Stepwise Fabrication and Characterization of Ultrathin Hydrogels Prepared from Poly(vinylamine-co-N-vinylformamide) and Poly(acrylic acid) on a Solid Substrate

Thermosensitive multilayer hydrogels of poly(N-vinylcaprolactam) as nanothin films and shaped capsules

We report on nanothin multilayer hydrogels of cross-linked poly(N-vinylcaprolactam) (PVCL) that exhibit distinctive and reversible thermoresponsive behavior. The single-component PVCL hydrogels were produced by selective cross-linking of PVCL in layer-by-layer films of PVCL-NH(2) copolymers assembled with poly(methacrylic acid) (PMAA) via hydrogen bonding. The degree of the PVCL hydrogel film shrinkage, defined as the ratio of wet thicknesses at 25°C to 50°C, was demonstrated to be 1.9±0.1 and 1.3±0.1 for the films made from PVCL-NH(2)-7 and PVCL-NH(2)-14 copolymers, respectively. No temperature-responsive behavior was observed for non-cross-linked two-component films due to the presence of PMAA. We also demonstrated that temperature-sensitive PVCL capsules of cubical and spherical shapes could be fabricated as hollow hydrogel replicas of inorganic templates. The cubical (PVCL)(7) capsules retained their cubical shape when temperature was elevated from 25°C to 50°C exhibiting 21±1% decrease in the capsule size. Spherical hydrogel capsules demonstrated similar shrinkage of 23±1%. The temperature-triggered capsule size changes were completely reversible. Our work opens new prospects for developing biocompatible and nanothin hydrogel-based coatings and containers for temperate-regulating drug delivery, cellular uptake, sensing, and transport behavior in microfluidic devices.

Adhesion of two physically contacting planar substrates coated with layer-by-layer assembled films

Adhesives composed of synthetic and low-cost molecules that are based on simple chemical principles are attractive because of their versatility. In this article, we report adhesion between two planar substrates coated with layer-by-layer (LbL) assembled films of cationic poly(diallyldimethylammonium chloride) (PDDA) and anionic poly(sodium styrenesulfonate) (PSS) and perform lap shear measurements of the adhered substrates. Films prepared on the substrates functioned as adhesives when one substrate coated with the PDDA-surface film contacted the other surface coated with the PSS-surface film under adequate pressure in the presence of water droplets, suggesting that two films adhered on the basis of polyion complex formation. Observations suggested that the adhesives failed at the substrate-film interface rather than at the bulk films. The adhesion was compared between film-coated substrates and noncoated ones. Confocal laser scanning microscopic observation of adhesives composed of fluorescently labeled poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) revealed that the labeled PAH assembled on one substrate was well dispersed, even in a nonlabeled film assembled on another substrate. It was therefore confirmed that after adhesion in the presence of the water component, the polyelectrolytes became intermixed between the glassy films, resulting in changes in the adhesive structure at the substrate-film interface.

Chemical oscillation induced periodic swelling and shrinking of a polymeric multilayer investigated with a quartz crystal microbalance

Poly(acrylic acid- co-3-azidopropyl acrylate) and poly(acrylic acid- co-propargyl acrylate) have been alternately fabricated into a multilayer via the click reaction. The layer-by-layer deposition was monitored with a quartz crystal microbalance with dissipation (QCM-D) in real time. The response of the multilayer under continuous flow of a bromate-sulfite-ferrocyanide solution with pH oscillation has also been investigated by use of QCM-D. As the pH oscillates between 3.1 and 6.6, either the frequency shift (Delta f) or the dissipation shift (Delta D) periodically varies with a constant amplitude, clearly indicating that the multilayer swells and shrinks oscillatedly. The changes of thickness, shear viscosity, and elastic shear modulus further indicate the oscillation.

Amphoteric surface hydrogels derived from hydrogen-bonded multilayers: reversible loading of dyes and macromolecules

We used hydrogen-bonded multilayers of poly(N-vinylpyrrolidone) (PVPON) and poly(methacrylic acid) (PMAA) as precursors for producing surface-bound hydrogels and studied their pH-dependent swelling and protein uptake behavior using in situ attenuated total reflection Fourier transform infrared spectroscopy and in situ ellipsometry. The hydrogels were produced by selective chemical cross-linking between PMAA units using carbodiimide chemistry and ethylenediamine (EDA) as a cross-linking reagent, followed by complete removal of PVPON from the film obtained by exposing the film to pH 7.5. As shown by in situ ellipsometry, hydrogels exhibit distinctive polyampholytic swelling as a function of pH, with minimum swelling at pH 4.2-5.7, and increased film thickness at both lower and higher pH values. Film swelling at lower pH values occurs as a result of the presence of amino groups within the hydrogels, which originate from the one-end attachment of the EDA cross-linker to PMAA chains. The pH-switching of hydrogel swelling was fast and reversible. The degree of hydrogel swelling could be also controlled by varying the time allowed for cross-linking. The produced hydrogels were able to absorb large amounts of dyes and proteins of opposite charge reversibly, in response to pH variations. Finally, we demonstrate that proteins included within the hydrogel can easily be replaced with linear polycations. These surface hydrogels hold promise for bioseparation and controlled delivery applications.

Stimuli-responsive properties of N-isopropylacrylamide-based ultrathin hydrogel films prepared by photo-cross-linking

To develop stimuli-responsive ultrathin polymer films on a solid substrate, a novel photo-cross-linkable polymer with both temperature- and pH-responsive properties was prepared. The photoreactive 4-aminobenzophenone (BP) was introduced onto the side groups of poly(N-isopropylaclylamide-co-2-carboxyisopropylaclylamide) [poly(NIPAAm-co-CIPAAm)]. This copolymer was designed for highly random sequences of comonomers. After the formation of spin-coated polymer films on a solid substrate, UV-light irradiation started the cross-linking reaction. The spin-coating processes and stability of the polymer films were quantitatively monitored by a quartz crystal microbalance (QCM), and the thickness was estimated using an atomic force microscope (AFM). These measurements confirmed the formation of a very plain polymer film, and the film thickness was precisely controlled by the concentration of the polymer solution used for spin coating. Moreover, the obtained films showed a high stability due to the cross-liking reaction and UV irradiation. Cyclic voltammetry using potassium ferricyanide revealed that the ions could permeate the photo-cross-linked ultrathin polymer films. The permeability of the ultrathin hydrogel films was dramatically changed by varying the pH and temperature of the aqueous media. These observations suggest that the preparation of isopropylacrylamide-based stimuli-responsive ultrathin hydrogel films is possible.

Loading and release of charged dyes using ultrathin hydrogels

The anionic dyes methyl orange (MO) and allura red (AR) were used as model drugs to assess the loading and release by layer-by-layer assembled ultrathin hydrogels prepared via the amide formation of poly(acrylic acid-co-N-isopropylacrylamide) with AAc contents of 5, 10, and 15 mol % plus poly(vinylamine hydrochloride). The amount of MO loaded was potentially controlled by changing the dye concentrations, film thickness, and AAc content of the copolymers. The release of AR was controlled by the NaCl concentration and pH. We conclude that the polymeric matrices of ultrathin hydrogels have great potential for the loading and release of charged drugs.