Twigs-derived activated carbons via H3PO4/ZnCl2 composite activation for methylene blue and congo red dyes removal

Coconut shell carbon via phosphoric acid activation for rhodamine B, malachite green, and methylene blue adsorption - equilibrium and kinetics

This study was aimed at evaluating the removal of different cationic dyes onto phosphoric acid-activated coconut shell carbon. The activated carbon was characterized for surface functional groups, thermal decomposition profiles, surface morphology, and textural properties. The specific area was recorded as 1,221 m2/g with 100% mesoporosity. On molecular basis, the activated carbon adsorbs malachite green, methylene blue, and rhodamine B at maximum capacities of 1.52 mmol/g, 0.80 mmol/g, and 0.58 mmol/g, respectively. It indirectly implies the selectivity of activated carbon toward malachite green, and behaves differently due to steric hindrance of dye molecules. All equilibrium data obeyed Langmuir model, while the kinetic data are closely fitted to pseudo-second order model as concentration increases. To conclude, coconut shell activated carbon is more effective to remove malachite green compared to methylene blue and rhodamine B.

Valorizing date palm spikelets into activated carbon-derived composite for methyl orange adsorption: advancing circular bioeconomy in wastewater treatment-a comprehensive study on its equilibrium, kinetics, thermodynamics, and mechanisms

Leveraging date palm spikelets (DPS) as a precursor, this study developed a DPS-derived composite (ZnO@DPS-AC) for water treatment, focusing on methyl orange (MO) removal. The composite was synthesized through ZnCl2 activation and pyrolysis at 600 °C. Comprehensive characterization was conducted using TGA, FTIR, XRD, SEM/EDS, and pHPZC. Characterization revealed a highly carbonaceous material (> 74% carbon) with significant porosity and surface functional groups. ZnO@DPS-AC demonstrated rapid MO removal, achieving over 45% reduction within 10 min and up to 99% efficiency under optimized conditions. The Langmuir model-calculated maximum adsorption capacity reached 226.81 mg/g at 20 °C. Adsorption mechanisms involved hydrogen bonding, π-π interactions, and pore filling. The composite showed effectiveness in treating real wastewater and removing other pollutants. This study highlights the potential of agricultural waste valorization in developing efficient, sustainable adsorbents for water remediation, contributing to circular bioeconomy principles.

Cooperative production of monophenolic chemicals and carbon adsorption materials from cascade pyrolysis of acid hydrolysis lignin

A novel cascade pyrolysis upgrading process for acid hydrolysis lignin (AHL), consisting of pyrolysis, catalytic upgrading of pyrolysis vapors, and pyrolysis char, was developed to improve the yield of value-added products (monophenolic chemicals and carbon materials). Pyrolysis of AHL at 450 °C and subsequent catalytic upgrading of pyrolysis vapors over Ni/H-ZSM-5 boosted the concentration of monophenolic chemicals in pyrolysis liquids by 58%. The carbon material prepared from pyrolysis char using KOH as activating agent exhibited a large specific surface area of 2902.5 m2/g and a large total pore volume of 1.45 cm3/g, thus affording good adsorption capacity for methylene blue (824.87 mg/g) and iodine (2333.17 mg/g). Moreover, the cascade pyrolysis upgrading of AHL achieved a yield of 68.52% desired products, which was much higher than the reported results (single production of monophenols and pyrolysis char). In summary, this work provides a potential reference for efficient utilization of lignin in large-scale applications.

Adsorption and leaching of fluorotelomer compounds and perfluoroalkyl acids in aqueous media by activated carbon prepared from municipal biosolids

Perfluoroalkyl acids (PFAAs) are ubiquitous in nature and pose serious health risks to humans and animals. Limiting PFAA exposure requires novel technology for their effective removal from water. We investigated the efficacy of biosolid-based activated carbon (Bio-SBAC) in removing frequently detected PFAAs and their precursor fluorotelomer compounds at environmentally relevant concentrations (∼50 μg/L). Batch experiments were performed to investigate adsorption kinetics, isotherms, and leachability. Bio-SBAC achieved >95% removal of fluorotelomeric compounds, indicating that the need for PFAA removal from the environment could be minimised if the precursors were targeted. Kinetic data modelling suggested that chemisorption is the dominant PFAA adsorption mechanism. As evidenced by the isotherm modelling results, Freundlich adsorption intensity, n-1, values of <1 (0.707-0.938) indicate chemisorption. Bio-SBAC showed maximum capacities for the adsorption of perfluorooctanoic acid (1429 μg/g) and perfluorononanoic acid (1111 μg/g). Batch desorption tests with 100 mg/L humic acid and 10 g/L NaCl showed that Bio-SBAC effectively retained the adsorbed PFAA with little or no leaching, except perfluorobutanoic acid. Overall, this study revealed that Bio-SBAC is a value-added material with promising characteristics for PFAA adsorption and no leachability. Additionally, it can be incorporated into biofilters to remove PFAAs from stormwater, presenting a sustainable approach to minimise biosolid disposal and improve the quality of wastewater before discharge into receiving waters.

Upcycling of sugar refining mud solid waste as a novel adsorbent for removing methylene blue and Congo red from wastewater

The feasibility of utilizing the mud solid waste (MSW) produced during the carbonation process of sugar refining as a cost-effective and environmentally friendly alternative for the water removal of methylene blue (MB) and Congo red (CR), being highly utilized organic dyes representing cationic and anionic species, respectively is presented. Prior to its use, the MSW was dried at 110 °C for 24 h and sieved through a 100-mesh screen. The chief constituent of the MSW utilized was CaCO3, with a point of zero charge (PZC) found at pH 8.4 and 7.96 m2 g-1 total surface area. XRD and FTIR data indicate the presence of interactions between the dyes and the MSW surface, indicating effective adsorption. Different variables, such as initial dye concentration, MSW weight, solution pH, contact time, and temperature, were all examined to determine the optimal dye removal conditions. A central composite design (CCD) approach based on response surface methodology (RSM) modeling was utilized to identify statistically significant parameters for MB and CR adsorption capacities onto the MSW adsorbent. The removal equilibrium was typically reached in 120 minutes, with the greatest removal efficiency of CR taking place at pH 2 and 328 K, while the highest MB removal efficiency was obtained at pH 12 and 296 K. Kinetic studies suggest the adsorption of both dyes on the MSW follow pseudo-second-order rates, as evident through the high correlations obtained. Linearized and non-linearized Langmuir models showed strong correlations indicating maximum adsorption capacities of 86.6 and 72.3 mg g-1 for MB and CR, respectively. High regeneration and reusability potential of the MSW was demonstrated especially for the adsorption of CR, where the removal efficiency was nearly constant throughout five adsorption cycles, ranging from 93 to 91%, while the reduction in the removal for MB was much more significantly impacted, diminishing from 95 to 79% after the five cycles.

Sequentially optimized process towards sustainable synthesis of activated carbon from wild thornbush for 4-nitrophenol and industrial effluent treatment

Environmental nuisance thornbush Prosopis juliflora was utilized as an inexpensive and renewable biomass raw material for the sustainable production of activated carbon. Previously, the sequential muffle furnace-microwave arrangement was effective with acid activation for activated carbon synthesis. However, the intermediate synthesis steps were not optimized. In this work, we have optimized the intermediate steps, viz. chemical impregnation, carbonization, and microwave activation. Sequential optimization for base activation was developed and compared with acid activation. The base-activated carbon (BAC) exhibited a more crystalline nature and faster uptake kinetics than AAC. BAC demonstrated an adsorption capacity of 576 mg/g for 4-nitrophenol (4-NP) surpassing that of optimized acid-activated carbon (AAC) by 45%. The optimal base activation required 1.85 times lower microwave energy than that of the acid activation. BAC exhibited significantly higher BET surface area (1319 m2/g) and micropore volume (0.524 cm3/g) which were about 28% and 26% higher than those of AAC. When compared to biochar obtained from the same thornbush, the BAC exhibited an 11-fold increase in adsorption capacity. The adsorbents could be easily regenerated with ethanol and used up to five cycles. Adsorption using BAC also could achieve 80% COD removal for industrial wastewater, while AAC led to 61% removal. Continuous packed column with BAC revealed a breakthrough time of 3.5 h for industrial effluent while for 500 mg/L 4-nitrophenol, it was 25 h. Prosopis juliflora thornbush, an environmental nuisance, could be converted into a high-capacity adsorbent for environmental remediation after careful sequencing and optimization of the intermediate synthesis steps.

Sustainability, performance, and production perspectives of waste-derived functional carbon nanomaterials towards a sustainable environment: A review

The survival of humanity is severely threatened by the massive accumulation of waste in the ecosystem. One plausible solution for the management and upcycling of waste is conversing waste at the molecular level and deriving carbon-based nanomaterial. The field of carbon nanomaterials with distinctive properties, such as exceptionally large surface areas, good thermal and chemical stability, and improved propagation of charge carriers, remains a significant area of research. The study demonstrates recent developments in high-value carbon-based photocatalysts synthesis from various waste precursors, including zoonotic, phytogenic, polyolefinic, electronic, and biomedical, highlighting the progression as photocatalysts and adsorbents for wastewater treatment and water splitting applications. This review highpoints the benefits of using waste as a precursor to support sustainability and circular economy and the risks associated with their use. Finally, we support that a sustainable society will eventually be realized by exploring present obstacles and potential steps for creating superior carbon-based nanomaterials in the future.

Spherical Lignin-Derived Activated Carbons for the Adsorption of Phenol from Aqueous Media

In this work, a synthesis and activation path, which enabled the preparation of spherical activated carbon from a lignin precursor, characterized by high adsorption capacity in the removal of phenolic compounds from water, was successfully developed. Two industrial by-products, i.e., Kraft lignin and sodium lignosulfonate, were used to form spherical nanometric lignin grains using pH and solvent shift methods. The obtained materials became precursors to form porous activated carbons via chemical activation (using K2CO3 or ZnCl2 as activating agents) and carbonization (in the temperature range of 600-900 °C). The thermal stabilization step at 250 °C was necessary to ensure the sphericity of the grains during high-temperature heat treatment. The study investigated the influence of the type of chemical activator used, its quantity, and the method of introduction into the lignin precursor, along with the carbonization temperature, on various characteristics including morphology (examined by scanning electron microscopy), the degree of graphitization (evaluated by powder X-ray diffraction), the porosity (assessed using low-temperature N2 adsorption), and the surface composition (analyzed with X-ray photoelectron spectroscopy) of the produced carbons. Finally, the carbon materials were tested as adsorbents for removing phenol from an aqueous solution. A conspicuous impact of microporosity and a degree of graphitization on the performance of the investigated adsorbents was found.

Solvatochromism as a Novel Tool to Enumerate the Optical and Luminescence Properties of Plastic Waste Derived Carbon Nanodots and Their Activated Counterparts

Herein, we have developed a one-pot methodology to synthesise three types of C-dots and their activated counterparts from three different types of waste plastic precursors such as poly-bags, cups and bottles. The optical studies have shown the significant change in the absorption edge in case of C-dots in comparison to their activated counterparts. The respective variation in the sizes is correlated with the change in electronic band gap values of formed particles. The changes in the luminescence behaviour are also correlated with transitions from the edge of the core of formed particles. The obtained variations in the Stokes shift values of C-dots, and their ACs were used to explore the types of surface states and their related transitions in particles. The mode of interaction between C-dots and their ACs was also determined using solvent-dependent fluorescence spectroscopy. This detailed investigation could provide significant insight on the emission behaviour and the potential usage of formed particles as an effective fluorescent probe in sensing applications.

Synthesis of Activated Porous Carbon from Red Dragon Fruit Peel Waste for Highly Active Catalytic Reduction in Toxic Organic Dyes

In this study, an alternative precursor for production of biomass-derived activated carbon was introduced using dragon fruit (Hylocereus costaricensis) peels. Chemical activators such as FeCl3, MgCl2, ZnCl2 were used in the thermal carbonization process to convert carbon into porous carbon (PC). However, heteroatom-doped PC catalysts including N-, B-, and P-doped carbon catalysts in the field of dye removal is highly desirable. Several approaches (XRD, FE-SEM/TEM, XPS, FT-IR, EDS, and elemental mapping) were employed to examine the surface morphology, surface properties, and elemental composition of the PC catalyst. The catalytic activity of metal-free PC catalyst was demonstrated for methylene blue (MB), crystal violet (CV), and Nile blue (NB) in a mild environment The corresponding rate constant (kapp) values were estimated as 0.2473, 0.3248, and 0.3056 min−1, respectively, for MB, CV, and NB, which were significantly greater than those of numerous reports. It exhibited the best catalytic activity and recyclability. Moreover, the approach proposed here could create new opportunities for the remediation of organic dyes in lakes and industrial wastewater.

Mathematical analysis of the effect of process conditions on the porous structure development of activated carbons derived from Pine cones

This paper presents the results of a study on the influence of the degree of impregnation and activation temperature on the formation of the porous structure of activated carbons (ACs) obtained from Pine cones by the chemical activation process using potassium hydroxide as an activator. The advanced new numerical clustering based adsorption analysis (LBET) method, together with the implemented unique numerical procedure for the fast multivariant identification were applied to nitrogen and carbon dioxide adsorption isotherms determined for porous structure characterization of the ACs. Moreover, the Quenched Solid Density Functional Theory (QSDFT) method was chosen to determine pore size distributions. The results showed a significant influence of the primary structure of Pine cones on the formation of the porous structure of the developed ACs. Among others, it was evidenced by a very high degree of surface heterogeneity of all the obtained ACs, irrespective of the degree of impregnation with potassium hydroxide and the activation temperature. Moreover, the analysis of carbon dioxide adsorption isotherms showed, that the porous structure of the studied ACs samples contains micropores accessible only to carbon dioxide molecules. The results also showed a significant advantage of the LBET method over those conventionally used for porous structure analysis based on Brunauer–Emmett–Teller (BET) and Dubinin–Raduskevich (DR) equations, because it takes into account surface heterogeneities. The novel analyses methods were more fully validated as a reliable characterization tool, by extending their application to the isotherms for ACs developed from the same precursor by phosphoric acid activation, and for samples arising from these ACs, further subjected to additional post-treatments. The effect of the raw material used as precursor was moreover analysed by comparison with previous reported results for other ACs. The complementarity of the results obtained with the LBET and QSDFT methods is also noteworthy, resulting in a more complete and reliable picture of the analyzed porous structures.

Efficient liquid phase confiscation of nile blue using a novel hybrid nanocomposite synthesized from guar gum-polyacrylamide and erbium oxide

In recent times, biopolymer-metal oxide nanocomposites have gained prominent importance in the attenuation of environmental toxicants from aqueous phase. But lanthanide oxide-based biopolymer nanocomposites have scantly been evaluated for their adsorption potential. A novel guar gum-polyacrylamide/erbium oxide nanocomposite (GG-PAAm/Er₂O₃ NC) adsorbent was synthesized by copolymerization of guar gum (GG) and acrylamide (AAm) utilizing N-N′-methylenebisacrylamide as a crosslinker and Er₂O₃ as a reinforcing agent. The adsorptive efficacy of GG-PAAm/Er₂O₃ nanocomposite was evaluated using nile blue (NB) as a model pollutant dye from aquatic system. The prepared adsorbent was characterized by Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) analysis, Brunauer–Emmett–Teller (BET) analysis, thermogravimetric analysis, scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM–EDX), and high-resolution transmission electron microscopy (HRTEM). The optimal process parameters, which include dosage (0.8 g/L), agitation time (40 min), initial solution pH (6), and initial NB concentration (80 mg/L) were determined by batch methodology. The equilibrium data for NB confiscation was better expressed by Langmuir isotherm model, with maximal adsorption effectiveness (Q_m) of 225.88 mg NB/g demonstrating the actively monolayer adsorption onto homogeneous surface of GG-PAAm/Er₂O₃ NC. The kinetics of NB sorption process onto GG-PAAm/Er₂O₃ NC was reliable with pseudo-second order model. Thermodynamic parameters such as ΔH^° (15–17 kJ/mol) and ΔS^° (0.079–0.087 kJ/mol/K), and − ΔG^° (8.81–10.55 kJ/mol) for NB validated the endothermic, an increased randomness at the GG-PAAm/Er₂O₃–NB interface, and spontaneity and feasibility of the process, respectively. The spent nanocomposite was effectively regenerated with NaOH, and could be reused proficiently for five runs demonstrating the high reusability potential of the nanocomposite. The commendable removal efficiency and high reusability of GG-PAAm/Er₂O₃ NC recommended it to be a highly competent adsorbent for cationic dyes particularly NB diminution from aqueous waste.

Two-stage adsorber optimization of NaOH-prewashed oil palm empty fruit bunch activated carbon for methylene blue removal

The objective of the present work was to evaluate the performance of two-stage adsorber of activated carbon from oil palm empty fruit bunch for methylene blue removal. The model was developed to predict optimum adsorbent mass and time at a specified volumes and concentrations of dye solution. Results show that the adsorbent mass can be reduced by 6.67%. Operating time taken to attain the equilibrium in a two-stage adsorber has dramatically decreased from 22 h to 0.52 h. In the performance evaluation, the adsorbent mass in stage-1 is higher than in stage-2, which lessen the workload to achieve equilibrium. A two-stage adsorber aids to optimize the mass and contact time for different percentage of dye removal that economically feasible for industrial applications.

Adsorption behavior of Congo red on a carbon material based on humic acid

Humic acid is used as an inexpensive starting material to prepare a strong adsorbent for the removal of Congo red from water.

Development and Characterization of Activated Carbon from Olive Pomace: Experimental Design, Kinetic and Equilibrium Studies in Nimesulide Adsorption

The lack of adequate treatment for the removal of pollutants from domestic, hospital and industrial effluents has caused great environmental concern. Therefore, there is a need to develop materials that have the capacity to treat these effluents. This work aims to develop and characterize an activated charcoal from olive pomace, which is an agro-industrial residue, for adsorption of Nimesulide in liquid effluent and to evaluate the adsorption kinetics and equilibrium using experimental design. The raw material was oven dried at 105 °C for 24 h, ground, chemically activated in a ratio of 1:0.8:0.2 of olive pomace, zinc chloride and calcium hydroxide and thermally activated by pyrolysis in a reactor of stainless steel at 550 °C for 30 min. The activated carbon was characterized by Fourier Transform Infrared (FTIR) spectroscopy, X-ray Diffractometry (XRD), Brunauer, Emmett and Teller (BET) method, Thermogravimetric Analysis (TGA), Scanning Electron Microscopy (SEM), density and zero charge potential analysis. The surface area obtained was 650.9 m² g⁻¹. The kinetic and isothermal mathematical models that best described the adsorption were PSO and Freundlich and the highest adsorption capacity obtained was 353.27 mg g⁻¹. The results obtained showed the good performance of activated carbon produced from olive pomace as an adsorbent material and demonstrated great potential for removing emerging contaminants such as Nimesulide.