Preparation of hexagonal nanoporous Al2O3/TiO2/TiN as a novel photodetector with high efficiency

β-Cyclodextrin/Zn-Fe layered double hydroxides/graphitic carbon nitride nanomaterials based potentiometric sensor for paroxetine determination in environmental water samples

Developing targeted and sensitive analytical techniques for drug monitoring in different specimens are of utmost importance. Herein, a first attempt was made for the determination of paroxetine (Prx+) in environmental water samples using a novel, sensitive, selective, stable, accurate and eco-friendly potentiometric sensor based on Zn-Fe layered double hydroxides/graphitic carbon nitride (Zn-Fe LDH/g-C3N4) nanomaterials with β-cyclodextrin (β-CD) as the sensing ionophore and dibutyl phthalate (DBP) as the plasticizer. The prepared nanomaterial was characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The surface properties of the proposed sensor were characterized by electrochemical impedance spectroscopy (EIS). The sensor exhibited an excellent Nernstian slope of 59.3 ± 0.7 mV decade-1 covering a wide linear working range of 1.0 × 10-6 to 1.0 × 10-2 mol L-1, low detection limit of 3.0 × 10-7 mol L-1, low quantification limit of 9.9 × 10-7 mol L-1, long life time, sufficient selectivity, high chemical and thermal stability within a wide pH range of 2.0-9.0. This analytical method was successfully implemented for Prx+ determination in a pure form, pharmaceutical formulation and different water samples.

Mechanism and growth kinetics of hexagonal TiO2 nanotubes with an influence of anodizing parameters on morphology and physical properties

Hexagonal TiO2 nanotubes (hTNTs) mimic a honeycomb structure, indicating their high potential as implantable materials due to their superior mechanical, chemical, and biological properties. However, the fabrication of hTNTs with a hexagonal base and six rectangular sides poses significant challenges, underscoring the importance of this research. This study developed a novel sonoelectrochemical method for synthesizing uniform hTNTs and evaluated the influence of anodizing parameters on their morphology. The effects of electrolyte concentration (ethylene glycol 90-97.5% and ammonium fluoride 0.1-0.5 wt%) and anodizing parameters (time 5-90 min, potential 10-80 V) on the morphology (diameter and length) and physical properties (porosity, specific surface area, growth factor) of hTNTs were investigated using scanning electron microscopy and anodization analysis. The methodology enabled the synthesis of hTNTs with diameters ranging from 33 ± 3 nm to 203 ± 33 nm and lengths from 1.16 ± 0.04 μm to 20.93 ± 2.37 μm. The study demonstrated that the concentrations of ethylene glycol and ammonium fluoride influenced the diameter and length of hTNTs depending on the anodizing potential. Moreover, the anodizing potential significantly affected the diameter, while both potential and time impacted the length of hTNTs. The proposed method can modify material surfaces for diverse applications.

Recent Progress in Photodetectors: From Materials to Structures and Applications

Photodetectors are critical components in a wide range of applications, from imaging and sensing to communications and environmental monitoring. Recent advancements in material science have led to the development of emerging photodetecting materials, such as perovskites, polymers, novel two-dimensional materials, and quantum dots, which offer unique optoelectronic properties and high tunability. This review presents a comprehensive overview of the synthesis methodologies for these cutting-edge materials, highlighting their potential to enhance photodetection performance. Additionally, we explore the design and fabrication of photodetectors with novel structures and physics, emphasizing devices that achieve high figure-of-merit parameters, such as enhanced sensitivity, fast response times, and broad spectral detection. Finally, we discuss the demonstration of new applications enabled by these advanced photodetectors, including flexible and wearable devices, next-generation imaging systems, and environmental sensing technologies. Through this review, we aim to provide insights into the current trends and future directions in the field of photodetection, guiding further research and development in this rapidly evolving area.

Crystalline Mesoporous F-Doped Tin Dioxide Nanomaterial Successfully Prepared via a One Pot Synthesis at Room Temperature and Ambient Pressure

We report the successful one pot synthesis of crystalline mesoporous tin dioxide powder doped with fluoride at ambient pressure and temperature. This material possesses a high surface area, narrow pore size distribution, small average crystallite sizes, and good opto-electrical properties. The existence of fluorine increased the opto-electronic activity of tin dioxide by 20 times, and conductivity by 100 times compared with pristine tin dioxide prepared via the same method. The conductivity of SnO2 in air at 25 °C is 5 × 10-5 S/m, whereas that of F-SnO2 is 4.8 × 10-3 S/m. The structures of these materials were characterized with powder X-ray diffraction, N2 sorption analysis, transmission electron microscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, and UV-visible spectroscopy. Fluorine occupies the framework of tin dioxide by replacing some of the oxygen atoms. The structure, conductance, and optical properties of these materials are discussed in this paper.

Decoration of Poly-3-methyl Aniline with As(III) Oxide and Hydroxide as an Effective Photoelectrode for Electroanalytical Photon Sensing with Photodiode-like Behavior

This study achieved the decoration of poly-3-methyl aniline (P3MA) with As2O3-As(OH)3 using K2S2O8 and NaAsO2 on the 3-methyl aniline monomer. This resulted in a highly porous nanocomposite polymer composite with wide absorption optical behavior, an average crystalline size of 22 nm, and a 1.73 eV bandgap. The photoelectrode exhibited a great electrical response for electroanalytical applications, such as photon sensing and photodiodes, with a Jph of 0.015 mA/cm2 and Jo of 0.004 mA/cm2. The variable Jph values ranged from 0.015 to 0.010 mA/cm2 under various monochromatic filters from 340 to 730 nm, which demonstrates high sensitivity to wavelengths. Effective photon numbers were calculated to be 8.0 × 1021 and 5.6 × 1021 photons/s for these wavelength values, and the photoresponsivity (R) values were 0.16 and 0.10 mA/W, respectively. These high sensitivities make the nanocomposite material a promising candidate for use in photodetectors and photodiodes, with potential for commercial applications in highly technological systems and devices. Additionally, the material opens up possibilities for the development of photodiodes using n- and p-type materials.

Directional and Eye-Tracking Light Field Display with Efficient Rendering and Illumination

Current efforts with light field displays are mainly concentrated on the widest possible viewing angle, while a single viewer only needs to view the display in a specific viewing direction. To make the light field display a practical practice, a super multi-view light field display is proposed to compress the information in the viewing zone of a single user by reducing the redundant viewpoints. A quasi-directional backlight is proposed, and a lenticular lens array is applied to achieve the restricted viewing zone. The eye-tracking technique is applied to extend the viewing area. Experimental results show that the proposed scheme can present a vivid 3D scene with smooth motion parallax. Only 16.7% conventional light field display data are required to achieve 3D display. Furthermore, an illumination power of 3.5 watt is sufficient to lighten a 31.5-inch light field display, which takes up 1.5% of the illumination power required for planar display of similar configuration.

Ag2S-Ag2O-Ag/poly-2-aminobenzene-1-thiol Nanocomposite as a Promising Two-Electrode Symmetric Supercapacitor: Tested in Acidic and Basic Mediums

A Ag₂S-Ag₂O-Ag/poly-2-aminobenzene-1-thiol (P2ABT) nanocomposite was prepared using the photopolymerization reaction using AgNO₃ as an oxidant. The size of the nanocomposite was about 40 nm, in which the morphology was confirmed using TEM and SEM analyses. The functional groups of Ag₂S-Ag₂O-Ag/P2ABT were confirmed using FTIR; also, XRD confirmed the inorganic Ag₂S, Ag, and Ag₂O formation. This nanocomposite has great performance in supercapacitor applications, with it tested in acidic (1.0 M HCl) and basic mediums (1.0 M NaOH). This pseudo-capacitor has great performance that appeared through the charge time in an acid medium in comparison to the basic medium with values of 118 s and 103 s, correspondingly. The cyclic voltammetry (CV) analysis further confirmed the excellent performance of the supercapacitor material, as indicated by the large area under the cyclic curve. The specific capacitance (C_S) and energy density (E) values (at 0.3 A/g) were 92.5 and 44.4 F/g and 5.0 and 2.52 W·h·Kg^-1 in the acidic and basic mediums, correspondingly. The charge transfer was studied through a Nyquist plot, and the produced R_s values were 4.9 and 6.2 Ω, respectively. Building on these findings, our objective is to make a significant contribution to the progress of supercapacitor technology through a prototype design soon.

Highly Uniform Multi-Layers Reduced Graphene Oxide/Poly-2-aminobenzene-1-thiol Nanocomposite as a Promising Two Electrode Symmetric Supercapacitor under the Effect of Absence and Presence of Porous-Sphere Polypyrrole Nanomaterial

A uniform and highly porous reduced graphene oxide/poly-2-aminobenzene-1-thiol multi-layer (R-GO/P2ABT-ML) nanocomposite was synthesized and characterized. The uniform layer structure and porosity of the nanocomposite, combined with its conductivity, make it an ideal candidate for use as a pseudo supercapacitor. To enhance the capacitance behavior, a porous ball structure polypyrrole (PB-Ppy) was incorporated into the nanocomposite. When tested at 0.2 A/g, the capacitance values of the R-GO/P2ABT-ML and R-GO/P2ABT-ML/PB-Ppy were found to be 19.6 F/g and 92 F/g, respectively, indicating a significant increase in capacitance due to the addition of PB-Ppy. The energy density was also found to increase from 1.18 Wh.kg^-1 for R-GO/P2ABT-ML to 5.43 Wh.kg^-1 for R-GO/P2ABT-ML/PB-Ppy. The stability of the supercapacitor was found to be significantly enhanced by the addition of PB-Ppy. The retention coefficients at 100 and 500 charge cycles for R-GO/P2ABT-ML/PB-Ppy were 95.6% and 85.0%, respectively, compared to 89% and 71% for R-GO/P2ABT-ML without PB-Ppy. Given the low cost, mass production capability, and easy fabrication process of this pseudo capacitor, it holds great potential for commercial applications. Therefore, a prototype of this supercapacitor can be expected to be synthesized soon.

Photodetection Enhancement via Graphene Oxide Deposition on Poly 3-Methyl Aniline

A graphene oxide (GO)/poly 3-methyl aniline (P3MA) photodetector has been developed for light detection in a broad optical region: UV, Vis, and IR. The 3-methyl aniline was initially synthesized via radical polymerization using an acid medium, i.e., K₂S₂O₈ oxidant. Consequently, the GO/P3MA composite was obtained through the adsorption of GO into the surface of P3MA. The chemical structure and optical properties of the prepared materials have been illustrated via XRD, FTIR, SEM, and TEM analysis. The absorbance measurements demonstrate good optical properties in the UV, Vis, and near-IR regions, although a decrease in the bandgap from 2.4 to 1.6 eV after the composite formation was located. The current density (J_ph) varies between 0.29 and 0.68 mA·cm^-2 (at 2.0 V) under dark and light, respectively. The photodetector has been tested using on/off chopped light at a low potential, in which the produced J_ph values decrease from 0.14 to 0.04 µA·cm^-2, respectively. The GO/P3MA photodetector exhibits excellent R (and D) values of 4 and 2.7 mA·W^-1 (0.90 × 10⁹ and 0.60 × 10⁹ Jones) in the UV (340 nm) and IR (730 nm) regions, respectively. The R and D values obtained here make the prepared photodetector a promising candidate for future light detection instruments.

MoO3/S@g-C3N4 Nanocomposite Structures: Synthesis, Characterization, and Hydrogen Catalytic Performance

Hydrogen production as a source of clean energy is high in demand nowadays to avoid environmental issues originating from the use of conventional energy sources i.e., fossil fuels. In this work and for the first time, MoO₃/S@g-C₃N₄ nanocomposite is functionalized for hydrogen production. Sulfur@graphitic carbon nitride (S@g-C₃N₄)-based catalysis is prepared via thermal condensation of thiourea. The MoO₃, S@g-C₃N₄, and MoO₃/S@g-C₃N₄ nanocomposites were characterized using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Field Emission Scanning Electron Microscope (FESEM), STEM, and spectrophotometer. The lattice constant (a = 3.96, b = 13.92 Å) and the volume (203.4 ų) of MoO₃/10%S@g-C₃N₄ were found to be the highest compared with MoO₃, MoO₃/20-%S@g-C₃N₄, and MoO₃/30%S@g-C₃N₄, and that led to highest band gap energy of 4.14 eV. The nanocomposite sample MoO₃/10%S@g-C₃N₄ showed a higher surface area (22 m²/g) and large pore volume (0.11 cm³/g). The average nanocrystal size and microstrain for MoO₃/10%S@g-C₃N₄ were found to be 23 nm and -0.042, respectively. The highest hydrogen production from NaBH₄ hydrolysis ~22,340 mL/g·min was obtained from MoO₃/10%S@g-C₃N₄ nanocomposites, while 18,421 mL/g·min was obtained from pure MoO₃. Hydrogen production was increased when increasing the masses of MoO₃/10%S@g-C₃N₄.

Photoelectrochemical Conversion of Sewage Water into H2 Fuel over the CuFeO2/CuO/Cu Composite Electrode

This study describes the synthesis of delafossite, CuFeO2, as a primary photocatalytic material for hydrogen generation. A photoelectrode, CuFeO2/CuO/Cu, was prepared by combusting a Cu foil dipped in FeCl3 in ambient air. This photoelectrode showed excellent optical behavior for the hydrogen generation reaction from sewage water, producing 90 µmol/h of H2. The chemical structure was confirmed through XRD and XPS analyses, and the crystalline rhombohedral shape of CuFeO2 was confirmed using SEM and TEM analyses. With a bandgap of 1.35 ev, the prepared material displayed excellent optical properties. Electrochemical measurements for H2 gas generation were carried out using the CuFeO2/CuO/Cu photoelectrode, comparing the effect of light and dark and monochromatic wavelength light. The electrode exhibited significant enhancement in light compared to dark, with current density (Jph) values of −0.83 and −0.1 mA·cm−2, respectively. The monochromatic light also had a noticeable effect, with the Jph value increasing from −0.45 to −0.79 mA·cm−2 as the wavelength increased from 640 to 390 nm. This system is cheap and durable, making it a promising solution for hydrogen gas fuel generation in the industry.

Alkallas F, M. Ahmed A, Rabia M. Petal-like NiS-NiO/G-C3N4 Nanocomposite for High-Performance Symmetric Supercapacitor

Graphitic carbon nitride (G-C3N4) and NiS-NiO/G-C3N4 nanocomposite have been synthesized via combustion and hydrothermal techniques, respectively. The chemical and morphological properties of these materials were confirmed using different analytical methods. SEM confirms the formation of G-C3N4 sheets containing additional petal-like shapes of NiS-NiO nanoparticles. The electrochemical testing of NiS-NiO/G-C3N4 symmetric supercapacitors is carried out from 0.6 M HCl electrolyte. Such testing includes charge/discharge, cyclic voltammetry, impedance, and supercapacitor stability. The charge/discharge time reaches 790 s at 0.3 A/g, while the cyclic voltammetry curve forms under a high surface area. The produced specific capacitance (C_S) and energy density values are 766 F/g and 23.55 W.h.kg^-1, correspondingly.

Development of a Highly Efficient Optoelectronic Device Based on CuFeO2/CuO/Cu Composite Nanomaterials

Herein, an optoelectronic device synthesized from a CuFeO₂/CuO/Cu nanocomposite was obtained through the direct combustion of Cu foil coated with Fe₂O₃ nanomaterials. The chemical, morphological, and optical properties of the nanocomposite were examined via different techniques, such as XRD, XPS, TEM, SEM, and UV/Vis spectrophotometer. The optical reflectance demonstrated a great enhancement in the CuFeO₂ optical properties compared to CuO nanomaterials. Such enhancements were clearly distinguished through the bandgap values, which varied between 1.35 and 1.38 eV, respectively. The XRD and XPS analyses confirmed the chemical structure of the prepared materials. The produced current density (J_ph) was studied in dark and light conditions, thereby confirming the obtained optoelectronic properties. The J_ph dependency to monochromatic wavelength was also investigated. The J_ph value was equal to 0.033 mA·cm^-2 at 390 nm, which decreased to 0.031 mA·cm^-2 at 508 nm, and then increased to 0.0315 mA·cm^-2 at 636 nm. The light intensity effects were similarly inspected. The J_ph values rose when the light intensities were augmented from 25 to 100 mW·cm^-2 to reach 0.031 and 0.05 mA·cm^-2, respectively. The photoresponsivity (R) and detectivity (D) values were found at 0.33 mA·W^-1 and 7.36 × 10¹⁰ Jones at 390 nm. The produced values confirm the high light sensitivity of the prepared optoelectronic device in a broad optical region covering UV, Vis, and near IR, with high efficiency. Further works are currently being designed to develop a prototype of such an optoelectronic device so that it can be applied in industry.

Influence of Doping-Ion-Type on the Characteristics of Al2O3-Based Nanocomposites and Their Capabilities of Removing Indigo Carmine from Water

Globally, the continuous contamination of natural water resources is a severe issue, and looking for a solution for such a massive problem should be the researcher’s concern. Herein, Al2O3, Al2O3-CuO, Al2O3-NiO, and Al2O3-CoO were prepared via a simple and fast route, utilizing glucose as a capping material. All synthesis conditions were uniform to make the fabricated nanomaterials’ characteristics exclusively influenced by only the ion type. The SEM analysis showed that the particles of the synthesized Al2O3, Al2O3-CuO, Al2O3-NiO, and Al2O3-CoO were all less than 25 nm. The Al2O3-NiO showed the smallest particle size (11 to 14 nm) and the best BET surface area of 125.6 m2 g−1. All sorbents were tested for removing organic pollutants, as exemplified by indigo carmine (IGC) dye. The Al2O3-NiO possessed the highest adsorption capacity among the other sorbents for which it had been selected for further investigations. The IGC sorption reached equilibrium within 2.0 h, and the kinetic study revealed that the IGC removal by Al2O3-NiO nanocomposite fitted the FOM and the LFM. The sorbent showed an experimental adsorption capacity (qt) of 456.3 mg g−1 from a 200 mg L−1 IGC solution and followed the Langmuir model. The thermodynamic findings indicated an endothermic, spontaneous, and physisorption nature. The seawater and groundwater samples contaminated with 5.0 mg L−1 IGC concentrations were fully remediated using the Al2O3-NiO nanocomposite. The reuse study showed 93.3% average efficiency during four successive cycles. Consequently, prepared Al2O3-NiO nanocomposite is recommended for the treatment of contaminated water.

ATO/Polyaniline/PbS Nanocomposite as Highly Efficient Photoelectrode for Hydrogen Production from Wastewater with Theoretical Study for the Water Splitting

Polyaniline-assisted deposition of PbS is carried out on antimony tin oxide (ATO) glass for ATO/PANI/PbS composite formation. The deposition of PbS was carried out inside and outside the polymer chains using the ionic adsorption deposition process. Various analyses were conducted to confirm the chemical structure and morphological, optical, and electrical properties of the resulting composite. TEM and SEM analyses demonstrated the spherical shape of PbS particles inside and outside the PANI network with more dark or white color, respectively. Moreover, the ImageJ program confirmed the composite formation. The XRD characterization showed the shifts in the PANI peaks after the composite formation with the appearance of a new additional peak related to PbS nanoparticles. The optical analyses were massively enhanced after the composite formation with more broadening in the Vis region at 630 nm, in which there was more enhancement in the bandgap that reached 1.5 eV. The electrode application in the H2 generation process was carried out from wastewater (sewage water, third treatment) without any additional sacrificing agent. The electrode responded well to light, where the current density ( $J_{\text{ph}}$ ) changed from 10-6 to 0.13 mA.cm-2 under dark and light, respectively. The electrode had high reproducibility and stability. The numbers of generated H2 moles were 0.1 mmol/cm2.h. The produced ${\Delta H}^{\ast }$ and ${\Delta S}^{\ast }$ were 7.3 kJ/mol and 273.4 J/mol.K, respectively. Finally, the mechanism explains the H2 generation reaction using three-electrode cell.

Poly-3-Methyl Aniline-Assisted Spherical PbS Quantum Dots through the Ionic Adsorption Deposition Method as a Novel and Highly Efficient Photodetector in UV, Vis, and NIR Regions

This study describes the preparation and characterization of glass/poly-3-methyl aniline (P3MA)/PbS quantum dot (QD) optoelectronic photodetector to detect and sense the light in broad spectral regions of UV, Vis, and NIR. This work is carried out to solve the drawbacks of other studs that prepare detectors in just one or two optical regions. Previous studies have used high-priced techniques. The deposition of P3MA on the glass surface was carried out by in situ oxidation process. Then, this polymer film was used to assist the deposition of PbS-QD particles through the ionic adsorption deposition method. The latter was performed using four different concentrations of Pb(NO3)2 solution (0.01, 0.03, 0.05, and 0.07 M) to form four P3MA/PbS composites: I, II, III, and IV, respectively. The chemical structure, morphologies, and electrical and optical properties of these composites were determined using different analytical tools. The SEM confirmed the formation of spherical QD particles of PbS on the P3MA surface. The TEM analysis showed that the composite has an average size of 5 nm, with the interatomic distances of 0.4 nm. Furthermore, the optical band gap values were 1.53, 1.52, 1.50, and 1.51 eV, respectively. The optoelectronic device could detect and sense light from 390 to 636 nm under various optical wavelengths. The produced current density ( $J_{\text{ph}}$ ) values decreased from 0.029 mA.cm-2 at 390 nm to 0.022 mA.cm-2 at 500 nm and then increased until 0.024 mA.cm-2 at 636 nm. The light sensing was determined through the photoresponsivity ( $R$ ) and detectivity ( $D$ ) parameters, in which the photodetector has $R$ and $D$ values of 0.29 mA.cm-2 and $6.5\times {10}^7$ Jones, respectively. Finally, a simple mechanism was proposed to explain the light sensing through the prepared optoelectronic device. Soon, our team works on the industrial applications of this optoelectronic device in the industry field related to the great optoelectronic device technical properties and its low cost and easy preparation.

Bunch of Grape-Like Shape PANI/Ag2O/Ag Nanocomposite Photocatalyst for Hydrogen Generation from Wastewater

Polyaniline (PANI) and PANI/Ag2O/Ag composites I and II were prepared under different AgNO3 oxidant concentrations using the oxidative photopolymerization method. The chemical structure and optical, electrical, and morphological properties were determined for the prepared nanocomposite. The PANI/Ag2O/Ag composite II has the optimum optical properties, in which the bandgaps of PANI, composite I, and composite II are 3.02, 1.71, and 1.68 eV, respectively, with the morphology of a bunch of grape-like shapes with average particles sizes of 25 nm. Under the optimum optical properties, glass/PANI/Ag2O/Ag composite II electrode is used for hydrogen generation from sewage water. The measurements are carried out from a three-electrode cell under a xenon lamp. The effects of light wavelengths and temperature on the produced current density ( $J_{\text{ph}}$ ) are mentioned. Under the applied voltage (at 30°C), the current density values ( $J_{\text{ph}}$ ) increase from 0.003 to 0.012 mA.cm-2 in dark and light, respectively. While increasing the temperature, $J_{\text{ph}}$ values increase to 0.032 mAcm-2 at 60°C. The thermodynamic parameters are calculated, in which the activation energy ( $E_{\text{a}}$ ), enthalpy ( $\Delta H\ast$ ), and entropy ( $\Delta S\ast$ ) values are 27.1 kJ·mol-1, 24.5 J mol-1, and 140.5 J K-1 mol-1, respectively. Finally, a simple mechanism for the produced hydrogen generation rate is mentioned. The prepared electrode is a very cheap (1$ for $12\ast 12\text{c}{\text{m}}^2$ ) electrode.

Conversion of Sewage Water into H2 Gas Fuel Using Hexagonal Nanosheets of the Polyaniline-Assisted Deposition of PbI2 as a Nanocomposite Photocathode with the Theoretical Qualitative Ab-Initio Calculation of the H2O Splitting

This study is very promising for providing a renewable enrgy (H₂ gas fuel) under the elctrochemical splitting of the wastwater (sewage water). This study has double benefits: hydrogen generation and contaminations removel. This study is carried out on sewage water, third stage treated, from Beni-Suef city, Egypt. Antimony tin oxide (ATO)/polyaniline (PANI)/PbI₂ photoelectrode is prepared through the in situ oxidative polymerization of PANI on ATO, then PANI is used as an assistant for PbI₂ deposition using the ionic adsorption deposition method. The chemical structural, morphological, electrical, and optical properties of the composite are confirmed using different analytical tools such as X-ray diffreaction (XRD), scanning electron microscope (SEM), transmision electron microscope (TEM), Fourier-transform infrared spectroscopy (FTIR), and UV-Vis spectroscopy. The prepared PbI₂ inside the composite has a crystal size of 33 nm (according to the peak at 12.8°) through the XRD analyses device. SEM and TEM confirm the hexagonal PbI₂ sheets embedded on the PANI nanopores surface. Moreover, the bandgap values are enhanced very much after the composite formation, in which the bandgap values for PANI and PANI/PbI₂ are 3 and 2.51 eV, respectively. The application of ATO/PANI/PbI₂ nanocomposite electrode for sewage splitting and H₂ generation is carried out through a three-electrode cell. The measurements carreid out using the electrocehical worksattion under th Xenon lamp (100 mW.cm⁻²). The produced current density (J_ph) is 0.095 mA.cm⁻² at 100 mW.cm⁻² light illumination. The photoelectrode has high reproducibility and stability, in which and the number of H₂ moles is 6 µmole.h⁻¹.cm⁻¹. The photoelectrode response to different monochromatic light, in which the produced J_ph decreases from 0.077 to 0.072 mA.cm⁻² with decreasing of the wavelengths from 390 to 636 nm, respectively. These values confirms the high response of the ATO/PANI/PbI₂ nanocomposite electrode for the light illuminaton and hydrogen genration under broad light region. The thermodynamic parameters: activation energy (Ea), enthalpy (ΔH*), and entropy (ΔS*) values are 7.33 kJ/mol, −4.7 kJ/mol, and 203.3 J/mol.K, respectively. The small values of ΔS* relted to the high sesnivity of the prepared elctrode for the water splitting and then the hydrogen gneration. Finally, a theoretical study was mentioned for calculation geometry, electrochemical, and thermochemistry properties of the polyaniline/PbI₂ nanocomposite as compared with that for the polyaniline.

Facile Fabrication of Polyaniline/Pbs Nanocomposite for High-Performance Supercapacitor Application

In this work, a polyaniline/lead sulfide (PANI/PbS) nanocomposite was prepared by combining the in situ oxidation polymerization method and the surface adsorption process. This nanocomposite was applied as a supercapacitor electrode. The crystal structure, nanomorphology, and optical analysis of PANI and PANI/PbS were investigated. The electrochemical performance of the designed PANI/PbS electrode-based supercapacitor was tested by using cyclic voltammetry (CV), chronopotentiometry (CP), and AC impedance techniques in HCl and Na2SO4 electrolytes. The average crystallite size of the PANI/PbS nanocomposite is about 43 nm. PANI/PbS possesses an agglomerated network related to PANI with additional spherical shapes from PbS nanoparticles. After the PANI/PbS nanocomposite formation, there are enhancements in their absorption intensities. At a current density of 0.4 A g-1, the specific capacitance of PANI/PbS in Na2SO4 and HCl was found to be 303 and 625 F g-1, respectively. In HCl (625 F g-1 and 1500 mF cm-2), the gravimetric and areal capacitances of the PANI/PbS electrode are nearly double those of the Na2SO4 electrolyte. Also, the average specific energy and specific power density values for the PANI/PbS electrode in HCl are 4.168 Wh kg-1 and 196.03 W kg-1, respectively. After 5000 cycles, the capacitance loses only 4.5% of its initial value. The results refer to the high stability and good performance of the designed PANI/PbS as a supercapacitor electrode.

Converting Sewage Water into H2 Fuel Gas Using Cu/CuO Nanoporous Photocatalytic Electrodes

This work reports on H2 fuel generation from sewage water using Cu/CuO nanoporous (NP) electrodes. This is a novel concept for converting contaminated water into H2 fuel. The preparation of Cu/CuO NP was achieved using a simple thermal combustion process of Cu metallic foil at 550 °C for 1 h. The Cu/CuO surface consists of island-like structures, with an inter-distance of 100 nm. Each island has a highly porous surface with a pore diameter of about 250 nm. X-ray diffraction (XRD) confirmed the formation of monoclinic Cu/CuO NP material with a crystallite size of 89 nm. The prepared Cu/CuO photoelectrode was applied for H2 generation from sewage water achieving an incident to photon conversion efficiency (IPCE) of 14.6%. Further, the effects of light intensity and wavelength on the photoelectrode performance were assessed. The current density (Jph) value increased from 2.17 to 4.7 mA·cm-2 upon raising the light power density from 50 to 100 mW·cm-2. Moreover, the enthalpy (ΔH*) and entropy (ΔS*) values of Cu/CuO electrode were determined as 9.519 KJ mol-1 and 180.4 JK-1·mol-1, respectively. The results obtained in the present study are very promising for solving the problem of energy in far regions by converting sewage water to H2 fuel.

Effect of Au Plasmonic Material on Poly M-Toluidine for Photoelectrochemical Hydrogen Generation from Sewage Water

This study provides H2 gas as a renewable energy source from sewage water splitting reaction using a PMT/Au photocathode. So, this study has a dual benefit for hydrogen generation; at the same time, it removes the contaminations of sewage water. The preparation of the PMT is carried out through the polymerization process from an acid medium. Then, the Au sputter was carried out using the sputter device under different times (1 and 2 min) for PMT/Au-1 min and PMT/Au-2min, respectively. The complete analyses confirm the chemical structure, such as XRD, FTIR, HNMR, SEM, and Vis-UV optical analyses. The prepared electrode PMT/Au is used for the hydrogen generation reaction using Na2S2O3 or sewage water as an electrolyte. The PMT crystalline size is 15 nm. The incident photon to current efficiency (IPCE) efficiency increases from 2.3 to 3.6% (at 390 nm), and the number of H2 moles increases from 8.4 to 33.1 mmol h−1 cm−2 for using Na2S2O3 and sewage water as electrolyte, respectively. Moreover, all the thermodynamic parameters, such as activation energy (Ea), enthalpy (ΔH*), and entropy (ΔS*), were calculated; additionally, a simple mechanism is mentioned for the water-splitting reaction.

Nanoporous TiN/TiO2/Alumina Membrane for Photoelectrochemical Hydrogen Production from Sewage Water

An aluminum oxide, Al2O3, template is prepared using a novel Ni imprinting method with high hexagonal pore accuracy and order. The pore diameter after the widening process is about 320 nm. TiO2 layer is deposited inside the template using atomic layer deposition (ALD) followed by the deposition of 6 nm TiN thin film over the TiO2 using a direct current (DC) sputtering unit. The prepared nanotubular TiN/TiO2/Al2O3 was fully characterized using different analytical tools such as X-ray diffraction (XRD), Energy-dispersive X-ray (EDX) spectroscopy, scanning electron microscopy (SEM), and optical UV-Vis spectroscopy. Exploring the current-voltage relationships under different light intensities, wavelengths, and temperatures was used to investigate the electrode's application before and after Au coating for H2 production from sewage water splitting without the use of any sacrificing agents. All thermodynamic parameters were determined, as well as quantum efficiency (QE) and incident photon to current conversion efficiency (IPCE). The QE was 0.25% and 0.34% at 400 mW·cm-2 for the photoelectrode before and after Au coating, respectively. Also, the activation energy was 27.22 and 18.84 kJ·mol-1, the enthalpy was 24.26 and 15.77 J·mol-1, and the entropy was 238.1 and 211.5 kJ-1·mol-1 before and after Au coating, respectively. Because of its high stability and low cost, the prepared photoelectrode may be suitable for industrial applications.