Microdroplet-guided intercalation and deterministic delamination towards intelligent rolling origami

Multilevel design and construction in nanomembrane rolling for three-dimensional angle-sensitive photodetection

Releasing pre-strained two-dimensional nanomembranes to assemble on-chip three-dimensional devices is crucial for upcoming advanced electronic and optoelectronic applications. However, the release process is affected by many unclear factors, hindering the transition from laboratory to industrial applications. Here, we propose a quasistatic multilevel finite element modeling to assemble three-dimensional structures from two-dimensional nanomembranes and offer verification results by various bilayer nanomembranes. Take Si/Cr nanomembrane as an example, we confirm that the three-dimensional structural formation is governed by both the minimum energy state and the geometric constraints imposed by the edges of the sacrificial layer. Large-scale, high-yield fabrication of three-dimensional structures is achieved, and two distinct three-dimensional structures are assembled from the same precursor. Six types of three-dimensional Si/Cr photodetectors are then prepared to resolve the incident angle of light with a deep neural network model, opening up possibilities for the design and manufacturing methods of More-than-Moore-era devices.

Self-Rolled-Up Ultrathin Single-Crystalline Silicon Nanomembranes for On-Chip Tubular Polarization Photodetectors

Freestanding single-crystalline nanomembranes and their assembly have broad application potential in photodetectors for integrated chips. However, the release and self-assembly process of single-crystalline semiconductor nanomembranes still remains a great challenge in on-chip processing and functional integration, and photodetectors based on nanomembrane always suffer from limited absorption of nanoscale thickness. Here, a non-destructive releasing and rolling process is employed to prepare tubular photodetectors based on freestanding single-crystalline Si nanomembranes. Spontaneous release and self-assembly are achieved by residual strain introduced by lattice mismatch at the epitaxial interface of Si and Ge, and the intrinsic stress and strain distributions in self-rolled-up Si nanomembranes are analyzed experimentally and computationally. The advantages of light trapping and wide-angle optical coupling are realized by tubular geometry. This Si microtube device achieves reliable Ohmic contact and exhibits a photoresponsivity of over 330 mA W-1 , a response time of 370 µs, and a light incident detection angle range of over 120°. Furthermore, the microtubular structure shows a distinct polarization angle-dependent light absorption, with a dichroic ratio of 1.24 achieved at 940 nm. The proposed Si-based microtubes provide new possibilities for the construction of multifunctional chips for integrated circuit ecosystems in the More than Moore era.

Inflatable Metamorphic Origami

This study created a new type of inflatable metamorphic origami that has the advantage of being a highly simplified deployable system capable of realizing multiple sequential motion patterns with a monolithic actuation. The main body of the proposed metamorphic origami unit was designed as a soft inflatable metamorphic origami chamber with multiple sets of contiguous/collinear creases. In response to pneumatic pressure, the metamorphic motions are characterized by an initial unfolding around the first set of contiguous/collinear creases followed by another unfolding around the second set of contiguous/collinear creases. Furthermore, the effectiveness of the proposed approach was verified by constructing a radial deployable metamorphic origami for supporting the deployable planar solar array, a circumferential deployable metamorphic origami for supporting the deployable curved-surface antenna, a multi-fingered deployable metamorphic origami grasper for grasping large-sized objects, and a leaf-shaped deployable metamorphic origami grasper for capturing heavy objects. The proposed novel metamorphic origami is expected to serve as a foundation for designing lightweight, high-deploy/fold-ratio, low-energy-consumption space deployable systems.

Self-rolling of vanadium dioxide nanomembranes for enhanced multi-level solar modulation

Thermochromic window develops as a competitive solution for carbon emissions due to comprehensive advantages of its passivity and effective utilization of energy. How to further enhance the solar modulation ([Formula: see text]) of thermochromic windows while ensuring high luminous transmittance ([Formula: see text]) becomes the latest challenge to touch the limit of energy efficiency. Here, we show a smart window combining mechanochromism with thermochromism by self-rolling of vanadium dioxide (VO₂) nanomembranes to enhance multi-level solar modulation. The mechanochromism is introduced by the temperature-controlled regulation of curvature of rolled-up smart window, which benefits from effective strain adjustment in VO₂ nanomembranes upon the phase transition. Under geometry design and optimization, the rolled-up smart window with high [Formula: see text] and [Formula: see text] is achieved for the modulation of indoor temperature self-adapted to seasons and climate. Furthermore, such rolled-up smart window enables high infrared reflectance after triggered phase transition and acts as a smart lens protective cover for strong radiation. This work supports the feasibility of self-rolling technology in smart windows and lens protection, which promises broad interest and practical applications of self-adapting devices and systems for smart building, intelligent sensors and actuators with the perspective of energy efficiency.

Collective Coupling of 3D Confined Optical Modes in Monolithic Twin Microtube Cavities Formed by Nanomembrane Origami

We report the monolithic fabrication of twin microtube cavities by a nanomembrane origami method for achieving collective coupling of 3D confined optical modes. Owing to the well-aligned twin geometries, two sets of 3D confined optical modes in twin microtubes are spectrally and spatially matched, by which both the fundamental and higher-order axial modes are respectively coupled with each other. Multiple groups of the coupling modes provide multiple effective channels for energy exchange between coupled microcavities illustrated by the measured spatial optical field distributions. The spectral anticrossing and changing-over features of each group of coupled modes are revealed in experiments and calculations, indicating the occurrence of strong coupling. In addition, the simulated 3D mode profiles of twin microcavities confirm the collective strong coupling behavior, which shows good agreement with experiments. The collective coupling of 3D confined resonant modes promises broad applications in multichannel optical signal processing, nanophotonics, and 3D non-Hermitian systems.

Rational Design of Polymer Conical Nanoswimmers with Upstream Motility

Utilizing bottom-up controllable molecular assembly, the bio-inspired polyelectrolyte multilayer conical nanoswimmers with gold-nanoshell functionalization on different segments are presented to achieve the optimal upstream propulsion performance. The experimental investigation reveals that the presence of the gold nanoshells on the big openings of the nanoswimmers could not only bestow efficient directional propulsion but could also minimize the impact from the external flow. The gold nanoshells at the big openings of nanoswimmers facilitate the acoustically powered propulsion against a flow velocity of up to 2.00 mm s^-1, which is higher than the blood velocity in capillaries and thus provides a proof-of-concept design for upstream nanoswimmers.

Solvent-Free Preparation of Closely Packed MoS2 Nanoscrolls for Improved Photosensitivity

Due to their enhanced light absorption efficiency, one-dimensional (1D) transition metal dichalcogenide (TMDC) nanoscrolls derived from two-dimensional (2D) TMDC nanosheets have shown excellent optoelectronic properties. Currently, organic solvent and alkaline droplet-assisted scrolling methods are popular for preparing TMDC nanoscrolls. Unfortunately, the adsorption of organic solvent or alkaline impurities on TMDC is inevitable during the preparation, which affects the optoelectronic properties of TMDC. In this work, we report a solvent-free method to prepare closely packed MoS₂ nanoscrolls by dragging a deionized water droplet onto the chemical vapor deposition grown monolayer MoS₂ nanosheets at 100 °C (referred to as MoS₂ NS-W). The as-prepared MoS₂ NS-W was well characterized by optical microscopy, atomic force microscopy, and ultralow frequency (ULF) Raman spectroscopy. After high temperature annealing, the height of MoS₂ nanoscrolls prepared using an ethanol droplet (referred to as MoS₂ NS-E) greatly decreased, indicating the loss of encapsulated ethanol in MoS₂ NS-E. While the height of MoS₂ NS-W was almost unchanged under the same conditions, implying that no water was embedded in the scroll. Compared to the MoS₂ NS-E, the MoS₂ NS-W shows more ULF breathing mode peaks, confirming the stronger interlayer interaction. In addition, the MoS₂ NS-W shows a higher Young's modulus than MoS₂ NS-E, which could arise from the closely packed scroll structure. Importantly, the MoS₂ NS-W device showed a photosensitivity 1 order of magnitude higher than that of the MoS₂ NS-E device under blue, green, and red lasers, respectively. The decreased photosensitivity of MoS₂ NS-E was attributed to the larger dark current, which might be assigned to the adsorbed ethanol between the adjacent layers in MoS₂ NS-E. Our work provides a solvent-free method to prepare closely packed MoS₂ nanoscrolls at large scale and demonstrates their great potential for high-performance optoelectronic devices.

Self-Rolling of Monolayer Graphene for Ultrasensitive Molecular Sensing

The controllable manipulation of graphene to create three-dimensional (3D) structures is an intriguing approach for favorably tuning its properties and creating new types of 3D devices. However, due to extremely low bending stiffnesses, it is rather challenging to construct monolayer graphene into stable 3D structures. Here, we demonstrate the stable formation of monolayer graphene microtubes with accompanying pre-patterned strain layers. The diameter of graphene microtubes can be effectively tuned by changing the thickness of the strain layers. Benefiting from a high surface-to-volume ratio of the tubular geometry, the 3D geometry leads to a prominent Raman enhancement, which was further applied to molecular sensing. The R6G molecules on graphene microtubes can be detected even for a concentration as low as 10^-11 M. We believe that this method can be a generalized way to realize the 3D tubular structure of other 2D materials.

Intelligent Shape-Morphing Micromachines

Intelligent machines are capable of switching shape configurations to adapt to changes in dynamic environments and thus have offered the potentials in many applications such as precision medicine, lab on a chip, and bioengineering. Even though the developments of smart materials and advanced micro/nanomanufacturing are flouring, how to achieve intelligent shape-morphing machines at micro/nanoscales is still significantly challenging due to the lack of design methods and strategies especially for small-scale shape transformations. This review is aimed at summarizing the principles and methods for the construction of intelligent shape-morphing micromachines by introducing the dimensions, modes, realization methods, and applications of shape-morphing micromachines. Meanwhile, this review highlights the advantages and challenges in shape transformations by comparing micromachines with the macroscale counterparts and presents the future outlines for the next generation of intelligent shape-morphing micromachines.

Insights into Regional Wetting Behaviors of Amphiphilic Collagen for Dual Separation of Emulsions

Industrial manufacture generates a huge quantity of emulsion wastewater, which causes serious threats to the aquatic ecosystems. Water-in-oil (W/O) and oil-in-water (O/W) emulsions are two major types of emulsions discharged by industries. However, dual separation of W/O and O/W emulsions remains a challenging issue due to the contradictory permselectivity for separating the two emulsions. In the present investigation, the amphiphilicity-derived regional wetting mechanism of water and oil on the amphiphilic collagen fibers was revealed based on the combination of numerous experiments and molecular dynamics (MD) simulations. Electrostatic interactions and van der Waals force were manifested to be the driving forces of regional wetting in the hydrophilic and hydrophobic regions, respectively. The regional wetting endowed amphiphilic collagen fibers with underwater oleophobicity and underoil hydrophilicity, which enabled dual separation of emulsions by selectively retaining the dispersed water phase of W/O emulsions in the hydrophilic regions while the dispersed oil phase of O/W emulsions in the hydrophobic regions. The achieved separation efficiency was higher than 99.98%, and the flux reached 3337.6 L m^-2 h^-1. Initial wetting status significantly affects the regional wetting-enabled dual separation. Based on the MD simulations, amphiphilic intramolecular conformations of tropocollagen were suggested to be the origins of regional wetting on collagen fibers. Our findings may pave the way for developing high-performance dual separation materials that are promising to be utilized for the practical treatment of emulsion wastewater.

Self-propelled torus colloids

Suspensions of chemically powered self-propelled colloidal particles are examples of active matter systems with interesting properties. While simple spherical Janus particles are often studied, it is known that geometry is important and recent experiments have shown that chemically active torus-shaped colloids behave differently from spherical colloids. In this paper, coarse-grained microscopic simulations of the dynamics of self-diffusiophoretic torus colloids are carried out in bulk solution in order to study how torus geometric factors influence their active motion. The concentration and velocity fields are key ingredients in self-diffusiophoretic propulsion, and the forms that these fields take in the colloid vicinity are shown to be strong functions of torus geometric parameters such as the torus hole size and thickness of the torus tube. This work utilizes a method where self-diffusiophoretic torus colloids with various geometric and dynamical characteristics can be built and studied in fluid media that include chemical reactions and fluid flows. The model can be used to investigate the collective properties of these colloids and their dynamics in confined systems, topics that are of general importance for applications that use colloidal motors with complex geometries.

Hotspots on the Move: Active Molecular Enrichment by Hierarchically Structured Micromotors for Ultrasensitive SERS Sensing

Surface-enhanced Raman scattering (SERS) is recognized as one of the most sensitive spectroscopic tools for chemical and biological detections. Hotspots engineering has expedited promotion of SERS performance over the past few decades. Recently, molecular enrichment has proven to be another effective approach to improve the SERS performance. In this work, we propose a concept of "motile hotspots" to realize ultrasensitive SERS sensing by combining hotspots engineering and active molecular enrichment. High-density plasmonic nanostructure-supporting hotspots are assembled on the tubular outer wall of micromotors via nanoimprint and rolling origami techniques. The dense hotspots carried on these hierarchically structured micromotors (HSMs) can be magnet-powered to actively enrich molecules in fluid. The active enrichment manner of HSMs is revealed to be effective in accelerating the process of molecular adsorption. Consequently, SERS intensity increases significantly because of more molecules being adjacent to the hotspots after active molecular enrichment. This "motile hotspots" concept provides a synergistical approach in constructing a SERS platform with high performance. Moreover, the newly developed construction method of HSMs manifests the possibility of tailoring tubular length and diameter as well as surface patterns on the outer wall of HSMs, demonstrating good flexibility in constructing customized micromotors for various applications.