Plastic Deformation Modes of CuZr/Cu Multilayers

Precise determination of Young's modulus of amorphous CuZr/nanocrystalline Cu multilayer via nanoindentation

Extracting mechanical data of thin films on rigid substrates using nanoindentation is compromised by the mechanical properties of underlying substrates, which may falsify the obtained results. With ongoing miniaturization, the substrate influence becomes more pronounced. In this study we present an experimental approach to extract the true Young's modulus of crystalline-amorphous multilayers by means of nanoindentation. We used 1 µm thick multilayers comprised of amorphous CuZr and nanocrystalline Cu. All films were deposited onto two rigid substrate types with Young's moduli below and above the ones expected for the deposits (film-to-substrate hardness and elastic moduli ratios between 0.3 to 1.1 and 0.6 to 1.5, respectively). Linear extrapolation of indentation data to zero indentation depth allows to precisely determine the real film's Young's modulus. Same investigations were performed on monolithic Cu and CuZr films of same thickness. While the hardness values change with the variation of the bilayer thickness of the multilayer structures, the Young's modulus is not affected by the interfaces.

Graphical abstract

Crystalline-Amorphous Nanostructures: Microstructure, Property and Modelling

Crystalline metals generally exhibit good deformability but low strength and poor irradiation tolerance. Amorphous materials in general display poor deformability but high strength and good irradiation tolerance. Interestingly, refining characteristic size can enhance the flow strength of crystalline metals and the deformability of amorphous materials. Thus, crystalline-amorphous nanostructures can exhibit an enhanced strength and an improved plastic flow stability. In addition, high-density interfaces can trap radiation-induced defects and accommodate free volume fluctuation. In this article, we review crystalline-amorphous nanocomposites with characteristic microstructures including nanolaminates, core-shell microstructures, and crystalline/amorphous-based dual-phase nanocomposites. The focus is put on synthesis of characteristic microstructures, deformation behaviors, and multiscale materials modelling.

Highly Elastic and Conductive Metallic Interconnect with Crystalline-Amorphous Nanolaminate

Nanolaminate with alternating layers of nanocrystalline Cu and amorphous CuZrTi is suggested as highly stretchable and conductive interconnect material in stretchable devices. 50 nm nanocrystalline Cu and 20 nm amorphous CuZrTi are the optimum thicknesses of the constituent layers, which result in an elastic deformation limit of 3.33% similar to that of the monolithic amorphous CuZrTi film and an electrical conductivity of 11.83 S/μm corresponding to 70% of that of the monolithic nanocrystalline Cu film. The enhanced elastic deformability and conductivity of the nanolaminates enable the maintenance of the interconnect performance for cyclic stretching with a tensile strain of 114% in the form of a free-standing serpentine structure and a tensile strain of 30% in the form of an ordinary circular coil on an elastomer substrate.

Molecular Dynamics Study of the Nanoindentation Behavior of Cu64Zr36/Cu Amorphous/Crystalline Nanolaminate Composites

Amorphous/crystalline nanolaminate composites have aroused extensive research interest because of their high strength and good plasticity. In this paper, the nanoindentation behavior of Cu₆₄Zr₃₆/Cu amorphous/crystalline nanolaminates (ACNLs) is investigated by molecular dynamics (MD) simulation while giving special attention to the plastic processes occurring at the interface. The load–displacement curves of ACNLs reveal small fluctuations associated with shear transformation zone (STZ) activation in the amorphous layer, whereas larger fluctuations associated with dislocations emission occur in the crystalline layer. During loading, local STZ activation occurs and the number of STZs increases as the indentation depth in the amorphous layer increases. These STZs are mostly located around the indenter, which correlates to the high stresses concentrated around the indenter. When the indenter penetrates the crystalline layer, dislocations emit from the interface of amorphous/crystalline, and their number increases with increasing indentation depth. During unloading, the overall number of STZs and dislocations decreases, while other new STZs and dislocations become activated. These results are discussed in terms of stress distribution, residual stresses, indentation rate and indenter radius.

Anisotropic Phase Transformation in B2 Crystalline CuZr Alloy

B2 phase copper-zirconium (CuZr) particles are often used as an enhancement agent to improve the toughness of metallic glass; however, the orientation dependence of its phase transformation behaviors under loading remains unclear. In this work, molecular dynamics simulation of uniaxial tension and compression of B2 phase CuZr along different crystallographic orientation are performed to investigate the orientation-related mechanical response and phase transformation mechanisms. It was found that the mechanical behavior of CuZr exhibits obvious tension/compression asymmetry, but their failure mode is mainly local amorphization. Three different phase transformation behaviors, B2→FCC, B2→BCT, and B2→HCP, were observed in tension and compression along [001], and tension along [110], respectively. The transformations are realized by lattice rotation (~ 5°), uniform deformation and separation between Cu and Zr atomic layers, respectively. Before failure by local amorphization, phase transformation region can be recovered after unloading, showing the superelasticity.