In Situ Deposition of PLGA Nanofibers via Solution Blow Spinning

Nonwoven fiber meshes for oxygen sensing

Accurate oxygen sensing and cost-effective fabrication are crucial for the adoption of wearable devices inside and outside the clinical setting. Here we introduce a simple strategy to create nonwoven polymeric fibrous mats for a notable contribution towards addressing this need. Although morphological manipulation of polymers for cell culture proliferation is commonplace, especially in the field of regenerative medicine, non-woven structures have not been used for oxygen sensing. We used an airbrush spraying, i.e. solution blowing, to obtain nonwoven fiber meshes embedded with a phosphorescent dye. The fibers serve as a polymer host for the phosphorescent dye and are shown to be non-cytotoxic. Different composite fibrous meshes were prepared and favorable mechanical and oxygen-sensing properties were demonstrated. A Young's modulus of 9.8 MPa was achieved and the maximum oxygen sensitivity improved by a factor of ∼2.9 compared to simple drop cast film. The fibers were also coated with silicone rubbers to produce mechanically robust sensing films. This reduced the sensing performance but improved flexibility and mechanical properties. Lastly, we are able to capture oxygen concentration maps via colorimetry using a smartphone camera, which should offer unique advantages in wider usage. Overall, the introduced composite fiber meshes show a potential to significantly improve cell cultures and healthcare monitoring via absolute oxygen sensing.

Drug eluting protein and polysaccharides-based biofunctionalized fabric textiles- pioneering a new frontier in tissue engineering: An extensive review

In the ever-evolving landscape of tissue engineering, medicated biotextiles have emerged as a game-changer. These remarkable textiles have garnered significant attention for their ability to craft tissue scaffolds that closely mimic the properties of natural tissues. This comprehensive review delves into the realm of medicated protein and polysaccharide-based biotextiles, exploring a diverse array of fabric materials. We unravel the intricate web of fabrication methods, ranging from weft/warp knitting to plain/stain weaving and braiding, each lending its unique touch to the world of biotextiles creation. Fibre production techniques, such as melt spinning, wet/gel spinning, and multicomponent spinning, are demystified to shed light on the magic behind these ground-breaking textiles. The biotextiles thus crafted exhibit exceptional physical and chemical properties that hold immense promise in the field of tissue engineering (TE). Our review underscores the myriad applications of drug-eluting protein and polysaccharide-based textiles, including TE, tissue repair, regeneration, and wound healing. Additionally, we delve into commercially available products that harness the potential of medicated biotextiles, paving the way for a brighter future in healthcare and regenerative medicine. Step into the world of innovation with medicated biotextiles-where science meets the art of healing.

Fish Scale Gelatin Nanofibers with Helichrysum italicum and Lavandula latifolia Essential Oils for Bioactive Wound-Healing Dressings

Essential oils are valuable alternatives to synthetic antibiotics that have the potential to avoid the pathogen resistance side effects generated by leather. Helichrysum italicum and Lavandula latifolia essential oils combined with fish scale gelatin were electrospun using a coaxial technique to design new bioactive materials for skin wound dressings fabrication. Fish scale gelatins were extracted from carp fish scales using two variants of the same method, with and without ethylenediaminetetraacetic acid (EDTA). Both variants showed very good electrospinning properties when dissolved in acetic acid solvent. Fish scale gelatin nanofibers with Helichrysum italicum and Lavandula latifolia essential oil emulsions ensured low microbial load (under 100 CFU/g of total number of aerobic microorganisms and total number of yeasts and filamentous fungi) and the absence of Staphylococcus aureus ATCC 6538, Escherichia coli ATCC 10536, and Candida albicans ATCC 1023 as compared to fish scale gelatin without essential oils, which recommends them for pharmaceutical or topical applications. A scratch-test performed on human dermal fibroblasts proved that the biomaterials contributing to the wound healing process included fish scale gelatin nanofibers without EDTA (0.5% and 1%), fish scale gelatin nanofibers without EDTA and Lavandula latifolia essential oil emulsion (1%), fish scale gelatin nanofibers with EDTA (0.6%), and fish scale gelatin nanofibers with EDTA with Helichrysum italicum essential oil emulsion (1% and 2%).

Fibrous Structures Produced Using the Solution Blow-Spinning Technique for Advanced Air Filtration Process

This study proposes utilising the solution blow-spinning process (SBS) for manufacturing a biodegradable filtration structure that ensures high efficiency of particle filtration with an acceptable pressure drop. The concept of multi-layer filters was applied during the design of filters. Polylactic acid (PLA) was used to produce various layers, which may be mixed in different sequences, building structures with varying filtration properties. Changing the process parameters, one can create layers with diverse average fibre diameters and thicknesses. It enables the design and creation of optimal filtration materials prepared for aerosol particle filtration. The structures were numerically modelled using the lattice Boltzmann approach to obtain detailed production guidelines using the blow-spinning technique. The advantage of this method is the ability to blow fibres with diameters in the nanoscale, applying relatively simple and cost-effective equipment. For tested PLA solutions, i.e., 6% and 10%, the mean fibre diameter decreases as the concentration decreases. Therefore, the overall filtering efficiency decreases as the concentration of the used solution increases. The produced multi-layer filters have 96% overall filtration efficiency for particles ranging from 0.26 to 16.60 micrometres with a pressure drop of less than 160 Pa. Obtained results are auspicious and are a step in producing efficient, biodegradable air filters.

Multifunctional bilayer membranes composed of poly(lactic acid), beta-chitin whiskers and silver nanoparticles for wound dressing applications

Nanomaterial-based wound dressings have been extensively studied for the treatment of both minor and life-threatening tissue injuries. These wound dressings must possess several crucial characteristics, such as tissue compatibility, non-toxicity, appropriate biodegradability to facilitate wound healing, effective antibacterial activity to prevent infection, and adequate physical and mechanical strength to withstand repetitive dynamic forces that could potentially disrupt the healing process. Nevertheless, the development of nanostructured wound dressings that incorporate various functional micro- and nanomaterials in distinct architectures, each serving specific purposes, presents significant challenges. In this study, we successfully developed a novel multifunctional wound dressing based on poly(lactic acid) (PLA) fibrous membranes produced by solution-blow spinning (SBS) and electrospinning. The PLA-based membranes underwent surface modifications aimed at tailoring their properties for utilization as effective wound dressing platforms. Initially, beta-chitin whiskers were deposited onto the membrane surface through filtration, imparting hydrophilic character. Afterward, silver nanoparticles (AgNPs) were incorporated onto the beta-chitin layer using a spray deposition method, resulting in platforms with antimicrobial properties against both Staphylococcus aureus and Escherichia coli. Cytotoxicity studies demonstrated the biocompatibility of the membranes with the neonatal human dermal fibroblast (HDFn) cell line. Moreover, bilayer membranes exhibited a high surface area and porosity (> 80%), remarkable stability in aqueous media, and favorable mechanical properties, making them promising candidates for application as multifunctional wound dressings.

Rapid production of silver nanofibers using a self-reducing solution

Silver nanofibers (Ag NFs) have gained considerable attention because of their high transmittance resulting from the size effect, excellent electrical conductivity, and mechanical properties. However, synthesizing high-quality Ag NFs remains a challenge. This paper reports a novel self-reducing solution that contains platinum nanoparticles for the rapid production of Ag NFs. The method involves generating the precursor NFs and heating them in air, which reduces silver nitrate to Ag NFs within a few minutes. The as-prepared solution is characterized by its simple preparation, cost-effectiveness, and broad applicability. Additionally, the use of high-pressure airflow to directly spin the solution and a complete self-reduction system that does not depend on external conditions broadens the application prospects of the as-developed solution. Furthermore, we provide insights into the self-reduction mechanism and guidance on the preparation of self-reducing solutions.

Advances in Biomedical Applications of Solution Blow Spinning

In recent years, Solution Blow Spinning (SBS) has emerged as a new technology for the production of polymeric, nanocomposite, and ceramic materials in the form of nano and microfibers, with similar features to those achieved by other procedures. The advantages of SBS over other spinning methods are the fast generation of fibers and the simplicity of the experimental setup that opens up the possibility of their on-site production. While producing a large number of nanofibers in a short time is a crucial factor in large-scale manufacturing, in situ generation, for example, in the form of sprayable, multifunctional dressings, capable of releasing embedded active agents on wounded tissue, or their use in operating rooms to prevent hemostasis during surgical interventions, open a wide range of possibilities. The interest in this spinning technology is evident from the growing number of patents issued and articles published over the last few years. Our focus in this review is on the biomedicine-oriented applications of SBS for the production of nanofibers based on the collection of the most relevant scientific papers published to date. Drug delivery, 3D culturing, regenerative medicine, and fabrication of biosensors are some of the areas in which SBS has been explored, most frequently at the proof-of-concept level. The promising results obtained demonstrate the potential of this technology in the biomedical and pharmaceutical fields.

Instantaneous Formation of Silk Protein Aerosols and Fibers with a Portable Spray Device Under Ambient Conditions

A variety of artificial silk spinning approaches have been attempted to mimic the natural spinning process found in silkworms and spiders, yet instantaneous silk fiber formation with hierarchical structure under physiological and ambient conditions without post-treatment procedures remains unaddressed. Here, we report a new strategy to fabricate silk protein-based aerosols and silk fibers instantaneously (< 1 s) in situ using a simple, portable, spray device, avoiding complicated and costly advanced manufacturing techniques. The key to success is the instantaneous conformational transition of silk fibroin from random coil to β-sheet right before spraying by mixing silk and polyethylene glycol (PEG) solutions in the spray device, allowing aerosols and silk fibers to be sprayed in situ, with further control achieved via the molecular weight of silk. The spinning process of the spray device is based on the use of green solvents, i.e., all steps of instant conformational transition of silk fibroin are carried out in aqueous conditions or with buffers at ambient conditions, in combination with shear and elongational flow caused by the hydraulic pressure generated in the spray container. The system supports a portable and user-friendly system that could be used for drug delivery carriers, wound coating materials and rapid silk fiber conformal coatings on surfaces.

High-Speed Centrifugal Spinning Polymer Slip Mechanism and PEO/PVA Composite Fiber Preparation

Composite nanofibers with excellent physical and chemical properties are widely used in new energy, biomedical, environmental, electronic, and other fields. Their preparation methods have been investigated extensively by many experts. High-speed centrifugal spinning is a novel method used to fabricate composite nanofibers. The slip mechanism of polymer solution flows is an important factor affecting the morphology and quality of composite nanofibers prepared by high-speed centrifugal spinning. As the polymer solution flows, the liquid wall slip occurs inside the nozzle, followed by liquid-liquid interface slip and gas-liquid interface slip. The factors affecting polymer slip were investigated by developing a mathematical model in the nozzle. This suggests that the magnitude of the velocity is an important factor that affects polymer slip and determines fiber quality and morphology. Under the same rotational speed, the smaller the nozzle diameter, the greater the concentration of velocity distribution and the smaller the diameter of the produced composite nanofibers. Finally, PEO/PVA composite nanofibers were prepared using high-speed centrifugal spinning equipment at 900-5000 rpm and nozzle diameters of 0.2 mm, 0.4 mm, 0.6 mm, and 0.8 mm. The morphology and quality of the collected PEO/PVA composite nanofibers were analyzed using scanning electron microscopy (SEM) and TG experiments. Then, the optimal parameters for the preparation of PEO/PVA composite nanofibers by high-speed centrifugal spinning were obtained by combining the external environmental factors in the preparation process. Theoretical evaluation and experimental data were provided for the centrifugal composite spinning slip mechanism and for the preparation of composite nanofibers.

Controlled Release of a Therapeutic Peptide in Sprayable Surgical Sealant for Prevention of Postoperative Abdominal Adhesions

Formation of asymmetric, rigid scar tissue known as surgical adhesions is caused by traumatic disruption of mesothelial-lined surfaces in surgery. A widely adopted prophylactic barrier material (Seprafilm) for the treatment of intra-abdominal adhesions is applied operatively as a pre-dried hydrogel sheet but has reduced translational efficacy due its brittle mechanical properties. Topically administered peritoneal dialysate (Icodextrin) and anti-inflammatory drugs have failed to prevent adhesions due to an uncontrolled release profile. Hence, inclusion of a targeted therapeutic into a solid barrier host matrix with improved mechanical properties could provide dual utility in adhesion prevention and as a surgical sealant. Spray deposition of poly(lactide-co-caprolactone) (PLCL) polymer fibers through solution blow spinning has yielded a tissue-adherent barrier material with previously reported adhesion prevention efficacy due to a surface erosion mechanism that inhibits deposition of inflamed tissue. However, such an approach uniquely presents an avenue for controlled therapeutic release through mechanisms of diffusion and degradation. Such a rate is kinetically tuned via facile blending of "high" molecular weight (HMW) and "low" molecular weight (LMW) PLCL with slow and fast biodegradation rates, respectively. Here, we explore viscoelastic blends of HMW PLCL (70% w/v) and LMW PLCL (30% w/v) as a host matrix for anti-inflammatory drug delivery. In this work, COG133, an apolipoprotein E (ApoE) mimetic peptide with potent anti-inflammatory properties was selected and tested. In vitro studies with PLCL blends presented low (∼30%) and high (∼80%) percent release profiles over a 14-day period based on the nominal molecular weight of the HMW PLCL component. Two independent mouse models of cecal ligation and cecal anastomosis significantly reduced adhesion severity versus Seprafilm, COG133 liquid suspension, and no treatment control. The synergy of physical and chemical methods in a barrier material with proven preclinical studies highlights the value of COG133-loaded PLCL fiber mats in effectively dampening the formation of severe abdominal adhesions.

Obtaining poly (lactic acid) nanofibers encapsulated with peppermint essential oil as potential packaging via solution-blow-spinning

The development of active packaging based on biodegradable material and incorporating active compounds, such as essential oil, is a new technique to ensure food safety without harming the environment. In this study, nanofiber mats of poly (lactic acid)/ polyethylene glycol (PLA/PEG) blend incorporated with peppermint essential oil (PO) at different ratios (5-20 % v/w) were produced by solution-blow-spinning (SBS) for potential packaging application. Electron microscopy showed a cylindrical and interlaced morphology for PLA/PEG/PO and a significant increase in the diameter (139-192 nm) of the nanofibers by increasing PO content. All nanofibers showed high thermal stability (278-345 °C) suitable for use in the food industry. Nuclear magnetic resonance (¹³C NMR) spectrum confirmed PO in the nanofibers after SBS. ATR-FTIR spectral analysis supported the chemical composition of the nanofiber mats. PO addition led to obtaining hydrophobic nanofibers, enhancing the contact angle to 122° and decreasing water vapor permeability (60 % reduction compared to the PLA/PEG (3.0 g.mm.kPa^-1.h^-1.m^-2). Although the PLA/PEG/20%PO nanofibers did not show halo formation in 24 h, they effectively extended the strawberries' shelf-life at 25 °C, evidencing PO release over time. It also reduced weight loss (2.5 % and 0.3 % weight loss after 5 days for PLA/PEG and PLA/PEG/20%PO, respectively) and increased firmness (8-12 N) for strawberries packed with the nanofiber mats. It is suggested that PLA/PEG films incorporating PO may be used as an active, environmentally friendly packaging material.

Nanofiber-based sorbents: Current status and applications in extraction methods

Advanced sorbents gradually become a research hotspot on account of the increasing attention paid to environmental problems. Due to the prominent physicochemical features of nanofibers (NFs), such as high porosity, large surface area, favorable interconnectivity, high adsorption capacity, wettability, and the possibility of surface modification using functional groups, these nanostructures are regarded as excellent candidates for extraction applications. Therefore, the research in the field of NFs and their nanocomposites has been increasing in recent years. In the present review, we summarize the most recent studies on NFs-based sorbents focusing on strategies for preparation, characterization, and their unique capabilities as porous sorbents in various sorbent-based extraction methods. Moreover, we further described the performance and selectivity of sorbents to achieve improved extraction efficiency. Finally, some perspectives on the challenges and outlook are provided to aid future investigations related to this topic.

Spray nebulization enables polycaprolactone nanofiber production in a manner suitable for generation of scaffolds or direct deposition of nanofibers onto cells

Spray nebulization is an elegant, but relatively unstudied, technique for scaffold production. Herein we fabricated mesh scaffolds of polycaprolactone (PCL) nanofibers via spray nebulization of 8% PCL in dichloromethane (DCM) using a 55.2 kPa compressed air stream and 17 ml h-1polymer solution flow rate. Using a refined protocol, we tested the hypothesis that spray nebulization would simultaneously generate nanofibers and eliminate solvent, yielding a benign environment at the point of fiber deposition that enabled the direct deposition of nanofibers onto cell monolayers. Nanofibers were collected onto a rotating plate 20 cm from the spray nozzle, but could be collected onto any static or moving surface. Scaffolds exhibited a mean nanofiber diameter of 910 ± 190 nm, ultimate tensile strength of 2.1 ± 0.3 MPa, elastic modulus of 3.3 ± 0.4 MPa, and failure strain of 62 ± 6%.In vitro, scaffolds supported growth of human keratinocyte cell epithelial-like layers, consistent with potential utility as a dermal scaffold. Fourier-transform infrared spectroscopy demonstrated that DCM had vaporized and was undetectable in scaffolds immediately following production. Exploiting the rapid elimination of DCM during fiber production, we demonstrated that nanofibers could be directly deposited on to cell monolayers, without compromising cell viability. This is the first description of spray nebulization generating nanofibers using PCL in DCM. Using this method, it is possible to rapidly produce nanofiber scaffolds, without need for high temperatures or voltages, yielding a method that could potentially be used to deposit nanofibers onto cell cultures or wound sites.

Advanced functional nanofibers: strategies to improve performance and expand functions

Nanofibers have a wide range of applications in many fields such as energy generation and storage, environmental sensing and treatment, biomedical and health, thanks to their large specific surface area, excellent flexibility, and superior mechanical properties. With the expansion of application fields and the upgrade of application requirements, there is an inevitable trend of improving the performance and functions of nanofibers. Over the past few decades, numerous studies have demonstrated how nanofibers can be adapted to more complex needs through modifications of their structures, materials, and assembly. Thus, it is necessary to systematically review the field of nanofibers in which new ideas and technologies are emerging. Here we summarize the recent advanced strategies to improve the performances and expand the functions of nanofibers. We first introduce the common methods of preparing nanofibers, then summarize the advances in the field of nanofibers, especially up-to-date strategies for further enhancing their functionalities. We classify these strategies into three categories: design of nanofiber structures, tuning of nanofiber materials, and improvement of nanofibers assemblies. Finally, the optimization methods, materials, application areas, and fabrication methods are summarized, and existing challenges and future research directions are discussed. We hope this review can provide useful guidance for subsequent related work.

Graphical abstract

Latest on biomaterial-based therapies for topical treatment of psoriasis

Psoriasis is an autoimmune inflammatory disease which is fundamentally different from dermatitis. Its treatments include topical medications and systemic drugs depending on different stages of the disease. However, these commonly used therapies are falling far short of clinical needs due to various drawbacks. More precise therapeutic strategies with minimized side effects and improved compliance are highly demanded. Recently, the rapid development of biomaterial-based therapies has made it possible and promising to attain topical psoriasis treatment. In this review, we briefly describe the significance and challenges of the topical treatment of psoriasis and emphatically overview the latest progress in novel biomaterial-based topical therapies for psoriasis including microneedles, nanoparticles, nanofibers, and hydrogels. Current clinical trials related to each biomaterial are also summarized and discussed.

An overview on electrospinning and its advancement toward hard and soft tissue engineering applications

One of the emerging technologies of the recent times harboring nanotechnology to fabricate nanofibers for various biomedical and environmental applications are electrospinning (nanofiber technology). Their relative ease in use, simplicity, functionality and diversity has surpassed the pitfalls encountered with the conventional method of generating fibers. This review aims to provide an overview of electrospinning, principle, methods, feed materials, and applications toward tissue engineering. To begin with, evolution of electrospinning and its typical apparatus have been briefed. Simultaneously, discussion on the production of nanofibers with diversified feed materials such as polymers, small molecules, colloids, and nanoparticles and its transformation into a powerful technology has been dealt with. Further, highlights on the application of nanofibers in tissue engineering and the commercialized products developed using nanofiber technology have been summed up. With this rapidly emerging technology, there would be a great demand pertaining to scalability and environmental challenge toward tissue engineering applications.

Nanofibrous materials affect the reaction of cytotoxicity assays

Nanofibrous materials are widely investigated as a replacement for the extracellular matrix, the 3D foundation for cells in all tissues. However, as with every medical material, nanofibers too must pass all safety evaluations like in vitro cytotoxicity assays or in vivo animal tests. Our literature research showed that differences in results of widely used cytotoxicity assays applied to evaluate nanofibrous materials are poorly understood. To better explore this issue, we prepared three nanofibrous materials with similar physical properties made of poly-L-lactic acid, polyurethane, and polycaprolactone. We tested five metabolic cytotoxicity assays (MTT, XTT, CCK-8, alamarBlue, PrestoBlue) and obtained different viability results for the same nanofibrous materials. Further, the study revealed that nanofibrous materials affect the reaction of cytotoxicity assays. Considering the results of both described experiments, it is evident that validating all available cytotoxicity assays for nanofibrous materials and possibly other highly porous materials should be carefully planned and verified using an additional analytical tool, like scanning electron microscopy or, more preferably, confocal microscopy.

Sprayable tissue adhesive with biodegradation tuned for prevention of postoperative abdominal adhesions

Adhesions are dense, fibrous bridges that adjoin tissue surfaces due to uncontrolled inflammation following postoperative mesothelial injury. A widely used adhesion barrier material in Seprafilm often fails to prevent transverse scar tissue deposition because of its poor mechanical properties, rapid degradation profile, and difficulty in precise application. Solution blow spinning (SBS), a polymer fiber deposition technique, allows for the placement of in situ tissue-conforming and tissue-adherent scaffolds with exceptional mechanical properties. While biodegradable polymers such as poly(lactic-co-glycolic acid) (PLGA) have desirable strength, they exhibit bulk biodegradation rates and inflammatory profiles that limit their use as adhesion barriers and result in poor tissue adhesion. Here, viscoelastic poly(lactide-co-caprolactone) (PLCL) is used for its pertinent biodegradation mechanism. Because it degrades via surface erosion, spray deposited PLCL fibers can dissolve new connections formed by inflamed tissue, allowing them to function as an effective, durable, and easy-to-apply adhesion barrier. Degradation kinetics are tuned to match adhesion formation through the design of PLCL blends comprised of highly adhesive "low"-molecular weight (LMW) constituents in a mechanically robust "high"-molecular weight (HMW) matrix. In vitro studies demonstrate that blending LMW PLCL (30% w/v) with HMW PLCL (70% w/v) yields an anti-fibrotic yet tissue-adhesive polymer sealant with a 14-day erosion rate countering adhesion formation. PLCL blends additionally exhibit improved wet tissue adhesion strength (~10 kPa) over a 14-day period versus previously explored biodegradable polymer compositions, such as PLGA. In a mouse cecal ligation model, select PLCL blends significantly reduce abdominal adhesions severity versus no treatment and Seprafilm-treated controls.

Pneumatospinning Biomimetic Scaffolds for Meniscus Tissue Engineering

Nanofibrous scaffolds fabricated via electrospinning have been proposed for meniscus tissue regeneration. However, the electrospinning process is slow, and can only generate scaffolds of limited thickness with densely packed fibers, which limits cell distribution within the scaffold. In this study, we explored whether pneumatospinning could produce thicker collagen type I fibrous scaffolds with higher porosity, that can support cell infiltration and neo-fibrocartilage tissue formation for meniscus tissue engineering. We pneumatospun scaffolds with solutions of collagen type I with thicknesses of approximately 1 mm in 2 h. Scanning electron microscopy revealed a mix of fiber sizes with diameters ranging from 1 to 30 µm. The collagen scaffold porosity was approximately 48% with pores ranging from 7.4 to 100.7 µm. The elastic modulus of glutaraldehyde crosslinked collagen scaffolds was approximately 45 MPa, when dry, which reduced after hydration to 0.1 MPa. Mesenchymal stem cells obtained from the infrapatellar fat pad were seeded in the scaffold with high viability (&gt;70%). Scaffolds seeded with adipose-derived stem cells and cultured for 3 weeks exhibited a fibrocartilage meniscus-like phenotype (expressing COL1A1, COL2A1 and COMP). Ex vivo implantation in healthy bovine and arthritic human meniscal explants resulted in the development of fibrocartilage-like neotissues that integrated with the host tissue with deposition of glycosaminoglycans and collagens type I and II. Our proof-of-concept study indicates that pneumatospinning is a promising approach to produce thicker biomimetic scaffolds more efficiently that electrospinning, and with a porosity that supports cell growth and neo-tissue formation using a clinically relevant cell source.

Blow-Spun Collagen Nanofibrous Spongy Membrane: Preparation and Characterization

Fibrous biotextiles are very popular structural forms that are widely used in medical products and devices ranging from sutures, bandages, wound dressing, and patches to all kinds of artificial grafts such as ligaments, tendons, blood vessels, heart valves, and tissue engineered scaffolds. Blow-spinning is a recently developed technique that enables the large-scale and efficient production of ultrathin fibers with diameters ranging from micrometer to nanometer. In this study, the blow-spinning process and parameters were optimized to steadily fabricate collagen nanofibers by ejecting a collagen solution with constant airflow with precisely controlled diameter and alignment. Different from the electrospun collagen nanofibrous membrane, the blow-spun one was fluffy and spongy with high porosity. It was observed that the blow-spun collagen membrane could better maintain the fiber structure after chemical crosslinking in comparison with the electrospun membrane crosslinked in the same condition, which probably attributed to the good porosity and permeability of crosslinking agent within the membranes. The in vitro cell culture of Schwann cells on the blow-spun collagen nanofibrous spongy membrane showed its good biocompatibility for cell attachment, growth, and migration into the membrane, implying its potential in biomedical applications. Besides, there is no requirement for electroconductivity of the polymer solution and collector in blow-spinning. In brief, our results indicated that blow-spinning is an accessible and efficient technique to prepare nanofibers of synthetic and natural polymers, which has a great prospect in the large-scale production of biotextile medical devices and tissue engineered scaffolds. Impact statement Solution blow-spinning is a recently developed fiber fabrication technology with efficient and large-scale production. In this study, we successfully prepared collagen nanofibrous membrane with precisely controlled diameter and alignment by blow-spinning. The blow-spun collagen nanofibrous spongy membrane could better maintain the fiber structure after chemical crosslinking, which showed good biocompatibility for cell spreading and migration inward.

Biocompatibility of electrospun cell culture scaffolds made from balangu seed mucilage/PVA composites

Synthesis of Balangu (Lallemantia royleana) seed mucilage (BSM) solutions combined with polyvinyl alcohol (PVA) was studied for the purpose of producing 3D electrospun cell culture scaffolds. Production of pure BSM nanofibers proved to be difficult, yet integration of PVA contributed to a facile and successful formation of BSM/PVA nanofibers. Different BSM/PVA ratios were fabricated to achieve the desired nanofibrous structure for cell proliferation. It is found that the optimal bead-free ratio of 50/50 with a mean fiber diameter of ≈180 nm presents the most desirable scaffold structure for cell growth. The positive effect of PVA incorporation was approved by analyzing BSM/PVA solutions through physiochemical assays such as electrical conductivity, viscosity and surface tension tests. According to the thermal analysis (TGA/DSC), incorporation of PVA enhanced thermal stability of the samples. Successful fabrication of the nanofibers is verified by FT-IR spectra, where no major chemical interaction between BSM and PVA is detected. The crystallinity of the electrospun nanofibers is investigated by XRD, revealing the nearly amorphous structure of BSM/PVA scaffolds. The MTT assay is employed to verify the biocompatibility of the scaffolds. The cell culture experiment using epithelial Vero cells shows the affinity of the cells to adhere to their nanofibrous substrate and grow to form continuous cell layers after 72 h of incubation.

Incorporating redox-sensitive nanogels into bioabsorbable nanofibrous membrane to acquire ROS-balance capacity for skin regeneration

Facing the high incidence of skin diseases, it is urgent to develop functional materials with high bioactivity for wound healing, where reactive oxygen species (ROS) play an important role in the wound healing process mainly via adjustment of immune response and neovasculation. In this study, we developed a kind of bioabsorbable materials with ROS-mediation capacity for skin disease therapy. Firstly, redox-sensitive poly(N-isopropylacrylamide-acrylic acid) (PNA) nanogels were synthesized by radical emulsion polymerization method using a disulfide molecule as crosslinker. The resulting nanogels were then incorporated into the nanofibrous membrane of poly(l-lactic acid) (PLLA) via airbrushing approach to offer bioabsorbable membrane with redox-sensitive ROS-balance capacity. In vitro biological evaluation indicated that the PNA-contained bioabsorbable membrane improved cell adhesion and proliferation compared to the native PLLA membrane. In vivo study using mouse wound skin model demonstrated that PNA-doped nanofibrous membranes could promote the wound healing process, where the disulfide bonds in them were able to adjust the ROS level in the wound skin for mediation of redox potential to achieve higher wound healing efficacy.

Biodegradable, Tissue Adhesive Polyester Blends for Safe, Complete Wound Healing

Pressure-sensitive adhesives typically used for bandages are nonbiodegradable, inhibiting healing, and may cause an allergic reaction. Here, we investigated the effect of biodegradable copolymers with promising thermomechanical properties on wound healing for their eventual use as biodegradable, biocompatible adhesives. Blends of low molecular weight (LMW) and high molecular weight (HMW) poly(lactide-co-caprolactone) (PLCL) are investigated as tissue adhesives in comparison to a clinical control. Wounds treated with PLCL blend adhesives heal completely with similar vascularization, scarring, and inflammation indicators, yet require fewer dressing changes due to integration of the PLCL adhesive into the wound. A blend of LMW and HMW PLCL produces an adhesive material with significantly higher adhesive strength than either neat polymer. Wound adhesion is comparable to a polyurethane bandage, utilizing conventional nonbiodegradable adhesives designed for extremely strong adhesion.

Improved hemostatic effects by Fe3+ modified biomimetic PLLA cotton-like mat via sodium alginate grafted with dopamine

The development of an excellent, bioabsorbable hemostatic material for deep wound remains a challenge. In this work, a biodegradable cotton-like biomimetic fibrous mat of poly (l-lactic acid) (PLLA) was made by melt spinning. Subsequently, SD composite was prepared by cross-linking sodium alginate (SA) with dopamine (DA). It was immobilized on the fibre surface, which inspired by mussel byssus. Finally, Fe3+ was loaded onto the 0.5SD/PLLA composite by chelation with the carboxyl of alginate and phenolic hydroxy of dopamine. The haemostasis experiment found that the hemostatic time 47 s in vitro. However, the bleeding volume was 0.097 g and hemostatic time was 23 s when 20Fe3+-0.5SD/PLLA was applied in the haemostasis of the rat liver. As a result of its robust hydrophilicity and bouffant cotton-like structure, it could absorb a large water from blood, which could concentrate the component of blood and reduce the clotting time. Furthermore, the addition of Fe3+ in the 0.5SD/PLLA had a significant effect on improve hemostatic property. It also displayed excellent antibacterial property for Escherichia coli and Staphylococcus aureus. Notably, it possesses superior hemocompatibility, cytocompatibility and histocompatibility. Hence, 20Fe3+-0.5SD/PLLA has high potential application in haemostasis for clinical settings due to its outstanding properties.

Solution blow spinning of PLLA/hydroxyapatite composite scaffolds for bone tissue engineering

Composite poly-L-lactide acid-based scaffolds with hydroxyapatite (HAp) content up to 75 wt.% were fabricated via solution blow spinning. The influence of HAp concentration on structure, wettability, mechanical properties and chemical and phase composition of the produced materials was examined. It was found that with an increase of HAp content the average fiber diameter was increased, the uniaxial strength and relative elongation were reduced, while the phase composition and surface wettability did not change. The performance of the scaffolds during implantation in the parietal bone of a rat skull for a period from 15 to 90 days was studied. The materials have shown high ability to integrate with both soft and hard tissues. It was found that scaffolds with 25 wt.% HAp content significantly enhance osteogenesis during scarification (damage) of the periosteum. Overall, the fabricated scaffolds proved to be highly efficient for replacing bone defects in long tubular bones.

Study of Air Pressure and Velocity for Solution Blow Spinning of Polyvinylidene Fluoride Nanofibres

Solution blow spinning (SBS) is gaining popularity for producing fibres for smart textiles and energy harvesting due to its operational simplicity and high throughput. The whole SBS process is significantly dependent on the characteristics of the attenuation force, i.e., compressed air. Although variation in the fibre morphology with varying air input pressure has been widely investigated, there is no available literature on the experimentally determined flow characteristics. Here, we have experimentally measured and calculated airflow parameters, namely, output air pressure and velocity in the nozzle wake at 12 different pressure values between 1 and 6 bar and 11 different positions (retracted 5 mm to 30 mm) along the centreline. The results obtained in this work will answer many critical questions about optimum protrusion length for the polymer solution syringe and approximate mean fibre diameter for polyvinylidene fluoride (PVDF) at given output air pressure and velocity. The highest output air pressure and velocity were achieved at a distance of 3–5 mm away from the nozzle wake and should be an ideal location for the apex of the polymer solution syringe. We achieved 250 nm PVDF fibres when output air pressure and velocity were 123 kPa and 387 m/s, respectively.

Polydopamine Nanocluster Embedded Nanofibrous Membrane via Blow Spinning for Separation of Oil/Water Emulsions

Developing a porous separation membrane that can efficiently separate oil-water emulsions still represents a challenge. In this study, nanofiber membranes with polydopamine clusters polymerized and embedded on the surface were successfully constructed using a solution blow-spinning process. The hierarchical surface structure enhanced the selective wettability, superhydrophilicity in air (≈0°), and underwater oleophobicity (≈160.2°) of the membrane. This membrane can effectively separate oil-water emulsions, achieving an excellent permeation flux (1552 Lm-2 h-1) and high separation efficiency (~99.86%) while operating only under the force of gravity. When the external driving pressure was increased to 20 kPa, the separation efficiency hardly changed (99.81%). However, the permeation flux significantly increased to 5894 Lm-2 h-1. These results show that the as-prepared polydopamine nanocluster-embedded nanofiber membrane has an excellent potential for oily wastewater treatment applications.

Angiogenic potential of airbrushed fucoidan/polycaprolactone nanofibrous meshes

Implantation of biomaterials and hybrid constructs in tissue engineering approaches presents major limitations such as inflammatory reaction and the lack of vasculature integration. Therefore, new strategies are needed to enhance implant function, immune protection, and revascularization. In this work, we developed fibrous meshes composed of fucoidan (Fu), a sulfated polysaccharide extracted from brown algae, and polycaprolactone (PCL), a synthetic biodegradable polymer, using the airbrush technique. The chemical characterization by FTIR, EDS, and XPS confirmed the presence of the two polymers in the structure of airbrushed nanofibrous meshes (ANFM). Moreover, these nanofibrous exhibited good wettability and mechanical properties envisaging their application as templates for biomaterials and cell culture. The developed ANFM were directly cultured with human pulmonary microvascular endothelial (HPMEC-ST1.6R) cells for up to 7 days. Biological results demonstrated that ANFM comprising Fu promoted cellular attachment, spreading, and proliferation of human endothelial cells. The angiogenic potential of ANFM was further evaluated by onplantation of PCL and PCL/Fu ANFM in chick chorioallantoic membrane (CAM). In ovo and ex ovo results showed that the incorporation of Fu increased the pro-angiogenic potential of ANFM. Altogether, the results suggest that airbrush biocomposite meshes could be used as a biomaterial substrate to promote vascularization.

One-Step, Large-Scale Blow Spinning to Fabricate Ultralight, Fibrous Sorbents with Ultrahigh Oil Adsorption Capacity

The cleanup of spilled oil from water has always been a severe and urgent issue, which attracted great attention and interest. In this study, we reported a highly efficient large-scale blow spinning technique to fabricate fibrous oil sorbents including the polystyrene (PS) fibrous sponge and polyvinylidene fluoride (PVDF)/polystyrene (PS) composite package with ultrahigh oil adsorption capacity. The wide diameter distributions and multilevel pore structure of PS fibers were obtained by controlling the precursor solution compositions used in blow spinning. The PS fibrous sponge formed by accumulating naturally exhibited an ultralow density, whose oil adsorption capacity ranged from 74 to 440 g/g for various oils and organic solvents. To enhance the mechanical strength of the PS fibrous sponge, the PVDF/PS composite package with the sandwich structure was fabricated by alternately blow spinning. The PVDF/PS composite package possessed 2.7 times the tensile strength of the PS fibrous sponge while the oil adsorption capacity had merely a slight decrease. Moreover, the fabrication strategy of blow spinning used to produce the fibrous sponge and composite package is highly efficient, cost-effective, and environment-friendly, which is suitable for large-scale industrial production of oil sorbents and oil spill cleanup in environment protection.

Recent progress and challenges in solution blow spinning

In the past 30 years, researchers have worked towards reducing the size of ordinary three-dimensional (3D) materials into 1D or 2D materials in order to obtain new properties and applications of these low-dimensional systems. Among them, functional nanofibers with large surface area and high porosity have been widely studied and paid attention to. Because of the interesting properties of nanofibers, they find extensive application in filtration, wound dressings, composites, sensors, capacitors, nanogenerators, etc. Recently, a variety of nanofiber preparation methods such as melt blowing, electrospinning (e-spinning), centrifugal spinning and solution blow spinning (SBS) have been proposed. This paper includes a brief review of the fundamental principles of the preparation of nanofibers for solution jet spinning, the influence of experimental parameters, and the properties and potential applications of the solution-blown fibers. And the industrialization and challenges of SBS are also included.

Blowspinning: A New Choice for Nanofibers

Blowspinning is a new technique that enables the large-scale production of fibers with diameters ranging from micrometer to nanometer, which is more like a combination of melt-blown and electrospinning but has its own characteristics. This method can be used to deposit fibers in situ and produce various fibrous materials, such as coating, nonwoven, and sponge. These characteristics provide a new strategy for nanofiber application and attract the interest of many researchers. Regarding the blowspinning technique, systematic research had been carried out, involving basic principles, empirical studies, spinning equipment, and application. This review is intended to emphasize trends and gaps in the form of a concise illustration of various research directions.

Hemostatic nanotechnologies for external and internal hemorrhage management

An uncontrolled hemorrhage can easily lead to death during surgery and military operations. Despite the significant advances in hemostatic research, there is still an urgent and increasing need for safer and more effective hemostatic materials. Recently, nanotechnologies have been receiving increasing interest owing to their unique advantages and have been propelling the developement of hemostatic materials. This review summarizes the fundamentals of hemostasis and emphasizes the recent developments regarding hemorrhage-related hemostatic nanotechnologies. In terms of external accessible hemorrhage management, natural and synthetic polymers and inorganic components that have been used in traditional hemostats provide novel nanoscale solutions. Regarding internal noncompressible hemorrhage management, current research endeavors are dedicated to the development of substitutes for blood components, and nanoformulated hemostatic drugs. This review also briefly discusses the main and persistent problems of hemostatic nanomaterials, including safety concerns and clinical translation challenges. This review is hoped to provide critical insight into hemostatic nanomaterial development.

Electrospun Nimodipine-loaded fibers for nerve regeneration: Development and in vitro performance

Nimodipine is a 1,4-Dihydropyridine type calcium antagonist routinely used to control blood pressure and reduce the risk of secondary ischemia after aneurismal subarachnoid hemorrhage. Additionally, Nimodipine has unique neuroprotective properties. With respect to brain related applications, the full potential of the desired local effect can often not be realized after systemic administration due to systemic side effects. Therefore, it was our aim to develop a biodegradable drug delivery system for the local controlled release of the drug inside the brain. As a suitable and biodegradable system we successfully electrospun PLGA fibers containing 1 and 10% drug. The results of DSC and X-Ray diffractometry measurements indicate that Nimodipine was incorporated in the polymer matrix in the amorphous state. No drug recrystallization was detected for up to 6 months. Electron-beam sterilization was tried but reduced the drug content of the fiber mats considerably. A sustained drug release over 4-8 days was observed, highly depended on release conditions. The Nimodipine fiber mats exhibited no cell toxicity. In contrast, the electrospun fibers were able to significantly reduce cell death in in vitro cell models of oxidative, osmotic and heat-induced cell stress in Schwann cells, neuronal cells as well as immortalized and primary astrocytes. Therefore, electrospun Nimodipine loaded PLGA fibers represent a promising drug delivery system to realize the druǵs benefits for its intracranial use.

A step toward engineering thick tissues: Distributing microfibers within 3D printed frames

Microfiber mats for tissue engineering scaffolds support cell growth, but are limited by poor cell infiltration and nutrient transport. Three-dimensional printing, specifically fused deposition modeling (FDM), can rapidly produce customized constructs, but macroscopic porosity resulting from low resolution reduces cell seeding efficiency and prevents the formation of continuous cell networks. Here we describe the fabrication of hierarchical scaffolds that integrate a fibrous microenvironment with the open macropore structure of FDM. Biodegradable tyrosine-derived polycarbonate microfibers were airbrushed iteratively between layers of 3D printed support structure following optimization. Confocal imaging showed layers of airbrushed fiber mats supported human dermal fibroblast growth and extracellular matrix development throughout the scaffold. When implanted subcutaneously, hierarchical scaffolds facilitated greater cell infiltration and tissue formation than airbrushed fiber mats. Fibronectin matrix assembled in vitro throughout the hierarchical scaffold survived decellularization and provided a hybrid substrate for recellularization with mesenchymal stromal cells. These results demonstrate that by combining FDM and airbrushing techniques we can engineer customizable hierarchical scaffolds for thick tissues that support increased cell growth and infiltration.

Hydrogel Bioink Reinforcement for Additive Manufacturing: A Focused Review of Emerging Strategies

Bioprinting is an emerging approach for fabricating cell-laden 3D scaffolds via robotic deposition of cells and biomaterials into custom shapes and patterns to replicate complex tissue architectures. Bioprinting uses hydrogel solutions called bioinks as both cell carriers and structural components, requiring bioinks to be highly printable while providing a robust and cell-friendly microenvironment. Unfortunately, conventional hydrogel bioinks have not been able to meet these requirements and are mechanically weak due to their heterogeneously crosslinked networks and lack of energy dissipation mechanisms. Advanced bioink designs using various methods of dissipating mechanical energy are aimed at developing next-generation cellularized 3D scaffolds to mimic anatomical size, tissue architecture, and tissue-specific functions. These next-generation bioinks need to have high print fidelity and should provide a biocompatible microenvironment along with improved mechanical properties. To design these advanced bioink formulations, it is important to understand the structure-property-function relationships of hydrogel networks. By specifically leveraging biophysical and biochemical characteristics of hydrogel networks, high performance bioinks can be designed to control and direct cell functions. In this review article, current and emerging approaches in hydrogel design and bioink reinforcement techniques are critically evaluated. This bottom-up perspective provides a materials-centric approach to bioink design for 3D bioprinting.

Leucine-activated nanohybrid biofilm for skin regeneration via improving cell affinity and neovascularization capacity

Nanohybrids containing amino acid are doped into biodegradable nanofibrous membranes, which improves the cell affinity, the migration and growth of fibroblasts, and the neovascularization capacity, comprehensively accelerating a rapid wound healing.

Sprayable and biodegradable, intrinsically adhesive wound dressing with antimicrobial properties

Conventional wound dressings are difficult to apply to large total body surface area (TBSA) wounds, as they typically are prefabricated, require a layer of adhesive coating for fixation, and need frequent replacement for entrapped exudate. Large TBSA wounds as well as orthopedic trauma and low-resource surgery also have a high risk of infection. In this report, a sprayable and intrinsically adhesive wound dressing loaded with antimicrobial silver is investigated that provides personalized fabrication with minimal patient contact. The dressing is composed of adhesive and biodegradable poly(lactic-co-glycolic acid) and poly(ethylene glycol) (PLGA/PEG) blend fibers with or without silver salt (AgNO3). in vitro studies demonstrate that the PLGA/PEG/Ag dressing has antimicrobial properties and low cytotoxicity, with antimicrobial silver controllably released over 7-14 days. In a porcine partial-thickness wound model, the wounds treated with both antimicrobial and nonantimicrobial PLGA/PEG dressings heal at rates similar to those of the clinical, thin film polyurethane wound dressing, with similar scarring. However, PLGA/PEG adds a number of features beneficial for wound healing: greater exudate absorption, integration into the wound, a 25% reduction in dressing changes, and tissue regeneration with greater vascularization. There is also modest improvement in epidermis thickness compared to the control wound dressing.

Light scattering effect of polyvinyl-alcohol/titanium dioxide nanofibers in the dye-sensitized solar cell

In the present work, polyvinyl-alcohol/titanium dioxide (PVA/TiO2) nanofibers are utilized as a light scattering layer (LSL) on top of the TiO2 nanoparticles photoanode. The TiO2 nanoparticles decorated PVA/TiO2 nanofibers display a power conversion efficiency (PCE) of 4.06%, which is 33% higher than TiO2 nanoparticles without LSL, demonstrating the incorporation of PVA/TiO2 nanofibers as LSL reduces the radiation loss and increases the excitation of the electron that leads to high PCE. The incorporation of PVA/TiO2 nanofibers as LSL also increases the electron life time and charge collection efficiency in comparison to the TiO2 nanoparticles without LSL.

Improved mechanical performance of self-adhesive resin cement filled with hybrid nanofibers-embedded with niobium pentoxide

OBJECTIVES

In this study hybrid nanofibers embedded with niobium pentoxide (Nb₂O₅) were synthesized, incorporated in self-adhesive resin cement, and their influence on physical-properties was evaluated.

METHODS

Poly(D,L-lactide), PDLLA cotton-wool-like nanofibers with and without silica-based sol-gel precursors were formulated and spun into submicron fibers via solution blow spinning, a rapid fiber forming technology. The morphology, chemical composition and thermal properties of the spun fibers were characterized by field emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectroscopy (EDS) and Fourier-transform infrared spectroscopy (FTIR), and differential scanning calorimetry (DSC), respectively. Produced fibers were combined with a self-adhesive resin cement (RelyX U200, 3M ESPE) in four formulations: (1) U200 resin cement (control); (2) U200+1wt.% PDLLA fibers; (3) U200+1wt.% Nb₂O₅-filled PDLLA composite fibers and (4) U200+1wt.% Nb₂O₅/SiO₂-filled PDLLA inorganic-organic hybrid fibers. Physical properties were assessed in flexure by 3-point bending (n=10), Knoop microhardness (n=5) and degree of conversion (n=3). Data were analyzed with One-way ANOVA and Tukey's HSD (α=5%).

RESULTS

Composite fibers formed of PDLLA-Nb₂O₅ exhibited an average diameter of ∼250nm, and hybrid PDLLA+Nb₂O₅/SiO₂ fibers were slightly larger, ∼300nm in diameter. There were significant differences among formulations for hardness and flexural strength (p<0.05). Degree of conversion of resin cement was not affected for all groups, except for Group 4 (p<0.05).

SIGNIFICANCE

Hybrid reinforcement nanofibers are promising as fillers for dental materials. The self-adhesive resin cement with PDLLA+Nb₂O₅ and PDLLA+Nb₂O₅/SiO₂ presented superior mechanical performance than the control group.

Preparation of Nanofibrous PVDF Membrane by Solution Blow Spinning for Mechanical Energy Harvesting

Self-powered nanogenerators composed of poly(vinylidene fluoride) (PVDF) have received much attention. Solution blow spinning (SBS) is a neoteric process for preparing nanofiber mats with high efficiency and safely, and SBS is a mature fiber-forming technology that offers many advantages over conventional electrospinning methods. Herein, we adopted the SBS method to prepare independent PVDF nanofiber membranes (NFMs), and successfully employed them as nanogenerators. Finally, we tested the change in the output current caused by mechanical compression and stretching, and studied its durability and robustness by charging the capacitor, which can drive tiny electronic devices. The results show that the PVDF nanogenerators by using this SBS equipment can not only be used in wearable electronic textiles, but are also suitable for potential applications in micro-energy harvesting equipment.

Coaxial Electrospinning Formation of Complex Polymer Fibers and their Applications

The formation of fibers by electrospinning has experienced explosive growth in the past decade, recently reaching 4,000 publications and 1,500 patents per year. This impressive growth of interest is due to the ability to form fibers with a variety of materials, which lend themselves to a large and rapidly expanding set of applications. In particular, coaxial electrospinning, which forms fibers with multiple core-sheath layers from different materials in a single step, enables the combination of properties in a single fiber that are not found in nature in a single material. This article is a detailed review of coaxial electrospinning: basic mechanisms, early history and current status, and an in-depth discussion of various applications (biomedical, environmental, sensors, energy, catalysis, textiles). We aim to provide readers who are currently involved in certain aspects of coaxial electrospinning research an appreciation of other applications and of current results.

Effects of cylindrical-electrode-assisted solution blowing spinning process parameters on polymer nanofiber morphology and microstructure

Cylindrical-electrode-assisted solution blowing spinning (CSBS) is a novel method for preparing polymer nanofibers by using air-stretch and electrostatic simultaneously, which can fabricate thinner and more uniform nanofibers than the traditional solution blowing spinning (SBS). In this work, the effects of processing parameters including length of cylinder (LC), needle to cylinder distance (NCD) and left face of cylinder to collector distance (CCD) on the CSBS nanofiber diameter were investigated. The results are as follows: when the NCD decreased, the fiber diameter decreased; when the LC increased, the fiber diameter decreased; the CCD didn’t significantly affect the fiber diameter. Moreover, an orthogonal experimental design was utilized to investigate the effect of injection rate, air pressure, NCD, LC, diameter of cylinder (DC), voltage and CCD on the fiber diameter and porosity of various surface layers of nanofiber web (P1, P2, and P3). The results showed that the varied range of each properties (average diameter, standard deviation of the diameter, P1, P2, and P3) was 539.121-904.149 nm, 127.903-303.253, 71.464-85.1415%, 60.32725-75.46625%, 48.23925-70.08875%, respectively. We also found the order of the influence of the above-mentioned seven process parameters on each above properties of the nanofiber web, and the corresponding optimal spinning process parameters were listed. It is well known that the fiber diameter affects the mechanical properties of nanofibers, and porosity of nano-fiber webs is an important parameter in tissue engineering, bioengineering, and filtration. The effects of CSBS process parameters on nanofiber morphology and microstructure were investigated for the first time. The conclusion of the paper can help researchers to produce high quality CSBS nanofiber and promote the wider application of this novel technology.

Fabrication and Characterisation of Stimuli Responsive Piezoelectric PVDF and Hydroxyapatite-Filled PVDF Fibrous Membranes

Poly(vinylidene fluoride) has attracted interest from the biomaterials community owing to its stimuli responsive piezoelectric property and promising results for application in the field of tissue engineering. Here, solution blow spinning and electrospinning were employed to fabricate PVDF fibres and the variation in resultant fibre properties assessed. The proportion of piezoelectric β-phase in the solution blow spun fibres was higher than electrospun fibres. Fibre production rate was circa three times higher for solution blow spinning compared to electrospinning for the conditions explored. However, the solution blow spinning method resulted in higher fibre variability between fabricated batches. Fibrous membranes are capable of generating different cellular response depending on fibre diameter. For this reason, electrospun fibres with micron and sub-micron diameters were fabricated, along with successful inclusion of hydroxyapatite particles to fabricate stimuli responsive bioactive fibres.

Improving the adhesion, flexibility, and hemostatic efficacy of a sprayable polymer blend surgical sealant by incorporating silica particles

Commercially available surgical sealants for internal use either lack sufficient adhesion or produce cytotoxicity. This work describes a surgical sealant based on a polymer blend of poly(lactic-co-glycolic acid) (PLGA) and poly(ethylene glycol) (PEG) that increases wet tissue adherence by incorporation of nano-to-microscale silica particles, without significantly affecting cell viability, biodegradation rate, or local inflammation. In functional studies, PLGA/PEG/silica composite sealants produce intestinal burst pressures that are comparable to cyanoacrylate glue (160 mmHg), ∼2 times greater than the non-composite sealant (59 mmHg), and ∼3 times greater than fibrin glue (49 mmHg). The addition of silica to PLGA/PEG is compatible with a sprayable in situ deposition method called solution blow spinning and decreases coagulation time in vitro and in vivo. These improvements are biocompatible and cause minimal additional inflammation, demonstrating the potential of a simple composite design to increase adhesion to wet tissue through physical, noncovalent mechanisms and enable use in procedures requiring simultaneous occlusion and hemostasis. STATEMENT OF SIGNIFICANCE: Incorporating silica particles increases the tissue adhesion of a polymer blend surgical sealant. The particles enable interfacial physical bonding with tissue and enhance the flexibility of the bulk of the sealant, without significantly affecting cytotoxicity, inflammation, or biodegradation. These studies also demonstrate how silica particles decrease blood coagulation time. This surgical sealant improves upon conventional devices because it can be easily deposited with accuracy directly onto the surgical site as a solid polymer fiber mat. The deposition method, solution blow spinning, allows for high loading in the composite fibers, which are sprayed from a polymer blend solution containing suspended silica particles. These findings could easily be translated to other implantable or wearable devices due to the versatility of silica particles.