Influence of Annealing on Microstructure and Mechanical Properties of Isotactic Polypropylene with β-Phase Nucleating Agent

Direct 3D Printing of Recycled PET/PP Granules by Shear Screw Extrusion

This article introduces a one-step extrusion-based fused deposition modeling (FDM) approach for the challenging separation of polypropylene (PP) and polyethylene terephthalate (PET) during recycling. A shear screw printer (SSP) with shear elements was designed, and it was compared to a conventional single-screw printer (CSP) to investigate the differences in print stability, degradation levels, tensile performance, molecular orientation, and crystallization when preparing recycled PP and recycled PET blends. Although the retention effect of the SSP screw slightly increases the degradation of the blended rPP/rPET, the strong shear (2.6 × 104 s-1) applied near the extrusion exit improves the blending efficiency. The SSP also enhances molecular orientation, modulus of the parts, and reduces performance fluctuations. Additionally, the SSP has the potential to simplify the recycling process, enabling the transformation of blended recycled materials into products with just one melt process.

The Structural Evolution of β-to-α Phase Transition in the Annealing Process of Poly(3-hydroxybutyrate-co-3-hydroxyvalerate)

In this study, the structural and property changes induced in the highly ordered structure of preoriented poly(3-hydroxybutyrate-co-3-hydroxyvalerate) PHBV films containing the β-form during annealing were investigated. The transformation of the β-form was investigated by means of in situ wide-angle X-ray diffraction (WAXD) using synchrotron X-rays. The comparison of PHBV films with the β-form before and after annealing was performed using small-angle X-ray scattering (SAXS), scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). The evolution mechanism of β-crystal transformation was elucidated. It was revealed that most of the highly oriented β-form directly transforms into the highly oriented α-form, and there might be two kinds of transformations: (1) The β-crystalline bundles may be transformed one by one rather than one part by one part during annealing before a certain annealing time. (2) The β-crystalline bundles crack or the molecular chains of the β-form are separated from the lateral side after annealing after a certain annealing time. A model to describe the microstructural evolution of the ordered structure during annealing was established based on the results obtained.

The Influence of Glass Fiber/Glass Fiber Powder with β-Nucleating Agent on the Properties of Polypropylene

Glass fiber-reinforced polypropylene (PP/GF) has been widely used due to its high stiffness, but for some applications that need low-module characteristics, PP/GF will have limitations due to its lower toughness, so it is necessary to develop glass fiber-modified polypropylene with good stiffness–toughness balance performance. In this study, two average length glass fibers (4.5 mm and 12 mm) and glass fiber powder, combined with β-nucleating agent, were used to investigate the effects on the crystallization and mechanical properties of polypropylene. The results show that compared with glass fiber, glass fiber powder cooperates with β-nucleating agent reinforced polypropylene composite showed good stiffness–toughness balance performance, and β-crystals were found in the composite measured by Differential Scanning Calorimetry (DSC), the presence of β-crystals can improve the toughness of the composite.

The Influence of Melt Status and Beta-Nucleation Agent Distribution on the Crystallization of Isotactic Polypropylene

Although being investigated extensively in past decades, the factors affecting β-crystallization in β-nucleating agent/iPP composites have not been identified completely. In this study, β-crystallization in mesomorphic melt and free melt...

Effects of Solid-State Stretching on Microstructure Evolution and Physical Properties of Isotactic Polypropylene Sheets

The microstructure evolution of an isotactic polypropylene (iPP) sheet during solid-state stretching was studied. The transition of the spherulites—cylindrites was evaluated using in-situ two-dimensional wide-angle and small-angle X-ray scattering methods. The crystallinity of stretched iPP sheets was characterized by differential scanning calorimetry. The crystal morphology was observed by means of scanning electron microscopy. It was found that the differences of crystal microstructure of the iPP sheet depended on the stretching strain, which promoted the orientation of molecular chains. Amorphous molecular chains in the spherulites oriented and formed into a mesophase near the yield point, and the partially ordered mesophase was further stretched to form an oriented cylindrite structure after the yield point. The highest relative content of cylindrites appeared at 15% strain. Notably, as the amorphous phase embedded into the lamellae layer, the crystal size decreased with the increase of strain, which indicated that the crystallinity of the stretched iPP sheet was much higher than that of unstretched iPP sheet. The induced cylindrites structure played a more important role in improving the mechanical properties and heat resistance of iPP sheets. Compared with the unstretched iPP sheets, the tensile strength increased by 28%, the notch impact toughness significantly increased by 78%, and the vicat softening point increased from 104 to 112 °C.