The Detection of Trace Metal Contaminants in Organic Products Using Ion Current Rectifying Quartz Nanopipettes

While ion current rectification (ICR) in aprotic solvent has been fundamentally studied, its application in sensing devices lacks exploration. The development of sensors operable in these solvents is highly beneficial to the chemical industry, where polar aprotic solvents, such as acetonitrile, are widely used. Currently, this industry relies on the use of inductively coupled plasma mass spectrometry (ICP-MS) and optical emission spectroscopy (OES) for the detection of metal contamination in organic products. Herein, we present the detection of trace amounts of Pd2+ and Co2+ using ion current rectification, in cyclam-functionalized quartz nanopipettes, with tetraethylammonium tetrafluoroborate (TEATFB) in MeCN as supporting electrolyte. This methodology is employed to determine the concentration of Pd in organic products, before and after purification by Celite filtration and column chromatography, obtaining comparable results to ICP-MS within minutes and without complex sample preparation. Finite element simulations are used to support our experimental findings, which reveal that the formation of double-junction diodes in the nanopore enables trace detection of these metals, with a significant response from baseline even at picomolar concentrations.

Metal-organic frameworks as O2-selective adsorbents for air separations

Oxygen is a critical gas in numerous industries and is produced globally on a gigatonne scale, primarily through energy-intensive cryogenic distillation of air. The realization of large-scale adsorption-based air separations could enable a significant reduction in associated worldwide energy consumption and would constitute an important component of broader efforts to combat climate change. Certain small-scale air separations are carried out using N2-selective adsorbents, although the low capacities, poor selectivities, and high regeneration energies associated with these materials limit the extent of their usage. In contrast, the realization of O2-selective adsorbents may facilitate more widespread adoption of adsorptive air separations, which could enable the decentralization of O2 production and utilization and advance new uses for O2. Here, we present a detailed evaluation of the potential of metal-organic frameworks (MOFs) to serve as O2-selective adsorbents for air separations. Drawing insights from biological and molecular systems that selectively bind O2, we survey the field of O2-selective MOFs, highlighting progress and identifying promising areas for future exploration. As a guide for further research, the importance of moving beyond the traditional evaluation of O2 adsorption enthalpy, ΔH, is emphasized, and the free energy of O2 adsorption, ΔG, is discussed as the key metric for understanding and predicting MOF performance under practical conditions. Based on a proof-of-concept assessment of O2 binding carried out for eight different MOFs using experimentally derived capacities and thermodynamic parameters, we identify two existing materials and one proposed framework with nearly optimal ΔG values for operation under user-defined conditions. While enhancements are still needed in other material properties, the insights from the assessments herein serve as a guide for future materials design and evaluation. Computational approaches based on density functional theory with periodic boundary conditions are also discussed as complementary to experimental efforts, and new predictions enable identification of additional promising MOF systems for investigation.

Development of a sensor for trivalent iron: AHP fixed on mesoporous silica

Optical sensor for iron(iii) detection via Fe(iii) complexation in the solid phase.

Emerging Multifunctional Metal-Organic Framework Materials

Metal-organic frameworks (MOFs), also known as coordination polymers, represent an interesting type of solid crystalline materials that can be straightforwardly self-assembled through the coordination of metal ions/clusters with organic linkers. Owing to the modular nature and mild conditions of MOF synthesis, the porosities of MOF materials can be systematically tuned by judicious selection of molecular building blocks, and a variety of functional sites/groups can be introduced into metal ions/clusters, organic linkers, or pore spaces through pre-designing or post-synthetic approaches. These unique advantages enable MOFs to be used as a highly versatile and tunable platform for exploring multifunctional MOF materials. Here, the bright potential of MOF materials as emerging multifunctional materials is highlighted in some of the most important applications for gas storage and separation, optical, electric and magnetic materials, chemical sensing, catalysis, and biomedicine.

New short-channel SBA-15 mesoporous silicas functionalized with polyazamacrocyclic ligands for selective capturing of palladium ions in HNO3 media

Novel polyazamacrocyclic ligand decorated short-channel mesoporous silicas with the ability to selectively capture palladium ions in HNO₃ solutions.

Copper removal by carbon nanomaterials bearing cyclam-functionalized silica

The synthesis of metal (Fe, Co, Ni)-encapsulated carbon nanomaterials coated with cyclam-bonded silica has been described. The organic layer was identified by Fourier transform infrared spectroscopy and elemental analysis. The functionalized magnetic nanomaterials were employed to extract the divalent cations: copper, calcium, cobalt, manganese and nickel from aqueous solutions. Their adsorption capacities were studied by the batch procedure. The concentration of cations extracted was determined by inductively coupled plasma mass spectrometry. Influence of different parameters viz. pH, amount of the compound studied, contact time, on the cation extraction was investigated. Under optimum conditions copper extraction was significantly more efficient when compared with other coexisting ions.

Factors affecting copper(II) binding to multiarmed cyclam-grafted mesoporous silica in aqueous solution

Single- as well as multi-anchored cyclam-functionalized silica samples have been prepared by grafting amorphous silica gel (K60) and mesostructured silica (SBA-15) with silylated cyclam precursors bearing one, two, or four triethoxysilyl groups, respectively ascribed to cyclam-mono, cyclam-di, and cyclam-tetra. Their reactivity toward copper(II) has been thoroughly investigated in aqueous solution and discussed with respect to the number of arms tethering the ligand to the silica surface and the structural ordering of the adsorbent in terms of capacity, long-term stability, and speed of access to the binding sites. Less-than-complete metal ion uptake was always observed, even in excess of cyclam groups with respect to solution-phase Cu(II), suggesting lower stability of immobilized complexes relative to those in solution. Therefore, the number of arms attaching cyclam moieties to the silica walls (one, two, or four) was found to dramatically affect the binding properties of these hybrids toward copper(II), revealing significantly larger capacities when reducing the number of arms (less rigidity constraints in the macrocycle). In parallel, multiarm tethering resulted in better chemical resistance toward degradation as evidenced by UV-visible monitoring of Cu-cyclam complexes in solution (i.e., more ligand leaching from the adsorbent for singly tethered cyclam). On the other hand, electron spin resonance (ESR) experiments did not evidence significant differences between complexes bearing one, two, or four alkyl arms, since all Cu(II)-cyclam surface complexes were found to be hexacoordinated with a strong equatorial ligand field. Comparison of amorphous gels and mesostructured materials indicates that the binding properties of the adsorbents were hardly influenced by their level of ordering, suggesting that accessibility to the binding sites was not the limiting factor. Some advantage belonging to mesostructured adsorbents was however observed with respect to the rate of access to the active centers at pH values close to neutrality (due to faster mass transport), but this was no more the case when operating at lower pH values where the formation of the Cu-cyclam complex became the rate-determining step, as pointed out by electrochemistry.

Multiarm cyclam-grafted mesoporous silica: a strategy to improve the chemical stability of silica materials functionalized with amine ligands

We have explored in this work the stability and the reactivity of multiarm cyclam-grafted mesoporous silica samples in aqueous solution. A series of hybrid materials have been prepared by grafting silylated cyclam molecules bearing one, two, or four silyl groups onto both amorphous silica gel (K60) and ordered mesoporous silica (SBA15). Under these conditions, cyclam moieties are attached to the silica walls via one, two, or four arms. Various physicochemical techniques have been applied to characterize the functionalized solids (elemental analysis, 1H-29Si and 1H-13C CPMAS NMR, and N2 adsorption-desorption isotherms). The interest in two and four arms for improving the chemical stability in solution, by comparison with the system displaying only one arm, has been demonstrated by using a set of complementary experiments involving pH measurements and silicon determination with ICP-AES. Then, the investigation of their protonation and binding properties toward copper(II) has revealed a significant decrease in the reactivity of these hybrids as a consequence of multiarm tethering. A comparison of amorphous and ordered materials has permitted us to point out the influence of mesostructuration on the reactivity of these functionalized solids, especially from a kinetic point of view.

Nanoporous magnets of chiral and racemic [{Mn(HL)}2Mn{Mo(CN)7}2] with switchable ordering temperatures (TC = 85 K <--> 106 K) driven by H2O sorption (L = N,N-dimethylalaninol)

Molecule-based solids represent a rare opportunity to combine, adjust, and interrelate structural and physical functionalities to develop multifunctional materials. Here we report on a series of porous supramolecular magnets whose magnetic properties are related to their sorption state. A family of magnets of the formula [{Mn(HL)(H2O)}2Mn{Mo(CN)7}2].2H2O have been obtained by assembling the heptacyano-metalate building unit {Mo(CN)7}4- with Mn(II) in the presence of protonated N,N-dimethylalaninol (L) as ligand, the latter being either as a racemic mixture or as a chiral R- or S-enantiomer. The resulting magnets possess an open framework structure and exhibit a TC with a switching behavior (TC = 85 K <--> 106 K) as a function of the hydration state. Moreover, chiral magnets are formed with the optically active ligands. The H2O and gas (N2, CO2, CO) sorption features, the magnetic behavior of both the hydrated and dehydrated magnets, and the crystal structures of the hydrated chiral (S) and racemic magnets are described.

Exceptional Affinity of Nanostructured Organic–Inorganic Hybrid Materials towards Dioxygen: Confinement Effect of Copper Complexes

We report the exceptional reactivity towards dioxygen of a nanostructured organic-inorganic hybrid material due to the confinement of copper cyclam within a silica matrix. The key step is the metalation reaction of the ligand, which can occur before or after xerogel formation through the sol-gel process. The incorporation of a Cu(II) center into the material after xerogel formation leads to a bridged Cu(I)/Cu(II) mixed-valence dinuclear species. This complex exhibits a very high affinity towards dioxygen, attributable to auto-organization of the active species in the solid. The remarkable properties of these copper complexes in the silica matrix demonstrate a high cooperative effect for O(2) adsorption; this is induced by close confinement of the two copper ions leading to end-on mu-eta(1):eta(1)-peroxodicopper(II) complexes. The anisotropic packing of the tetraazamacrocycle in a lamellar structure induces an exceptional reactivity of these copper complexes. We show for the first time that the organic-inorganic environment of copper complexes in a silica matrix fully model the protecting role of protein in metalloenzymes. For the first time an oxygenated dicopper(II) complex can be isolated in a stable form at room temperature, and the reduced Cu(2) (I,I) species can be regenerated after several adsorption-desorption cycles. These data also demonstrate that the coordination scheme and reactivity of the copper cyclams within the solid are quite different from that observed in solution.

Selective Chemisorption of Carbon Monoxide by Organic–Inorganic Hybrid Materials Incorporating Cobalt(III) Corroles as Sensing Components

Twenty-one hybrid materials incorporating cobalt(III) corrole complexes were synthesized by a sol-gel process or by grafting the metallocorrole onto a mesostructured silica of the SBA-15 type. All the materials show an almost infinite selectivity for carbon monoxide with respect to dinitrogen and dioxygen in the low-pressure domain where the chemisorption phenomenon is predominant. This peculiar property is of prime importance for an application as a CO sensor. The selectivity slightly decreases at high pressures where nonselective physisorption phenomena mainly occur. The percentage of active sites for CO chemisorption ranges from 22 to 64 %. This low percentage may be attributable to interactions between the cobalt(III) corroles with silanol or siloxane groups remaining at the surface of the materials which prevent further coordination of the CO molecule. Notably, the most efficient materials are those prepared in the presence of a protecting ligand (pyridine) during the gelation or the grafting process. The removal of this ligand after the gelation process releases a cavity around the cobalt ion that favors the coordination of a carbon monoxide molecule. The CO adsorption properties of the SBA-15 hybrid were not affected over a period of several months thus indicating a high stability of the material. Conversely, the xerogel capacities slowly decrease owing to the evolution of the material structure.

Synthesis and metal complexation properties of Ph-DTPA and Ph-TTHA: novel radionuclide chelating agents for use in nuclear medicine

We wish to report the synthesis and metal complexation properties of new radionuclide chelating agents for use in nuclear medicine. The strategy includes the facile preparation of rigid analogues of DTPA and TTHA possessing an aromatic ring. The aromatic structure used increased the stability of the complexes formed (pre-organization concept) and they are easily functionalised for attaching to any support. The poly(amino)poly(carboxylic) acids, Ph-DTPA (5a) and Ph-TTHA (5b) were obtained in five steps from phenylenediamine as the starting material with overall yields of 42 and 20%, respectively. The key step in this synthetic process is the preparation of tri- and tetra-amino compounds, 3a and 3b, respectively. In order to assess the ability of both ligands to complex with different metals ((111)In, (153)Sm, (90)Y, (177)Lu, (213)Bi, (225)Ac), along with their suitability for use in nuclear medicine, we used a number of complementary tests. We were able to demonstrate the high complexation capacity of Ph-DTPA (5a) with a broad range of radionuclides in a slightly acidic medium. In vitro stability studies show the high stability of Ph-DTPA with (111)In in human serum, a necessary condition for all medical applications. The protonation constant (log K(H)(i)) of Ph-DTPA (5a) was determined by potentiometric methods.

Metallocorroles as sensing components for gas sensors: remarkable affinity and selectivity of cobalt(iii) corroles for CO vs. O2and N2

Most commercially available CO detectors are based upon metal oxides or electrochemical cell technologies. None of these approaches use the selective adsorption of CO gas on a molecular complex. Conversely, cobalt(III) corroles can bind small gaseous molecules allowing them for an application as sensing components for gas detectors. Here we describe the ability of cobalt corroles to selectively coordinate carbon monoxide vs. dinitrogen and dioxygen. The coordination properties were determined in the solid state and the adsorption characteristics were compared to those of the reference compound (To-PivPP)Fe(1,2-Me2Im), known for its remarkable CO binding properties. The adsorption data evidence that the selectivity, affinity and capacity of the cobalt(III) corroles for CO are larger than those of the porphyrin complex. However, from a chemical point of view, the selectivity of cobalt(III) corroles for CO vs. O2 is infinite since these derivatives do not bind O2 while (To-PivPP)Fe(1,2-Me2Im) does with an M value (PO2(1/2)/PCO(1/2)) equal to 51. In this manuscript we also show that the affinity of cobalt(III) corroles for CO is closely related to the Lewis acid character of the central cobalt(III) ion and therefore to the nature of the substituents at the periphery of the corrole macroring.