Improving structural and functional properties of starch-catechin-based green nanofiber mats for active food packaging by electrospinning and crosslinking techniques

The hydrophilic and low mechanical properties limited the application of starch-based films. In this work, a hydrophobic starch-based nanofiber mat was first successfully prepared from aqueous solution at room temperature by using electrospinning and glutaraldehyde (GTA) vapor phase crosslinking techniques for active packaging applications. Catechin (CAT) was immobilized in the nanofibers by electrospinning, resulting in higher thermal stability (Tdmax = 315.23 °C), antioxidant (DPPH scavenging activity = 94.31 ± 2.70 %) and antimicrobial (inhibition zone diameter = 15.6 ± 0.3 mm) of the fibers, which further demonstrated hydrogen bonding and electrostatic interaction between CAT and fibers. Nanofibers after GTA vapor phase crosslinking exhibited enhanced hydrophobicity (water contact angle: 15.6 ± 1.5° → 93.5 ± 2.3°) and mechanical properties (tensile strength: 1.82 ± 0.06 MPa → 7.64 ± 0.24 MPa, elastic modulus: 19.35 ± 0.63 MPa → 45.34 ± 0.51 MPa). The results demonstrated that preparation of starch-based electrospun nanofiber mats in aqueous system at room temperature overcame the challenges of organic solvent pollution and thermosensitive material encapsulation, while GTA vapor phase crosslinking technique improved the hydrophobicity and mechanical properties of nanofiber mats, which facilitated the application of starch-based materials in the field of packaging.

Progress of polysaccharide-based tissue adhesives

Recently, polymer-based tissue adhesives (TAs) have gained the attention of scientists and industries as alternatives to sutures for sealing and closing wounds or incisions because of their ease of use, low cost, minimal tissue damage, and short application time. However, poor mechanical properties and weak adhesion strength limit the application of TAs, although numerous studies have attempted to develop new TAs with enhanced performance. Therefore, next-generation TAs with improved multifunctional properties are required. In this review, we address the requirements of polymeric TAs, adhesive characteristics, adhesion strength assessment methods, adhesion mechanisms, applications, advantages and disadvantages, and commercial products of polysaccharide (PS)-based TAs, including chitosan (CS), alginate (AL), dextran (DE), and hyaluronic acid (HA). Additionally, future perspectives are discussed.

Natural Polymers as a Carrier for the Effective Delivery of Antineoplastic Drugs

Cancer is a broad term for a set of disorders marked by the development of physically and functionally changed cells that proliferate uncontrollably, infect neighboring tissues, and result in malignant tumours, 'neoplasm'. Cancer remains a difficult disease to treat because of the significant adverse effects and poor pharmacokinetic profile of antineoplastic drugs, despite advancements in our understanding of the features and behavior of tumor cells in recent decades. In this series, the role of natural polymers is prominent as a component of a novel delivery system of anticancer drugs. These natural polymeric drug delivery systems (NPDDS) have many advantages over synthetic polymers like controlled delivery, biodegradability, inexpensive, low toxicity profile, and easily obtainable. These polymers further modify for the targeting of tumour cells. This review discusses and critically analyses the different natural polymers, such as chitosan, cellulose, starch, albumin, dextran, fucoidan, gelatin, etc., in terms of natural ingredient-based polymeric nanocarriers specifically for cancer therapy. It also describes benefits, drawbacks, and opinions and provides insights about the efficacy of NPDDS as well as its future perspectives and tabulated recent patents and cases under clinical trials exploited for cancer treatment.

Amphotericin B-loaded natural latex dressing for treating Candida albicans wound infections using Galleria mellonella model

Amphotericin B (AmB) is the gold standard for antifungal drugs. However, AmB systemic administration is restricted because of its side effects. Here, we report AmB loaded in natural rubber latex (NRL), a sustained delivery system with low toxicity, which stimulates angiogenesis, cell adhesion and accelerates wound healing. Physicochemical characterizations showed that AmB did not bind chemically to the polymeric matrix. Electronic and topographical images showed small crystalline aggregates from AmB crystals on the polymer surface. About 56.6% of AmB was released by the NRL in 120 h. However, 33.6% of this antifungal was delivered in the first 24 h due to the presence of AmB on the polymer surface. The biomaterial's excellent hemo- and cytocompatibility with erythrocytes and human dermal fibroblasts (HDF) confirmed its safety for dermal wound application. Antifungal assay against Candida albicans showed that AmB-NRL presented a dose-dependent behavior with an inhibition halo of 30.0 ± 1.0 mm. Galleria mellonella was employed as an in vivo model for C. albicans infection. Survival rates of 60% were observed following the injection of AmB (0.5 mg.mL-1) in G. mellonella larvae infected by C. albicans. Likewise, AmB-NRL (0.5 mg.mL-1) presented survival rates of 40%, inferring antifungal activity against fungus. Thus, NRL adequately acts as an AmB-sustained release matrix, which is an exciting approach, since this antifungal is toxic at high concentrations. Our findings suggest that AmB-NRL is an efficient, safe, and reasonably priced ($0.15) dressing for the treatment of cutaneous fungal infections.

Natural polymer-based bioadhesives as hemostatic platforms for wound healing

Medical adhesives are advanced but challenging alternatives to wound closure and repair, especially in mitigating uncontrolled hemorrhage. Ideal hemostatic adhesives need to meet good biocompatibility and biodegradability, adequate mechanical strength, and strong tissue adhesion functionality under wet and dynamic conditions. Considering these requirements, natural polymers such as polysaccharide, protein and DNA, attract great attention as candidates for making bioadhesives because of their distinctive physicochemical performances and biological properties. This review systematically summarizes the advances of bioadhesives based on natural polysaccharide, protein and DNA. Various physical and chemical cross-linking strategies have been introduced for adhesive synthesis and their hemostatic applications are introduced from the aspect of versatility. Furthermore, the possible challenges and future opportunities of bioadhesives are discussed, providing insights into the development of high-performance hemostatic materials.

Intelligent food tag: A starch-anthocyanin-based pH-sensitive electrospun nanofiber mat for real-time food freshness monitoring

A starch-based nanofiber mat was prepared for real-time monitoring of food freshness for the first time. UV-vis results showed that roselle anthocyanins (RS) conferred a wide pH sensing range on the nanofiber mat. The prepared nanofiber mats demonstrated good color visibility (total color difference value (ΔE) increased to 56.4 ± 0.7) and a reversible response (within 120 s). Scanning electron microscopy and Fourier transform infrared spectroscopy results suggested that the nanofibers had smooth surfaces without beaded fibers and that RS was well embedded into the nanofibers. The introduction of RS improved the thermal stability of the nanofibers. Color stability tests revealed that the nanofibers exhibited excellent color stability (maximum change ΔE = 1.57 ± 0.03) after 14 days of storage. Pork and shrimp freshness tests verified that the nanofibers could effectively reflect the dynamic freshness of pork and shrimp. Nontoxic, degradable and responsive characteristics make the pH-sensitive nanofiber mat a smart food label with great application potential.

Hydrolysis effects on the water uptake of starch-g-glycidyl methacrylate (GMASt)/dimethylacrylamide (DMAAm)-based hydrogels for potential agricultural purposes

This work assessed the effect of different hydrolysis periods on the properties of hydrogels based on 75 % w w-1 of N,N'-dimethyl acrylamide (DMAAm) and 25 % w w-1 of starch-g-(glycidyl methacrylate) (GMASt). FTIR results confirmed the conversion of ester groups into carboxylic acids and carboxylates, besides forming a keto-enol tautomer due to the peeling reaction of starch. For DMAAm, the hydrolysis mostly converted amide into carboxylate groups. The morphology, thermal stability, and the mechanical properties of the predominantly amorphous matrices (as confirmed by XRD results) did not drastically change even after 10 days of hydrolysis in alkali media. However, the thermogravimetric analysis results suggested that DMAAm partially protected GMASt from the hydrolysis. The swelling degree of the matrix increased from (10.1 ± 2.1) g g-1 to (61.9 ± 2.6) g g-1 after 1 day of hydrolysis, but no statistical differences (at 95 % of significance) were observed for the matrices hydrolyzed for longer periods, confirming that the maximum hydrolysis occurred within 24 h. The results confirmed that the hydrolysis increased the water uptake of the GMASt/DMAAm-based matrices, making appealing for uses as a water retentor for agricultural purposes.

Electrospinning of pullulan-based orodispersible films containing sildenafil

Feasibility of electrospinning in the manufacturing of sildenafil-containing orodispersible films (ODFs) intended to enhance oxygenation and to reduce pulmonary arterial pressure in pediatric patients was evaluated. Given the targeted subjects, the simplest and safest formulation was chosen, using water as the only solvent and pullulan, a natural polymer, as the sole fiber-forming agent. A systematic characterization in terms of shear and extensional viscosity as well as surface tension of solutions containing different amounts of pullulan and sildenafil was carried out. Accordingly, electrospinning parameters enabling the continuous production, at the highest possible rate, of defect-free fibers with uniform diameter in the nanometer range were assessed. Morphology, microstructure, drug content and relevant solid state as well as ability of the resulting non-woven films to interact with aqueous fluids were evaluated. To better define the role of the fibrous nanostructure on the performance of ODFs, analogous films were produced by spin- and blade-coating and tested. Interestingly, the disintegration process of electrospun products turned out to be the fastest (i.e. occurring within few s) and compliant with Ph. Eur. and USP limits, making relevant ODFs particularly promising for increasing sildenafil bioavailability, thus lowering its dosages.

Box-Behnken design to optimize the cross-linked sodium alginate/mucilage/Aloe vera film: Physical and mechanical studies

The crosslinked sodium alginate/mucilage/Aloe vera/glycerin was optimized by different ratios of each factor to be an absorption wound dressing base for infected wound healing. Mucilage was extracted from seeds of Ocimum americanum. The Box-Behnken design (BBD) in response surface methodology (RSM) was used to construct an optimal wound dressing base with the target ranges of mechanical and physical properties of each formulation. The independent variables selected were sodium alginate (X1: 0.25-0.75 g), mucilage (X2: 0.00-0.30 g), Aloe vera (X3: 0.00-0.30 g), and glycerin (X4: 0.00-1.00 g). The dependent variables were tensile strength (Y1: low value), elongation at break (Y2: high value), Young's modulus (Y3: high value), swelling ratio (Y4: high value), erosion (Y5: low value), and moisture uptake (Y6: high value). The results showed that the wound dressing base with the most desirable response consists of sodium alginate (59.90 % w/w), mucilage (23.96 % w/w), and glycerin (16.14 % w/w) without Aloe vera gel powder (0.00 % w/w).

Multifunctional bilayer membranes composed of poly(lactic acid), beta-chitin whiskers and silver nanoparticles for wound dressing applications

Nanomaterial-based wound dressings have been extensively studied for the treatment of both minor and life-threatening tissue injuries. These wound dressings must possess several crucial characteristics, such as tissue compatibility, non-toxicity, appropriate biodegradability to facilitate wound healing, effective antibacterial activity to prevent infection, and adequate physical and mechanical strength to withstand repetitive dynamic forces that could potentially disrupt the healing process. Nevertheless, the development of nanostructured wound dressings that incorporate various functional micro- and nanomaterials in distinct architectures, each serving specific purposes, presents significant challenges. In this study, we successfully developed a novel multifunctional wound dressing based on poly(lactic acid) (PLA) fibrous membranes produced by solution-blow spinning (SBS) and electrospinning. The PLA-based membranes underwent surface modifications aimed at tailoring their properties for utilization as effective wound dressing platforms. Initially, beta-chitin whiskers were deposited onto the membrane surface through filtration, imparting hydrophilic character. Afterward, silver nanoparticles (AgNPs) were incorporated onto the beta-chitin layer using a spray deposition method, resulting in platforms with antimicrobial properties against both Staphylococcus aureus and Escherichia coli. Cytotoxicity studies demonstrated the biocompatibility of the membranes with the neonatal human dermal fibroblast (HDFn) cell line. Moreover, bilayer membranes exhibited a high surface area and porosity (> 80%), remarkable stability in aqueous media, and favorable mechanical properties, making them promising candidates for application as multifunctional wound dressings.

Stretchable and recyclable gelatin Ionogel based ionic skin with extensive temperature tolerant, self-healing, UV-shielding, and sensing capabilities

Fabricating sustainable ionic skin with multi-functional outstanding performances using biocompatible natural polymer-based ionogel is highly desired but remains a great challenge up to now. Herein, a green and recyclable ionogel has been fabricated by in-situ cross-linking of gelatin with a green bio-based multifunctional cross-linker of Triglycidyl Naringenin in ionic liquid. Benefiting from the unique multifunctional chemical crosslinking networks along with multiple reversible non-covalent interactions, the as-prepared ionogels exhibit high stretchability (>1000 %), excellent elasticity, fast room-temperature self-healability (>98 % healing efficiency at 6 min), and good recyclability. These ionogels are also highly conductive (up to 30.7 mS/cm at 150 °C), and exhibit extensive temperature tolerance (-23 to 252 °C) and outstanding UV-shielding ability. As a result, the as-prepared ionogel can easily be applied as stretchable ionic skin for wearable sensors, which exhibits high sensitivity, fast response time (102 ms), excellent temperature tolerance, and stability over 5000 stretching-relaxing cycles. More importantly, the gelatin-based sensor can be used in signal monitor system for various human motion real-time detection. This sustainable and multifunctional ionogel provides a new idea for easy and green preparation of advanced ionic skins.

Progress of tissue adhesives based on proteins and synthetic polymers

In recent years, polymer-based tissue adhesives (TAs) have been developed as an alternative to sutures to close and seal incisions or wounds owing to their ease of use, rapid application time, low cost, and minimal tissue damage. Although significant research is being conducted to develop new TAs with improved performances using different strategies, the applications of TAs are limited by several factors, such as weak adhesion strength and poor mechanical properties. Therefore, the next-generation advanced TAs with biomimetic and multifunctional properties should be developed. Herein, we review the requirements, adhesive performances, characteristics, adhesive mechanisms, applications, commercial products, and advantages and disadvantages of proteins- and synthetic polymer-based TAs. Furthermore, future perspectives in the field of TA-based research have been discussed.

Exploring structure-activity relationships for polymer biodegradability by microorganisms

Research on the environmental biodegradation or microbial biodegradation of polymers has substantially increased recently due to growing demand for biodegradable polymers for certain applications. Environmental biodegradation of a polymer depends on the intrinsic biodegradability of the polymer and the characteristics of the receiving environment. The intrinsic biodegradability of a polymer is determined by the chemical structure and resulting physical properties (e.g., glass transition temperature, melting temperature, modulus of elasticity, crystallinity, and crystal structure) of the polymer. Quantitative structure-activity relationships (QSARs) on biodegradability have been well-established for discrete (non-polymeric) organic chemicals, but not for polymers due to the absence of adequate biodegradability data based on consistent and standardized biodegradation tests with appropriate characterization and reporting of the polymers tested. This review summarizes empirical structure-activity relationships (SARs) for biodegradability of polymers in laboratory studies involving various environmental matrices. In general, polyolefins with carbon-carbon chain are not biodegradable, while polymers containing labile bonds such as ester, ether, amide, or glycosidic bonds in their polymer chain may be favorable for biodegradation. Under a univariate scenario, polymers with higher molecular weight, higher crosslinking, lower water solubility, higher degree of substitution (i.e., higher average number of substituted functional groups per monomer unit), and higher crystallinity may result in reduced biodegradability. This review paper also highlights some of the challenges that hamper QSAR development for polymer biodegradability and stresses the need for better characterization of polymer structures used in biodegradation studies and emphasizes the necessity for consistent testing conditions for the ease of cross-comparison and quantitative modeling analysis during future QSAR development.

A bacteriostatic hemostatic dressing prepared from l-glutamine-modified chitosan, tannic acid-modified gelatin and oxidized dextran

In this study, porous hemostatic sponges (CGS1, CGS2 and CGS3) with proper absorption (38-43×) and air permeability (2214 g/m²·day) were prepared from l-glutamine-modified chitosan (CG), tannic acid-modified gelatin (GTA), and oxidized dextran (ODEX) by Schiff base crosslinking reaction. Among them, CGS2 was proved to have high porosity (88.98 %), durable water retention (>6 h), strong antibacterial activity, proper mechanical quality, and suitable tissue adhesion. In addition, CGS2 had good biocompatibility, mainly manifested in low hemolysis rate (<0.4 %), low cytotoxicity (relative cell activity>90 %), and good biodegradability in vitro. The hemostatic time and blood loss in CGS2 group were much lower than those in commercial gelatin sponge group in three animal injury models. Moreover, the activated partial thromboplastin time (APTT) and the prothrombin time (PT) results indicated that CGS2 promoted coagulation by activating the endogenous coagulation pathway. These results suggested that CGS2 had great potential for rapid hemostasis and avoidance of wound infection.

k-Carrageenan/sericin-based multiparticulate systems: A novel gastro-resistant polymer matrix for indomethacin delivery

This study aimed to develop a natural and multiparticulate carrier of k-carrageenan (k-Car) and sericin (Ser) for encapsulation of indomethacin (IND) in order to minimize gastrointestinal effects caused by immediate-release. Increasing the amount of IND in the formulations subtly reduced the entrapment efficiency (EE) and drug loading (DL) due to matrix saturation. Sericin was essential to improve EE and DL when compared to pure k-Car (EE > 90 % and DL > 47 %) with suitable particle sizes (1.3461 ± 0.1891-1.7213 ± 0.1586 mm). The incorporation and integrity of IND in the particles were confirmed by analytical techniques of HPLC, XRD, FTIR, and SEM. Additionally, the k-Car/Ser matrix was pH-responsive with low IND release at pH 1.2 and extended-release at pH 6.8. The Weibull model had an adequate fit to the experimental data with R²aju 0.950.99 and AIC 82.4-24.9, with curves in parabolic profile (b < 1) and indicative of a controlled drug-release mechanism by diffusion. Besides, k-Car/Ser/IND and placebo were not cytotoxic (cell viability > 85 % at 150-600 μM) for the Caco-2 cell line. Therefore, the polymeric matrix is gastro-resistant, stable, and biocompatible to carry indomethacin and deliver it to the intestinal environment.

High performance, cost-effective and ecofriendly flocculant synthesized by grafting carboxymethyl cellulose and alginate with itaconic acid

Natural polymer flocculant possesses an exciting prospect in water treatment due to its non-toxicity, wide source, low cost and biodegradability. In this work, we have successfully synthesized the anionic terpolymer of carboxymethyl cellulose-itaconic acid‑sodium alginate (CIS) by microwave-assisted copolymerization. By studying the flocculation properties towards cationic dye of crystal violet (CV), the optimum synthesis conditions were determined. The maximum removal rate of 100 mg/L CV simulated wastewater was 92.2 % with CIS concentration of 30 mg/L. The flocculation kinetic results showed the rapid dye removal rate and the dye decolorization ratio of 89.8 % could be obtained at 75 s. Moreover, the CIS flocculant showed excellent flocculation effects in ambient pH of 4-10, flocculation temperature of 10-40 °C, and various inorganic salts. In general, the anionic CIS flocculant shows excellent cost effectiveness, where the predicted operation cost of as-prepared CIS is about 60 % of conventional polyacrylamide flocculant. It also has the advantages of excellent ecofriendliness and rich raw material source, indicative its potential applications of wastewater treatment.

Lignin as a bioactive polymer and heavy metal absorber- an overview

As a pulping and bio-refinery by-product with phenolic chemical structure, lignin indicated high potential as natural antioxidant activity, UV blocker, antibacterial and toxic material absorbent properties. Presence of phenolic hydroxyl groups in lignin structure plays the main role of its antioxidant activity. However, lignin antioxidant power can change depending on its other structural features and functional groups like ortho-methoxy groups, -OCH₃ groups, the α-CH₂ groups, the aliphatic carbonyl groups, and the size of π-conjugated systems. Lignin in mixture with synthetic polymers, improved their thermal stability. Lignin has high UV light absorbing potential in broad-spectrum (UVA, UVB). Adding 1-5% of lignin into hand cream indicated excellent range of sun protection factor (SPF) with more than 95% UV light absorption. Lignin also indicated strong UV light protection when applied in different transparent film and protect paint, oil, and varnish from UV degradation. Lignosulfonate and other modified lignin including chemically modification, nano-particles and lignin hydrogel indicated high potential as heavy metal absorber.

Locust Bean Gum: Processing, Properties and Food Applications

Locust bean gum is derived from the seed endosperm of the Ceratonia siliqua carob tree and is known as locust bean or carob gum. Food, medicines, paper, textile, oil drilling, and cosmetic sectors all use it as an ingredient. Hydrogen bonding with water molecules makes locust bean gum useful in industrial settings. In addition, its dietary fibre activity helps regulate numerous health issues, including diabetes, bowel motions, heart disease and colon cancer. Locust bean gum production, processing, composition, characteristics, culinary applications, and health advantages are the subject of this article.

Fabrication of electrospun Mondia whitei/PVA nanofibres: application in the removal of acidic drugs

Novel electrospun Mondia whitei/PVA blend nanofibres were fabricated for potential water treatment applications by blending a natural polymer extracted from Mondia whitei (MW) roots with poly (vinyl alcohol) (PVA). The fabricated nanofibres were shown to have a smooth and uniform morphology with an average diameter of 99 ± 0.025 nm. The FTIR, XPS, XRD, and TGA characterisation results indicated changes in functional groups, crystallinity, and thermal stability of the Mondia whitei/PVA blend nanofibres, as compared to the original material. This finding confirmed that the polymers interacted through hydrogen bonding of MW and hydroxyl groups of PVA. The performance of the fabricated nanofibres was investigated for the removal of acidic drugs from spiked water samples. Factors (concentration of acidic drugs, dosage of the nanofibers and contact time) which affect the removal efficiency of the nanofibres were optimised using ultrapure water. Using the nanofibres, 100% removal efficiency for acidic drugs (aspirin, ketoprofen, fenoprofen, diclofenac, and ibuprofen) was achieved. The removal efficiency of the influent wastewater was 76, 89, 97, 93 and 94% for aspirin, ketoprofen, fenoprofen, diclofenac and ibuprofen, respectively, while the removal efficiency of the effluent was 86, 96, 97, 97 and 95% for aspirin, ketoprofen, fenoprofen, diclofenac and ibuprofen, respectively.

Nanoparticle-Based Inhalation Therapy for Pulmonary Diseases

The lung is exposed to various pollutants and is the primary site for the onset of various diseases, including infections, allergies, and cancers. One possible treatment approach for such pulmonary diseases involves direct administration of therapeutics to the lung so as to maintain the topical concentration of the drug. Particles with nanoscale diameters tend to reach the pulmonary region. Nanoparticles (NPs) have garnered significant interest for applications in biomedical and pharmaceutical industries because of their unique physicochemical properties and biological activities. In this article, we describe the biological and pharmacological activities of NPs as well as summarize their potential in the formulation of drugs employed to treat pulmonary diseases. Recent advances in the use of NPs in inhalation chemotherapy for the treatment of lung diseases have also been highlighted.

Ultrasound-assisted fabrication of biopolymer materials: A review

There is an urgent need to develop technologies that can physically manipulate the structure of biocompatible and green polymer materials in order to tune their performance in an efficient, repeatable, easy-to-operate, chemical-free, non-contact, and highly controllable manner. Ultrasound technology produces a cavitation effect that promotes the generation of free radicals, the fracture of chemical chain segments and a rapid change of morphology. The cavitation effects are accompanied by thermal, chemical, and biological effects that interact with the material being studied. With its high efficiency, cleanliness, and reusability applications, ultrasound has a vast range of opportunity within the field of natural polymer-based materials. This work expounds the basic principle of ultrasonic cavitation and analyzes the influence that ultrasonic strength, temperature, frequency and induced liquid surface tension on the physical and chemical properties of biopolymer materials. The mechanism and the influence that ultrasonic modification has on materials is discussed, with highlighted details on the agglomeration, degradation, morphology, structure, and the mechanical properties of these novel materials from naturally derived polymers.

Role of nanocellulose in industrial and pharmaceutical sectors - A review

Lignocellulosic biomass from agricultural residues serves as the critical component to replace synthetic polymeric materials in the coming future. Agricultural residues can be used to obtain cellulose by delignification followed by bleaching. Further, cellulose is converted into nanocellulose by various methods. Nanocellulose is used in multiple pharmaceutical applications as a polymer in hydrogels, transdermal drug delivery systems, aerogels, wound healing dressing materials, as superdisintegrants in fast dissolving tablets, emulgel, microparticles, gels, foams, thickening agents, stabilizers, cosmetics, medical implants, tissue engineering, liposomes, food and composites, etc. This review provides detailed knowledge about the nature of nanocellulose regarding its high surface area, high polymerization, loading, and binding capacity of hydrophilic and hydrophobic active pharmaceutical ingredients and significance of various applications of nanocellulose. Biocompatible and non-toxic, it makes it an ideal material for applications in the biomedical field. A significant advantage is a biocompatibility, which is non-toxic for many biomedical applications.

A review of the berberine natural polysaccharide nanostructures as potential anticancer and antibacterial agents

Despite the promising medicinal properties, berberine (BBR), due to its relatively poor solubility in plasma, low bio-stability and limited bioavailability is not used broadly in clinical stages. Due to these drawbacks, drug delivery systems (DDSs) based on nanoscale natural polysaccharides, are applied to address these concerns. Natural polymers are biodegradable, non-immunogenic, biocompatible, and non-toxic agents that are capable of trapping large amounts of hydrophobic compounds in relatively small volumes. The use of nanoscale natural polysaccharide improves the stability and pharmacokinetics of the small molecules and, consequently, increases the therapeutic effects and reduces the side effects of the small molecules. Therefore, this paper presents an overview of the different methods used for increasing the BBR solubility and bioavailability. Afterwards, the pharmacodynamic and pharmacokinetic of BBR nanostructures were discussed followed by the introduction of natural polysaccharides of plant (cyclodextrines, glucomannan), the shells of crustaceans (chitosan), and the cell wall of brown marine algae (alginate)-based origins used to improve the dissolution rate of poorly soluble BBR and their anticancer and antibacterial properties. Finally, the anticancer and antibacterial mechanisms of free BBR and BBR nanostructures were surveyed. In conclusion, this review may pave the way for providing some useful data in the development of BBR-based platforms for clinical applications.

Guar (Cyamopsis tetragonoloba L.) plant gum: From biological applications to advanced nanomedicine

Natural polymers are an efficient class of eco-friendly and biodegradable polymers, because they are readily available, come from natural sources, inexpensive and can be chemically modified with the correct reagents. Guar gum (GG) is a natural polymer with great potential to be used in pharmaceutical formulations due to its unique composition and lack of toxicity. GG can be designed to suit the needs of the biological and medical engineering sectors. In the development of innovative drug delivery systems, GG is commonly utilized as a rate-controlling excipient. In this review, different properties of GG including chemical composition, extraction methods and its usefulness in diabetes, cholesterol lowering, weight control, tablet formulations as well as its food application were discussed. The other purpose of this study is to evaluate potential use of GG and its derivatives for advanced nanomedicine such as drug delivery, tissue engineering and nanosensing. It should be noted that some applicable patents in medical area have also been included in the rest of this survey to extend knowledge about guar gum and its polymeric nature.

Gum Arabic as an environmentally sustainable polymeric anticorrosive material: Recent progresses and future opportunities

Gum Arabic (GA) is a plant exudate, consisting of glycoproteins (proteins with carbohydrate co-factor or prosthetic group) and polysaccharides mainly consisting of galactose and arabinose. Because of its polymeric nature and tendency to dissolve in water, GA is widely used as anticorrosive materials, especially in the aqueous electrolytes. GA contains various electron rich polar sites through which they easily get adsorbed on metallic surface and behaves as effective anticorrosive materials. Because of its natural and biological origin, GA is regarded as one of the environmental sustainable and edible alternatives to traditional toxic corrosion inhibitors. Present review piece of writing aims to illustrate the assortment of literatures on gum Arabic as a corrosion inhibitor. Limitation of traditional organic corrosion inhibitors and advantages of using GA as an environmental sustainable alternative have also been described along with the mechanism of corrosion inhibition.

A self-matching, ultra-fast film forming and washable removal bio-crosslinked hydrogel films for perishable fruits

Spoilage of food has aggravated the issue of food shortage worldwide. Here, we report a strategy for ultrafast hydrogel film forming within 10 s on fruit surfaces with good self-matching, washable removal and preservative property. This carboxymethyl chitosan (CMCS)/tannic acid (TA) hydrogel film (CTHF) is fabricated by bio-material of CMCS and TA via in-situ rapidly crosslinking with high-density hydrogen bonds. Simply blending TA and CMCS solution at room temperature can form CTHF with different roughness (Ra: ranges from 123 to 1.55 nm) on different fruit surfaces, so as to perfectly match the hydrogel protective layer of pericarp. The CTHF slows down fruit decay by its outstanding antioxidant and antibacterial activity. It is soluble and easily removed (within 3-5 min) by washing without environmental pollution and food safety issues. As natural polymer, CTHF shows high promise as sustainable substitutes for conventional plastics packing because of its non-toxic, edible, biodegradable, and environmentally friendly.

One-step removal of harmful algal blooms by dual-functional flocculant based on self-branched chitosan integrated with flotation function

Harmful algal blooms induce severe environmental problems. It is challenging to remove algae by the current available treatments involving complicate process and costly instruments. Here, we developed a CaO₂@PEG-loaded water-soluble self-branched chitosan (CP-SBC) system, which can remove algae from water in one-step without additional instrumentation. This approach utilizes a novel flocculant (self-branched chitosan) integrated with flotation function (induced by CaO₂@PEG). CP-SBC exhibited better flocculation performance than commercial flocculants, which is attributed to the enhanced bridging and sweeping effect of branched chitosan. CP-SBC demonstrated outstanding biocompatibility, which was verified by zebrafish test and algae activity test. CaO₂@PEG-loaded self-branched chitosan can serve as an "Air flotation system" to spontaneous float the flocs after flocculation by sustainably released O₂. Furthermore, CP-SBC can improve water quality through minimizing dissolved oxygen depletion and reducing total phosphorus concentrations.

Processing, mechanical properties and bio-applications of silk fibroin-based high-strength hydrogels

Hydrogels are an attractive class of materials that possess similar structural and functional characteristics to wet biological tissues and demonstrate a diversity of applications in biomedical engineering. Silk fibroin (SF) is a unique natural polymer due to its fibrous protein nature, versatile formats, biocompatibility, tunable biodegradation and is thus a good hydrogel candidate for bio-applications. Compared to synthetic polymer hydrogels, poor mechanical performance is still a fatal drawback that hinders the application of SF hydrogels as structural materials. Researchers have attempted to develop strategies to construct silk fibroin-based high-strength hydrogels (SF-HSHs). Herein, we firstly provide an overview of the approaches of processing SF-HSHs with a focus on the physical/non-covalent crosslinking mechanisms. The examples of SF-HSHs are discussed in detail under four categories, including physical-crosslinked, dual-crosslinked, double network and composite hydrogels respectively. A brief section follows to elucidate on the gelation mechanisms of SF-HSHs before a description of the utility of SF-HSHs in biomedicine and devices is presented. Finally, the potential challenges and future development of SF-HSHs are briefly discussed. This review aims to enhance our understanding of the structure-mechanical property-function relationships of soft materials made from natural polymers and guide future research of silk fibroin-based hydrogels for biomedical applications. STATEMENT OF SIGNIFICANCE: Silk fibroin (SF) extracted from silk fibres is increasingly applied in the biomedical field, and SF hydrogel has been an emerging area for frontier bio-research. Since SF biopolymer has an intrinsic tendency to form regular β-sheet stacks, it can be processed into purely physically crosslinked hydrogels, thus avoiding the use of chemical crosslinkers. Nevertheless, akin to other natural polymers, lab-produced SF is variable (i.e. the molecular weight and distribution), and the gelation of SF hydrogel is challenging to control. In addition, hydrogels made from SF are usually weak and brittle, which hinders the wide use of this biofriendly and biodegradable hydrogel. Recently, there is a pressing need for high strength hydrogels from natural polymers for biomedical applications, and SF is proposed as a strong candidate. Therefore, we have studied the literature in the past 10 years and would like to focus on the gelation mechanism and mechanical strength of SF hydrogels for the review.

Design and Characterization of Biomimetic Kerateine Aerogel-Electrospun Polycaprolactone Scaffolds for Retinal Cell Culture

Age-related macular degeneration (AMD) is a retinal disease that affects 196 million people and causes nearly 9% of blindness worldwide. While several pharmacological approaches slow the effects of AMD, in our opinion, cell-based strategies offer the most likely path to a cure. We describe the design and initial characterization of a kerateine (obtained by reductive extraction from keratin proteins) aerogel-electrospun polycaprolactone fiber scaffold system. The scaffolds mimic key features of the choroid and the Bruch's membrane, which is the basement membrane to which the cells of the retinal pigment epithelium (RPE) attach. The scaffolds had elastic moduli of 2-7.2 MPa, a similar range as native choroid and Bruch's membrane. ARPE-19 cells attached to the polycaprolactone fibers, remained viable for one week, and proliferated to form a monolayer reminiscent of that needed for retinal repair. These constructs could serve as a model system for testing cell and/or drug treatment strategies or directing ex vivo retinal tissue formation in the treatment of AMD.

Tea eggs-inspired high-strength natural polymer hydrogels

Natural polymer (NP) hydrogels are an irreplaceable class of biomaterials owing to their identified biosafety; however, the intrinsic poor mechanical strengths severely limit their applications as structural tissue engineering scaffolds. Inspired by the stiffening albumen gel of tea eggs, a traditional Chinese snack, high-strength NP hydrogels are constructed by simply soaking in aqueous solution of tea polyphenols (TP), an active ingredient extracted from tea. The TP-treated representative NP hydrogels exhibit considerably enhanced multifaceted mechanical properties with maximum 19-/30-, 8.4-, 6.1-, 72-fold increases in tensile/compressive strengths, Young's modulus, elongation at break and facture toughness, respectively, compared with pristine hydrogels, primarily due to the hydrogen bonding interactions between TP and NP chains. The TP-treated NP hydrogels can resist different large deformations, which cannot be achieved by their original species at all. In aqueous solution, the TP-treated NP hydrogels can still maintain robust mechanical performances, in spite of somewhat decline in strengths with release of TP, which just favorably affords increased water contents, antibacterial and antioxidant activities. GelMA-TP hydrogel is shown to facilitate wound healing in a full-thickness skin defect model. Importantly, the weak 3D printed GelMA scaffolds are significantly strengthened by TP treatment, broadening the possibility for customizing individualized bioscaffolds.

•

Tea eggs-inspired high-strength natural polymer (NP) hydrogels are prepared.

•

Tea polyphenols strengthen considerably 3D-printed NP hydrogel scaffolds.

•

The NP-TP hydrogels exhibit antibacterial and antioxidant activities.

Construction of natural polymeric imprinted materials and their applications in water treatment: A review

Molecularly imprinted materials (MIMs) have been widely used in various fields, including water treatment, chemical sensing, and biotechnology, because of their specific recognition and high selectivity. MIMs are usually obtained via two successive steps, namely, (1) copolymerization and crosslinking reactions of the preassembled complex of comonomers and a specific target compound (2) and thorough removal of template molecules. Some functional polymers are directly used as supporting materials and functional groups assembled with target compound are provided to simplify the preparation of MIMs. Natural polymers, such as chitosan, cyclodextrin, sodium alginate, starch, cellulose, lignin and their derivatives, are good candidates because of their environmentally friendly properties, low costs, and abundant active functional groups. In this study, different methods for the preparation of natural polymeric MIMs were reviewed in terms of the construction of microscopic binding cavities and macroscopic visible condensed structures with different shapes. Natural polymeric MIMs in water treatment applications, such as adsorption and detection of various pollutants from aqueous solutions, were summarized. Prospects on the development of novel and high-performance natural polymeric MIMs were discussed to overcome the difficulties in their preparation and applications.

Biomaterials and strategies for repairing spinal cord lesions

Spinal cord injury (SCI) causes intractable disease and leads to inevitable physical, financial, and psychological burdens on patients and their families. SCI is commonly divided into primary and secondary injury. Primary injury occurs upon direct impact to the spinal cord, which leads to cell necrosis, axon disruption, and vascular loss. This triggers pathophysiological secondary injury, which has several phases: acute, subacute, intermediate, and chronic. These phases are dependent on post-injury time and pathophysiology and have various causes, such as the infiltration of inflammatory cells and release of cytokines that can act as a barrier to neural regeneration. Another unique feature of SCI is the glial scar produced from the reactive proliferation of astrocytes, which acts as a barrier to axonal regeneration. Interdisciplinary research is investigating the use of biomaterials and tissue-engineered fabrication to overcome SCI. In this review, we discuss representative biomaterials, including natural and synthetic polymers and nanomaterials. In addition, we describe several strategies to repair spinal cord injuries, such as fabrication and the delivery of therapeutic biocomponents. These biomaterials and strategies may offer beneficial information to enhance the repair of spinal cord lesions.

Polysaccharides and proteins-based nanogenerator for energy harvesting and sensing: A review

Nanogenerator is a promising energy harvesting device that can scavenge tiny mechanical energy from the surrounding environment, and then convert it into electricity. Natural bio-polymers are the potential candidates for the design of nanogenerators due to their excellent characteristics like piezoelectricity, triboelectricity, non-toxicity, biocompatibility and biodegradability. Especially, nanogenerators using bio-sourced polymers as the core raw materials are suitable for wearable and implantable devices. In this review, major advancements in the sensing field of nanogenerators based on natural polysaccharides and proteins (cellulose, chitosan, alginate, agarose, starch, lignin, silk fibroin, collagen, gelatin, keratin, peptide, M13 bacteriophage, β-cyclodextrin, spider silk, etc.) are summarized. Also, challenges in the improvement of electric output performance, flexibility, anti-humidity and energy management for natural polymers based-nanogenerators are proposed. In the future, they will be applied in daily life as an alternative for traditional power source after addressing issues mentioned above.

Effect of green tea extract on gelatin-based films incorporated with lemon essential oil

The use of natural polymers, such as gelatin and other proteins, has increased in an attempt to replace part of the consumption of petroleum-based packaging. This study evaluated the influence of green tea extract and lemon nanoemulsion on mechanical, thermal and permeability properties of gelatin matrix. The results showed that green tea increased the gelatin tensile strength (TS) from 86 ± 7 MPa to 101 ± 5 MPa, on the other hand, the nanoemulsion decreases to 78 ± 8 MPa. The incorporation of green tea and nanoemulsion enhanced the water vapor permeability of gelatin film; this could be due to the interacting with the hydrophobic domains of gelatin. This was indicated by melting point (Tm) in differential scanning calorimetry (DSC) and degradation temperatures in the thermogravimetric analysis (TG), respectively. Changes in FTIR spectra of gelatin film were observed when the green tea and nanoemulsion were incorporated. Therefore, this study showed a new characterization and formulation of gelatin films incorporated by green tea extract and lemon nanoemulsion and their potential for edible film.

Transparent floatable magnetic alginate sphere used as photocatalysts carrier for improving photocatalytic efficiency and recycling convenience

Practical application of powder photocatalysts is far from satisfying due to their low photon utilization, inconvenient recovery and potential environmental risk. In this study, an easily recoverable, environmentally friendly and highly transparent floatable magnetic photocatalyst carrier was prepared based on biopolymer alginate and Fe₃O₄ particles. Further, three different types of photocatalysts were chosen as model semiconductor photocatalysts and loaded on the shell of the carriers. The freeze process facilitated the formation of internal cavities that enhanced floating ability and transparency of the spheres. Meanwhile, the excellent floating performance offered massive reaction sites for pollutants reacting with photocatalysts, O₂ and photons on the air/water interface. Photodegradation results showed all three floatable hybrid photocatalysts exhibited enhanced photocatalytic efficiencies compared to the virgin photocatalysts. In short, the carrier can integrate excellent floating ability, environmental friendliness and full recycling with good stability, and it can greatly improve the photocatalytic efficiency of various powder semiconductor photocatalysts.

Keratin - Based materials for biomedical applications

Keratin constitutes the major component of the feather, hair, hooves, horns, and wool represents a group of biological material having high cysteine content (7-13%) as compared to other structural proteins. Keratin -based biomaterials have been investigated extensively over the past few decades due to their intrinsic biological properties and excellent biocompatibility. Unlike other natural polymers such as starch, collagen, chitosan, the complex three-dimensional structure of keratin requires the use of harsh chemical conditions for their dissolution and extraction. The most commonly used methods for keratin extraction are oxidation, reduction, steam explosion, microbial method, microwave irradiation and use of ionic liquids. Keratin -based materials have been used extensively for various biomedical applications such as drug delivery, wound healing, tissue engineering. This review covers the structure, properties, history of keratin research, methods of extraction and some recent advancements related to the use of keratin derived biomaterials in the form of a 3-D scaffold, films, fibers, and hydrogels.

Spider (Linothele megatheloides) and silkworm (Bombyx mori) silks: Comparative physical and biological evaluation

Silks, in particular silkworm silks, have been studied for decades as possible candidate materials for biomedical applications. Recently, great attentions have been paid to spider silks, mainly due to their unique and remarkable mechanical properties. Both materials express singular interactions with cells through specific biorecognition moieties on the core proteins making up the two silks. In this work, the silk from a Colombian spider, Linothele megatheloides (LM), which produces a single type of silk in a relatively large amount, was studied in comparison with silk from Bombyx mori silkworm, before and after degumming, with the evaluation of their chemical, mechanical and biological properties. Unexpected biological features in cell culture tests were found for the LM silk already at very early stage, so suggesting further investigation to explore its use for tailored biomedical applications.

Synthesis and characterization of magnetite/Alyssum homolocarpum seed gum/Ag nanocomposite and determination of its antibacterial activity

Due to applications of silver nanoparticles (Ag NPs) especially in advanced science fields, it is important to produce Ag antibacterial nanocomposites with enhanced antibacterial activity and reusability. Over the past decade researches about natural polymers have emphasized the use of them as nanoparticles coating. In this work, a novel core-shell antibacterial agent was synthesized through a three-step procedure. Fe₃O₄ nanoparticles (Fe₃O₄ NPs) were synthesized and coated with a natural polymer called Alyssum homolocarpum seed gum (AHSG). Ag NPs were immobilized on the AHSG resulting in formation of the new nanocomposite with improved antimicrobial properties. The immobilization of Ag NPs prevents the release of toxic Ag⁺ ions. The Fe₃O₄@AHSG@Ag nanocomposite could easily be separated from medium using an external magnetic field due to presence of the Fe₃O₄ superparamagnetic nanoparticles. The as-synthesized nanocomposite was characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy, X-ray diffraction, vibrating sample magnetometer and dynamic light scattering. The results showed that the magnetic nanocomposite was synthesized and coated successfully. Finally, results of disk diffusion method demonstrated that the nanocomposite exhibits excellent antibacterial activity against gram-positive and gram-negative bacteria.

Plant tannin immobilized Fe3O4@SiO2 microspheres: A novel and green magnetic bio-sorbent with superior adsorption capacities for gold and palladium

In this paper, a new core-shell nanostructured magnetic bio-based composite was prepared by immobilizing persimmon tannin (PT) onto Fe₃O₄@SiO₂ microspheres, and the as designed Fe₃O₄@SiO₂@PT was utilized for adsorptive recovery of Au(III) and Pd(II). The preparation, morphology, composition and magnetic property of Fe₃O₄@SiO₂@PT were characterized. Adsorption parameters of Fe₃O₄@SiO₂@PT towards Au(III) and Pd(II) including initial pH, reaction time, initial concentration of metal ions, effect of acidity and interference of coexisting metal ions were investigated. It is sufficiently confirmed that silica was coated on Fe₃O₄ and persimmon tannin was immobilized on aminated Fe₃O₄@SiO₂. The thickness of silica and loaded persimmon tannin are around 18 nm and 14 nm, respectively. With only 1.00 wt% of persimmon tannin, however, the maximum adsorption capacities of Fe₃O₄@SiO₂@PT for Au(III) and Pd(II) were as high as 917.43 and 196.46 mg·g^-1, respectively. In addition, after adsorption of Au(III) and Pd(II), the magnetization saturation values (Ms) of Fe₃O₄@SiO₂@PT were high enough to guarantee efficient magnetic seperation. Metallic gold could be facilely recovered from wastewaters containing Au(III).

Polymer materials for prevention of postoperative adhesion

Postoperative adhesion (POA) is a common complication that often occurs after a variety of surgeries, such as plastic surgery, repair operations of abdominal, pelvic, and tendon, and so forth. Moreover, POA leads to chronic abdominal pain, secondary infertility in women, intestinal obstruction, and other severe complications, which significantly reduce the life quality of patients. In order to prevent the formation of POA, a number of strategies have been developed, among which an emerging method is physical barriers consisting of polymer materials. This review highlights the most commonly used natural and synthetic polymer materials in anti-adhesion physical barriers. The specific features of polymer materials are analyzed and compared, and the possible prospect is also predicted.

STATEMENT OF SIGNIFICANCE

Postoperative adhesion (POA) is a serious complication accompanied with various surgeries. Polymer material-based physical barriers have attracted a large amount of attention in POA prevention. The polymer barriers can effectively avoid the formation of fibrous tissues among normal organs by reducing the interconnection of injured tissues. In this review, specific features of the natural and synthetic polymer materials for application in POA prevention were presented, and the possible prospects were predicted. All in all, our work can provide inspiration for researchers to choose proper polymer materials for preclinical and even clinical anti-adhesion studies.

Reutilization of discarded biomass for preparing functional polymer materials

Biomass is abundant and recyclable on the earth, which has been assigned numerous roles to human beings. However, over the past decades, accompanying with the rapid expansion of man-made materials, such as alloy, plastic, synthetic rubber and fiber, a great number of natural materials had been neglected and abandoned, such as straw, which cause a waste of resource and environmental pollution. In this review, based on introducing sources of discarded biomass, the main composition and polymer chains in discarded biomass materials, the traditional treatment and novel approach for reutilization of discarded biomass were summarized. The discarded biomass mainly come from plant wastes generated in the process of agriculture and forestry production and manufacturing processes, animal wastes generated in the process of animal husbandry and fishery production as well as the residual wastes produced in the process of food processing and rural living garbage. Compared with the traditional treatment including burning, landfill, feeding and fertilizer, the novel approach for reutilization of discarded biomass principally allotted to energy, ecology and polymer materials. The prepared functional materials covered in composite materials, biopolymer based adsorbent and flocculant, carrier materials, energy materials, smart polymer materials for medical and other intelligent polymer materials, which can effectively serve the environmental management and human life, such as wastewater treatment, catalyst, new energy, tissue engineering, drug controlled release, and coating. To sum up, the renewable and biodegradable discarded biomass resources play a vital role in the sustainable development of human society, as well as will be put more emphases in the future.

Polymers in our daily life

Polymers are widely used advanced materials, which are found almost in every material used in our daily life. To date, the importance of polymers has been much more highlighted because of their applications in different dominions of sciences, technologies and industry – from basic uses to biopolymers and therapeutic polymers. The main aim of this editorial is to accentuate the pragmatic impacts of polymers in human daily life.

Surface-mediated delivery of siRNA from fibrin hydrogels for knockdown of the BMP-2 binding antagonist noggin

Antagonists and inhibitory molecules responsible for maintaining tissue homeostasis can present a significant barrier to healing when tissue engineering/regenerative medicine strategies are employed. One example of this situation is the up-regulation of antagonists such as noggin in response to increasing concentrations of bone morphogenetic protein-2 (BMP-2) present from endogenous bone repair processes or delivered exogenously from biomaterials (synthetic bone grafts). While recombinant human (rh)BMP-2 delivered from synthetic bone grafts has been shown to be an effective alternative to autografts and allografts, the supraphysiological doses of rhBMP-2 have led to clinically-adverse side effects. The high rhBMP-2 dosage may be required, in part, to overcome the presence of antagonists such as noggin. Small interfering RNA (siRNA) is an appealing approach to overcome this problem because it can knock-down antagonists or inhibitory molecules in a temporary manner. Here, we conducted fundamental studies on the delivery of siRNA from material surfaces as a means to knock-down antagonists like noggin. Non-viral cationic lipid (Lipofectamine)-siRNA complexes were delivered from a fibrin hydrogel surface to MC3T3-E1 preosteoblasts that were treated with a supraphysiological dose of rhBMP-2 to achieve noggin mRNA expression levels higher than cells naïve to rhBMP-2. Confocal microscopy and flow cytometry showed intracellular uptake of siRNA in over 98% of MC3T3-E1 cells after 48 h. Doses of 0.5 and 1 μg noggin siRNA were able to significantly reduce noggin mRNA to levels equivalent to those in MC3T3-E1 cells not exposed to rhBMP-2 with no effects on cell viability.

STATEMENT OF SIGNIFICANCE

Small interfering RNA (siRNA) has been considered for treatment of diseases ranging from Alzheimer's to cancer. However, the ability to use siRNA in conjunction with biomaterials to direct tissue regeneration processes has received relatively little attention. Using the bone morphogenetic protein 2 antagonist, noggin, as a model, this research describes an approach to knock-down molecules that are inhibitory to desired regenerative pathways at the mRNA level via siRNA delivery from a hydrogel surface. Interactions between the material (fibrin) surface and polycation-siRNA complexes, release of the siRNA from the material surface, high levels of cellular uptake/internalization of siRNA, and significant knockdown of the targeting (noggin) mRNA are demonstrated. Broader future applications include those to nerve regeneration, cardiovascular tissue engineering, directing (stem) cell behavior, and mitigating inflammatory responses to materials.