Rational synthesis of methylsilsesquioxane aerogels addressing thermal load and compression recovery issues in Li-ion batteries

Li-ion batteries suffer from two key safety issues: thermal overload and compression recovery, which may lead to flammability and mechanical failure. Silica aerogels are promising solutions to both these issues owing to their excellent thermal stability and tailored mechanical properties. However, finding the optimum sol composition in sol-gel-based aerogel synthesis is needed to address these issues at industry-relevant scales. Here, we propose an innovative approach to determine the optimum sol composition for methylsilsesquioxane (MSQ) aerogel sheets, which is based on the mechanisms of the effects of molar ratios of hydrolysis water and isopropyl alcohol (IPA) to methyltrimethoxysilane (MTMS) on the physical properties of MSQ aerogel sheets and according to the ternary contour distribution of their properties. The synthesized MSQ aerogels exhibited a soft, light, and powderless texture and featured superhydrophobic properties (150.2°), low thermal conductivity of 33.6 mW/(m·K), high thermal stability temperature in nitrogen atmosphere at 479.3 °C and moderate short-term (<6 h) service temperature of 120.0 °C. Significantly, the structural stability and elasticity of the aerogels surpassed the current state-of-the-art, showing recovery to 81.3 % of the original thickness and 85.2 % of the original stress after being subjected to 400 cycles of high-speed and high-strain consecutive compression, respectively. These excellent properties make the MSQ aerogel sheets promising for applications in thermal load and compression recovery management of diverse energy storage devices, including batteries for next-generation electric vehicles.

A 3D Hierarchical Host with Gradient-Distributed Dielectric Properties toward Dendrite-free Lithium Metal Anode

The conventional conductive three-dimensional (3D) host fails to effectively stabilize lithium metal anodes (LMAs) due to the internal incongruity arising from nonuniform lithium-ion gradient and uniform electric fields. This results in undesirable Li "top-growth" behavior and dendritic Li growth, significantly impeding the practical application of LMAs. Herein, we construct a 3D hierarchical host with gradient-distributed dielectric properties (GDD-CH) that effectively regulate Li-ion diffusion and deposition behavior. It comprises a 3D carbon fiber host modified by layer-by-layer bottom-up attenuating Sb particles, which could promote Li-ion homogeneously distribution and reduce ion concentration gradient via unique gradient dielectric polarization. Sb transforms into superionic conductive Li3Sb alloy during cycling, facilitating Li-ion dredging and pumps towards the bottom, dominating a bottom-up deposition regime confirmed by COMSOL Multiphysics simulations and physicochemical characterizations. Consequently, a stable cycling performance of symmetrical cells over 2000 h under a high current density of 10 mA cm-2 is achieved. The GDD-CH-based lithium metal battery shows remarkable cycling stability and ultra-high energy density of 378 Wh kg-1 with a low N/P ratio (1.51). This strategy of dielectric gradient design broadens the perspective for regulating the Li deposition mechanism and paves the way for developing high-energy-density lithium metal anodes with long durability.

Flexible and Compressible Nanostructure-Assembled Aramid Nanofiber/Silica Composites Aerogel

The Applications of silica aerogel are limited due to its brittleness and low strength. As a result, it is essential to strengthen and toughen it. Organic nanofibers are one of the preferred reinforcement materials. In this work, we designed and fabricated flexible and compressible nanostructure-assembled aramid nanofiber/silica composites aerogel (ANF/SiO2 aerogel) to improve the mechanical strength and flexibility of silica aerogel without compromising thermal insulation properties. The aramid nanofiber/silica composite aerogels were prepared by immersing the aramid nanofiber wet gel into the silica sol for a certain period of time followed by freeze drying without solvent replacement. The surface modifier 3-aminopropyltriethoxysilane (APTES) was used as a coupling agent to form chemical linkage between the ANF fiber and silica gel. It was observed that APTES can effectively drive the silica sol to infuse into ANF hydrogel, promoting the assembly of silica gel onto the fiber surface and a uniform distribution in the network of ANF. The compressive resilience, thermal stability, and thermal insulation properties of the composite aerogels were evaluated by inducing the silica aerogel into the ANF network to form a protective layer on the fiber and change the pore structure in the ANF network.

Solution Combustion Synthesis of High-Performance Nano-LiFePO4/C Cathode Material from Cost-Effective Mixed Fuels

Solution combustion synthesis (SCS) is considered as an efficient and energy-saving method for preparing LiFePO4/C composite material with the nanostructure (Nano-LiFePO4/C). In this study, Nano-LiFePO4/C cathode material was prepared using SCS using a cost-effective combination of urea and sorbitol as mixed fuels. The effect of mixed fuels on combustion behavior and microstructure as well as on electrochemical performance was studied using XRD, BET, SEM, TEM, and electrochemical characterization methods. Multiple characterization results indicated that the maximum temperature (Tm) and particle size were influenced by the usage of urea and sorbitol. The sample derived under optimum conditions exhibits a mesoporous nanostructure with a large surface specific area and attractive electrochemical performance with a discharge capacity of 153.5 mAh/g at 0.1 C, which shows strong potential for commercial applications in the future.

Heat-Treated Aramid Pulp/Silica Aerogel Composites with Improved Thermal Stability and Thermal Insulation

In this work, we prepared heat-treated aramid pulp/silica aerogel composites (AP/aerogels) and investigated in detail the feasibility of improving thermal stability and thermal insulation via tailored heat treatment. The microstructure and FTIR spectra reveal that AP/aerogels are formed by a physical combination of the silica aerogel matrix and aramid pulps. When the heat treatment temperature increases, the density slightly decreases and then increases to the maximum due to the significant volume shrinkage. The pyrolysis of aramid pulp and the collapse of silica skeletons occur during heat treatment; nevertheless, the typical structures of AP/aerogels do not change significantly. It is also found that both the hydrophobicity and the thermal insulation decrease with the increasing heat treatment temperature. We note that when the heat treatment is at 600 °C, the AP/aerogel still maintains a low density of 0.19 g/cm3 and a contact angle of 138.5°. The thermal conductivity is as low as 26.11 mW/m/K, measured using the transient hot wire method. Furthermore, the heat-treated AP/aerogels can avoid heat shock and possible thermal hazards during practical thermal insulation applications. The onset temperatures of the thermal decomposition of AP/aerogels increase from 298.8 °C for an untreated one to 414.7 °C for one treated at 600 °C, indicating that the thermal stability of AP/aerogels is improved significantly. This work provides a practical engineering approach to expand the thermal insulation applications of silica aerogel composites.

The Anatomy of Amorphous, Heterogeneous Catalyst Pellets

This review focuses on disordered, or amorphous, porous heterogeneous catalysts, especially those in the forms of pellets and monoliths. It considers the structural characterisation and representation of the void space of these porous media. It discusses the latest developments in the determination of key void space descriptors, such as porosity, pore size, and tortuosity. In particular, it discusses the contributions that can be made by various imaging modalities in both direct and indirect characterisations and their limitations. The second part of the review considers the various types of representations of the void space of porous catalysts. It was found that these come in three main types, which are dependent on the level of idealisation of the representation and the final purpose of the model. It was found that the limitations on the resolution and field of view for direct imaging methods mean that hybrid methods, combined with indirect porosimetry methods that can bridge the many length scales of structural heterogeneity and provide more statistically representative parameters, deliver the best basis for model construction for understanding mass transport in highly heterogeneous media.

In-Situ Synthesis of Layered Double Hydroxide/Silica Aerogel Composite and Its Thermal Safety Characteristics

To adjust the thermal safety of hydrophobic silica aerogel, layered double hydroxide (LDH)/silica aerogel (SA) composites were prepared by an in-situ sol-gel process at ambient pressure. This study found the physical combination of SA and MgAl-LDH based on the FTIR spectra and phase composition of LDH/SA. The N2 sorption analysis confirms that the introduction of MgAl-LDH does not change the mesoporous attribution of LDH/SA significantly. With the increase in MgAl-LDH addictive content, the low density (0.12–0.13 g/cm3), low thermal conductivity (24.28–26.38 mW/m/K), and large specific surface area (730.7–903.7 m2g) of LDH/SA are still maintained, which can satisfy the requirements of thermal insulation. The TG-DSC analysis demonstrates that the endothermic effects and metal oxides formed during the MgAl-LDH decomposition are beneficial to the improvement of the thermal stability of LDH/SA composites. In addition, it was found that the gross calorific values of LDH/SA composites decrease with an increase in MgAl-LDH addictive content, all of which are lower than that of the pure SA. The research outcomes indicate that the thermal safety of LDH/SA composites is enhanced significantly by doping MgAl-LDH without impairing too many of the excellent properties, which benefits their expansion in the thermal insulation field.

Lower coordination Co3O4 mesoporous hierarchical microspheres for comprehensive sensitization of triethylamine vapor sensor

Monitoring and detecting triethylamine (TEA) vapor are essential in the organic synthesis industry. Two-dimensional Co₃O₄ nanosheets with large surface areas and multiple active sites are ideal for fabricating chemiresistive gas sensors. However, the face-to-face stacking owing to the high surface energy of nanosheets, would cover up the active sites, obstruct gas diffusion, raise contact resistance, which all hinder its utilization for TEA detection. Herein, the Co₃O₄ mesoporous nanosheets were assembled into hierarchical microspheres by adding the structure-directing agent PVP K30 and combined with a proper annealing temperature, which optimized their grain size, specific surface area, pores structure, oxygen vacancies, and the atomic ratio of Co²⁺ to Co³⁺. And these ultimately improved the detection capability of TEA. The sensor based on Co₃O₄ sphere-300 exhibits the highest sensor response of 34.1-100 ppm TEA and a low detection limit (0.5 ppm) at a low working temperature of 150 °C. The promising properties are mainly due to the combination of several advantages that facilitate simultaneous chemical and electronic sensitization. This work prepared a high-performance TEA gas sensor and verified the improvement of comprehensive sensitization on the gas-sensing performance of two-dimensional metal oxide semiconductors.

Polymeric Network Hierarchically Organized on Carbon Nano-onions: Block Polymerization as a Tool for the Controlled Formation of Specific Pore Diameters

The organization of specific pores in carbonaceous three-dimensional networks is crucial for efficient electrocatalytic processes and electrochemical performance. Therefore, the synthesis of porous materials with ordered and well-defined pores is required in this field. The incorporation of carbon nanostructures into polymers can create material structures that are more ordered in comparison to those of the pristine polymers. In this study we applied polymer-templated methods of carbon material preparation, in which outer blocks of the star copolymers form the carbon skeleton, while the core part is pore-forming. Well-defined 6-star-(poly(methyl acrylate)-b-poly(4-acetoxystyrene)) dendrimers were synthesized by reversible addition-fragmentation chain-transfer polymerization. They were then transformed into poly(4-vinylphenol) derivatives (namely 6-star-(poly(methyl acrylate)-b-poly(4-vinylphenol)), subjected to polycondensation with formaldehyde, and pyrolyzed at 800 °C. Cross-linking of phenolic groups provides a polymer network that does not depolymerize by pyrolysis, unlike poly(methyl acrylate) chains. The selected star polymers were attached to carbon nano-onions (CNOs) to improve the organization of the polymer chains. Herein, the physicochemical properties of CNO-polymer hybrids, including the textural and the electrochemical properties, were compared with those of the pristine pyrolyzed polymers obtained under analogous experimental conditions. For these purposes, we used several experimental and theoretical methods, such as infrared, Raman, and X-ray photoelectron spectroscopy, nitrogen adsorption/desorption measurements, scanning and transmission electron microscopy, and electrochemical studies, including cyclic voltammetry. All of the porous materials were evaluated for use as supercapacitors.

One-Pot Method to Synthesize Silver Nanoparticle-Modified Bamboo-Based Carbon Aerogels for Formaldehyde Removal

The present study demonstrated a freeze-drying-carbonization method to synthesize silver nanoparticle-modified bamboo-based carbon aerogels to remove formaldehyde. The bamboo-based carbon aerogel (BCA) has the advantages of controllable pore size and rich oxygen-containing groups, which can provide a good foundation for surface modification. BCA can greatly enhance the purification of formaldehyde by loading silver nanoparticles. The maximum adsorption capacity of 5% Ag/BCA for formaldehyde reached 42 mg/g under 25 ppm formaldehyde concentration, which is 5.25 times more than that of BCA. The relevant data were fitted by the Langmuir model and the pseudo 2nd-order model and good results were obtained, indicating that chemical absorption occurred between the carbonyl of formaldehyde and the hydroxyl of BCA. Therefore, silver nanoparticle-modified bamboo-based carbon aerogels play a positive role in the selective removal of formaldehyde. Silver nanoparticles promoted the activation of oxygen and strengthened the effect of BCA on HCHO adsorption.

Directionally Tailoring Macroporous Honeycomb-Like Structured Carbon Nanofibers toward High-Capacitive Potassium Storage

Constructing high-capacitive potassium storage materials can avoid the sluggish and unstable bulk diffusion process via a surface-induced process, which is conducive to swift and frequent potassium storage. Herein, we demonstrated the use of macroporous honeycomb-like carbon nanofibers (MHCNFs) as an excellent anode material for high-capacitive potassium storage. The as-made MHCNFs feature abundant well-controlled macropores, an amorphous structure, and a large specific surface area of around 595.9 m² g^-1. These structural characteristics could significantly reduce the transferring distance of electrons/ions, offer abundant active sites, enable high-capacitive contribution, and thus substantially improve the kinetics and structural stability of MHCNFs. Experimental investigation demonstrated that MHCNFs enable ultrahigh potassium storage ability (329.1 mAh g^-1 at 100 mA g^-1) and competitive rate capability (168.5 mAh g^-1 at 5000 mA g^-1). More impressively, even when cycled at 1000 mA g^-1, the robust structure of MHCNFs can still enable the electrodes a capacity of 252.6 mAh g^-1 over repeating 2500 cycles. This work offers a promising strategy that macropore engineering coupled with amorphous structure can make effectively elevated K⁺ diffusion kinetic performance and promoted K⁺ adsorption/intercalation storage possible.

Waffle-Like Carbons Combined with Enriched Mesopores and Highly Heteroatom-Doped Derived from Sandwiched MOF/LDH/MOF for High-Rate Supercapacitor

Supercapacitors (SCs) are promising for powering mobile devices, electric vehicles and smart power grids due to their fast charge/discharge rate, high power capability and robust cycle stability. Nitrogen-doped porous carbons are great alternatives because they provide pseudocapacitance without losing their power rate. Nanoporous carbon derived from metal organic frameworks (MOFs) is an ideal precursor for preparing heteroatom-doped carbons due to their abundant nitrogen contents and incredible specific surface areas. However, severe aggregations and the leakage of nitrogen can occur during harsh carbonization. In this study, we used CoAl-LDH (cobalt aluminum layered double hydroxide) as an in-situ growth substrate, allowing Co-based MOF to uniformly grow onto the CoAl-LDH to form a sandwiched MOF/LDH/MOF structure. After acid etching, we obtained waffle-like nanoporous carbons (WNPC). WNPC exhibited high nitrogen and oxygen retention (7.5 wt% and 9.1 wt%) and a broad mesopores distribution with specific surface areas of 594 m²g⁻¹, which promoted a sieving effect. This renders a specific capacitance of 300.7 F·g⁻¹ at 1 A·g⁻¹ and the high retention (72%) of capacitance at 20 A·g⁻¹, ensuring its use at high-rate supercapacitor electrodes. Finally, the WNPC symmetric supercapacitor reaches a superior specific energy of 27 W·h·kg⁻¹ at a power of 500 W·kg⁻¹, and a good cycle stability (85% capacitance retention after 10,000 cycles).

Electrorheological Properties of Polydimethylsiloxane/TiO2-Based Composite Elastomers

Electrorheological elastomers based on polydimethylsiloxane filled with hydrated titanium dioxide with a particle size of 100-200 nm were obtained by polymerization of the elastomeric matrix, either in the presence, or in the absence, of an external electric field. The viscoelastic and dielectric properties of the obtained elastomers were compared. Analysis of the storage modulus and loss modulus of the filled elastomers made it possible to reveal the influence of the electric field on the Payne effect in electrorheological elastomers. The elastomer vulcanized in the electric field showed high values of electrorheological sensitivity, 250% for storage modulus and 1100% for loss modulus. It was shown, for the first time, that vulcanization of filled elastomers in the electric field leads to a significant decrease in the degree of crosslinking in the elastomer. This effect should be taken into account in the design of electroactive elastomeric materials.

Evaluation of photocatalytic selectivity of Ag/Zn modified molecularly imprinted TiO2 by multiwavelength measurement

In this paper, Ag/Zn-MIP-TiO₂ was prepared by sol-gel method, and the imprinted molecule was ethyl p-hydroxybenzoate. To study the properties of the Ag/Zn-MIP-TiO₂ on the photocatalytic activity, these factors were investigated: the effects of the dosage of Ag and Zn, the amount of imprinted molecules, the calcination temperature and time, then the capture of active substances. Besides, the selectivity of Ag/Zn-MIP-TiO₂ was investigated in three aspects: UV-vis multi-wavelength spectral integral area change, specific group absorbance change and traditional reaction kinetic parameter change. The selectivity coefficients of the three angles are 8.55, 1.47 and 6.77. And the selectivity factors are 4.12, 1.02 and 4.81, indicating that Ag/Zn-MIP-TiO₂ has high selectivity. Furthermore, its selectivity is not only for the specific characteristic groups on the target pollutants, but for the integrated target pollutants. From the perspective of materials, Ag/Zn-MIP-TiO₂ is 100% anatase with a lower band gap and a larger specific surface area. As a molecularly imprinted polymer, the active sites on the surface make it have selective recognition function. The results of photocatalytic experiments are as follows: the optimum Ag and Zn ratio is Ti:Ag:Zn = 100:1:0.75 (molar ratio); the best molecular weight of imprint is Ti:MIP = 5:1; the finest calcination temperature is 500 °C; the optimum calcination time is 2 h; the removal rate of ethyl p-hydroxybenzoate degraded by photocatalysis for 2 h is 99.1%; the main active substance of the photocatalytic reaction is •OH.

Multifunctional flexible membranes from sponge-like porous carbon nanofibers with high conductivity

Conductive porous carbon nanofibers are promising for environmental, energy, and catalysis applications. However, increasing their porosity and conductivity simultaneously remains challenging. Here we report chemical crosslinking electrospinning, a macro-micro dual-phase separation method, to synthesize continuous porous carbon nanofibers with ultrahigh porosity of >80% and outstanding conductivity of 980 S cm-1. With boric acid as the crosslinking agent, poly(tetrafluoroethylene) and poly(vinyl alcohol) are crosslinked together to form water-sol webs, which are then electrospun into fibrous films. After oxidation and pyrolysis, the as-spun fibers are converted into B-F-N triply doped porous carbon nanofibers with well-controlled macro-meso-micro pores and large surface areas of ~750 m2 g-1. The sponge-like porous carbon nanofibers with substantially reduced mass transfer resistances exhibit multifunction in terms of gas adsorption, sewage disposal, liquid storage, supercapacitors, and batteries. The reported approach allows green synthesis of high-performance porous carbon nanofibers as a new platform material for numerous applications.

Retention loss of reversed-phase chromatographic columns using 100% aqueous mobile phases from fundamental insights to best practice

This work deals with experimental investigations pertaining to the impact of chemical (electrolyte concentration from 0 to 100 mM, dissolved nitrogen gas from 0 to 6.7  ×  10^-4 M in water; surface chemistry including hexylphenyl, polyphenyl, C₃₀, C₁₈, and C₈; surface coverage in C₁₈-bonded chains from 1.5 to 3.5 µmol/m²; presence of surface dopant), physical (hydrostatic pressure of water from 50 to 500 bar; temperature from 27 ^∘C to 75 ^∘C), and structural parameters (average pore size from 50 Å to 400 Å; pore connectivity) on the dewetting kinetics of water from the hydrophobic mesopores of particles packed in RPLC columns. The results are explained from physico-chemical viewpoints involving intrusion and extrusion Laplace pressures, advancing and receding contact angles, surface tension of water, vapor pressure of water, 3D reconstruction of the actual mesoporous structure, pore connectivity, and the hysteresis in nitrogen adsorption and desorption isotherm onto reversed-phase chromatographic materials. A model of water dewetting consistent with the observations and the physical interpretations is then proposed. Finally, the most relevant practical solutions (pressurizing the column in absence of flow, pore size enlargement, using phenyl-bonded phase, polar embedded or surface doped C₁₈-bonded phases, reducing the C₁₈ surface coverage, doping the silica surface, lengthening of the alkyl-bonded chains, applying low temperatures, purging and degassing the mobile phase with helium gas) are suggested in order to eliminate or at least minimize the retention loss of RPLC columns when using fully aqueous mobile phases.

Kinetic mechanism of water dewetting from hydrophobic stationary phases utilized in liquid chromatography

An experimental protocol was designed to accurately measure the dewetting kinetics of aqueous mobile phases from reversed-phase liquid chromatography (RPLC) columns. The protocol enables the determination of the losses in the wetted surface area and internal pore volume (leading to undesirable retention losses) of RPLC columns as a function of the dewetting time. It is used to evaluate the impact of the buffer/salt concentration in water (0-100 mM), nitrogen concentration dissolved in water (0-6.7 × 10^-4 M), column temperature (300-358 K), and of the internal structure (pore connectivity) of the stationary phase on the dewetting kinetics of various RPLC packing materials. From a fundamental viewpoint, the experimental facts demonstrate that dewetting kinetics are not solely driven by the pore size of the stationary phase and the contact angle with water. Temperature has a major influence on dewetting kinetics as it controls the nucleation rate of isolated water vapor bubbles over the entire mesoporous network. Additionally, the internal microstructure of the stationary phase (characterized by its internal porosity, pore size distribution, and pore connectivity) influences the rate at which the water vapor bubbles grow and coalesce in the entire particle volume. From a more practical viewpoint, the retention loss of RPLC columns due to water dewetting can be eliminated or at least minimized by (1) adjusting the surface and bonding chemistries to reduce the receding contact angle, (2) elevating the column outlet pressure, (3) operating at the lowest possible temperature, (4) minimizing the pore connectivity of the stationary phase (e.g., by increasing the degree of surface functionalization from C₈ to C₁₈-bonded phases), and (5) by degassing the aqueous mobile phase from any dissolved gases.

Fabrication of Cobalt-Nickel-Zinc Ternary Oxide Nanosheet and Applications for Supercapacitor Electrode

Mesoporous cobalt-nickel-zinc ternary oxide (CNZO) nanosheets grown on the nickel foam are prepared by a simple hydrothermal treatment and subsequent calcination process. The physical characterizations show that the as-obtained CNZO nanosheets possess the mesoporous structure and a high specific surface of 75.4 m² g^-1 has been achieved. When directly applied for the binder-free supercapacitor electrode for the first time, the nickel foam supported mesoporous CNZO nanosheet electrode exhibits an ultrahigh specific capacity about 1172.2 C g^-1 at 1 A g^-1. More significantly, an asymmetric supercapacitor based on the as-obtained CNZO positive electrode and an activated carbon negative electrode shows a high energy density of 84.2 Wh kg^-1 at a power density of 374.8 W kg^-1, with excellent cycle stability (keeps 78.8% capacitance retention and 100% coulombic efficiency after 2,500 cycles). The excellent supercapacitive properties suggest that the nickel foam supported CNZO nanosheet electrodes are promising for application as high-performance supercapacitor.

Polystyrene Opals Responsive to Methanol Vapors

Photonic crystals (PCs) show reflectance spectra depending on the geometrical structure of the crystal, the refractive index (neff), and the light incident angle, according to the Bragg-Snell law. Three-dimensional photonic crystals (3D-PCs) composed of polymeric sub-micrometer spheres, are arranged in an ordered face cubic centered (fcc) lattice and are good candidates for vapor sensing by exploiting changes of the reflectance spectra. We synthesized high quality polystyrene (PS) 3D-PCs, commonly called opals, with a filling factor f near to the ideal value of 0.74 and tested their optical response in the presence of different concentrations of methanol (MeOH) vapor. When methanol was present in the voids of the photonic crystals, the reflectance spectra experienced energy shifts. The concentration of methyl alcohol vapor can be inferred, due to a linear dependence of the reflectance band maximum wavelength as a function of the vapor concentration. We tested the reversibility of the process and the time stability of the system. A limit of detection (LOD) equal to 5% (v/v₀), where v was the volume of methanol and v₀ was the total volume of the solution (methanol and water), was estimated. A model related to capillary condensation for intermediate and high methanol concentrations was discussed. Moreover, a swelling process of the PS spheres was invoked to fully understand the unexpected energy shift found for very high methanol content.

Probing the Catalytic Efficiency of Supported Heteropoly Acids for Esterification: Effect of Weak Catalyst Support Interactions

Supported heteropoly acids are an interesting class of solid acid catalysts which possess flexible structure and super acidic properties essentially required for the oil-based biodiesel production. In this study, a series of catalysts containing 25 wt.% of heteropolytungstate (HPW) supported on various clays or SiO2 were prepared, and their catalytic efficiency was evaluated for esterification of acetic acid with heptanol. The as-prepared catalysts were characterized by various techniques including FT-IR spectroscopy, thermogravimetric analysis, X-ray diffraction, scanning electron microscopy, and BET. The catalytic efficiency of both bulk and supported HPW catalysts for the esterification activity strongly depends on the type of support and amount of catalyst; the bulk HPW catalyst and the catalyst supported by kaolinite with 25 wt.% of HPW exhibited highest activity. In order to study the effect of temperature on conversion, all the catalysts were subjected to different reaction temperatures. It was revealed that esterification activity of both bulk and supported HPW catalysts strongly depends upon the temperature variations of the reaction. Besides, the effect of leaching of active sites on the catalysts performance for biodiesel production was also evaluated by inductively coupled plasma studies (ICP). The kaolinite-supported catalyst (25% HPW/kaolinite) demonstrated higher amount of leaching which is also confirmed by the significant decrease in its catalytic activity when it is used for the second time. However, the higher activity demonstrated by HPW/kaolinite maybe because of some homogeneous reaction indicating a weak catalyst support interaction (WCSI) resulting in the leaching of the catalyst during the test. Furthermore, the effects of other reaction variables such as catalyst loading and reaction time on the conversion of acetic acid were also studied.

Assembling Ultrasmall Copper-Doped Ruthenium Oxide Nanocrystals into Hollow Porous Polyhedra: Highly Robust Electrocatalysts for Oxygen Evolution in Acidic Media

Here, a facile and novel strategy for the preparation of Cu-doped RuO2 hollow porous polyhedra composed of ultrasmall nanocrystals through one-step annealing of a Ru-exchanged Cu-BTC derivative is reported. Owing to the optimized surface configuration and altered electronic structure, the prepared catalyst displays a remarkable oxygen evolution reaction (OER) performance with low overpotential of 188 mV at 10 mA cm-2 in acidic electrolyte, an ultralow Tafel slope of 43.96 mV dec-1 , and excellent stability in durability testing for 10 000 cycles, and continuous testing of 8 h at a current density of 10 mA cm-2 . Density functional theory calculations reveal that the highly unsaturated Ru sites on the high-index facets can be oxidized gradually and reduce the energy barrier of rate-determining steps. On the other hand, the Cu dopants can alter the electronic structures so as to further improve the intrinsic OER activity.

A type of thiophene-bridged silica aerogel with a high adsorption capacity for organic solvents and oil pollutants

Thiophene-bridged silica aerogel was prepared from tetraethyl orthosilicate (TEOS) and 2,5-divinyltrimethoxysilanethiophene (DVTHP) through a facile sol–gel reaction and ambient pressure drying process.

Adsorption of diclofenac on a magnetic adsorbent based on maghemite: experimental and theoretical studies

Maghemite nanoparticles synthesized by one-pot synthesis adsorb diclofenac efficiently.

Ruthenium-cobalt nanoalloys encapsulated in nitrogen-doped graphene as active electrocatalysts for producing hydrogen in alkaline media

The scalable production of hydrogen could conveniently be realized by alkaline water electrolysis. Currently, the major challenge confronting hydrogen evolution reaction (HER) is lacking inexpensive alternatives to platinum-based electrocatalysts. Here we report a high-efficient and stable electrocatalyst composed of ruthenium and cobalt bimetallic nanoalloy encapsulated in nitrogen-doped graphene layers. The catalysts display remarkable performance with low overpotentials of only 28 and 218 mV at 10 and 100 mA cm⁻², respectively, and excellent stability of 10,000 cycles. Ruthenium is the cheapest platinum-group metal and its amount in the catalyst is only 3.58 wt.%, showing the catalyst high activity at a very competitive price. Density functional theory calculations reveal that the introduction of ruthenium atoms into cobalt core can improve the efficiency of electron transfer from alloy core to graphene shell, beneficial for enhancing carbon–hydrogen bond, thereby lowing ΔG_H* of HER.

Ruthenium is the cheapest platinum-group metal, yet active hydrogen evolution catalysts with low amounts of ruthenium have yet to be designed. Here, the authors report the preparation of a ruthenium–cobalt nanoalloy and demonstrate its potential as an effective hydrogen evolution catalyst in basic media.

Fabrication of calix[4]arene-attached mesoporous ammonium molybdophosphate–silica hybrid and its application as an adsorbent for cesium ions

The cesium cation is a common contaminant in medical and industrial products as well as in nuclear wastes, and it can present a serious risk to human health.

Recent advances in the textural characterization of hierarchically structured nanoporous materials

This review focuses on important aspects of applying physisorption for the pore structural characterization of hierarchical materials such as mesoporous zeolites.

Nanoforest of hierarchical core/shell CuO@NiCo2O4 nanowire heterostructure arrays on nickel foam for high-performance supercapacitors

Nickel foam-supported hierarchical core/shell CuO@NiCo₂O₄ nanowire heterostructure arrays with excellent supercapacitive performance are reported.

Hierarchical Mesoporous Zinc-Nickel-Cobalt Ternary Oxide Nanowire Arrays on Nickel Foam as High-Performance Electrodes for Supercapacitors

Nickel foam supported hierarchical mesoporous Zn-Ni-Co ternary oxide (ZNCO) nanowire arrays are synthesized by a simple two-step approach including a hydrothermal method and subsequent calcination process and directly utilized for supercapacitive investigation for the first time. The nickel foam supported hierarchical mesoporous ZNCO nanowire arrays possess an ultrahigh specific capacitance value of 2481.8 F g(-1) at 1 A g(-1) and excellent rate capability of about 91.9% capacitance retention at 5 A g(-1). More importantly, an asymmetric supercapacitor with a high energy density (35.6 Wh kg(-1)) and remarkable cycle stability performance (94% capacitance retention over 3000 cycles) is assembled successfully by employing the ZNCO electrode as positive electrode and activated carbon as negative electrode. The remarkable electrochemical behaviors demonstrate that the nickel foam supported hierarchical mesoporous ZNCO nanowire array electrodes are highly desirable for application as advanced supercapacitor electrodes.

Oxidation of Cyclohexene over Mesoporous Silica Pillared Clay Incorporated with Heteropoly Acid Prepared by Sol Gel Method

Mesoporous silica pillared clay (SPC) materials with different contents of H4PMo11VO40 (PVMo) heteropoly acid were synthesized by introducingPVMo into clay interlayer template in an acidic suspension using sol–gel method. The results of the characterizations showed that PVMo was dispersed homogeneously in the encapsulated samples. The encapsulated materials exhibited good catalytic performance in oxidation of cyclohexene.