Direct synthesis and structural analysis of nitrogen-doped carbon nanofibers

Mechanism of NCNTs Growth on Foamed Nickel and Thus-Prepared PS Hydrogenation High-Performance Carrier NCNTs@FN

Traditional heterogeneous catalysts are affected in the catalytic hydrogenation of PS by the scale effect, viscosity effect, adhesion effect, and conformational effect, resulting in poor activity and stability. Monolithic Pd-CNTs@FN catalysts could eliminate or weaken the impact of these negative effects. We grew nitrogen-doped carbon nanotubes (NCNTs) on monolithic-foamed nickel (FN) and investigate their growth mechanism. Meanwhile, the feasibility of using the NCNTs@FN carrier for PS hydrogenation reaction was also verified. The growth of NCNTs on FN can be divided into 3 stages: initial growth stage, stable growth stage, and supersaturation stage. Finally, a three-layer structure of NCNT layer, dense carbon layer, and FN skeleton is formed. Two types of structures, nickel-doped carbon nanotubes (NiCNTs) and C-Ni alloy, are formed by combining C and Ni, while four nitrogen-doped structures, NPD, NPR, NG, and NO, are formed by C and N. The prepared carrier exhibited an extremely outstanding specific surface area (2.829 × 106 cm2/g) and strength (no NCNTs falling off after 24 h 500 rpm agitation), as well as high catalytic activity for PS hydrogenation after loaded with Pd (2.13 ± 0.95 nm), with a TOF of up to 27.6 gPS/(gPd•h). After 8 repetitions of the catalyst, there was no significant decrease in activity. This proves the excellent performance of Pd-NCNTs@FN in polymer hydrogenation reactions, laying a solid foundation for further research on the mechanism of NCNTs promoting PS hydrogenation and regulating the growth of NCNTs.

In/Ce Co-doped Li3VO4 and Nitrogen-modified Carbon Nanofiber Composites as Advanced Anode Materials for Lithium-ion Batteries

Li₃VO₄ (LVO) is considered as a novel alternative anode material for lithium-ion batteries (LIBs) due to its high capacity and good safety. However, the inferior electronic conductivity impedes its further application. Here, nanofibers (nLICVO/NC) with In/Ce co-doped Li₃VO₄ strengthened by nitrogen-modified carbon are prepared. Density functional theory calculations demonstrate that In/Ce co-doping can substantially reduce the LVO band gap and achieve orders of magnitude increase (from 2.79 × 10^-4 to 1.38 × 10^-2 S cm^-1) in the electronic conductivity of LVO. Moreover, the carbon-based nanofibers incorporated with 5LICVO nanoparticles can not only buffer the structural strain but also form a good framework for electron transport. This 5LICVO/NC material delivers high reversible capacities of 386.3 and 277.9 mA h g^-1 at 0.1 and 5 A g^-1, respectively. Furthermore, high discharge capacities of 335 and 259.5 mA h g^-1 can be retained after 1200 and 4000 cycles at 0.5 and 1.6 A g^-1, respectively (with the corresponding capacity retention of 98.4 and 78.7%, respectively). When the 5LICVO/NC anode assembles with commercial LiNi_1/3Co_1/3Mn_1/3O₂ (NCM111) into a full cell, a high discharge capacity of 191.9 mA h g^-1 can be retained after 600 cycles at 1 A g^-1, implying an inspiring potential for practical application in high-efficiency LIBs.

Synthesis of efficient Co and N co-doped carbon catalysts with high surface areas for selective oxidation of ethylbenzene

In this manuscript, Co and N co-doped carbon catalysts with high surface areas were prepared via the pyrolysis of cobalt nitrate and 1,10-phenanthroline monohydrate, using Mg(OH)₂ as a pore former, followed by acid etching.

Sulfur-mediated synthesis of N-doped carbon supported cobalt catalysts derived from cobalt porphyrin for ethylbenzene oxidation

Nitrogen-doped carbon supported cobalt catalysts are synthesized by a sulfur-mediated heat treatment.

Facile synthesis of nitrogen-doped unzipped carbon nanotubes and their electrochemical properties

N-UCNTs with a high nitrogen level, large surface areas and good crystallinity are synthesized by pyrolysis of an O-UCNTs/melamine composite.