Inhibition of defect-induced α-to-δ phase transition for efficient and stable formamidinium perovskite solar cells

Unveiling the Effect of Cooling Rate on Grown-in Defects Concentration in Polycrystalline Perovskite Films for Solar Cells with Improved Stability

Numerous efforts are devoted to reducing the defects at perovskite surface and/or grain boundary; however, the grown-in defects inside grain is rarely studied. Here, the influence of cooling rate on the point defects concentration in polycrystalline perovskite film during heat treatment processing is investigated. With the combination of theoretical and experimental studies, this work reveals that the supersaturated point defects in perovskite films generate during the cooling process and its concentration improves as the cooling rate increases. The supersaturated point defects can be minimized through slowing the cooling rate. As a result, the optimized FAPbI3 polycrystalline films achieve a superior carrier lifetime of up to 12.6 µs and improved stability. The champion device delivers a 25.47% PCE (certified 24.7%) and retain 90% of their initial value after >1100 h of operation at the maximum power point. These results provide a fundamental understanding of the mechanisms of grown-in defects formation in polycrystalline perovskite film.

Interface Passivation of a Pyridine-Based Bifunctional Molecule for Inverted Perovskite Solar Cells

Organic-inorganic hybrid perovskite solar cells (PSCs) have recently been demonstrated to be promising renewable harvesters because of their prominent photovoltaic power conversion efficiency (PCE), although their stability and efficiency still have not reached commercial criteria. Trouble-oriented analyses showcase that defect reduction among the grain boundaries and interfaces in the prepared perovskite polycrystalline films is a practical strategy, which has prompted researchers to develop functional molecules for interface passivation. Herein, the pyridine-based bifunctional molecule dimethylpyridine-3,5-dicarboxylate (DPDC) was employed as the interface between the electron-transport layer and perovskite layer, which achieved a champion PCE of 21.37% for an inverted MAPbI3-based PSC, which was greater than 18.64% for the control device. The mechanistic studies indicated that the significantly improved performance was mainly attributed to the remarkably enhanced fill factor with a value greater than 83%, which was primarily due to the nonradiative recombination suppression offered by the passivation effect of DPDC. Moreover, the promoted carrier mobility together with the enlarged crystal size contributed to a higher short-circuit current density. In addition, an increase in the open-circuit voltage was also observed in the DPDC-treated PSC, which benefited from the improved work function for reducing the energy loss during carrier transport. Furthermore, the DPDC-treated PSC showed substantially enhanced stability, with an over 80% retention rate of its initial PCE value over 300 h even at a 60% relative humidity level, which was attributed to the hydrophobic nature of the DPDC molecule and effective defect passivation. This work is expected not only to serve as an effective strategy for using a pyridine-based bifunctional molecule to passivate perovskite interfaces to enhance photovoltaic performance but also to shed light on the interface passivation mechanism.

Influence of F-Containing Materials on Perovskite Solar Cells

Perovskite solar cells (PSCs) are usually modified and passivated to improve their performance and stability. The interface modification and bulk doping are the two basic strategies. Fluorine (F)-containing materials are highly favored because of their unique hydrophobicity and coordination ability. This review discusses the basic characteristics of F, and the basic principles of improving the photovoltaic performance and stability of PSC devices using F-containing materials. We systematically summarized the latest progress in the application of F-containing materials to achieve efficient and stable PSCs on several key interface layers. It is believed that this work will afford significant understanding and inspirations toward the future application directions of F-containing materials in PSCs, and provide profound insights for the development of efficient and stable PSCs.

Influence of Donor Skeleton on Intramolecular Electron Transfer Amount for Efficient Perovskite Solar Cells

The passivation of the defects derived from rapid-crystallization with electron-donating molecules is always a prerequisite to obtain desirable perovskite films for efficient and stable solar cells, thus, the in-depth understanding on the correlations between molecular structure and passivation capacity is of great importance for screening passivators. Here, we introduce the double-ended amide molecule into perovskite precursor solution to modulate crystallization process and passivate defects. By regulating the intermediate bridging skeletons with alkyl, alkenyl and benzene groups, the results show the passivation strength highly depends on the spin-state electronic structure that serves as an intrinsic descriptor to determine the intramolecular charge distribution by controlling orbital electron transfer from the donor segment to acceptor segment. Upon careful optimization, the benzene-bridged amide molecule demonstrates superior efficacy on improving perovskite film quality. As a physical proof-of-concept, the carbon-based, all-inorganic CsPbI2Br solar cell delivers a significantly increased efficiency of 15.51 % with a remarkably improved stability. Based on the same principle, a champion efficiency of 24.20 % is further obtained on the inverted (Cs0.05MA0.05FA0.9)Pb(I0.93Br0.07)3 solar cell. These findings provide new fundamental insights into the influence of spin-state modulation on effective perovskite solar cells.

Elimination of Intragrain Defect to Enhance the Performance of FAPbI3 Perovskite Solar Cells by Ionic Liquid

Ionic liquids have been widely used to improve the efficiency and stability of perovskite solar cells (PSCs), and are generally believed to passivate defects on the grain boundaries of perovskites. However, few studies have focused on the relevant effects of ionic liquids on intragrain defects in perovskites which have been shown to be critical for the performance of PSCs. In this work, the effect of ionic liquid 1-hexyl-3-methylimidazolium iodide (HMII) on intragrain defects of formamidinium lead iodide (FAPbI3) perovskite is investigated. Abundant {111}c intragrain planar defects in pure FAPbI3 grains are found to be significantly reduced by the addition of the ionic liquid HMII, shown by using ultra-low-dose selected area electron diffraction. As a result, longer charge carrier lifetimes, higher photoluminescence quantum yield, better charge carrier transport properties, lower Urbach energy, and current-voltage hysteresis are achieved, and the champion power conversion efficiency of 24.09% is demonstrated. These observations suggest that ionic liquids significantly improve device performance resulting from the elimination of {111}c intragrain planar defects.

Ruddlesden-Popper Perovskite Nanocrystals as Interface Modification Layer for Efficient Perovskite Solar Cells

Perovskite nanocrystals are advantageous for interfacial passivation of perovskite solar cells (PSCs), but the insulating long alkyl chain surface ligands impede the charge transfer, while the conventional ligand exchange would possibly introduce surface defects to the nanocrystals. In this work, we reported novel in situ modification of CsPbBr3 nanocrystals using a short chain conjugated molecule 2-methoxyphenylethylammonium iodide (2-MeO-PEAI) for interfacial passivation of PSCs. Transmission electron microscopy studies with atomic resolution unveil the transformation from cubic CsPbBr3 to Ruddlesden-Popper phase (RPP) nanocrystals due to halogen exchange. Synergic passivation by the RPP nanocrystals and 2-MeO-PEA+ has led to suppressed interface defects and enhanced charge carrier transport. Consequently, PSCs with in situ modified RPP nanocrystals achieved a champion power conversion efficiency of 24.39%, along with an improvement in stability. This work brings insights into the microstructural evolution of perovskite nanocrystals, providing a novel and feasible approach for interfacial passivation of PSCs.

Color-tunable stable quasi-2D hybrid metal halide perovskites: synthesis, characterization, and optical analysis

Metal halide perovskites show remarkable optical properties and useful applications in optoelectronic devices. However, the instability of three-dimensional (3D) metal halide perovskites limits their applications, leading to the emergence of more stable two-dimensional (2D) metal halide perovskites. Herein, we present a facile synthesis of the 2D hybrid metal halide perovskite (EDA)(MA)n-1PbnBr3n+1 (EDA: ethylene diammonium, MA: methylammonium), where n = 1-6, and MAPbBr3 perovskite layers using an anti-solvent co-precipitation technique. The synthesized materials exhibited tunable optical properties, and the color emissions of pure EDAPbBr4 and (EDA)(MA)2Pb3Br10 perovskites were successfully tailored by altering halide anion layers. The band gap decreases as the value of n in the (EDA)(MA)n-1PbnBr3n+1 compound increases from 1 to 6. The as-prepared materials were characterized using X-ray diffraction (XRD) technique, Fourier transform infrared spectroscopy (FTIR), ultraviolet-visible spectroscopy (UV-Vis), photoluminescence spectroscopy (PL), scanning electron microscopy (SEM), and energy dispersive X-ray analysis (EDX). Finally, the stability of the 2D hybrid metal halide perovskite structures was evaluated under ambient conditions over different periods. Their tunable color emission was investigated and robust fluorescence was observed after 55 days. Thus, this study provides valuable insights into the synthesis and characterization of 2D hybrid metal halide perovskites for tunable color emission, highlighting their potential for use in various optoelectronic applications.