Formation of Ordered Nanostructures in Epoxy Thermosets: A Mechanism of Reaction-Induced Microphase Separation

Graphene oxide-based nanocomposites for outstanding eco-friendly antifungal potential against tomato phytopathogens

To obtain the collaborative antifungal potential of nanocomposites conjugated with graphene oxide (GO), a combination of GO with chitosan (CS/GO) and GO with chitosan (CS) and polyaniline (PANI/CS/GO) was carried out. The synthesized GO-nanocomposites were recognized by several techniques. Vanillin (Van.) and cinnamaldehyde (Cinn.) were loaded on the prepared nanocomposites as antioxidants through a batch adsorption process. In vitro release study of Van. and Cinn. from the nanocomposites was accomplished at pH 7 and 25°C. The antimicrobial activity of GO, CS/GO, and PANI/CS/GO was studied against tomato Fusarium oxysporum (FOL) and Pythium debaryanum (PYD) pathogens. The loaded ternary composite PANI/CS/GO exhibited the best percent of reduction against the two pathogens in vitro studies. The Greenhouse experiment revealed that seedlings' treatment by CS/GO/Van. and PANI/CS/GO/Van significantly lowered both disease index and disease incidence. The loaded CS/GO and PANI/CS/GO nanocomposites had a positive effect on lengthening shoots. Additionally, when CS/GO/Cinn., CS/GO/Van. and PANI/CS/GO/Van. were used, tomato seedlings' photosynthetic pigments dramatically increased as compared to infected control. The results show that these bio-nanocomposites can be an efficient, sustainable, nontoxic, eco-friendly, and residue-free approach for fighting fungal pathogens and improving plant growth.

Effect of Block Copolymer Self-Assembly on Phase Separation in Photopolymerizable Epoxy Blends

Directing self-assembly of photopolymerizable systems is advantageous for controlling polymer nanostructure and material properties, but developing techniques for inducing ordered structure remains challenging. In this work, well-defined diblock or random copolymers were incorporated into cationic photopolymerizable epoxy systems to investigate the impact of copolymer architecture on self-assembly and phase separated nanostructures. Copolymers consisting of poly(hydroxyethyl acrylate)-x-(butyl acrylate) were prepared using photoiniferter polymerization to control functional group placement and molecular weight/polydispersity. Prepolymer configuration and concentration induced distinctly different effects on the resin flow and photopolymerization kinetics. The diblock copolymer self-assembled into nanostructured phases within the resin matrix, whereas the random copolymer formed an isotropic mixture. Rapid photopolymerization and ambient temperature conditions during cure facilitated retention of the self-assembled phases, leading to considerably different composite morphology and thermomechanical behavior. Increased loading of the diblock copolymer induced long-range ordered cocontinuous structures. Even with nearly identical prepolymer composition, controlled nanophase separation resulted in significantly enhanced tensile properties relative to those of the isotropic system. This work demonstrates that controlling phase separation with a block copolymer architecture allows access to nanostructured photopolymers with unique and enhanced properties.

Toughening of epoxy thermosets by self-assembled nanostructures of amphiphilic comb-like random copolymers

Amphiphilic comb-like random copolymers synthesized from poly(ethylene glycol) methyl ether methacrylate (PEGMMA) and stearyl methacrylate (SMA) with PEGMMA contents ranging between 30 wt% and 25 wt% were demonstrated to self-assemble into various well-defined nanostructures, including spherical micelles, wormlike micelles, and vesicle-like nanodomains, in anhydride-cured epoxy thermosets. In addition, the polymer blends of the comb-like random copolymer and poly(stearyl methacrylate) were prepared and incorporated into epoxy thermosets to form irregularly shaped nanodomains. Our research findings indicate that both the comb-like random copolymers and polymer blends are suitable as toughening modifiers for epoxy. When added at a concentration of 5 wt%, both types of modifiers lead to substantial improvements in the tensile toughness (>289%) and fracture toughness of epoxy thermosets, with minor reductions in their elastic modulus (<16%) and glass transition temperature (<6.1 °C). The fracture toughness evaluated in terms of the critical stress intensity factor (KIC) and the strain energy release rate (GIC) increased by more than 67% and 131% for the modified epoxy thermosets containing comb-like random copolymers.

Nanostructuring Biobased Epoxy Resin with PEO-PPO-PEO Block Copolymer

A biobased diglycidyl ether of vanillin (DGEVA) epoxy resin was nanostructured by poly(ethylene oxide-b-propylene oxide-b-ethylene oxide) (PEO-PPO-PEO) triblock copolymer. Due to the miscibility/immiscibility properties of the triblock copolymer in DGEVA resin, different morphologies were obtained depending on the triblock copolymer amount. A hexagonally packed cylinder morphology was kept until reaching 30 wt% of PEO-PPO-PEO content, while a more complex three-phase morphology was obtained for 50 wt%, in which large worm-like PPO domains appear surrounded by two different phases, one of them rich in PEO and another phase rich in cured DGEVA. UV-vis measurements show that the transmittance is reduced with the increase in triblock copolymer content, especially at 50 wt%, probably due to the presence of PEO crystals detected by calorimetry.

Long PEO-based nanoribbons generated in a polystyrene matrix through reaction-induced microphase separation followed by a fast crystallization process

A dispersion of elongated nanostructures with a high aspect ratio in polymer matrices has been reported to provide a material with valuable properties such as mechanical strength, barrier effect and shape memory, among others. In this study, we show the procedure to achieve a distribution of elongated crystalline nanodomains in a PS matrix employing the self-assembly of amphiphilic block copolymers (BCP). The selected BCP was polystyrene-block-polyethylene oxide (PS-b-PEO). It was dissolved at 10 wt% in a styrene (St) monomer and the blend was slowly photopolymerized over four days at room temperature, until the reaction was arrested by vitrification. This blend was initially homogeneous and nanostructuration took place in an early stage of the polymerization as a result of the microphase separation (MS) of PEO blocks. Due to its high tendency to crystallize, demixed PEO blocks crystallized almost concomitantly with MS triggering the growing of the nanostructures. Thus, the time window between the onset of crystallization and the vitrification of the matrix was almost four days, allowing all micelles to have the opportunity to couple to a growing nanostructure. As a result, a population of nanoribbons with average lengths surpassing 10 μm dispersed in a PS matrix was obtained. It was demonstrated that these ribbon-like nanostructures are preserved as long as the heating temperature is located below the Tg of the matrix. If the material is heated above this temperature, softening of the matrix allows the breakup of the molten PEO nanoribbons due to Plateau-Rayleigh instability.

Reaction-induced phase transitions with block copolymers in solution and bulk

Reaction-induced phase transitions use chemical reactions to drive macromolecular organisation and self-assembly. This review highlights significant and recent advancements in this burgeoning field.

Thermoreversible Polymer Gels in DMF Formed from Charge- and Crystallization-Induced Assembly

Polymer organogels formed through dynamic interactions are interesting for various applications. The fabrication of polymer organogels in polar solvents through ionic interaction is rare, although such organogels in non-polar organic solvents have been well studied. Herein, polymer organogels in a polar solvent N,N-dimethyl formamide (DMF) were fabricated from a triblock copolymer, poly(4-vinyl pyridine)-block-poly(ethylene glycol)-block-poly(4-vinyl pyridine) (4VPm-EGn-4VPm), and a fluorinated surfactant, perfluorooctanoic acid (PFOA), and their microphase separation and properties were studied. Ordered microphase separation and the crystalline structures were revealed by small-angle X-ray scattering (SAXS) and wide-angle X-ray scattering (WAXS), respectively. All the 4VPm-EGn-4VPm/PFOA organogels are sensitive to temperature, and the ratio of PFOA to pyridine groups reversibly. The polymer organogels are also responsive to triethylamine and triethylammonium acetate.

Investigation of Azobenzene Photoisomerization Effect on Morphologies and Properties of Nanostructured Thermosets Involving Epoxy and a Diblock Copolymer

This work highlights the effect of azobenzene photoisomerization on the morphologies and properties of the nanostructured thermosets involving epoxy and a diblock copolymer. First, a diblock copolymer composed of poly(ethylene oxide) (PEO) and poly(6-(4-(4-cyanophenylazo)phenoxy)hexyl methacrylate) (PCPHM) was synthesized, and this diblock copolymer was composed of an epoxy-philic block (i.e., PEO) and an azobenzene moiety-beating block (viz., PCPHM). This diblock copolymer was introduced into epoxy to obtain the nanostructured thermosets via reaction-induced microphase separation approach. To control the configuration of azobenzene moieties of the PCPHM block, the curing reactions were performed in the absence and/or presence of ultraviolet (UV) irradiation, respectively. It was found that, without UV irradiation, the PCPHM microdomains were generated with the trans isomers of azobenzene. Under UV irradiation, however, the PCPHM microdomains were formed with the cis configuration of azobenzene moieties. The ultraviolet-visible light (UV-vis) spectroscopy showed that the trans and cis configurations of azobenzene moieties were significantly fixed with the occurrence of curing reactions. The photoluminescent measurements showed that the nanostructured thermosets with trans-azobenzene moieties can emit fluorescence, which was in sharp contrast to those with cis-azobenzene moieties. The results of small-angle X-ray and atomic force microscopy showed that the nanostructured thermosets with trans and cis isomers of azobenzene moieties had quite different morphologies. It was found that the sizes of the PCPHM microdomains with cis configuration of azobenzene moieties were significantly larger than those with trans configuration. The difference in configuration of azobenzene moieties also resulted in the difference in glass-transition temperatures and dielectric properties of the materials. The results suggest a new approach to modulate the morphologies and physical properties of the nanostructured thermosets by means of photoisomerization of azobenzene moieties.

Fluorescence Enhancement Induced by Curing Reaction in Nanostructured Epoxy Thermosets Containing a Diblock Copolymer

In this work, a novel curing-induced fluorescence (FL) enhancement phenomenon in the nanostructuring process of epoxy thermosets was investigated. Toward this end, a diblock copolymer composed of poly(ethylene oxide) and poly(((4-vinylphenyl)ethene-1,1,2-triyl)tribenzene) (PTPEE) blocks was introduced into epoxy thermosets. Before curing reaction, the mixtures of epoxy precursors with the diblock copolymer only emitted feeble FL under ultra-visible (UV) irradiation. However, photoluminescence was significantly enhanced after the curing reaction was carried out. It was found that the novel FL enhancement phenomenon resulted from the aggregation-induced emission behavior of PTPEE blocks, which was triggered by curing reaction. In the nanostructured thermosets, the fluorophore blocks (viz. PTPEE) of this diblock copolymer were segregated into aggregates, that is, a reaction-induced microphase separation occurred. Owing to the generation of PTPEE microdomains, the epoxy nanocomposites significantly displayed the enhanced dielectric constants due to the promoted contribution from electron polarizations via π-π conjugation in the materials.

Core-crystalline nanoribbons of controlled length via diffusion-limited colloid aggregation

It has been previously reported that poly(ethylene) (PE)-based block copolymers self-assemble in certain thermosetting matrices to form a dispersion of one-dimensional (1D) nanoribbons. Such materials exhibit exceptional properties that originate from the high aspect ratio of the elongated nano-objects. However, the ability to prepare 1D assemblies with well-controlled dimensions is limited and represents a key challenge. Here, we demonstrate that the length of ribbon-like nanostructures can be precisely controlled by regulating the mobility of the matrix during crystallization of the core-forming PE block. The selected system to prove this concept was a poly(ethylene-block-ethylene oxide) (PE-b-PEO) block copolymer in an epoxy monomer based on diglycidyl ether of bisphenol A (DGEBA). The system was activated with a dual thermal- and photo-curing system, which allowed us to initiate the epoxy polymerization at 120 °C until a certain degree of conversion, stop the reaction by cooling to induce crystallization and micellar elongation, and then continue the polymerization at room temperature by visible-light irradiation. In this way, crystallization of PE blocks took place in a matrix whose mobility was regulated by the degree of conversion reached at 120 °C. The mechanism of micellar elongation was conceptualized as a diffusion-limited colloid aggregation process which was induced by crystallization of PE cores. This assertion was supported by the evidence obtained from in situ small-angle X-ray scattering (SAXS), in combination with differential scanning calorimetry (DSC) and transmission electron microscopy (TEM).

Tensile Properties, Fracture Mechanics Properties and Toughening Mechanisms of Epoxy Systems Modified with Soft Block Copolymers, Rigid TiO2 Nanoparticles and Their Hybrids

The effect of the hybridization of a triblock copolymer and a rigid TiO2 nanofiller on the tensile, fracture mechanics and thermo-mechanical properties of bisphenol F based epoxy resin were studied. The self-assembling block copolymer, constituted of a center block of poly (butyl acrylate) and two side blocks of poly (methyl) methacrylate-co-polar co-monomer was used as a soft filler, and TiO2 nanoparticles were employed as rigid modifiers. Toughening solely by block copolymers (BCP’s) led to the highest fracture toughness and fracture energy in the study, KIc = 2.18 MPa·m1/2 and GIc = 1.58 kJ/m2. This corresponds to a 4- and 16-fold improvement, respectively, over the neat reference epoxy system. However, a reduction of 15% of the tensile strength was observed. The hybrid nanocomposites, containing the same absolute amounts of modifiers, showed a maximum value of KIc = 1.72 MPa·m1/2 and GIc = 0.90 kJ/m2. Yet, only a minor reduction of 4% of the tensile strength was observed. The fracture toughness and fracture energy were co-related to the plastic zone size for all the modified systems. Finally, the analysis of the fracture surfaces revealed the toughening mechanisms of the nanocomposites.

Synthesis of well-defined PCL-b-PnBA-b-PMMA ABC-type triblock copolymers: toward the construction of nanostructures in epoxy thermosets

A novel PCL-b-PnBA-b-PMMA was designed and applied to construct ordered nanostructures within epoxy thermosets.

Organic-Inorganic Nanocomposites via Self-Assembly of an Amphiphilic Triblock Copolymer Bearing a Poly(butadiene-g-POSS) Subchain in Epoxy Thermosets: Morphologies, Surface Hydrophobicity, and Dielectric Properties

Organic-inorganic nanocomposites composed of polyhedral oligomeric silsesquioxane (POSS) and epoxy resin were prepared via self-assembly of an amphiphilic triblock copolymer bearing a poly(POSS) midblock in epoxy thermosets. First, this organic-inorganic amphiphilic triblock copolymer was synthesized via hydrosilylation of heptaphenylhydro POSS with an existing triblock copolymer containing a short polybutadiene midblock. It was found that this novel amphiphilic block copolymer can self-assemble into nanophases in epoxy thermosets. In the presence of preformed nanophases, the curing reaction was performed, and the organic-inorganic nanocomposites containing poly(POSS) microdomains were thus obtained. Compared with plain epoxy, the as-obtained thermosets exhibited enhanced surface hydrophobicity; the enhanced surface hydrophobicity is attributed to enrichment of the POSS component at the surface of the materials. Owing to the formation of poly(POSS) microdomains, the dielectric constants of the materials significantly reduced, whereas the dielectric loss remained almost unchanged.

The self-assembly mechanism of tetra-peptides from the motif of β-amyloid peptides: a combined coarse-grained and all-atom molecular dynamics simulation

Understanding the self-assembly mechanisms of tetra-peptides from Aβ-peptides into different nanostructures.

Toughening of photo-curable polymer networks: a review

This review surveys relevant scientific papers and patents on the development of crosslinked epoxies and also photo-curable polymers based on multifunctional acrylates with improved toughness.

Evolution of morphologies of a PE-b-PEO block copolymer in an epoxy solvent induced by polymerization followed by crystallization-driven self-assembly of PE blocks during cooling

This work reports how to generate complex nanostructures in an epoxy network by combining polymerization-induced nanostructuration with crystallization-driven self-assembly of a semicrystalline block copolymer.

High porosity microspheres with functional groups synthesized by thiol–yne click suspension polymerization

We employed a combination of thiol–yne click polymerization and suspension polymerization for the synthesis of porous epoxy-functionalized polymeric microspheres.

Enhancing mechanical performance of epoxy thermosets via designing a block copolymer to self-organize into “core–shell” nanostructure

A rigid-flexible amphiphilic pentablock copolymer, polystyrene-block-poly(ε-caprolactone)-block-polydimethylsiloxane-block-poly(ε-caprolactone)-block-polystyrene (PS-PCL-PDMS-PCL-PS, SLDLS), was designed.