Indoor air formaldehyde (HCHO) pollution of urban coach cabins

Real-time evolution characteristics and potential reactions of contaminants in commuter bus cabin air

Despite the increasing use of motor vehicles, the impact of airborne pollutants and their health risks inside public transportation, such as commuter buses, is not well understood. This study assessed air quality inside an urban commuter bus by continuously monitoring PM10, PM2.5, and CO concentrations during both driving and parking periods. Our findings revealed that the ventilation system of the bus significantly reduced the infiltration of outdoor particulate matter and water vapor. However, CO concentrations were considerably higher inside the bus than outside, primarily due to vehicular self-emission. The ineffection of the ventilation system to remove CO potentially increases long-term exposure risks for passengers. The study identified ozone as a key oxidant in the cabin. Besides vehicle emissions, C3-C10 saturated aldehydes and carbonyl compounds were detected, including acetone, propanal, and hexanal. The presence of 6-MHO, an oxidation product of squalene, suggests that passengers contribute to VOCs load through direct emissions or skin surface reactions. Additionally, human respiration was found to significantly contribute to isoprene levels, estimated at 81.7 %. This research underscores the need for further investigation into the cumulative effects of stable compounds in cabin air and provides insights for developing healthier public transportation systems.

Bimetallic oxide Cu2O@MnO2 with exposed phase interfaces for dual-effect purification of indoor formaldehyde and pathogenic bacteria

The combination of materials with different functions is an optimal strategy for synchronously removing various indoor pollutants. For multiphase composites, exposing all components and their phase interfaces fully to the reaction atmosphere is a critical problem that needs to be solved urgently. Here, a bimetallic oxide Cu2O@MnO2 with exposed phase interfaces was prepared by a surfactant-assisted two-step electrochemical method, which shows a composite structure of non-continuously dispersed Cu2O particles anchored on flower-like MnO2. Compared with the pure catalyst MnO2 and bacteriostatic agent Cu2O, Cu2O@MnO2 respectively shows superior dynamic formaldehyde (HCHO) removal efficiency (97.2% with a weight hourly space velocity of 120 000 mL g-1 h-1) and pathogen inactivation ability (the minimum inhibitory concentration for 104 CFU mL-1 Staphylococcus aureus is 10 μg mL-1). According to material characterization and theoretical calculation, its excellent catalytic-oxidative activity is attributable to the electron-rich region at the phase interface which is fully exposed to the reaction atmosphere, inducing the capture and activation of O2 on the material surface, and then promoting the generation of reactive oxygen species that can be used for the oxidative-removal of HCHO and bacteria. Additionally, as a photocatalytic semiconductor, Cu2O further enhances the catalytic ability of Cu2O@MnO2 under the assistance of visible light. This work will provide efficient theoretical guidance and a practical basis for the ingenious construction of multiphase coexisting composites in the field of multi-functional indoor pollutant purification strategies.

Measurement methods and impact factors for the key parameters of VOC/SVOC emissions from materials in indoor and vehicular environments: A review

The emissions of volatile organic compounds (VOCs) and semi-volatile organic compounds (SVOCs) from indoor building and vehicle cabin materials can adversely affect human health. Many mechanistic models to predict the VOC/SVOC emission characteristics have been proposed. Nowadays, the main obstacle to accurate model prediction is the availability and reliability of the physical parameters used in the model, such as the initial emittable concentration, the diffusion coefficient, the partition coefficient, and the gas-phase SVOC concentration adjacent to the material surface. The purpose of this work is to review the existing methods for measuring the key parameters of VOCs/SVOCs from materials in both indoor and vehicular environments. The pros and cons of these methods are analyzed, and the available datasets found in the literature are summarized. Some methods can determine one single key parameter, while other methods can determine two or three key parameters simultaneously. The impacts of multiple factors (temperature, relative humidity, loading ratio, and air change rate) on VOC/SVOC emission behaviors are discussed. The existing measurement methods span very large spatial and time scales: the spatial scale varies from micro to macro dimensions; and the time scale in chamber tests varies from several hours to one month for VOCs, and may even span years for SVOCs. Based on the key parameters, a pre-assessment approach for indoor and vehicular air quality is introduced in this review. The approach uses the key parameters for different material combinations to pre-assess the VOC/SVOC concentrations or human exposure levels during the design stage of buildings or vehicles, which can assist designers to select appropriate materials and achieve effective source control.

Diurnal variation and potential sources of indoor formaldehyde at elementary school, high school and university in the Centre Val de Loire region of France

Formaldehyde (HCHO) is one of the abundant indoor pollutants and has been classified as a human carcinogen by the International Agency for Research on Cancer (IARC). Indoor HCHO at schools is particularly important due to the high occupancy density and the health effects on children. In this study, high time resolved measurement of formaldehyde concentration was conducted in the classrooms at elementary school, high school and university under normal students' activities in three different locations in the Region Centre Val de Loire-France. Indoor average formaldehyde concentrations at those three educational institutions were observed to be in the range 10.96-17.95 μg/m³, not exceeding the World Health Organization (WHO) guideline value of 100 μg/m³. As expected, ventilation was found playing an important role in the control of indoor formaldehyde concentration. After opening windows for 30 min, formaldehyde level decreased by ~25% and 38% in the classroom at the elementary school and the high school, respectively. In addition to the primary sources, the objective of this study was also to determine potential secondary sources of indoor formaldehyde in these schools by measuring the other volatile organic compounds (VOCs) present in the classrooms by a Proton Transfer Reaction Time-of-Flight Mass Spectrometry (PTR-ToF-MS). The measurements suggest that the release of residue from tobacco smokers is one of the major sources of indoor HCHO at the high school, which increases HCHO by ~55% averagely within 1 h. Moreover, the control experiments conducted in the university suggests that VOCs such as that released from cleaning products like terpenes, can contribute to the increase of indoor formaldehyde levels through chemical reactions with ozone. This study confirms simple recommendations to reduce the indoors HCHO concentration in schools: use ventilation systems, limit the emissions like cigarette smoke or cleaning products. It also points out that the secondary sources of formaldehyde must be also considered in the classroom.

Experimental and numerical investigation of TVOC concentrations and ventilation dilution in enclosed train cabin

Air pollution in trains is an important factor threatening human health, which has attracted more and more attention in the worldwide public health researches. In this study, one cabin of a fully enclosed train was taken as an example to conduct experimental and numerical research on pollution level and distribution characteristic of total volatile organic compound (TVOC). The results show that when the average emission rate under daily environmental conditions was taken as the reference, TVOC concentration in the cabin exceeded the limit level of Chinese Indoor Air Quality Standard by more than 4 times. The obvious pollutants accumulative phenomenon could be found at bottoms and corners under the action of airflow. Setting air inlets at the roof of the train, mean age of air ranged from 30 s to 50 s in the breathing area. The concentration of pollutants was the lowest at 2.5-5 m from the center point of the cabin structure, and the ventilation efficiency was the highest. The introduction of clean fresh air could effectively eliminate pollutants. When the complete displacement ventilation rates were 51.4 h^-1 and 28.6 h^-1, the removal efficiency of pollutants was about 0.85 and 0.48 mg/m³ per minute, respectively. This study was helpful to the improvement and optimization design of air quality and ventilation mode in trains.

Assessment of the mutagenicity of two common indoor air pollutants, formaldehyde and toluene

Traditionally, direct-reading instruments have been used to directly determine the concentrations of indoor air pollutants that may exceed the regulation limits. However, these instruments cannot directly assess the potential health hazards of these pollutants to humans. In this study, we developed and improved a bacterial reverse mutation assay (Ames test) by using a direct gas exposure module to directly determine the mutagenicity of indoor air quality using five tester bacterial strains (TA98, TA100, TA102, TA1535, and TA1537). Thereafter, the module was used to evaluate the effects of exposure time, different concentrations of HCHO or toluene, and mutagenic activities. We found that TA100 was the most sensitive strain and was reverted by relatively lower concentrations of 0.035 ppm HCHO. Furthermore, 50 ppm of toluene exposures caused a significant increase in the number of revertant colonies of TA100 without S9 activation at the 1.5-8-h exposure time intervals. Our findings provide new evidence that gaseous HCHO exposure could display weak but direct, time-dependent, and dose-dependent mutagenic activities. The weak, direct-acting, indirect-acting, and time-dependent mutagen of 50 ppm toluene was also confirmed. Moreover, our improved Ames module and the exposure conditions provided in this study can be further applied to evaluate the mutagenicity of indoor air quality.