Effect of PbO-nanoparticles on dimethyl polysiloxane for use in radiation shielding applications

Enhanced radiation shielding efficiency of polystyrene nanocomposites with tailored lead oxide nanoparticles

In this study, we investigated a novel polymer nano-composite, PS-PbO, containing two distinct nano-sizes of lead oxide nanoparticles (PbO-A and PbO-B), in addition to the bulk size (PbO-K). These nanoparticles were embedded separately in a polystyrene (PS) matrix at different weight percentages (10%, 15%, 25%, and 35%) using roll mill mixing and compressing molding. Our evaluation focused on the radiation attenuation ability of PS-PbO and the effect of particle size, considering gamma-ray energies ranging from 0.06 to 1.3 MeV (from sources like 241Am, 133Ba, 137Cs, and 60Co). The linear attenuation coefficient (LAC) was determined by analyzing samples of the synthesized composite with different thicknesses. Then, various shielding parameters were calculated, including total molecular, atomic, and electronic cross-sections (σmol, σatm, σel), as well as the effective atomic number and the electron density (Zeff and Neff). Surprisingly, modifying PbO particle sizes had a significant impact on shielding efficiency. For instance, the composite with 25 wt% of the smallest PbO-B particles showed a 26.7% increase in LAC at 0.059 keV compared to the composite with 25 wt% of PbO-K (larger particles). Notably, the LAC peaked at low energy (0.059 keV), close to the K-edge of Pb, where interaction is directly proportional to Z4. With increasing PbO concentrations, the LAC of PS-PbO composites increased steadily. Additionally, as PbO concentration increased, the composite's effective atomic number Zeff and the electron density Neff increased, leading to a greater total Gamma-ray interaction cross-section. Furthermore, when comparing the Half-Value Layers of the novel nanocomposite to traditional lead shielding, a 70% reduction in mass was observed. Notably, the composite containing the smallest nano-size of PbO exhibited the highest radiation-shielding efficiency among all combinations and could therefore be used to create inexpensive and lightweight shields.

Novel composite based on silicone rubber and a nano mixture of SnO2, Bi2O3, and CdO for gamma radiation protection

Recently, there has been a surge of interest in the application of radiation-shielding materials. One promising research avenue involves using free-lead metal oxides/polymer composites, which have been studied for their radiation shielding and characterization properties. This study reinforced the dimethylpolysiloxane (silicone rubber) composites with micro- and nano-sized particles of tin oxide, cadmium oxide, and bismuth oxide as additive materials. The composites were tested with 20 and 50 weight fractions, and their attenuation coefficients were measured using a NaI(TI) detector at gamma-ray energies ranging from 59.54 to 1408.01 keV. Also, the thermal and mechanical properties of the composites were observed and compared with those of free silicone rubber. The results showed that the 50% nano metal oxide/SR composites exhibited better thermal stability and attenuation properties than the other composites, also possessing unique attributes such as lightweight composition and exceptional flexibility. Consequently, this composite material holds immense potential for safeguarding vital organs, including the eyes and gonads, during radiological diagnosis or treatment procedures. Its exceptional ability to absorb a significant portion of incident rays makes it an invaluable asset in the field of radiation protection.

Attenuation properties of poly methyl methacrylate reinforced with micro/nano ZrO2 as gamma-ray shields

This research aimed to examine the radiation shielding properties of unique polymer composites for medical and non-medical applications. For this purpose, polymer composites, based on poly methyl methacrylate (PMMA) as a matrix, were prepared and reinforced with micro- and nanoparticles of ZrO2 fillers at a loading of 15%, 30%, and 45% by weight. Using the high purity germanium (HPGe) detector, the suggested polymer composites' shielding characteristics were assessed for various radioactive sources. The experimental values of the mass attenuation coefficients (MAC) of the produced composites agreed closely with those obtained theoretically from the XCOM database. Different shielding parameters were estimated at a broad range of photon energies, including the linear attenuation coefficient (μ), tenth value layer (TVL), half value layer (HVL), mean free path (MFP), effective electron density (Neff), effective atomic number (Zeff), and equivalent atomic number (Zeq), as well as exposure buildup factor (EBF) and energy absorption buildup factor (EABF) to provide more shielding information about the penetration of γ-rays into the chosen composites. The results showed that increasing the content of micro and nano ZrO2 particles in the PMMA matrix increases μ values and decreases HVL, TVL, and MFP values. P-45nZ sample with 45 wt% of ZrO2 nanoparticles had the highest μ values, which varied between 2.6546 and 0.0991 cm-1 as γ-ray photon energy increased from 0.0595 to 1.408 MeV, respectively. Furthermore, the highest relative increase rate in μ values between nano and micro composites was 17.84%, achieved for the P-45nZ sample at 59.53 keV. These findings demonstrated that ZrO2 nanoparticles shield radiation more effectively than micro ZrO2 even at the same photon energy and filler wt%. Thus, the proposed nano ZrO2/PMMA composites can be used as effective shielding materials to lessen the transmitted radiation dose in radiation facilities.

EVA and SEBS-MA copolymers incorporated silicone rubber/SEBS blends: improvement of mechanical and thermal properties

Enhancing the mechanical and thermal properties of Silicone rubber (SR)/SEBS blends using various compatibilizers opens the opportunity for such new blends to meet the market desire. For this purpose, blends with a 1:1 ratio of SR and SEBS are prepared with different amounts of EVA or SEBS-MA copolymers as compatibilizer. Mechanical properties of the blend are enhanced by adding EVA and SEBS-MA. Addition of 6 phr EVA profoundly improves the tensile strength from 7.70 to 10.06 MPa. Thermogravimetric analysis reveals that the presence of compatibilizer can improve the thermal stability of the blend, especially its initial degradation temperature (T5%). T5% of the blend increases from 376 to 390 °C when comprising 6 phr SEBS-MA. Morphology of the blends is investigated using SEM and AFM. Results of the relaxation modulus curves obtained by rubber process analyzer (RPA) demonstrate that the amount of relaxation in the uncured blends is higher than the cured ones. A comparison of the relaxation of the blends indicates that the relaxation modulus of the SEBS-MA compatibilized blends is enhanced more than other blends after curing. Further investigations indicate that the compatibilized blends exhibit higher tear energy and lower compression set.

Impact of micro/nano cadmium oxide on shielding properties of cement-ball clay matrix

This study investigates the gamma radiation shielding properties of cement-ball clay matrix composites doped with micro- and nano-sized cadmium oxide (CdO) particles. The linear attenuation coefficient (LAC) was determined using a sodium iodide (NaI) detector and five radioactive point sources with energies ranging from 59.5 to 1408 keV. The LAC values obtained were compared to the XCOM database and found to be in good agreement. The composites' half-value layer (HVL), tenth value layer (TVL), mean free path (MFP), effective atomic number (Zeff), equivalent atomic number (Zeq), and absorption buildup factor (EABF) were determined. The results showed that the addition of CdO particles improved the radiation-shielding behavior of the composites and increasing the weight fraction of CdO particles increased the shielding effectiveness. The results also illustrated that when nano-sized CdO particles were compared to their micro-sized counterparts, there was a significant enhancement in radiation shielding effectiveness. For instance, a composite material composed of 50% cement, 41.7% ball clay, and 3.8% nano CdO at an energy level of 0.0595 MeV exhibited a remarkable 12.2% increase in attenuation, surpassing the performance of the micro-sized sample with an equivalent concentration. Similarly, another composite consisting of 50% cement, 33.3% ball clay, and 16.7% nano CdO demonstrated a significant 15.4% increase in attenuation at the same energy level, when compared to the micro-sized sample. The study demonstrates the potential of CdO-doped cement-ball clay matrix composites for gamma radiation shielding applications.

Novel slag/natural rubber composite as flexible material for protecting workers against radiation hazards

This work is an attempt to employ the electric arc furnace (EAF) slag as a by-product material to develop an alternative and environmentally friendly material for gamma-radiation protection applications such as in medical and industrial areas. For this purpose, different concentrations of micro-sized EAF slag (0, 20, 40, 60, 80, 100, 500, and 800 phr) were incorporated as fillers in the natural rubber (NR) matrix to produce the shielding composites. In addition, nano-sized EAF slag particles were prepared by using a high-energy ball milling technique to investigate the effect of particle size on the gamma-radiation shielding properties. The synthesized micro and nano EAF/NR composites were tested as protective materials against gamma-radiation by employing NaI(Tl) scintillation detector and standard radioactive point sources (152Eu, 137Cs, 133Ba, and 60Co). Different shielding parameters such as linear and mass attenuation coefficient, half value layer (HVL), tenth value layer, mean free path, effective atomic number (Zeff), and effective electron density (Neff) were determined to assess the radiation shielding capability of the EAF/NR composites. Furthermore, equivalent atomic number (Zeq) and the exposure buildup factor values for photon energy in the range from 0.015 to 15 MeV were also computed by Geometric Progression method. The experimental results of micro EAF/NR composites showed that at 121.78 keV, EAF0 composite (without EAF slag content) had the lowest μ value of 0.1695 cm-1, while the EAF800 composite (which was loaded with 800 phr of micro EAF slag) had the highest μ value of 0.2939 cm-1 at the same energy, which in turn decreases the HVL from 4.09 to 2.36 cm, respectively. Therefore, increasing the filler weight fractions of EAF slag in the NR matrix, increases the shielding properties of the composites. Moreover, the NR composite reinforced with 800 phr of nano EAF slag has better gamma-radiation shielding efficiency compared to that filled with 800 phr of micro EAF slag. The success of this work was to prepare a flexible, lightweight, low-cost, and lead-free material with better shielding capability.

Radiation attenuation properties of chemically prepared MgO nanoparticles/HDPE composites

Sheets of high-density polyethylene (HDPE) loaded with magnesium oxide in micro and nano were synthesized with different weight percentages of micro-MgO (0,5,10,20 and 30% by weight) and nano-MgO (5 and 30%) and shaped in form of disc and dog bone shape. The morphological, mechanical, and attenuation characteristics of each concentration were determined. The linear attenuation coefficients (LAC) of the prepared discs were calculated using a well-calibrated scintillation detector and five standard gamma-ray point sources (²⁴¹Am, ¹³³Ba, ¹³⁷Cs, ⁶⁰Co and ¹⁵²Eu). The LAC was theoretically calculated for HDPE/micro-MgO composites using XCOM software. A good agreement between the theoretical and experimental results was observed. The comparison between micro and nano-MgO as a filler in HDPE was evaluated. The results proved that the loaded nano-MgO in different proportions of HDPE produced greater attenuation coefficients than its micro counterpart. The addition of nano MgO with different weight percentage led to a significant improvement in the mechanical properties of HDPE, the ultimate force and ultimate stress increased as the concentration of nano MgO increased, and the young modulus of HDPE also increased with increasing concentration of micro and nano MgO.

Investigation on Physico Chemical and X-ray Shielding Performance of Zinc Doped Nano-WO3 Epoxy Composite for Light Weight Lead Free Aprons

This report addresses a way to reduce the usage of highly toxic lead in diagnostic X-ray shielding by developing a cost-effective, eco-friendly nano-tungsten trioxide (WO₃) epoxy composite for low-weight aprons. Zinc (Zn)-doped WO₃ nanoparticles of 20 to 400 nm were synthesized by an inexpensive and scalable chemical acid-precipitation method. The prepared nanoparticles were subjected to X-ray diffraction, Raman spectroscopy, UV-visible spectroscopy, photoluminescence, high-resolution-transmission electron microscope, scanning electron microscope, and the results showed that doping plays a critical role in influencing the physico-chemical properties. The prepared nanoparticles were used as shielding material in this study, which were dispersed in a non-water soluble durable epoxy resin polymer matrix and the dispersed materials were coated over a rexine cloth using the drop-casting method. The X-ray shielding performance was evaluated by estimating the linear attenuation coefficient (μ), mass attenuation coefficient (μ_m), half value layer (HVL), and X-ray percentage of attenuation. Overall, an improvement in X-ray attenuation in the range of 40-100 kVp was observed for the undoped WO₃ nanoparticles and Zn-doped WO₃ nanoparticles, which was nearly equal to lead oxide-based aprons (reference material). At 40 kVp, the percentage of attenuation of 2% Zn doped WO₃ was 97% which was better than that of other prepared aprons. This study proves that 2% Zn doped WO₃ epoxy composite yields a better particle size distribution, μ_m, and lower HVL value and hence it can be a convenient lead free X-ray shielding apron.

Investigation of Gamma-Ray Shielding Properties of Bismuth Oxide Nanoparticles with a Bentonite-Gypsum Matrix

Due to the present industrial world, the risk of radioactivity is notably increasing. Thus, an appropriate shielding material needs to be designed to protect humans and the environment against radiation. In view of this, the present study aims to design new composites of the main matrix of bentonite-gypsum with a low-cost, abundant, and natural matrix. This main matrix was intercalated in various amounts with micro- and nanosized particles of bismuth oxide (Bi₂O₃) as the filler. Energy dispersive X-ray analysis (EDX) recognized the chemical composition of the prepared specimen. The morphology of the bentonite-gypsum specimen was tested using scanning electron microscopy (SEM). The SEM images showed the uniformity and porosity of a cross-section of samples. The NaI (Tl) scintillation detector was used with four radioactive sources (²⁴¹Am, ¹³⁷Cs, ¹³³Ba, and ⁶⁰Co) of various photon energies. Genie 2000 software was used to determine the area under the peak of the energy spectrum observed in the presence and absence of each specimen. Then, the linear and mass attenuation coefficients were obtained. After comparing the experimental results of the mass attenuation coefficient with the theoretical values from XCOM software, it was found that the experimental results were valid. The radiation shielding parameters were computed, including the mass attenuation coefficients (MAC), half-value layer (HVL), tenth-value layer (TVL), and mean free path (MFP), which are dependent on the linear attenuation coefficient. In addition, the effective atomic number and buildup factors were calculated. The results of all of these parameters provided the same conclusion, which confirms the improvement of the properties of γ-ray shielding materials using a mixture of bentonite and gypsum as the main matrix, which is much better than using bentonite alone. Moreover, bentonite mixed with gypsum is a more economical means of production. Therefore, the investigated bentonite-gypsum materials have potential uses in applications such as gamma-ray shielding materials.

Gamma Attenuation Features of White Cement Mortars Reinforced by Micro/Nano Bi2O3 Particles

This study aims to explore the radiation protection properties of white mortars based on white cement as a binder and Bi₂O₃ micro and nanoparticles in proportions of 15 and 30% by weight as replacement sand. The average particle size of micro- and nano-Bi₂O₃ was measured using a transmission electron microscope (TEM). The cross-sectional morphology and distribution of Bi₂O3 within the samples can be obtained by scanning electron microscopy (SEM), showing that nanoscale Bi₂O₃ particles have a more homogeneous distribution within the samples than microscale Bi₂O₃ particles. The shielding parameters of the proposed mortars were measured using the HPGe detector at various γ-ray energies emitted by standard radioactive point sources ²⁴¹Am, ¹³³Ba, ⁶⁰Co, ¹³⁷Cs, and ¹⁵²Eu. The experimental values of the prepared mortars' mass attenuation coefficients (MAC) match well with those determined theoretically from the XCOM database. Other shielding parameters, including half value layer (HVL), tenth value layer (TVL), mean free path (MFP), effective electron density (N_eff), effective atomic number (Z_eff), equivalent atomic number (Z_eq), and exposure buildup factor (EBF), were also determined at different photon energies to provide more shielding information about the penetration of gamma radiation into the selected mortars. The obtained results indicated that the sample containing 30% by weight of nano Bi₂O₃ has the largest attenuation coefficient value. Furthermore, the results show that the sample with a high concentration of Bi₂O₃ has the highest equivalent atomic numbers and the lowest HVL, TVL, MFP, and EBF values. Finally, it can be concluded that Bi₂O₃ nanoparticles have higher efficiency and protection compared to microparticles, especially at lower gamma-ray energies.

Nano tin oxide/dimethyl polysiloxane reinforced composite as a flexible radiation protecting material

Reinforced polymer composites are a recent type of advanced shielding material that has been studied experimentally and theoretically. This work described the protection properties of silicon rubber filled with nano and micro tin oxide (II). These shielding materials are evaluated by parameters such as mass attenuation coefficient, linear attenuation coefficient, mean free path, effective atomic number, and buildup factor. The morphology and mechanical properties of silicon rubber, which is reinforced with tin oxide (II) particles in terms of weight fraction and size, have been studied. The results explain that the mass attenuation coefficient increases as tin oxide (II) concentration increases at a particular photon energy. It was found that the shielding properties of nano tin oxide (II) composites are more effective than micro tin oxide (II) composites against gamma rays. The effective atomic number values increase by increasing tin oxide (II) and so on equivalent atomic number. On the other hand, increasing tin oxide (II) weight fraction led to an increase in buildup factor maximum, which proved that tin oxide (II) concentration has significant effectiveness in radiation protection.