Polyacrylamide Adsorption from Aqueous Solutions on Gold and Silver Surfaces Monitored by the Quartz Crystal Microbalance

Influence of titanium nanoscale surface roughness on fibrinogen and albumin protein adsorption kinetics and platelet responses

Biomaterials with nanoscale topography have been increasingly investigated for medical device applications to improve tissue-material interactions. This study assessed the impact of nanoengineered titanium surface domain sizes on early biological responses that can significantly affect tissue interactions. Nanostructured titanium coatings with distinct nanoscale surface roughness were deposited on quartz crystal microbalance with dissipation (QCM-D) sensors by physical vapor deposition. Physico-chemical characterization was conducted to assess nanoscale surface roughness, nano-topographical morphology, wettability, and atomic composition. The results demonstrated increased projected surface area and hydrophilicity with increasing nanoscale surface roughness. The adsorption properties of albumin and fibrinogen, two major plasma proteins that readily encounter implanted surfaces, on the nanostructured surfaces were measured using QCM-D. Significant differences in the amounts and viscoelastic properties of adsorbed proteins were observed, dependent on the surface roughness, protein type, protein concentration, and protein binding affinity. The impact of protein adsorption on subsequent biological responses was also examined using qualitative and quantitative in vitro evaluation of human platelet adhesion, aggregation, and activation. Qualitative platelet morphology assessment indicated increased platelet activation/aggregation on titanium surfaces with increased roughness. These data suggest that nanoscale differences in titanium surface roughness influence biological responses that may affect implant integration.

Layered piezoelectric structures with arbitrary acoustic termination impedances

Multilayer piezoelectric transducers and resonators are widely used for generating propagating and standing acoustic waves as well as for sensor devices. More recently, layered piezoelectric structures based on thin film technology became increasingly important for electromechanical filters used in mobile phones. As a consequence, analytical mathematical modeling of such structures is of high interest. In this paper, a general rigorous transfer matrix description for one-dimensional (1D) layered structures consisting of piezoelectric, visco-elastic, and dielectric layers of arbitrary number is introduced to characterize the electrical and mechanical behavior of a general piezoelectric transducer or resonator with two electrodes and arbitrary acoustic termination impedances (Rig-1D-model). This model is the most general 1D analytical description of layered piezoelectric structures available and can be used for the characterization of various composite transducer and resonant sensor applications. Considered in detail are layered structures with the technically important cases of only one electromechanically coupled mode, and the structure at one or both outer surfaces is in contact with semi-infinite media. For such devices, it is shown how the frequency dependence of the total electrical admittance and spatial dependence of the displacements can be calculated.

A Two-Phase Model for Adsorption from Solution Using Quartz Crystal Microbalance with Dissipation

Quartz crystal microbalance with dissipation (QCM-D) conveniently monitors mass and mechanical property changes of thin films on solid substrates with exquisite resolution. QCM-D is frequently used to measure dissolved solute/sol adsorption isotherms and kinetics. Unfortunately, currently available methodologies to interpret QCM-D data treat the adlayer as a homogeneous medium, which does not adequately describe solution-adsorption physics. Tethering of the adsorbate to the solid surface is not explicitly recognized, and the liquid solvent is included in the adsorbate mass, which is especially in error for low coverages. Consequently, the areal mass of adsorbate (i.e., solute adsorption) is overestimated. Further, friction is not considered between the bound adsorbate and the free solvent flowing in the adlayer. To overcome these deficiencies, we develop a two-phase (2P) continuum model that self-consistently determines adsorbate and liquid-solvent contributions and includes friction between the attached adsorbate and flowing liquid solvent. We then compare the proposed 2P model to those of Sauerbrey for a rigid adlayer and Voinova et al. for a viscoelastic-liquid adlayer. Effects of 2P-adlayer properties are examined on QCM-D-measured frequency and dissipation shifts, including adsorbate volume fraction and elasticity, adlayer thickness, and overtone number, thereby guiding data interpretation. We demonstrate that distinguishing between adsorbate adsorption and homogeneous-film adsorption is critical; failing to do so leads to incorrect adlayer mass and physical properties.

Data evaluation for surface-sensitive label-free methods to obtain real-time kinetic and structural information of thin films: A practical review with related software packages

Interfacial layers are important in a wide range of applications in biomedicine, biosensing, analytical chemistry and the maritime industries. Given the growing number of applications, analysis of such layers and understanding their behavior is becoming crucial. Label-free surface sensitive methods are excellent for monitoring the formation kinetics, structure and its evolution of thin layers, even at the nanoscale. In this paper, we review existing and commercially available label-free techniques and demonstrate how the experimentally obtained data can be utilized to extract kinetic and structural information during and after formation, and any subsequent adsorption/desorption processes. We outline techniques, some traditional and some novel, based on the principles of optical and mechanical transduction. Our special focus is the current possibilities of combining label-free methods, which is a powerful approach to extend the range of detected and deduced parameters. We summarize the most important theoretical considerations for obtaining reliable information from measurements taking place in liquid environments and, hence, with layers in a hydrated state. A thorough treamtmaent of the various kinetic and structural quantities obtained from evaluation of the raw label-free data are provided. Such quantities include layer thickness, refractive index, optical anisotropy (and molecular orientation derived therefrom), degree of hydration, viscoelasticity, as well as association and dissociation rate constants and occupied area of subsequently adsorbed species. To demonstrate the effect of variations in model conditions on the observed data, simulations of kinetic curves at various model settings are also included. Based on our own extensive experience with optical waveguide lightmode spectroscopy (OWLS) and the quartz crystal microbalance (QCM), we have developed dedicated software packages for data analysis, which are made available to the scientific community alongside this paper.

Adsorption of Amyloidogenic Peptides to Functionalized Surfaces Is Biased by Charge and Hydrophilicity

Surfaces are abundant in living systems, such as in the form of cellular membranes, and govern many biological processes. In this study, the adsorption of the amyloidogenic model peptides GNNQQNY, NNFGAIL, and VQIVYK as well as the amyloid-forming antimicrobial peptide uperin 3.5 (U3.5) were studied at low concentrations (100 μM) to different surfaces. The technique of a quartz crystal microbalance with dissipation monitoring (QCM-D) was applied as it enables the monitoring of mass binding to sensors at nanogram sensitivity. Gold-coated quartz sensors were used as unmodified gold surfaces or functionalized with self-assembled monolayers (SAMs) of alkanethiols (terminated as methyl, amino, carboxyl, and hydroxyl) resulting in different adsorption affinities of the peptides. Our objective was to evaluate the underlying role of the nature and feature of interfaces in biological systems which could concentrate peptides and impact or trigger peptide aggregation processes. In overall, the largely hydrophobic peptides adsorbed with preference to hydrophobic or countercharged surfaces. Further, the glycoprotein lubricin (LUB) was tested as an antiadhesive coating. Despite its hydrophilicity, the adsorption of peptides to LUB coated sensors was similar to the adsorption to unmodified gold surfaces, which indicates that some peptides diffused through the LUB layer to reach the underlying gold sensor surface. The LUB protein-antiadhesive is thus more effective as a biomaterial coating against larger biomolecules than small peptides under the conditions used here. This study provides directions toward a better understanding of amyloid peptide adsorption to biologically relevant interfaces, such as cellular membranes.

Response surface methodology approach for the optimisation of adsorption of hydrolysed polyacrylamide from polymer-flooding wastewater onto steel slag: a good option of waste mitigation

Wastewater produced from polymer flooding in oil production features high viscosity and chemical oxygen demand because of the residue of high-concentration polymer hydrolysed polyacrylamide (HPAM). In this study, steel slag, a waste from steel manufacturing, was studied as a low-cost adsorbent for HPAM in wastewater. Optimisation of HPAM adsorption by steel slag was performed with a central composite design under response surface methodology (RSM). Results showed that the maximum removal efficiency of 89.31% was obtained at an adsorbent dosage of 105.2 g/L, contact time of 95.4 min and pH of 5.6. These data were strongly correlated with the experimental values of the RSM model. Single and interactive effect analysis showed that HPAM removal efficiency increased with increasing adsorbent dosage and contact time. Efficiency increased when pH was increased from 2.6 to 5.6 and subsequently decreased from 5.6 to 9.3. It was observed that removal efficiency significantly increased (from 0% to 86.1%) at the initial stage (from 0 min to 60 min) and increased gradually after 60 min with an adsorbent dosage of 105.2 g/L, pH of 5.6. The adsorption kinetics was well correlated with the pseudo-second-order equation. Removal of HPAM from the studied water samples indicated that steel slag can be utilised for the pre-treatment of polymer-flooding wastewater.

Effects of guanidino modified aminoglycosides on mammalian membranes studied using a quartz crystal microbalance

The increase in bacterial and viral resistance to current therapeutics has led to intensive research for new antibacterial and antiviral agents. Among these, aminoglycosides and their guanidino derivatives are potent candidates targeting specific RNA sequences. It is necessary that these substances can pass across mammalian membranes in order to reach their intracellular targets. This study investigated the effects of the aminoglycosides kanamycin A and neomycin B and their guanidino derivatives on mammalian mimetic membranes using a quartz crystal microbalance with dissipation monitoring (QCM-D). Lipid bilayers as membrane models were deposited onto gold coated quartz crystals and aminoglycosides added afterwards. Notably, the guanidino derivatives exhibited an initial stiffening of the membrane layer indicating a quick insertion of the planar guanidino groups into the membrane. The guanidino derivatives also reached their maximum binding to the membrane at lower concentrations than the native compounds. Therefore, these modified aminoglycosides are promising agents for the development of new antimicrobial treatments.

Controlling the Integration of Polyvinylpyrrolidone onto Substrate by Quartz Crystal Microbalance with Dissipation To Achieve Excellent Protein Resistance and Detoxification

Blood purification systems, in which the adsorbent removes exogenous and endogenous toxins from the blood, are widely used in clinical practice. To improve the protein resistance of and detoxification by the adsorbent, researchers can modify the adsorbent with functional molecules, such as polyvinylpyrrolidone (PVP). However, achieving precise control of the functional molecular density, which is crucial to the activity of the adsorbent, remains a significant challenge. In the present study, we prepared a model system for blood purification adsorbents in which we controlled the integration density of PVP molecules of different molecular weights on an Au substrate by quartz crystal microbalance with dissipation (QCM-D). We characterized the samples with atomic force microscopy, X-ray photoelectron spectroscopy, and QCM-D and found that the molecular density and the chain length of the PVP molecules played important roles in determining the properties of the sample. At the optimal condition, the modified sample demonstrated strong resistance to plasma proteins, decreasing the adsorption of human serum albumin (HSA) and fibrinogen (Fg) by 92.5% and 79.2%, respectively. In addition, the modified sample exhibited excellent detoxification, and the adsorption of bilirubin increased 2.6-fold. Interestingly, subsequent atomistic molecular dynamics simulations indicated that the favorable interactions between PVP and bilirubin were dominated by hydrophobic interactions. An in vitro platelet adhesion assay showed that the adhesion of platelets on the sample decreased and that the platelets were maintained in an inactivated state. The CCK-8 assay indicated that the modified sample exhibited negligible cytotoxicity to L929 cells. These results demonstrated that our method holds great potential for the modification of adsorbents in blood purification systems.

Thickness dependent effective viscosity of a polymer solution near an interface probed by a quartz crystal microbalance with dissipation method

The solution viscosity near an interface, which affects the solution behavior and the molecular dynamics in the solution, differs from the bulk. This paper measured the effective viscosity of a dilute poly (ethylene glycol) (PEG) solution adjacent to a Au electrode using the quartz crystal microbalance with dissipation (QCM-D) technique. We evidenced that the effect of an adsorbed PEG layer can be ignored, and calculated the zero shear rate effective viscosity to remove attenuation of high shear frequency oscillations. By increasing the overtone n from 3 to 13, the thickness of the sensed polymer solution decreased from ~70 to 30 nm. The zero shear rate effective viscosity of the polymer solution and longest relaxation time of PEG chains within it decrease with increasing solution thickness. The change trends are independent of the relation between the apparent viscosity and shear frequency and the values of the involved parameter, suggesting that the polymer solution and polymer chains closer to a solid substrate have a greater effective viscosity and slower relaxation mode, respectively. This method can study the effect of an interface presence on behavior and phenomena relating to the effective viscosity of polymer solutions, including the dynamics of discrete polymer chains.

Self-assembled reduced graphene oxide/polyacrylamide conductive composite films

Substrate supported conductive thin films are prepared by the self-assembly of graphene oxide (GO) on a cationic polyacrylamide (CPAM) layer followed by a subsequent chemical reduction. During self-assembly, the dispersed GO nanosheets with a negative zeta potential from solution are spontaneously assembled onto the positively charged CPAM adsorption layer. In addition, CPAM adsorption on the substrate is studied with an electrochemical quartz crystal microbalance (EQCM), showing adsorption stabilization could be established in less than 150 s. The electrostatic interactions between GO and CPAM are investigated by changing the polarization potential with EQCM for the first time, and optimal conditions for facilitating self-assembly are determined. The self-assembled GO/CPAM films are further characterized by Raman spectroscopy, infrared spectroscopy and atomic force microscopy. Importantly, reduced GO (R-GO)/CPAM composite films exhibiting a sheet resistance of 3.1 kΩ/sq can be obtained via in situ reduction in sodium borohydride for 20 min at room temperature. This provides a simple, highly effective, and green route to prepare conductive graphene-based composite thin films.

Frequency shift of a crystal quartz resonator in thickness-shear modes induced by an array of hemispherical material units

A two-dimensional model was established to study the dynamic characteristics of a quartz crystal resonator with the upper surface covered by an array of hemispherical material units. A frequency-dependent equivalent mass ratio was proposed to simulate the effect of the covered units on frequency shift of the resonator system. It was found that the equivalent mass ratio alternately becomes positive or negative with change of shear modulus and radius of each material unit, which indicates that the equivalent mass ratio is strongly related to the vibration mode of the covered loadings. The further numerical results show the cyclical feature in the relationship of frequency shift and shear modulus/radius as expected. The solutions are useful in the analysis of frequency stability of quartz resonators and acoustic wave sensors.

Probing adsorption of polyacrylamide-based polymers on anisotropic Basal planes of kaolinite using quartz crystal microbalance

Quartz crystal microbalance with dissipation (QCM-D) was applied to investigate the adsorption characteristics of polyacrylamide-based polymers (PAMs) on anisotropic basal planes of kaolinite. Kaolinite basal planes were differentiated by depositing kaolinite nanoparticles (KNPs) on silica and alumina sensors in solutions of controlled pH values. Adsorption of an in-house synthesized organic-inorganic Al(OH)3-PAM (Al-PAM) as an example of cationic hybrid PAM and a commercially available partially hydrolyzed polyacrylamide (MF1011) as an example of anionic PAM was studied. Cationic Al-PAM was found to adsorb irreversibly and preferentially on tetrahedral silica basal planes of kaolinite. In contrast, anionic MF1011 adsorbed strongly on aluminum-hydroxy basal planes, while its adsorption on tetrahedral silica basal planes was weak and reversible. Adsorption study revealed that both electrostatic attraction and hydrogen-bonding mechanisms contribute to adsorption of PAMs on kaolinite. The adsorbed Al-PAM layer was able to release trapped water overtime and became more compact, while MF1011 film became more dissipative as backbones stretched out from kaolinite surface with minimal overlapping. Experimental results obtained from this study provide clear insights into the phenomenon that governs flocculation-based solid-liquid separation processes using multicomponent flocculants of anionic and cationic nature.

The design of in vitro liver sinusoid mimics using chitosan-hyaluronic acid polyelectrolyte multilayers

Interactions between hepatocytes and liver sinusoidal endothelial cells (LSECs) are essential for the development and maintenance of hepatic phenotypic functions. We report the assembly of three-dimensional liver sinusoidal mimics comprised of primary rat hepatocytes, LSECs, and an intermediate chitosan-hyaluronic acid polyelectrolyte multilayer (PEM). The height of the PEMs ranged from 30 to 55 nm and exhibited a shear modulus of approximately 100 kPa. Hepatocyte-PEM cellular constructs exhibited stable urea and albumin production over a 7-day period, and these values were either higher or similar to cells cultured in a collagen sandwich. This is of significance because the thickness of a collagen gel is approximately 1000-fold higher than the height of the chitosan-hyaluronic acid PEM. In the hepatocyte-PEM-LSEC liver-mimetic cellular constructs, LSEC phenotype was maintained, and these cultures exhibited stable urea and albumin production. CYP1A1/2 activity measured over a 7-day period was significantly higher in the hepatocyte-PEM-LSEC constructs than in collagen sandwich cultures. A 16-fold increase in CYP1A1/2 activity was observed for hepatocyte-PEM-10,000 LSEC samples, thereby suggesting that interactions between hepatocytes and LSECs are critical in enhancing the detoxification capability in hepatic cultures in vitro.

Characterization of Matrigel interfaces during defined human embryonic stem cell culture

Differences in attachment, proliferation, and differentiation were measured for human embryonic stem (hES) cells cultured on various substrata coated with Matrigel, a blend of extracellular matrix proteins derived from murine tumor cells. The authors observed that hES cells attach and grow poorly on Matrigel adsorbed onto polystyrene, while they proliferate when exposed to Matrigel adsorbed onto glass or oxygen plasma treated polystyrene (e.g., "tissue culture" treated polystyrene). Furthermore, hES cells grown on the Matrigel-coated tissue culture polystyrene are less likely to differentiate than those grown on the Matrigel-coated glass. To assess the mechanism for these observations, they replicated the cell culture interface in a quartz crystal microbalance with dissipation monitoring. In addition, they used ellipsometry and scanning electron microscopy to determine the thickness and topography of Matrigel on the varying surfaces. Matrigel formed a viscoelastic multilayer with similar thickness on all three surfaces; however, the network structure was different, where the adsorbed proteins formed a globular network on polystyrene, and fibrillar networks on the hydrophilic substrates. Matrigel networks on glass were denser than on oxygen plasma treated polystyrene, suggesting that the density and structure of the Matrigel network affects stem cell differentiation, where a denser network promoted uncontrolled hES cell differentiation and did not maintain the self-renewal phenotype.

A nanocell for quartz crystal microbalance and quartz crystal microbalance with dissipation-monitoring sensing

A novel device for nanometer-confinement of soft matter in one dimension (1D) is presented. This nanocell, with very large (up to 10(6):1) cell-radius to cell-height ratio, is tailored as an accessory for quartz crystal microbalance (QCM) and QCM with dissipation-monitoring (QCM-D) sensing to study internal and interfacial energy dissipation phenomena in highly confined (in 1D) soft matter and fluid films (patent pending). The cell consists of two macroscopic plates (diameter of 9 mm), a top (the "lid") and a bottom (the QCM-D sensor), separated by appropriate spacers with heights ranging from below 100 nm up to 10 microm. The surfaces of both the lid and the bottom plate can be mechanically or/and chemically modified, prior to cell assembly, in order to tailor desired interfacial properties for the experiment. The cell is mounted on a standard QCM-D sensor, an AT-cut quartz crystal (the quartz crystal is cut at an angle of 35 degrees from its ZX-plane), forming the bottom plate. We illustrate theoretically and experimentally, as application examples, the use of this device for studies of dynamic mass loading and internal energy dissipation processes in thin films of ethylene glycol respective thin liquid crystal films around the nematic-isotropic phase transition.

Convergence of dissipation and impedance analysis of quartz crystal microbalance studies

A quartz crystal microbalance (QCM) consists of a resonator, which measures the resonance frequency of the quartz slab. When coupled with a network analyzer or coupled with impulse excitation technology, QCM gives additional impedance or dissipation information, respectively. This report provides a set of equations that bring the QCM community a convergence of the dissipation and impedance analysis. Equations derived from the complex frequency shift were applied to quantitatively analyze the dissipation data of polymer brushes obtained from QCM-D. The obtained viscoelastic properties of polymer brushes were then compared with those obtained by the Voigt model method. We believe that these equations will be useful in quantitative studies of interfacial phenomena accompanied with mass or viscoelasticity changes.

Study of film structure and adsorption kinetics of polyelectrolyte multilayer films: effect of pH and polymer concentration

The alternate adsorption of polycation poly(allylamine hydrochloride)(PAH) and the sodium salt of the polymeric dye poly(1-[ p-(3'-carboxy-4'-hydroxyphenylazo)benzenesulfonamido]-1,2-ethandiyl)(PCBS) on quartz crystals coated with silica was studied to understand the structural properties and adsorption kinetics of these films using a combination of quartz crystal microbalance with dissipation monitoring (QCM-D), absorbance, and ellipsometry measurements. In-situ deposition of the polycation PAH on QCM crystals was monitored, followed by rinsing with water and then deposition of the polyanion PCBS. The effects of polymer concentration and pH on film structure, composition and adsorption kinetics were probed. The polymers were adsorbed at neutral pH conditions and at elevated pH conditions where PAH was essentially uncharged to obtain much thicker films. The change in the resonant frequency, Deltaf, of the QCM-D showed a linear decrease with the number of bilayers, a finding consistent with absorbance and ellipsometric thickness measurements which showed linear growth of film thickness. By using the Delta f ratios of PCBS to PAH, the molar ratios of repeat units of PCBS to PAH in the bilayer films as determined by QCM-D were approximately 1:1 at polyelectrolyte concentrations 5-10 mM repeat unit, indicating complete dissociation of the ionic groups. The frequency and dissipation data from the QCM-D experiments were analyzed with the Voigt model to estimate the thickness of the hydrated films which were then compared with thicknesses of dry films measured by ellipsometry. This led to estimates of the water content of the films to be approximately 45 wt %. In addition to the QCM-D, some films were also characterized by a QCM which measures only the first harmonic without dissipation monitoring. For the deposition conditions studied, the deposited mass values measured by the QCM's first harmonic were similar to the results obtained using higher harmonics from QCM-D, indicating that the self-assembled polyelectrolyte films were rigid.

Dispersant adsorption and viscoelasticity of alumina suspensions measured by quartz crystal microbalance with dissipation monitoring and in situ dynamic rheology

Adsorption behavior and water content of adsorbed layers of four dispersants for aqueous ceramic processing were studied by quartz crystal microbalance with dissipation monitoring (QCM-D) on alumina surfaces. The dispersants were a poly(acrylic acid), a lignosulfonate, and two hydrophilic comb copolymers with nonionic polyoxyethylene chains of different molecular weights. A Voigt model was applied to analyze the viscoelastic behavior of the adsorbed dispersant layers. The results from QCM-D were compared with viscoelastic properties determined by in situ dynamic rheology measurements of highly concentrated alumina suspensions during slip casting. The QCM-D results showed that both the poly(acrylic acid) and the lignosulfonate adsorbed in low amounts and in a flat conformation, which generated thin, highly rigid layers less than 1 nm thick. The water content of these layers was found to be around 30% for the lignosulfonate and 35% for the poly(acrylic acid). High casting rate and strength in terms of storage modulus were observed in the final consolidate of the suspensions with the two polyelectrolytes. In contrast, the high molecular weight comb copolymer adsorbed in a less elastic layer with a thickness of about 6 nm, which is enough to provide steric stabilization. The viscous behavior of this layer was attributed to high water content, which was calculated to be around 90%. Such a water-rich layer gives a lubrication effect, which allows for reorientation of particles during the consolidation process, resulting in a high final strength of the ceramic material. During consolidation, the suspension showed a slow casting rate, most likely due to rearrangement facilitated by the lubricating layer. The short-chain comb copolymer adsorbed in a 1.5 nm thick, rigid layer and gave low final strength to the consolidated suspension. It is likely that the poor consolidation behavior is caused by flocculation due to insufficient stabilization of the dispersion.

Study viscoelasticity of ultrathin poly(oligo(ethylene glycol) methacrylate) brushes by a quartz crystal microbalance with dissipation

Ultrathin polymer brushes play important roles in natural and artificial systems. To better understand and utilize their unique behaviors, characterization is a fundamental, but not trivial, task. In this paper, we demonstrated that the quartz crystal microbalance with dissipation (QCM-D) could be applied to study ultrathin poly(oligo(ethylene glycol) methacrylate) brushes. First, we identified four linear relations between dissipation/frequency changes and thickness changes, which were measured by QCM-D and ellipsometry, respectively. Next, we derived a set of equations starting from the Voigt model to further extract viscoelasticity of poly(OEGMA) brushes (<or=30 nm) under high-frequency vibration in contact with water. The viscosity was approximately 10(-3) N s m(-2) and the elasticity was approximately 10(5) N m(-2). Both were frequency dependent. Also discussed were other quantities such as the density (both the dry and wet film) and the working range of linear relations. These equations and quantitative information are important in advancing our understanding of ultrathin polymer brushes, which consequently promote our ability in designing functional surface coatings (i.e., in biosensor applications) and studying related interfacial phenomena.

Direct monitoring of allosteric recognition of type IIE restriction endonuclease EcoRII

EcoRII is a homodimer with two domains consisting of a DNA-binding N terminus and a catalytic C terminus and recognizes two specific sequences on DNA. It shows a relatively complicated cleavage reaction in bulk solution. After binding to either recognition site, EcoRII cleaves the other recognition site of the same DNA (cis-binding) strand and/or the recognition site of the other DNA (trans-binding) strand. Although it is difficult to separate these two reactions in bulk solution, we could simply obtain the binding and cleavage kinetics of only the cis-binding by following the frequency (mass) changes of a DNA-immobilized quartz-crystal microbalance (QCM) responding to the addition of EcoRII in aqueous solution. We obtained the maximum binding amounts (Deltam(max)), the dissociation constants (K(d)), the binding and dissociation rate constants (k(on) and k(off)), and the catalytic cleavage reaction rate constants (k(cat)) for wild-type EcoRII, the N-terminal-truncated form (EcoRII N-domain), and the mutant derivatives in its C-terminal domain (K263A and R330A). It was determined from the kinetic analyses that the N-domain, which covers the catalytic C-domain in the absence of DNA, preferentially binds to the one DNA recognition site while transforming EcoRII into an active form allosterically, and then the secondary C-domain binds to and cleaves the other recognition site of the DNA strand.

The study of beta-lactoglobulin adsorption on polyethersulfone thin film surface using QCM-D and AFM

The adsorption process of beta-lactoglobulin on the polyethersulfone-coated surface has been investigated using a quartz crystal microbalance with dissipation monitoring (QCM-D), which allowed simultaneous measurements of frequency and energy dissipation changes caused by the formation of a beta-lactoglobulin layer during the protein adsorption process. The results showed that the protein adsorption on the spin-coated polyethersulfone surface consisted of reversible and irreversible adsorption processes, and the irreversible adsorption was the principal factor to cause the permanent protein adsorption onto the polymer surface. The amount of irreversible adsorption of beta-lactoglobulin increased significantly, from 380.5 +/- 23.2 to 745.5 +/- 29.7 ng/cm2, when the concentration of beta-lactoglobulin solution varied from 0.1% to 2.0% (w/v). The pH also played an important role in the protein adsorption. When the pH of the solution varied from 7.0 to 3.0, the amount of irreversible adsorption of beta-lactoglobulin increased from 427.1 +/- 80.7 to 741.2 +/- 135.1 ng/cm2.

Employing two different quartz crystal microbalance models to study changes in viscoelastic behavior upon transformation of lipid vesicles to a bilayer on a gold surface

By analyzing the viscoelastic properties of two distinct layers, a layer of "soft" vesicles and a "rigid" bilayer, we have created a model system to permit the study of film behavior in the region of nonlinear mass and frequency change (non-Sauerbrey). The structural transformation of lipid vesicles to a bilayer is shown to be accompanied by significant changes in their physical properties. After the adsorption and saturation of intact vesicles on gold surfaces, the adsorbed vesicle layer exhibits a soft, water-rich, viscoelastic state. The AH peptide, a vesicle-destabilizing agent, is then added to trigger the formation of a much thinner (approximately 5 nm), compact, and rigid bilayer. In this study, we used the quartz crystal microbalance with dissipation technique. Large non-Sauerbrey frequency and energy dissipation changes characterize the viscoelastic nature of adsorbed intact vesicle films thicker than approximately 10 nm. Once the transformation is complete, the frequency changes along with zero energy dissipation for sufficiently thin films (t approximately 5 nm) were effectively modeled with the Sauerbrey equation. Furthermore, we checked the validity of the Voigt-Voinova model in which the quartz substrate is treated as a Voigt element, which is beyond the Sauerbrey description. The calculations treating the film as having a constant viscosity agreed well with the Voigt-Voinova model. These results were compared to calculations done using the electromechanical (EM) model, which does not require a series expansion. The Voigt-Voinova results were in excellent agreement with the EM model, providing evidence that the expansion used in their study is quite accurate.

Collapse and swelling of thermally sensitive poly(N-isopropylacrylamide) brushes monitored with a quartz crystal microbalance

Thermally sensitive poly(N-isopropylacrylamide) (PNIPAM) brushes grafted on SiO2-coated quartz crystal surface were prepared with a surface-immobilized initiator. Using quartz crystal microbalance (QCM), we investigated the collapse and swelling of the brushes in water in real time. Both frequency and dissipation of PNIPAM brushes were found to gradually change throughout a temperature range 20-38 degrees C, indicating that PNIPAM brushes undergo a continuous collapse transition in contrast with PNIPAM chains free in dilute solution exhibiting a sharp coil-to-globule transition. This result is in accordance with the previous theoretical prediction. The nonuniformity and stretching of PNIPAM brushes as well as the cooperativity between collapse and dehydration transitions are thought to be responsible for the continuity. On the other hand, a hysteresis was also observed in the cooling process. This is not only due to the intrachain and interchain interactions formed in the collapsed state but also to the nonuniform structure and stretching of the high-density brushes.

Adsorption and thermoresponsive behavior of poly(N-isopropylacrylamide-co-N,N'-cystaminebisacrylamide) thin films on gold

We describe the synthesis of thermoresponsive polymers made from N-isopropylacrylamide and varying amounts of a thiol-containing co-monomer, N,N'-cystaminebisacrylamide (P(NIPAm-co-CBAm)). Infrared spectroscopy revealed a backbone similar to that seen with pure PNIPAm. UV-vis spectroscopy showed that P(NIPAm-co-CBAm) undergoes a thermoresponsive phase transition around 32 degrees C in aqueous solution. The presence of the thiol groups enabled the polymer to adsorb onto gold surfaces. Following adsorption onto a gold surface, X-ray photoelectron spectroscopy showed a carbon/gold atomic ratio of 0.93 for a sample without CBAm and a ratio of 1.61 for a P(NIPAm-co-CBAm) sample with 0.20% CBAm. Quartz crystal microbalance (QCM) analysis showed increases in the mass of polymer adsorbed when the CBAm content in the polymer increased. The thermoresponsive behavior of the thin films on gold was investigated with contact angle and dissipative QCM analysis. Contact angles were measured for polymer films at both 25 and 60 degrees C. The largest temperature-induced alteration in the contact angle was seen with the 1.00% CBAm sample. Similarly, QCM-D results showed a significantly greater change in frequency and dissipation following a temperature change when CBAm was present than in pure NIPAm polymers.

Viscoelastic properties of fibrinogen adsorbed to the surface of biomaterials used in blood-contacting medical devices

The hemocompatibility of polymeric vascular implants is in part dependent on the propensity of fibrinogen to adsorb to the implant surface. Fibrinogen surface adsorption was measured in real time using a quartz crystal microbalance with dissipation monitoring (QCM-D). Six new, biodegradable tyrosine-derived polycarbonates were used as test surfaces. Stainless steel, poly(L-lactic acid), poly(D,L-lactide-co-glycolide), and poly(ethylene terephthalate) surfaces served as controls and provided a comparison of the test surfaces with those of commonly used biomaterials. Our study addressed the question regarding to which extent systematic variations in polymer structure can be used to optimize X-ray visibility and provide tunable degradation rates while generating protein-repellant surface properties that minimize fibrinogen adsorption. QCM-D revealed surface-dependent changes in fibrinogen layer thickness (2 to 37 nm), adsorbed wet mass (0.2 to 4.3 microg/cm2), and viscosity (0.001 to 0.005 kg/ms). While we did not find an overall correlation between surface air-water contact angle measurements and fibrinogen adsorption (R2 = 0.08), our data demonstrate that gradually increasing the poly(ethylene glycol) content within a subgroup of polymers having the same polymer backbone will lead to decreased fibrinogen adsorption. Within this subgroup of polymers, there was a strong correlation between decreasing air-water contact angles and decreasing fibrinogen adsorption (R2 = 0.95). We conclude that it is possible to minimize fibrinogen adsorption to tyrosine-derived polycarbonates while optimizing X-ray visibility and degradation rates. Some of the tyrosine-derived polycarbonates were identified as useful materials for the design of blood-contacting implants on the basis of their substantially lower levels of fibrinogen adsorption relative to the commonly used controls.

Adsorbed gels versus brushes: viscoelastic differences

It is of fundamental importance to be able to easily distinguish between the viscoelastic properties of a molecular gel (noncovalent cross-linked three-dimensional polymer structure) and a brush (polymer structure that emanates from a surface in three dimensions without cross-linking). This has relevance in biology and in designing surfaces with desired chemical and viscoelastic properties for nano and genomic technology applications. Agarose and thiol-tagged poly(ethylene glycol) were chosen as model systems, as they are known, on adsorption, to behave like a molecular gel and brush, respectively. Here, we focus on their viscoelastic differences using a quartz crystal microbalance with dissipation monitoring (QCM-D). Changes in resonance frequency and dissipation for three overtones using QCM-D were fitted with the Voigt viscoelastic model to calculate the shear viscosity and shear modulus for the adsorbed agarose gel and the PEG brush. At a surface coverage of 500 ng/cm2, the shear viscosities and shear moduli were 0.0025 +/- 0.0002 Pa-s and 2.0 +/- 0.17 x 105 Pa and 0.0010 +/- 0.0001 Pa-s and 5.0 +/- 0.3 x 104 Pa for the gel and brush, respectively. Thus, the adsorbed agarose gel layer was far more rigid than that of the covalently bound PEG brush due to its cross-linked network. Also, the diffusivity of agarose and PEG in solution was compared during adsorption onto a bare gold surface. The estimated value for the effective diffusivity of the PEG (without a thiol tag) and of the agarose gel was on the order of 10(-11) and 10(-15) m2/s, respectively. This low diffusivity for agarose supports the contention that it exists as a molecular gel with a H-bonded cross-linked network in aqueous solution. With the methods used here, it is relatively easy to distinguish the differences in viscoelastic properties between an adsorbed gel and brush.

Structure of anionic phospholipid coatings on silica by dissipative quartz crystal microbalance

The adsorption of anionic phospholipids on silica was investigated by the dissipative quartz crystal microbalance (QCM) technique. Liposomes composed of 1 mM 80:20 mol % of 1-palmitoyl-2-oleyl-sn-glycero-3-phosphatidylcholine (POPC)/phosphatidic acid, POPC/phosphatidylglycerol, or POPC/phosphatidylserine in N-(2-hydroxyethyl)piperazine-N'-(2-ethanesulfonic acid) buffer at pH 7.4 (with or without 3 mM of CaCl2) were examined. We have previously demonstrated that similar phospholipid coatings can be used in capillary electrochromatography as a stationary phase for the separation of analytes. In this work, we focus on the formation of the coatings and on the type of lipid structure formed on silica. The QCM investigation comprised qualitative results based on changes in frequency and resistance, and quantitative modeling of the obtained results. The latter was performed using the dissipative QCM, which measures the quartz crystal impedance, combined with equivalent circuit analysis. A previously developed coating and cleaning procedure for phospholipid-coated fused silica capillaries was adopted in this study, and the same silica-coated crystal was used throughout the QCM study. We will demonstrate in this work that the type of lipid structure formed on silica, that is, a rather rigid supported lipid bilayer or a viscoelastic supported vesicle layer (SVL), is highly dependent on the lipid and solvent composition. We also show for the first time that the modeling of the dissipative QCM data can be used to extract a more quantitative picture of an adsorbed SVL, because, so far, published studies have merely used the QCM data in a qualitative sense.

Hydration and Energy Dissipation Measurements of Biomolecules on a Piezoelectric Quartz Oscillator by Admittance Analyses

By using a 27-MHz piezoelectric quartz oscillator connected with a vector network analyzer, we obtained resonance frequency decreases (-DeltaFwater) and energy dissipation increases (DeltaDwater) during binding of biotinylated bovine serum albumin, biotinylated ssDNA, biotinylated dsDNA, and biotinylated pullulan to a NeutrAvidin-immobilized 27-MHz quartz crystal microbalance (QCM) plate in aqueous solution, as well as in the wet air phase (98% humidity, -DeltaFwet and DeltaDwet) and in the dry air phase (-DeltaFair and DeltaDair). -DeltaFwater indicates the total mass of the molecule, bound water, and vibrated water in aqueous solutions. -DeltaFwet indicates the total mass of the molecule and bound water. -DeltaFair simply shows the real mass of the molecule on the QCM. In terms of results, (-DeltaFwet)/(-DeltaFair) values indicated the bound water ratios per unit biomolecular mass were on the order of pullulan (2.1-2.2) > DNAs = proteins (1.4-1.6) > polystyrene (1.0). The (-DeltaFwater)/(-DeltaFair) values indicated the hydrodynamic water (bound and vibrated water) ratios per unit biomolecular mass were on the order of dsDNA (6.5) > ssDNA = pullulan (3.5-4.4) > proteins (2.4-2.5) > polystyrene (1.0). Energy dissipation parameters per unit mass in water (DeltaDwater/(-DeltaFair)) were on the order of pullulan > dsDNA > ssDNA > proteins > polystyrene. Energy dissipation in the wet and dry air phases (DeltaDwet and DeltaDair) were negligibly small, which indicates even these biomolecules act as elastic membranes in the air phase (without aqueous solution). We obtained a good linear relationship between [(-DeltaFwater)/(-DeltaFair) - 1], which is indicative of hydration and DeltaDwater/(-DeltaFair) of proteins. The aforementioned values suggest that the energy dissipation of proteins was mainly caused by hydration and that proteins themselves are elastic molecules without energy dissipation in aqueous solutions. On the contrary, plots in cases of denatured proteins, DNAs, and pullulans were relatively deviant toward the large hydration and energy dissipation from the theoretical line as perfect elastic materials, meaning that the large energy dissipation occurs because of viscoelastic properties of denatured proteins, linear DNAs, and pullulans in the water phase, in addition to energy dissipation due to the hydration of molecules. These two parameters could characterize various biomolecules with structural properties in aqueous solutions.

Influence of collagen denaturation on the nanoscale organization of adsorbed layers

Adsorption (at 37 degrees C) of type I collagen, in native and heat-denatured (30 min at 40 and 90 degrees C) forms, on polystyrene was studied using quartz crystal microbalance with energy dissipation monitoring (QCM-D), atomic force microscopy (AFM) in tapping mode and X-ray photoelectron spectroscopy (XPS). The significance of the parameters deduced from QCM-D data was examined by comparing different approaches. The adsorbed layer of native collagen has a complex organization consisting of a thin mat of molecules near the surface, in which fibrils develop depending on concentration and time, and of a thicker overlayer containing protruding molecules or bundles which modify noticeably the local viscosity. As a result of drastic denaturation, the ability of collagen to assemble into fibrils in the adsorbed phase is lost and the protrusion of molecules into the aqueous phase is much less pronounced. The adsorbed layer of denatured collagen appears essentially as a monolayer of flattened coils. At low concentration, this is easily displaced upon drying, leading to particular dewetting figures; at high concentration, aggregates add to the first layer. Moderate denaturation leads to an adsorbed phase which shows properties intermediate between those observed with native and extensively denatured collagen, regarding the ability to form fibrillar structures and the adlayer thickness and viscosity.

Polyelectrolyte nano-scaffolds for the design of layered cellular architectures

The design of in vitro multilayered cellular architectures that resemble the stratified, lattice-like structure in tissues poses a significant challenge for tissue engineering. There is currently no generally applicable methodology to design multilayered cellular constructs that mimic the structure of tissues in vivo. We report a novel and generalizable approach to create multilayered cellular constructs that addresses these issues. These in vitro constructs comprise alternating layers of cells and nano-scale biocompatible polyelectrolyte (PE) scaffolds. We apply this methodology to address two specific problems in hepatic tissue engineering: the design of in vitro liver sinusoidal structures and the critical need to increase viable cell mass in extracorporeal liver-assist devices. We assembled ultrathin polymer scaffolds on the top of a confluent monolayer of cells by the sequential deposition of oppositely charged PEs. The thickness of the PE scaffold lies in the nanometer range. The PE scaffold plays a dual role. First, it is a technique to culture hepatocytes in vitro that maintains their morphology, cytoskeletal structure, and liver-specific functions. Second, the nano-scaffold provides a cell-adhesive surface on which a second layer of cells can be cultured, resulting in layered architectures. We have used this approach to design layered three-dimensional hepatocyte-PE-hepatocyte constructs, hepatocyte-PE-endothelial cell constructs, and hepatocyte-PE-fibroblast constructs. As a result of its versatility, this approach can, in principle, be used to design layered cellular constructs of any tissue type, and therefore has potentially wide applications in tissue engineering, bioreactor devices, and in drug delivery. This methodology has the potential to generate realistic in vitro constructs of any tissue type.

Study of the Kinetics of the Pancake-to-Brush Transition of Poly(N-isopropylacrylamide) Chains

The chemical grafting of thiol-terminated poly(N-isopropylacrylamide) (HS-PNIPAM) chains to a gold surface from a solution was investigated with a quartz crystal microbalance (QCM) in real time. The frequency and energy dissipation responses revealed that short HS-PNIPAM chains exhibit three-regime kinetics of the grafting. In regimes I and II, the HS-PNIPAM chains form pancake and mushroom structures, respectively. In regime III, the chains form brushes. From regime II to regime III, the mushroom-to-brush transition occurs. For the longer HS-PNIPAM chains, because of the strong segment-surface interaction, the segments cannot desorb from the surface, and the chains do not undergo a pancake-to-brush transition.

Formation of viscoelastic protein layers on polymeric surfaces relevant to platelet adhesion

The hemocompatibility of biomaterials is highly dependent on the adhesion and activation of platelets. Surface-adsorbed fibrinogen has a dominant role in promoting platelet adhesion to artificial surfaces by binding glycoprotein IIb-IIIa (GPIIb-IIIa), the major platelet membrane receptor. Using quartz crystal microbalance with dissipation monitoring (QCM-D), we have investigated the material-dependent binding kinetics of purified GPIIb-IIIa to polymer-adsorbed fibrinogen. The following ranking of polymer-adsorbed mass (fibrinogen and GPIIb-IIIa) to test polymers could be established: poly[desaminotyrosyl-tyrosine ethyl (DTE) carbonate]/poly(lactide-co-glycolide)>poly[DTE co-5% poly(ethylene glycol) carbonate]. The QCM-D fibrinogen adsorption data were confirmed using an immunofluorescence assay. A synthetic RGD-containing peptide, but not a control peptide, inhibited GPIIb-IIIa binding to polymer-adsorbed fibrinogen, demonstrating the specificity of binding. Importantly, the binding efficiency of purified GPIIb-IIIa to polymer-adsorbed fibrinogen correlated with increased platelet adhesion in an in vitro model. Theoretical simulations using a Voight-based model provided quantitative data on the thickness and viscoelastic properties of the polymer-adsorbed protein layers. The precision of the modeling technique was limited with respect to the shear moduli values, leading to large variations. However, the other modeling parameters showed reproducible results. The thickness of both protein layers was polymer-dependent and ranged from 5 to 35 nm and the viscosity from 0.001 to 0.005 kg/ms, whereas the protein layer densities showed little differences between the test polymers. These results suggest that material-dependent changes in the thickness and viscoelastic properties of adsorbed fibrinogen-GPIIb-IIIa layers are crucial factors in the binding behavior of platelets to biomaterials.

Analysis of interpenetrating polymer networks via quartz crystal microbalance with dissipation monitoring

A quartz crystal microbalance with dissipation monitoring (QCM-D) was used to assess the physical properties of interpenetrating polymer networks (IPNs) through swelling experiments in ambient humidity and in phosphate-buffered saline (PBS), pH 7.4. The IPNs, based on acrylamide (AAm) and poly(ethylene glycol) (pEG), swell from thin, rigid films when dry (16.7 +/- 5.2 nm on Si/SiO(2)) to expanded, viscoelastic films when hydrated (107 +/- 24.2 nm on Si/SiO2). The dry IPNs could be analyzed using the Sauerbrey relationship, but for the hydrated films it was necessary to interpret QCM-D data with a Kelvin-Voigt viscoelastic model. A complex modulus |G| of 116 +/- 38.1 kPa for the swollen IPN surface on Si/SiO2 was defined by the model. The QCM-D was also employed to quantify the adsorption of human fibrinogen, a protein important in thrombus formation, onto the IPNs. Fibrinogen adsorption studies demonstrated the sensitivity of the QCM-D, as well as confirmed the nonfouling nature of the IPN surface, where less than 5 ng/cm2 of fibrinogen was adsorbed.