that polystyrene-grafted surfaces created by APPI-NMGP exhibited a high surface density of spatially homogeneous polymer features with a low root-mean-square (RMS) surface roughness ( R rms = 0.36 nm), similar to that of the native silicon surface ( R rms = 0.21 nm). In contrast, polymer films created by APPI-FRGP at [M] 0 = 2.62 M demonstrated an increase in polymer film surface roughness observed at reaction temperatures of 85 degrees C ( R rms = 0.55 nm) and 100 degrees C ( R rms = 1.70 nm). The present study concluded that the current approach to APPI controlled radical polymerization may be used to achieve a grafted polymer layer with a lower surface roughness and a higher fractional coverage of surface-grafted polymers compared to both conventional FRGP and APPI-FRGP.

Stability of silanols and grafted alkylsilane monolayers on plasma-activated mica surfaces

We investigated the effect of physical and chemical modifications of mica surfaces induced by water vapor-based plasma treatments on the stability of silanols and grafted alkylsilane monolayers. The plasma-activated substrates were characterized using XPS, TOF-SIMS, and contact angle measurements. They revealed a large surface coverage of silanol groups (Si-OH) and a loss of aluminum atoms compared to freshly cleaved mica surfaces. The stability of plasma-induced silanol groups was investigated by contact angle measurements using ethylene glycol as a probe liquid. The Si-OH surface coverage decreased rapidly under vacuum or thermal treatment to give rise to hydrophobic dehydrated surfaces. The stability of end-grafted monofunctionalized n-alkylsilanes was investigated in different solvents and at different pH using water contact angle measurements. The degrafting of alkylsilanes from the activated mica was promoted in acidic aqueous solutions. This detachment was associated with the hydrolysis of covalent bonds between the alkylsilanes and the mica surface. The monolayer stability was enhanced by increasing the length of the alkyl chains that probably act as a hydrophobic protective layer against hydrolysis reactions. Stable alkylsilane monolayers in water with pH greater than 5.5 were obtained on mica surfaces activated at low plasma pressure. We attributed this stability to the loss of surface Al atoms induced by the plasma treatment.

Friction and normal interaction forces between irreversibly attached weakly charged polymer brushes

Polyelectrolyte brushes were built on mica by anchoring polystyrene-poly(acrylic acid) (PS-b-PAA) diblock copolymers at a controlled surface density in a polystyrene monolayer covalently attached to OH-activated mica surfaces. Compared to physisorbed polymer brushes, these irreversibly attached charged brushes allow the polymer grafting density to remain constant upon changes in environmental conditions (e.g., pH, salt concentration, compression, and shear). The normal interaction and friction forces as a function of surface separation distance and at different concentrations of added salt (NaCl) were investigated using a surface forces apparatus. The interaction force profiles were completely reversible both on loading and receding and were purely repulsive. For a constant polymer grafting density, the influence of the polyelectrolyte charges and the Debye screening effect on the overall interaction forces was investigated. The experimental interaction force profiles agree very well with scaling models developed for neutral and charged polymer brushes. The variation of the friction force between two PAA brushes in motion with respect to each other as a function of surface separation distance appeared to be similar to that observed with neutral brushes. This similarity suggests that the increase in friction is associated with an increase in mutual interpenetration upon compression as observed with neutral polymers. The effect of the PAA charges and added ions was more significant on the repulsive normal forces than on the friction forces. The reversible characteristics of the normal force profiles and friction measurements confirmed the strong attachment of the PAA brushes to the mica substrate. High friction coefficients (ca 0.3) were measured at relatively high pressures (40 atm) with no surface damage or polymer removal.

Unprecedented covalently attached ATRP initiator onto OH-functionalized mica surfaces

Mica substrates were activated by a plasma method leading to OH-functionalized surfaces to which an atom transfer radical polymerization (ATRP) radical initiator was covalently bound using standard siloxane protocols. The unprecedented covalently immobilized initiator underwent radical polymerization with tert-butyl acrylate, yielding for the first time end-grafted polymer brushes that are covalently linked to mica. The initiator grafting on the mica substrate was confirmed by time-of-flight secondary ion mass spectrometry (TOF-SIMS), while the change in the water contact angle of the OH-activated mica surface was used to follow the change in surface coverage of the initiator on the surface. The polymer brush and initiator film thicknesses relative to the virgin mica were confirmed by atomic force microscopy (AFM). This was done by comparing the atomic step-height difference between a protected area of freshly cleaved mica and a zone exposed to plasma activation, initiator immobilization, and then ATRP.

Direct Measurement of Mechanical and Adhesive Properties of Living Cells Using Surface Forces Apparatus

The adhesive and mechanical properties of living cells assembled into a monolayer on two different substrates were investigated using the surface forces apparatus (SFA) technique. The force measurements allowed elastic and bending moduli of the cells plated on substrates to be determined. The moduli are in good agreement with data reported in the literature for single cells determined using atomic force microscopy. Results confirm that the nature of the cell–substrate interactions can mediate cell mechanical and adhesive properties.