The Role of Electrostatic Repulsion on Increasing Surface Activity of Anionic Surfactants in the Presence of Hydrophilic Silica Nanoparticles

Surface modification of nanoparticles for enhanced applicability of nanofluids in harsh reservoir conditions: A comprehensive review for improved oil recovery

Nanoparticles improve traditional Enhanced Oil Recovery (EOR) methods but face instability issues. Surface modification resolves these, making it vital to understand its impact on EOR effectiveness. This paper examines how surface-modified nanoparticles can increase oil recovery rates. We discuss post-synthesis modifications like chemical functionalization, surfactant and polymer coatings, surface etching, and oxidation, and during-synthesis modifications like core-shell formation, in-situ ligand exchange, and surface passivation. Oil displacement studies show surface-engineered nanoparticles outperform conventional EOR methods. Coatings or functionalizations alter nanoparticle size by 1-5 nm, ensuring colloidal stability for 7 to 30 days at 25 to 65 °C and 30,000 to 150,000 ppm NaCl. This stability ensures uniform distribution and enhanced penetration through low-permeability (1-10 md) rocks, improving oil recovery by 5 to 50 %. Enhanced recovery is achieved through 1-25 μm oil-in-water emulsions, increased viscosity by ≥30 %, wettability changes from 170° to <10°, and interfacial tension reductions of up to 95 %. Surface oxidation is suitable for carbon-based nanoparticles in high-permeability (≥500 md) reservoirs, leading to 80 % oil recovery in micromodel studies. Surface etching is efficient for all nanoparticle types, and combining it with chemical functionalization enhances resistance to harsh conditions (≥40,000 ppm salinity and ≥ 50 °C). Modifying nanoparticle surfaces with a silane coupling agent before using polymers and surfactants improves EOR parameters and reduces polymer thermal degradation (e.g., only 10 % viscosity decrease after 90 days). Economically, 500 ppm of nanoparticles requires 56.25 kg in a 112,500 m3 reservoir, averaging $200/kg, and 2000 ppm of surface modifiers require 4 kg at $3.39/kg. This results in 188,694.30 barrels, or $16,039,015.50 at $85 per barrel for a 20 % increase in oil recovery. The economic benefits justify the initial costs, highlighting the importance of cost-effective nanoparticles for EOR applications.

Aggregation behavior of newly synthesized Gemini cationic surfactants in absence and in presence of different inorganic salts in 15% DMSO-water solvent

In this study, three Gemini cationic surfactants related to thiazol-2-amine with three hydrocarbon chain lengths including 3-hexylthiazol-3-ium (TAC6), 3-dodecylthiazol-3-ium (TAC12) and octadecylthiazol3-ium (TAC18) were prepared. Surfactant structures were confirmed with IR and 1HNMR Spectroscopies. Critical micelle concentrations for all surfactants in 15% DMSO-Water solvent were measured using conductometric, refractometric, and densitometric techniques. Thermodynamics parameters were computed and explained. Also, enhancing properties of all surfactants were indicated under the effect of two concentrations, 0.001 M and 0.01 M, of six inorganic salts including Cl-, Br-, I-, Co+2, Cu+2, and Mn+2 radicals using conductivity and refractive index measurements. All techniques used to measure critical micelles concentration showed a good convergence in measuring CMC values and the behavior of all surfactants in 15% DMSO-water solvent. Increasing the binding constant of the counter ion and association constant reflects the effect of hydrocarbon chain length increment on enhancing micelle formation, where TAC 18 was shown as the lowest CMC in all applied measurements. Modeling the density of all surfactant solutions under study indicates an increase in hydrophobic polarizability with an increase in the molecular weight of the surfactant. Inorganic salts decreased the CMC of all surfactants with the increase in Gibbs free energy of micellization which ensures easier formation of more stable micelles in the presence of a salt solution. The effect of salts on decreasing CMC for all surfactants under study was arranged in the following order: Mn+2 < Cu+2 < Co+2 for cationic radicals and I- < Br- < Cl- for anionic radicals.

Association in Like-Charged Surfactant-Nanoparticle Systems: Interfacial and Bulk Effects

The association of similarly charged surfactant molecules and nanoparticles in an aqueous solution remains unresolved, and the understandings reported in the literature are conflicting. To address this issue, we undertake a fundamental study to investigate bulk and interfacial phenomena in binary mixtures of (i) positively charged nanoparticles and cationic surfactants and (ii) negatively charged nanoparticles and anionic surfactants. We find that the surfactant molecules adsorb on the surface of the nanoparticle despite similar charge, leading to supercharging of particles and simultaneously driving more surfactant molecules to the air-dispersion interface. Hence, the properties of the dispersed species, such as the size and zeta potential, and the interfacial properties, such as the surface tension and surface excess concentration, change significantly. This effect is more pronounced at a low surfactant concentration and is observed irrespective of the size of nanoparticles and surfactant-particle combination. Further, we elucidate the important role of electrostatic interactions in the surfactant-particle complexation process by varying the pH of the dispersions. Contrary to changes in the properties of the dispersed species and interface, the presence of particles does not appreciably change the bulk property, such as the critical micelle concentration.

Effect of alkyl glucoside concentration on functional group structure and adsorption characteristics of anthracite

CONTEXT

To investigate the influence of different concentrations of surfactants on the adsorption of anthracite, the nonionic surfactant alkyl polyglucoside (APG) was selected. The study examined the adsorption characteristics of different concentrations of APG on the surface of anthracite. The results revealed the existence of two modes of APG adsorption on anthracite. Under the action of 0.06 wt% APG, APG was found to adsorb in a monolayer state on the anthracite surface, with a saturation adsorption capacity of 20.06 mg/g. When the solution concentration exceeded 0.14 wt%, APG exhibited a double-layer saturation adsorption state on anthracite, with a saturation adsorption capacity of 71.71 mg/g. Molecular dynamics simulations complemented these findings, demonstrating that low concentrations of APG could reduce the mobility of water molecules and enhance the hydrophilicity of anthracite. With an increase in the number of APG molecules, multi-layer adsorption occurred on the anthracite surface, making it more hydrophobic. Therefore, the differences in wettability of anthracite induced by different concentrations of APG were primarily attributed to the spatial distribution of the surfactant at the water/coal interface.

METHODS

This study analyzed the adsorption capacity of the surfactant through adsorption experiments and Fourier-transform infrared spectroscopy (FTIR) experiments. Molecular dynamics simulations were conducted to construct six concentration levels of water/APG/anthracite systems. Various aspects, including APG adsorption configurations, interaction energies, relative concentrations of each component, and the diffusion coefficient of water molecules, were discussed to elucidate the reasons for the differential wettability of anthracite induced by different concentrations of APG.

Recent advances in nanomaterial-stabilized pickering foam: Mechanism, classification, properties, and applications

Pickering foam is a type of foam stabilized by solid particles known as Pickering stabilizers. These solid stabilizers adsorb at the liquid-gas interface, providing superior stability to the foam. Because of its high stability, controllability, versatility, and minimal environmental impact, nanomaterial-stabilized Pickering foam has opened up new possibilities and development prospects for foam applications. This review provides an overview of the current state of development of Pickering foam stabilized by a wide range of nanomaterials, including cellulose nanomaterials, chitin nanomaterials, silica nanoparticles, protein nanoparticles, clay mineral, carbon nanotubes, calcium carbonate nanoparticles, MXene, and graphene oxide nanosheets. Particularly, the preparation and surface modification methods of various nanoparticles, the fundamental properties of nanomaterial-stabilized Pickering foam, and the synergistic effects between nanoparticles and surfactants, functional polymers, and other additives are systematically introduced. In addition, the latest progress in the application of nanomaterial-stabilized Pickering foam in the oil industry, food industry, porous functional material, and foam flotation field is highlighted. Finally, the future prospects of nanomaterial-stabilized Pickering foam in different fields, along with directions for further research and development directions, are outlined.

Numerical study of the mechanisms of nano-assisted foam flooding in porous media as an alternative to gas flooding

Oil reservoirs are nearing maturation, necessitating novel enhanced oil recovery (EOR) techniques to meet escalating global energy demands. This demand has spurred interest in reservoir production analysis and forecasting tools to enhance economic and technical efficiency. Accurate validation of these tools, known as simulators, using laboratory or field data is pivotal for precise reservoir productivity estimation. This study delves into the application of nanoparticles in foam flooding for mobility control to improve sweep efficiency. Foam generation can occur in-situ by simultaneous injection of surfactants and gas or through pre-generated foam injection into the reservoir. In this work, a series of systematic simulations were run to investigate how much injected fluids can reduce gas breakthrough while also increasing oil recovery. Subsequently, we analyzed the most effective optimization strategies, considering their economic limits. Our primary objective is to numerically model nanofoam flooding as an innovative EOR approach, synergizing foam flooding mechanisms with nanotechnology benefits. In this work, modeling of nanoparticles in foam liquid was represented by the interfacial properties provided to the injection fluid. Additionally, we simulated Water-Alternating-Gas (WAG) injection schemes across various cycles, comparing their outcomes. Our results showed that nanofoam injection achieved a higher recovery factor of at least 38% and 95% more than WAG and gas injections, respectively. The superior efficiency and productivity of foam injection compared to WAG and gas injection suggest an optimal EOR approach within the scope of our model. These simulated optimization techniques contribute to the future development of processes in this field.

Evaluation of Interfacial Structure of Self-Assembled Nanoparticle Layers: Use of Standard Deviation between Calculated and Experimental Drop Profiles as a Novel Method

The self-assembly of nanoparticles (NPs) at interfaces is currently a topic of increasing interest due to numerous applications in food technology, pharmaceuticals, cosmetology, and oil recovery. It is possible to create tunable interfacial structures with desired characteristics using tailored nanoparticles that can be precisely controlled with respect to shape, size, and surface chemistry. To address these functionalities, it is essential to develop techniques to study the properties of the underlying structure. In this work, we propose an experimental approach utilizing the standard deviation of drop profiles calculated by the Laplace equation from experimental drop profiles (STD), as an alternative to the Langmuir trough or precise microscopic methods, to detect the initiation of closely packed conditions and the collapse of the adsorbed layers of CTAB-nanosilica complexes. The experiments consist of dynamic surface/interfacial tension measurements using drop profile analysis tensiometry (PAT) and large-amplitude drop surface area compression/expansion cycles. The results demonstrate significant changes in STD values at the onset of the closely packed state of nanoparticle-surfactant complexes and the monolayer collapse. The STD trend was explained in detail and shown to be a powerful tool for analyzing the adsorption and interfacial structuring of nanoparticles. Different collapse mechanisms were reported for NP monolayers at the liquid/liquid and air/liquid interfaces. We show that the interfacial tension (IFT) is solely dependent on the extent of interfacial coverage by nanoparticles, while the surfactants regulate only the hydrophobicity of the self-assembled complexes. Also, the irreversible adsorption of nanoparticles and the increasing number of adsorbed complexes after the collapse were observed by performing consecutive drop surface compression/expansion cycles. In addition to a qualitative characterization of adsorption layers, the potential of a quantitative calculation of the parameter STD such as the number of adsorbed nanoparticles at the interface and the distance between them at different states of the interfacial layer was discussed.

Charge controlled interactions between DNA-modified silica nanoparticles and fluorosurfactants in microfluidic water-in-oil droplets

Microfluidic droplets are an important tool for studying and mimicking biological systems, e.g., to examine with high throughput the interaction of biomolecular components and the functionality of natural cells, or to develop basic principles for the engineering of artificial cells. Of particular importance is the approach to generate a biomimetic membrane by supramolecular self-assembly of nanoparticle components dissolved in the aqueous phase of the droplets at the inner water/oil interface, which can serve both to mechanically reinforce the droplets and as an interaction surface for cells and other components. While this interfacial assembly driven by electrostatic interaction of surfactants is quite well developed for water/mineral oil (W/MO) systems, no approaches have yet been described to exploit this principle for water/fluorocarbon oil (W/FO) emulsion droplets. Since W/FO systems exhibit not only better compartmentalization but also gas solubility properties, which is particularly crucial for live cell encapsulation and cultivation, we report here the investigation of charged fluorosurfactants for the self-assembly of DNA-modified silica nanoparticles (SiNP-DNA) at the interface of microfluidic W/FO emulsions. To this end, an efficient multicomponent Ugi reaction was used to synthesize the novel fluorosurfactant M4SURF to study the segregation and accumulation of negatively charged SiNP-DNA at the inner interface of microfluidic droplets. Comparative measurements were performed with the negatively charged fluorosurfactant KRYTOX, which can also induce SiNP-DNA segregation in the presence of cations. The segregation dynamics is characterized and preliminary results of cell encapsulation in the SiNP-DNA functionalized droplets are shown.

Static and dynamic adsorption of a gemini surfactant on a carbonate rock in the presence of low salinity water

In chemical enhanced oil recovery (cEOR) techniques, surfactants are extensively used for enhancing oil recovery by reducing interfacial tension and/or modifying wettability. However, the effectiveness and economic feasibility of the cEOR process are compromised due to the adsorption of surfactants on rock surfaces. Therefore, surfactant adsorption must be reduced to make the cEOR process efficient and economical. Herein, the synergic application of low salinity water and a cationic gemini surfactant was investigated in a carbonate rock. Firstly, the interfacial tension (IFT) of the oil-brine interface with surfactant at various temperatures was measured. Subsequently, the rock wettability was determined under high-pressure and high-temperature conditions. Finally, the study examined the impact of low salinity water on the adsorption of the cationic gemini surfactant, both statically and dynamically. The results showed that the low salinity water condition does not cause a significant impact on the IFT reduction and wettability alteration as compared to the high salinity water conditions. However, the low salinity water condition reduced the surfactant's static adsorption on the carbonate core by four folds as compared to seawater. The core flood results showed a significantly lower amount of dynamic adsorption (0.11 mg/g-rock) using low salinity water conditions. Employing such a method aids industrialists and researchers in developing a cost-effective and efficient cEOR process.

Conformal Conductive Features on Curvilinear Surfaces with Self-Assembled Silver Nanoplate Thin Films

In this study, a water transfer method was developed to fabricate conducive thin-film patterns on 3D curvilinear surfaces. Crystalline silver nanoplates (AgNPLs) with a dimension of 700 nm and a thickness of 35 nm were suspended in ethanol with an anionic surfactant, sodium dodecyl sulfate, to improve the suspension stability. The prepared AgNPL suspension was then spread over the water surface via the Langmuir-Blodgett approach to generate a self-assembled thin film. By dipping an accepting object with a robotic arm, the floating AgNPL thin film with nanometer thickness can be effectively transferred to the object surfaces and exhibited a superior conductivity up to 15% of bulk silver without thermal sintering. Besides good conductivity, the AgNPL conductive thin films can also be transferred efficiently on any curvilinear (concave and convex) surface. Moreover, with the help of masks, conductive patterns can be produced on water surfaces and transferred to curvilinear surfaces for electronic applications. As a proof of concept, several examples were demonstrated to display the capability of this approach for radiofrequency identification and other printed circuit applications.

Environmental impact assessment of nanofluids containing mixtures of surfactants and silica nanoparticles

Due to widespread use of nanoparticles in surfactant-based formulations, their release into the environment and wastewater is unavoidable and toxic for biota and/or wastewater treatment processes. Because of concerns over the environmental impacts of nanofluids, studies of the fate and environmental impacts, hazards, and toxicities of nanoparticles are beginning. However, interactions between nanoparticles and surfactants and the biodegradability of these mixtures have been little studied until now. In this work, the environmental impacts of nanofluids containing mixtures of surfactants and silica nanoparticles were valuated. The systems studied were hydrophilic silica nanoparticles (sizes 7 and 12 nm), a nonionic surfactant (alkyl polyglucoside), an anionic surfactant (ether carboxylic acid), and mixtures of them. The ultimate aerobic biodegradation and the interfacial and adsorption properties of surfactants, nanoparticles, and mixtures during biodegradation were also evaluated. Ultimate biodegradation was studied below and above the CMCs of the individual surfactants. The interfacial and adsorption properties of surfactant solutions containing nanoparticles were influenced by the addition of silica particles. It was determined that silica nanoparticles reduced the capability of the nonionic surfactant alkyl polyglucoside to decrease the surface tension. Thus, silica NPs promoted a considerable increase in the surfactant CMC, whereas the effect was opposite in the case of the anionic surfactant ether carboxylic acid. Increasing concentrations of surfactant and nanoparticles in the test medium caused decreases in the maximum levels of mineralization reached for both types of surfactants. The presence of silica nanoparticles in the medium reduced the biodegradability of binary mixtures containing nonionic and anionic surfactants, and this effect was more pronounced for larger nanoparticles. These results could be useful in modelling the behaviour of nanofluids in aquatic environments and in selecting appropriate nanofluids containing nanoparticles and surfactants with low environmental impact.

Superhydrophilic and Underwater Superoleophobic Cotton Fabric for Oil-Water Separation and Removal of Heavy-Metal Ion

Superhydrophilic and underwater superoleophobic cotton fabric (named CS-CF-PDA, or m-CF) was prepared by modifying the cotton fabric (CF) with dopamine (DA) and chitosan (CS). The oil-water separation and heavy-metal ion (e.g., Cu(II)) adsorption performances of m-CF were investigated, and m-CF was characterized by field emission scanning electron microscopy (FE-SEM), energy-dispersive spectroscopy (EDS), Fourier transform infrared (FT-IR), and thermogravimetric analysis (TGA). The results showed that the underwater oil contact angle (UWOCA) of m-CF was more than 156°. The m-CF was used to treat artificial oily wastewater containing Cu(II) under room temperature and atmospheric pressure and gravity, by which the separation efficiency, water flux, and Cu(II) removal rate could reach 99%, 17 400 L·m^-2·h^-1, and 89%, respectively. Additionally, in the process of continuous treatment of oily wastewater, the water flux slightly decreased; on the contrary, the Cu(II) removal rate decreased significantly to 67% within 120 s. Cu(II) was one of the reasons for the decrease of water flux. The m-CF of adsorbed Cu(II) could be leached with HCl (0.1 mol·L^-1) solution, and the Cu(II) desorption rate could reach over 95% within 120 s. After strong acid, strong alkali, high salt, and abrasion treatment, the UWOCAs of m-CF were still higher than 150°. In a word, in terms of oil-water separation, m-CF exhibited good acid, alkali, salt, and abrasion resistances. Also, it is an underwater superoleophobic material involving simple preparation, low cost, and environmental friendliness, which could remove the floating oil and heavy-metal ions from wastewater and has good industrial application prospects.

Exploring the Effect of Glycerol and Hydrochloric Acid on Mesoporous Silica Synthesis: Application in Insulin Loading

Mesoporous silica (MPS), a carrier for active pharmaceutical ingredients, has a wide range of particle and pore morphology. A thorough understanding of ingredients used in MPS synthesis is an important prerequisite for optimizing its physicochemical characteristics. The present study aimed to evaluate the effect of glycerol and hydrochloric acid on the characteristics of synthesized MPS. Ordered MPS materials were synthesized using the pluronic P123 template and tetraethyl orthosilicate (TEOS) precursor. A three-level factorial design was employed to study the interaction between glycerol and hydrochloric acid. The optimized MPS particles were reasonably uniform in shape (short and rod-shaped) and < 1 μm in size with a smooth surface morphology. The nitrogen adsorption-desorption analysis revealed that the uniform cylindrical pores of the prepared MPS had a diameter > 5 nm and a total surface area > 500 m²/g. With increasing acid and glycerol concentrations, the particle size of MPS decreased. However, while the glycerol increased the heterogeneity of the synthesized particles, the acid decreased it. The developed MPS was successfully loaded with a biological drug (insulin) with a 21.94% encapsulation efficiency. The MPS prepared in this study exhibits potential applications as a drug delivery carrier for drugs with a large molecular weight.

Contamination in Sodium Dodecyl Sulfate Solutions: Insights from the Measurements of Surface Tension and Surface Rheology

The presence of contamination in sodium dodecyl sulfate (SDS) solutions in the form of dodecanol (LOH) is known to drastically affect the resulting interfacial properties such as surface tension (SFT) and rheology. Dodecanol molecules, which are the product of SDS hydrolysis and are inherently present in SDS solutions, have higher surface activity compared to SDS because they are less soluble in water. A characteristic dip in the SFT isotherm is an indicator of the dodecanol contamination in the sample. The presence of an electrolyte in the solution impacts the surface activity of SDS and its critical micelle concentration, and could yield SFT isotherms that closely match those obtained for pure SDS samples. The interpretation of the isotherms in such cases could thus lead to misinterpretation of the surface purity. In this work, we have examined the SFT isotherms for SDS solutions in both the absence and presence of electrolyte. We have fitted the isotherms to three different thermodynamic adsorption models to estimate the amount of dodecanol present in the sample. We have applied the estimated values for the LOH content in a two-component rheological model to predict the viscoelasticity of such surfactant-laden surfaces. We have compared these results with the experimentally measured interfacial rheological properties. Our findings demonstrate that the presence of impurities can be captured under dynamic expansion and contractions, even for solutions containing background electrolyte.

Elastic gas/water interface for highly stable foams with modified anionic silica nanoparticles and a like-charged surfactant

HYPOTHESIS

Surface active anionic nanoparticles (NPs) with strategically designed covalent ligands may be combined with a liked-charged surfactant to form a highly elastic gas-water interface leading to highly stable gas/water foams.

EXPERIMENTS

The colloidal stability of the NPs was determined by dynamic light scattering, and the surface elastic dilational modulus E' of the interface by sinusoidal oscillation of a pendant droplet at 0.1 Hz, which was superimposed on large-amplitude compression-expansion cycles. The foam stability was measured with optical microscopy of the bubble size distribution and from the macroscopic foam height.

FINDINGS

The NPs played the key role the formation of a highly elastic air-water interface with a high E' despite a surfactant level well above the critical micelle concentration. Unlike the case for most previous studies, the NP amphiphilicity was essentially independent of the surfactant given the very low adsorption of the surfactant on the like-charged NP surfaces. With high E' values, both coalescence and coarsening were reduced leading to highly foam up to 80 °C. However, the surfactant facilitated foam generation at much lower shear rates than with NPs alone. The tuning of NP surfaces with ligands for colloidal stability in brine and simultaneously high amphiphilicity at the gas-water interface, over a wide range in surfactant concentration, is of broad interest for enabling the design of highly stable foams.

Preparation and performance of a biological dust suppressant based on the synergistic effect of enzyme-induced carbonate precipitation and surfactant

To control the dust pollution caused by open-pit coal mining and reduce or avoid the secondary hazards of existing dust suppressants to the environment, a biological dust suppressant was prepared through the synergistic effect of a surfactant and an enzyme-induced carbonate precipitation. The optimal ratio of biological dust suppressant was determined, and the dust suppressive effect and dust consolidation mechanism of the biological dust suppressant were investigated. The results showed that the optimal biological dust suppressant had an alkyl polyglycoside (APG) concentration of 0.3 wt.%, a urea-CaCl₂ concentration of 0.6 mol/L, and a urease to urea-CaCl₂ volume ratio of 1:3. The wind erosion resistance of coal dust treated with this dust suppressant was enhanced by 86.69%. The adsorption of the biological dust suppressant by coal dust was mainly due to the electrostatic interaction between the surfactant and coal dust. The mineralization product of the dust suppressant was calcite-type CaCO₃, which consolidated coal dust due to the formation of intermolecular hydrogen bonds between CaCO₃ and coal dust.

Playing Favorites: Preferential Adsorption of Nonionic over Anionic Surfactants at the Liquid/Liquid Interface

While many studies have investigated synergic interactions between surfactants in mixed systems, understanding possible competitive behaviors between interfacial components of binary surfactant systems is necessary for the optimized efficacy of applications dependent on surface properties. Such is the focus of these studies in which the surface behavior of a binary surfactant mixture containing nonionic (Span-80) and anionic (AOT) components adsorbing to the oil/water interface was investigated with vibrational sum-frequency (VSF) spectroscopy and surface tensiometry experimental methods. Time-dependent spectroscopic studies reveal that while both nonionic and anionic surfactants initially adsorb to the interface, anionic surfactants desorb over time as the nonionic surfactant continues to adsorb. Concentration studies that vary the ratio of Span-80 to AOT in bulk solution show that the nonionic surfactant preferentially adsorbs to the oil/water interface over the anionic surfactant. These studies have important implications for applications in which mixed surfactant systems are used to alter interfacial properties, such as pharmaceuticals, industrial films, and environmental remediation.

Wettability Changes Due to Nanomaterials and Alkali-A Proposed Formulation for EOR

We investigated the usage of two silica nanomaterials (surface-modified) and alkali in enhanced oil recovery through Amott spontaneous imbibition tests, interfacial tension (IFT) measurements, and phase behavior. We evaluated the wettability alteration induced by the synergy between nanomaterials and alkali. Moreover, numerical analysis of the results was carried out using inverse Bond number and capillary diffusion coefficient. Evaluations included the use of Berea and Keuper outcrop material, crude oil with different total acid numbers (TAN), and Na2CO3 as alkaline agent. Data showed that nanomaterials can reduce the IFT, with surface charge playing an important role in this process. In synergy with alkali, the use of nanomaterials led to low-stable IFT values. This effect was also seen in the phase behavior tests, where brine/oil systems with lower IFT exhibited better emulsification. Nanomaterials' contribution to the phase behavior was mainly the stabilization of the emulsion middle phase. The influence of TAN number on the IFT and phase behavior was prominent especially when combined with alkali. Amott spontaneous imbibition resulted in additional oil recovery ranging from 4% to 50% above the baseline, which was confirmed by inverse Bond number analysis. High recoveries were achieved using alkali and nanomaterials; these values were attributed to wettability alteration that accelerated the imbibition kinetics as seen in capillary diffusion coefficient analysis.

Prediction of surface tension of solution in the presence of hydrophilic silica nanoparticle and anionic surfactant by ATR-FTIR spectroscopy and chemometric methods

In the current research, an analytical method was proposed for the quantitative determination of surface tension of anionic surfactant solutions in the presence of hydrophilic silica nanoparticles using attenuated total reflection Fourier-transform infrared (ATR-FTIR) spectroscopy and chemometric methods. The surface tension behavior of anionic surfactant solutions considerably changes by the addition of silica nanoparticles with different particle size. The spectral data of solutions were used for prediction of surface tension using two calibration methods based on support vector machine regression (SVM-R) as a non-linear algorithm and partial least squares regression (PLS-R) as a linear algorithm. For preprocessing of data, baseline correction and standard normal variate (SNV) were also applied. Root mean square error of prediction (RMSEP) in SVM-R and PLS-R methods were 4.203 and 4.507, respectively. Considering the complexity of the samples, the SVM-R model was found to be reliable. The proposed method is fast and easy for measurement of the surface tension of surfactant solutions without any sample preparation step in chemical enhanced oil recovery (C-EOR).

Synergistic and Competitive Adsorption of Hydrophilic Nanoparticles and Oil-Soluble Surfactants at the Oil-Water Interface

Fundamental insights into the interplay and self-assembly of nanoparticles and surface-active agents at the liquid-liquid interface play a pivotal role in understanding the ubiquitous colloidal systems present in our natural surroundings, including foods and aquatic life, and in the industry for emulsion stabilization, drug delivery, or enhanced oil recovery. Moreover, well-controlled model systems for mixed interfacial adsorption of nanoparticles and surfactants allow unprecedented insights into nonideal or contaminated particle-stabilized emulsions. Here, we investigate such a model system composed of hydrophilic, negatively, and positively charged silica nanoparticles and the oil-soluble cationic lipid octadecyl amine with in situ synchrotron-based X-ray reflectometry, which is analyzed and discussed jointly with dynamic interfacial tensiometry. Our results indicate that negatively charged silica nanoparticles only adsorb if the oil-water interface is covered with the positively charged lipid, indicating synergistic adsorption. Conversely, the positively charged nanoparticles readily adsorb on their own, but compete with octadecyl amine and reversibly desorb with increasing concentrations of the lipid. These results further indicate that with competitive adsorption, an electrostatic exclusion zone exists around the adsorbed particles. This prevents the adsorption of lipid molecules in this area, leading to a decreased surface excess concentration of surfactants and unexpectedly high interfacial tension.

Stabilizing decontamination foam using surface-modified silica nanoparticles containing chemical reagent: foam stability, structures, and dispersion properties

The stabilization of decontamination foams containing a chemical reagent is a crucial requirement for their use in the decontamination of nuclear power plants. We have investigated the effects on decontamination foam stability of adding silica nanoparticles (NPs) modified with various functional groups, namely propyl (–CH₃), amine (–NH₂), and thiol (–SH) groups. The surface properties of these silica NPs were characterized with ATR-FTIR, solid NMR, and TGA analyses. We also established that the agglomeration in such foams of the amine-modified silica NPs is weaker than that of the other modified silica NPs due to their thorough dispersion in the liquid film. Further, the foam containing amine-modified silica NPs was found to be stable for 60 min at a pH of 2, i.e. under decontamination conditions. The bubble structure analysis showed that this decontamination foam has a bubble count that is approximately 5–8 times higher than the foams containing NPs modified with the other functional groups, which indicates that the decontamination foam with amine-modified silica NPs has the best foam structure of the three investigated foams. The well-dispersed and smaller amine-modified silica NPs enhance the foam stability by providing a barrier between the gas bubbles and delaying their coalescence. In contrast, the thiol- and propyl-modified silica NPs form aggregates with large diameters that reduce the maximum capillary pressure of coalescence and hence decrease the foam stability.

The stabilization of decontamination foams containing a chemical reagent is a crucial requirement for their use in the decontamination of nuclear power plants.

Transition between a Pickering Emulsion and an Oil-in-Dispersion Emulsion Costabilized by Alumina Nanoparticles and a Cationic Surfactant

The transition between a novel oil-in-dispersion emulsion and an oil-in-water (O/W) Pickering emulsion triggered by pH was achieved using alumina nanoparticles in combination with a cationic surfactant. In acidic and neutral aqueous media, positively charged particles and the surfactant both at very low concentrations costabilize an oil-in-dispersion emulsion with the surfactant adsorbed at droplet interfaces and particles dispersed in the aqueous phase between the droplets. In alkaline media, however, particles become negatively charged and are hydrophobized in situ by adsorption of the surfactant to become surface-active and stabilize an O/W Pickering emulsion. The transition between the two is also possible by lowering the pH. The transformation can be achieved several times in a mixture of 0.1 wt % nanoparticles and 0.01 mM surfactant. This transition is significant, since particles can be made to either adsorb at the oil-water interface, which is beneficial for applications like biphasic catalysis, or remain dispersed in the aqueous phase, which is favorable for their recovery and reuse.

Solution properties and comparative antimicrobial efficacy study of different brands of toothpaste of Nepal

Background

The main objective of this study is to compare the effectiveness of toothpaste formulations in giving total protection to the oral cavity. So, three important solution properties: surface tension, conductivity, and pH measurements, have been investigated for eight kinds of commercial herbal and non-herbal based toothpaste of Nepal. The study was extended to evaluate the antibacterial efficacy of toothpaste formulations against the Gram-positive bacteria Staphylococcus aureus (S. aureus) and Gram-negative bacteria Escherichia coli (E. coli), and this was done by standard agar well diffusion technique. Amikacin (30 μg/disk) was used as a positive control to compare the antibacterial potency of the investigated toothpaste.

Results

The surface tension of all toothpaste formulations increased with the decrease in concentration. However, the conductivity of the formulations decreased with the decrease in concentration. The highest pH of 8.24 was recorded for Dabur Super Salt (DSS) and all values were found to be higher in tap water solutions. All toothpaste formulations showed significant growth inhibition against both S. aureus and E. coli. The overall antibacterial sensitivity of Dabur Red (DR) is higher for S. aureus. The solid material content was found to be highest for Dabur Herbal Gel (DHG) and lowest for Pepsodent (PD).

Conclusion

The findings of the present study showed all toothpaste formulations as effective in inhibiting the growth of tested bacterial species. Toothpaste formulations were found slightly alkaline, which favors bacterial growth inhibition. Increasing surface tension and decreasing conductivity value of toothpaste relative to a decrease in concentration favor its desirable cleansing action.

A flow velocity dependence of dynamic surface tension in Plateau borders of foam

HYPOTHESIS

Liquid drainage through foams is a multiscale process, that primarily occurs through channels known as Plateau borders (PBs). Recent experimental studies of isolated PBs have observed variations in channel surface tension, γ, with liquid flow rate, Q, for systems containing soluble low molecular weight surfactant (LMWS). The current study proposes that the dynamic surface tension (DST) could be responsible for this effect, where the residence time of surfactant molecules in the PB is similar to the time required for their adsorption to the channel interface.

EXPERIMENTS

Profile geometries of isolated 'ideal' PB's were created in a bespoke experimental setup at controlled forced liquid flow rates. Average surfactant residence times, τ_Res, were calculated for solutions of Sodium dodecylsulfate (SDS), Tween 20 (T20) and Tween 80 (T80), and used to calculate corresponding average DST values in discrete regions of measured PB profiles. DST values were combined with microscale drainage theory to assess the potential physical implications on liquid flow.

FINDINGS

Significant variations in the magnitude of γ were calculated based on surfactant characteristics, where only the rapid adsorption of SDS was sufficient to produce DST values approaching equilibrium. These findings seriously question assumptions of near equilibrium surface tension in LMWS foam systems above their critical micelle concentration (CMC). Furthermore, the presence of surface tension gradients identified using this discrete approach, highlights the need to further refine the current theory to a continuous approach incorporating Marangoni effects.

Evaluation of silica nanoparticle mediated delivery of protease inhibitor in tomato plants and its effect on insect pest Helicoverpa armigera

The inert and surface tunable nature of silica nanoparticles (SiNPs) makes them suitable for different applications. We have evaluated the potential of SiNPs for delivering proteins in tomato (Lycopersicon esculentum) plants. SiNPs of 20 and 100 nm (Si20 and Si100) were functionalized with (3-aminopropyl) triethoxysilane (APTES) to obtain Si20APT and Si100APT, respectively, that were non-toxic toward plants. The functionalized nanoparticles were taken up by plants through roots as well as leaf surfaces. They were seen to be localized near the vasculature, particularly around the xylem. Si20APT and Si100APT nanoparticles were conjugated with soybean trypsin inhibitor (STI) to yield Si20APT-STI and Si100APT-STI, respectively. Based on the trypsin inhibitory activity of loaded nanoparticles, optimum loading was obtained for 0.4 mg of STI per 0.8 mg of NPs. Si20APT nanoparticles retained higher contents of STI than Si100APT. Exposure of STI-conjugated nanoparticles to 25°C or pH 8.0 aided release of the inhibitor. The particle bound STI inhibited bovine trypsin by 80% and Helicoverpa armigera gut proteinase (HGP) activity by 50%. Second instar H. armigera larvae ingesting STI-loaded particles (incorporated in artificial diet or leaves) showed significant retardation in growth. In choice assays, Si20APT-STI applied leaf discs were strikingly avoided by insect larvae. On the basis of the results obtained in this investigation, we recommend the use of Si20 nanoparticles for developing plant delivery vehicles in the future.

Effect of the Surfactant Charge and Concentration on the Change in the Forces between Two Charged Surfaces in Surfactant Solutions by a Liquid Flow

A combined atomic force microscope (AFM)-peristaltic pump system was used to determine the effect of a flow on the forces between two negatively charged surfaces (silica particle and silicon wafer) in aqueous solutions containing surfactants. The effect of the surfactant charge on the forces was determined by using an anionic surfactant (sodium dodecyl sulfate, SDS) and a cationic surfactant (dodecyltrimethylammonium bromide, DTAB) of the same chain length. The surfactant concentration effect was determined by using concentrations up to the critical micelle concentration. In the case of SDS, a flow reduced the range and magnitude of the repulsive forces. The force range reduction was explained by a shrinking of the diffuse layers, due to the deformation of the diffuse layer by the flow. The force magnitude reduction was explained by (1) the increased electrostatic screening due to the thinner diffuse layers and (2) an increased adsorption of specific ions, such as Na⁺, to the silica surfaces. In the case of DTAB, a concentration (8.0 mM) that gave an attractive force in the absence of a flow gave a repulsive force in the presence of a flow. Comparison of AFM images of a silicon wafer in DTAB measured in the absence and presence of a liquid flow showed that the number of DTAB patches adsorbed to the silicon wafer increased with a liquid flow. The change in the forces with a flow was therefore explained by this change in the DTAB adsorption to the negatively charged surfaces. As a liquid flow can change the charge of a surface, it may be possible to control the aggregation/dispersion of charged particles via the flow rate, if the appropriate surfactant type and concentration are used.

Combination of Rhamnolipid and Chitosan in Nanoparticles Boosts Their Antimicrobial Efficacy

Nanomaterials have emerged as antimicrobial agents due to their unique physical and chemical properties. The development of nanoparticles (NPs) composed of natural biopolymers and biosurfactants have sparked interest, as they can be obtained without the use of complex chemical synthesis and toxic materials. In this study, we develop antimicrobial nanoparticles combining the biopolymer chitosan with the biosurfactant rhamnolipid. Addition of rhamnolipid reduced the size and polydispersity index of chitosan nanoparticles showing a more positive surface charge with improved stability, suggesting that chitosan-free amino groups are predominantly present on the surface of nanoparticles. Antimicrobial activity of chitosan/rhamnolipid nanoparticles (C/RL-NPs) against Staphylococcus strains surpassed that of either single rhamnolipid or chitosan, both in planktonic bacteria and biofilms. Minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) of C/RL-NPs were determined considering the concentration of each individual molecule in NPs. MIC values of 14/19 μg mL^-1 and MBC of 29/37 μg mL^-1 were observed for S. aureus DSM 1104 and MIC and MBC of 29/37 and 58/75 μg mL^-1 were observed against S. aureus ATCC 29213, respectively. For S. epidermidis, MIC and MBC of 7/9 and 14/19 μg mL^-1 were noticed. Chitosan and chitosan nanoparticles eliminate the bacteria present in the upper parts of biofilms, while C/RL-NPs were more effective, eradicating most sessile bacteria and reducing the number of viable cells below the detection limit, when NPs concentration of 58/75 μg mL^-1 was applied for both S. aureus DSM 1104 and S. epidermidis biofilms. The improved antibacterial efficacy of C/RL-NPs was linked to the increased local delivery of chitosan and rhamnolipid at the cell surface and, consequently, to their targets in Gram-positive bacteria. The combination of chitosan and rhamnolipid offers a promising strategy to the design of novel nanoparticles with low cytotoxicity, which can be exploited in pharmaceutical and food industries.

The influence of negatively charged silica nanoparticles on the surface properties of anionic surfactants: electrostatic repulsion or the effect of ionic strength?

The presence of negatively charged nanoparticles affects the surface activity of anionic surfactants in an aqueous phase. Recent studies suggest that electrostatic repulsive forces play an important role in increasing the surface activity of surfactants. However, the addition of nanoparticles also increases the ionic strength of the system, which has a significant impact on the surfactant's properties, e.g. its critical micelle concentration (CMC). To investigate how and to what extent electrostatic forces and ionic strength influence the behavior of ionic surfactants, the surface tension and elasticity of different solutions were measured using drop profile tensiometry as a function of the surfactant (SDBS), nanoparticle (silica) and salt (KNO₃) concentration. It is observed that the surface activity of the surfactants is mainly influenced by the change in the system's ionic strength due to the presence of nanoparticles. Several characteristic parameters including the equivalent concentration of the surfactant, the CMC and the apparent partial molar area of the adsorbed surfactant are theoretically calculated and further employed to validate experimental observations. Both the nanoparticles and electrolyte decrease the CMC, while the equivalent concentration of the surfactant remains nearly constant. This paper presents a criterion to estimate the possible influence of such forces for nanoparticles of different sizes and mass fractions.

Reversible Adsorption of Nanoparticles at Surfactant-Laden Liquid-Liquid Interfaces

In this study, we show that hydrophilic nanoparticles can readily desorb from liquid-liquid interfaces in the presence of surfactants that do not change the wettability of the particles. Our observations are based on a simple theoretical approach to assess the number of adsorbed particles at the surfactant-laden liquid-liquid interface. We test this approach by studying the interfacial self-assembly of equally charged particles and lipids dissolved in separate immiscible phases. Hence, we investigate the interfacial adsorption of aminated silica particles (80 nm) and octadecylamine to the decane/water interface by interfacial tension measurements, which are supplemented by interfacial rheology of the adsorbed interfacial films, scanning electron microscopy images of Langmuir-Blodgett films, and measurements of the three-phase contact angle of the particle surface in the presence of surfactants. The measurements show that particles adsorb at the surfactant-laden interface at all investigated surfactant concentrations and compete with the surfactants for interfacial coverage. Additionally, the wettability of the hydrophilic particles does not change in the presence of the lipids, except for the highest investigated lipid concentration. Comparing the adsorption energies of one particle and of the lipids as a function of the particle contact angle provides an estimate of the tendency for interfacial adsorption of particles from which the particle coverage can be assessed. Based on these findings, equally charged particles and lipids show a competitive behavior at the interface determined by the bulk surfactant concentration and the attachment energies of the particles at the interface. This leads to a simple mechanistic model demonstrating that particles can readily desorb from the interface due to direct displacement by surfactants, which are loosely adsorbed at the oil-facing particle side. This mechanism critically lowers the otherwise high interfacial energy barrier against particle desorption, which otherwise would lead to virtually irreversible particle attachment at the interface.

Influence of hydrophilic silica nanoparticles on the adsorption layer properties of non-ionic surfactants at water/heptane interface

There is a notable paucity of studies investigating the impact of charged nanoparticles on the interfacial behavior of nonionic surfactants, assuming that the interactions are negligible in the absence of electrostatic forces. Here, we argue about our observations and the existence of a complex interfacial behavior in such systems depending on the type and chemical structure of surfactant. This study set out to investigate the effects of interactions between hydrophilic silica nanoparticles (NP) and non-ionic surfactants on water/heptane dynamic interfacial properties using drop profile analysis tensiometry (PAT). Three surfactants were studied, namely Triton X-100 (significantly soluble in water phase), C₁₂DMPO (well soluble in both phases) and SPAN 80 (oil-soluble). The different chemical structures and partition coefficients of the surfactants enabled us to cover possible interactions and differentiate between bulk and interfacial interactions. We observed that hydrophilic silica NPs had a negligible effect on the interfacial behavior of Triton X-100, that they increased the surface activity of C₁₂DMPO when both compounds are initially in the aqueous phase. Most interestingly is that the added NPs generated unstable interfacial NP-surfactant complexes and reduced the pseudo-equilibrium interfacial tension of oil-soluble surfactant, Span 80, even though NPs and surfactants were in different bulk phases.