Sweet Solution for Sticky Problems: Chemoreological Design of Self-Adhesive Gel Materials Derived From Lipid Biofeedstocks and Adhesion Tailoring via Incorporation of Isosorbide

Room-Temperature Self-Healing and Recyclable Self-Crosslinked Isosorbide-Based Adhesive Bioelastomer

Recently, renewable bio-based materials have received more and more attention due to environmental issues such as global warming and ecosystem destruction. In the present work, a series of isosorbide-based bioelastomers poly(isosorbide carbonate-co-butanediol aliphatic esters)s (PICBAs) are synthesized by a facile and economical two-step melt polycondensation. Due to the slightly self-crosslinking reaction of isosorbide, PICBAs exhibit excellent tensile strength and self-healing ability, the mechanical properties of PICBAs can recover over 95% after 48 h under room temperature. In addition, PICBAs can stick different substances, such as glass, rubber, plastic, and stones, and show better adhesive performance than 3M commercially available double-sided tape. Consequently, isosorbide-based bioelastomers PICBAs are of great potential to be used as environmentally friendly pressure-sensitive adhesives (PSA) in the future.

Concentration-induced spontaneous polymerization of protic ionic liquids for efficient in situ adhesion

The advancement of contemporary adhesives is often limited by the balancing act between cohesion and interfacial adhesion strength. This study explores an approach to overcome this trade-off by utilizing the spontaneous polymerization of a protic ionic liquid-based monomer obtained through the neutralization of 2-acrylamide-2-methyl propane sulfonic acid and hydroxylamine. The initiator-free polymerization process is carried out through a gradual increase in monomer concentration in aqueous solutions caused by solvent evaporation upon heating, which results in the in-situ formation of a tough and thin adhesive layer with a highly entangled polymeric network and an intimate interface contact between the adhesive and substrate. The abundance of internal and external non-covalent interactions also contributes to both cohesion and interfacial adhesion. Consequently, the produced protic poly(ionic liquid)s exhibit considerable adhesion strength on a variety of substrates. This method also allows for the creation of advanced adhesive composites with electrical conductivity or visualized sensing functionality by incorporating commercially available fillers into the ionic liquid adhesive. This study provides a strategy for creating high-performance ionic liquid-based adhesives and highlights the importance of in-situ polymerization for constructing adhesive composites.

Janus mucosal dressing with a tough and adhesive hydrogel based on synergistic effects of gelatin, polydopamine, and nano-clay

There are many problems and challenges related to the treatment of highly prevalent oral mucosal diseases and oral drug delivery because of a large amount of saliva present in the oral cavity, the accompanying oral movements, and unconscious swallowing in the mouth. Therefore, an ideal oral dressing should possess stable adhesion and superior tough strength in the oral cavity. However, this fundamental requirement greatly limits the use of synthetic adhesive dressings for oral dressings. Here, we developed a mussel-inspired Janus gelatin-polydopamine-nano-clay (GPC) hydrogel with controlled adhesion and toughness through the synergistic physical and chemical interaction of gelatin (Gel), nano-clay, and dopamine (DA). The hydrogel not only exhibits strong wet adhesion force (63 kPa) but also has high toughness (1026 ± 100 J m^-3). Interfacial adhesion of hydrogels is achieved by modulating the interaction of catechol groups of the hydrogel with specific functional groups (e.g., NH₂, SH, OH, and COOH) on the tissue surface. The matrix dissipation of the hydrogel is regulated by physical crosslinking of gelatin, chemical crosslinking of gelatin with polydopamine (Michael addition and Schiff base formation), and nano-clay-induced constraint of the molecular chain. In addition, the GPC hydrogel shows high cell affinity and favors cell adhesion and proliferation. The hydrogel's instant and strong mucoadhesive properties provide a long-lasting therapeutic effect of the drug, thereby enhancing the healing of oral ulcers. Therefore, mussel-inspired wet-adhesion Janus GPC hydrogels can be used as a platform for mucosal dressing and drug delivery systems. STATEMENT OF SIGNIFICANCE: It is a great challenge to treat oral mucosal diseases due to the large amount of saliva present in the oral cavity, the accompanying oral movements, unconscious swallowing, and flushing of drugs in the mouth. To overcome the significant limitations of clinical bioadhesives, such as weakness, toxicity, and poor usage, in the present study, we developed a simple method through the synergistic effects of gelatin, polydopamine, and nano-clay to prepare an optimal mucosal dressing (Janus GPC) that integrates Janus, adhesion, toughness, and drug release property. It fits effectively in the mouth, resists saliva flushing and oral movements, provides oral drug delivery, and reduces patient discomfort. The Janus GPC adhesive hydrogels have great commercial potential to support further the development of innovative therapies for oral mucosal diseases.

Biodegradable copolyesters based on a “soft” isohexide building block with tunable viscoelasticity and self-adhesiveness

PBIA copolyesters synthesised using a novel glycosylated monomer (IIDMC) have faster degradation and tunable self-adhesiveness.

Influence of UV Polymerization Curing Conditions on Performance of Acrylic Pressure Sensitive Adhesives

Acrylic pressure sensitive adhesives (PSAs) were prepared by UV polymerization under varying curing conditions of both fast and slow curing, employing high- and low-intensity UV radiation, respectively. The influences of curing conditions and isobornyl acrylate (IBOA) content on PSA performance were comprehensively investigated by measurement of their rheological, thermal, and adhesive properties. In particular, rheological characterization was accomplished by several analytical methods, such as in situ UV rheology, frequency sweep, stress relaxation, and temperature ramp tests, to understand the effect of the UV curing process and IBOA content on the viscoelastic behavior of acrylic PSAs. The slow-cured samples were observed to form more tightly crosslinked networks compared to the fast-cured. On the other hand, at high loading levels of IBOA, in the case of slow curing, the sample exhibited a contrasting trend, having the shortest stress relaxation time and the highest energy dissipation; this was due to molecular chain scission occurring in the crosslinked polymer during UV polymerization. Consequently, we successfully demonstrated the influence of monomer composition of acrylic PSAs, and that of curing conditions employed in UV polymerization. This study provides valuable insights for the development of crosslinked polymer networks of acrylic PSAs for flexible display applications.

Bio-based and Degradable Block Polyester Pressure-Sensitive Adhesives

A new class of bio-based fully degradable block polyesters are pressure-sensitive adhesives. Bio-derived monomers are efficiently polymerized to make block polyesters with controlled compositions. They show moderate to high peel adhesions (4-13 N cm-1 ) and controllable storage and loss moduli, and they are removed by adhesive failure. Their properties compare favorably with commercial adhesives or bio-based polyester formulations but without the need for tackifier or additives.

Effect of Uniformly Applied Force and Molecular Characteristics of a Polymer Chain on Its Adhesion to Graphene Substrates

The force-induced desorption of a polymer chain from a graphene substrate is studied with molecular dynamics (MD). A critical force needs to be exceeded before detachment of the polymer from the substrate. It is found that for a chain to exhibit good adhesive properties the chain configuration should consist of fibrils-elongated, aligned sections of polymers and cavities which dissipate the applied energy. A fibrillation index is defined to quantify the quality of fibrils. We focus on the molecular properties of the polymer chain, which can lead to large amounts of fibrillation, and find that both strong attraction between the polymer and substrate and good solvency conditions are important conditions for this. We also vary the stiffness of the chain and find that for less stiff chains a plateau in the stress-strain curve gives rise to good adhesion however for very stiff chains there is limited elongation of the chain but the chain can still exhibit good fibrillation by a lamella-like rearrangement. Finally, it is found that the detachment time, t, of a polymer from the adsorbed substrate is inversely proportional to force, F (i.e., t ∝ F(-γ)), where exponent γ depends on the solvent quality, polymer-substrate attraction, and chain stiffness.

High thermal stability and high tensile strength terpolyester nanofibers containing biobased monomer: fabrication and characterization

Novel nanofibers of a highly heat-resistive biobased terpolyester of isosorbide (ISB), ethylene glycol, 1,4-cyclohexane dimethanol and terephthalic acid (PEICT) were fabricated using electrospinning and their properties were characterized.

Copolymers from epoxidized soybean oil and lactic acid oligomers for pressure-sensitive adhesives

Corn based lactic acid oligomers and soybean based epoxidized oil were copolymerized under UV irradiation for biobased pressure-sensitive adhesives (PSA).

Synthesis and characterization of acrylic polyols and polymers from soybean oils for pressure-sensitive adhesives

Soybean oil based acrylic polyol with modulated acrylate and hydroxyl functionalities was polymerized under UV radiation for biobased pressure-sensitive adhesives (PSA).

High capacity, easy release adhesives from renewable materials

Reversible adhesives composed of renewable materials are presented which achieve high force capacities (810 N) while maintaining easy release (∼ 0.25 N) and reusability. These simple, non-tacky adhesives consist of natural rubber impregnated into stiff natural fiber fabrics, including cotton, hemp, and jute. This versatile approach enables a clear method for designs of environmentally-responsible, reversible adhesives for a wide variety of applications.