Tensile Properties of Crystalline Polymers: Random Copolymers of Ethylene

Morphology of impact polypropylene copolymer extruded cast film revealed by confocal Raman imaging

An impact polypropylene copolymer (IPC), composed of polypropylene (PP) and ethylene-propylene copolymer (EPC), was synthesized through two-stage in-reactor polymerization. A systematic investigation of the crystalline structure, thermal behavior, morphology, and tensile properties of the IPC extruded cast film was conducted. Specifically, the morphology of EPC was obtained by confocal Raman imaging by depicting the spatial distribution of the Raman band located at 1064 cm-1. The EPC phase exhibits fibrous morphology with the long axis aligning along the machine direction (MD). A three-dimensional (3D) heterogeneous structure of the IPC cast film obtained by confocal Raman imaging confirms that the fibrous EPC phase is dispersed in a 3D framework of the PP matrix. The mesomorphic phase in the as-prepared cast film transforms to a stable α-form crystal after annealing at 130 °C, which improves the yield strength but decreases the elongation of the cast film. The WAXD and SAXS results indicate that there is no obvious orientation of the crystallites. Thus, the anisotropy of tensile properties in the MD and transverse directions is closely related to the anisotropic phase morphology at the micrometer scale. The results reveal that the mechanical performances of IPC films are determined by the crystalline structure of the PP matrix and the morphology.

Effects of Dynamic Crosslinking on Crystallization, Structure and Mechanical Property of Ethylene-Octene Elastomer/EPDM Blends

The dynamic crosslinking method has been widely used to prepare rubber/plastic blends with thermoplastic properties, and the rubber phase is crosslinked in these blends. Both polyolefin elastomer (POE) and ethylene-propylene-diene monomer rubber (EPDM) can be crosslinked, which is different from usual dynamic crosslinking components. In this paper, dynamic crosslinked POE/EPDM blends were prepared. For POE/EPDM blends without dynamic crosslinking, EPDM can play a nucleation role, leading to POE crystallizing at a higher temperature. After dynamic crosslinking, the crosslinking points hinder the mobility of POE chains, resulting in smaller crystals, but having too many crosslinking points suppresses POE crystallization. Synchrotron radiation studies show that phase separation occurs and phase regions form in non-crosslinked blends. After crosslinking, crosslinking points connecting EPDM and part of POE chains, enabling more POE to enter the EPDM phase and thus weakening phase separation, indicates that dynamic crosslinking improves the compatibility of POE/EPDM, also evidenced by a lower β conversion temperature and higher α conversion temperature than neat POE from dynamic mechanical analysis. Moreover, crosslinking networks hinder the crystal fragmentation during stretching and provide higher strength, resulting in 8.3% higher tensile strength of a 10 wt% EPDM blend than neat POE and almost the same elongation at break. Though excessive crosslinking points offer higher strength, they weaken the elongation at break.

Effect of Ultra-High-Molecular-Weight Molecular Chains on the Morphology, Crystallization, and Mechanical Properties of Polypropylene

The effects of the ultra-high-molecular-weight (UHMW) component of polypropylene (PP) on its rheological properties, crystallization behavior, and solid-state mechanical properties were investigated using various measurement techniques. The terminal relaxation time-determined by measuring the linear viscoelasticity-was increased by adding the UHMW component. The increase in the melt elasticity produced by adding the UHMW component was observed by measuring the steady-state shear flow, although the shear viscosity was not greatly affected. Owing to the long characteristic time of the Rouse relaxation of the UHMW component, PP with the UHMW component formed highly oriented structures through a shear-induced crystallization process. The addition of the UHMW component enhanced the orientation and regularity of crystalline structure for extruded films. Therefore, the Young's modulus, yield stress, and strength were higher in the PP film containing the UHMW component than in one without the UHMW component, irrespective of the direction of tensile deformation.

Improved Properties of Metallocene Polyethylene/Poly(ethylene terephthalate) Blends Processed by an Innovative Eccentric Rotor Extruder

* Correspondence: pmhzhe@scut [...].

Modulating the crystallinity, mechanical properties, and degradability of poly(ε-caprolactone) derived polyesters by statistical and alternating copolymerization

Functionalization of PCL analogues in statistical and alternating manner modulates the thermal, physical and mechanical properties.

Ultrasonic decrosslinking of crosslinked high-density polyethylene: effect of degree of crosslinking

The normalized gel fraction versus the normalized crosslink density of the decrosslinked 1% (a), 2% (b) and 4% (c) XHDPE. Dotted and dashed lines represent Horikx function fits, respectively.

Model Linear Low Density Polyethylenes from the ROMP of 5-Hexylcyclooct-1-ene

Model hexyl-branched linear low density polyethylene (C8-LLDPE) samples were synthesized by the ring-opening metathesis copolymerization (ROMP) of the 5-hexylcyclooct-1-ene (1) and cyclooctadiene (COD), followed by catalytic hydrogenation. The ROMP of 1 and copolymerization of 1 and COD using the Grubbs second generation catalyst (G2) afford polymers with the number of hexyl branches based on the feed composition. The resulting hexyl-branched polymers, poly(1) and poly(1-stat-COD), were completely converted into model C8-LLDPE samples by catalytic hydrogenation. The C8-LLDPE samples exhibit the expected reduction in density on branching content. The melting temperature (Tm), crystallization temperature (Tc), and heat of fusion/crystallization (ΔHm/ΔHc) of these materials were studied by differential scanning calorimetry.