Electrochemical Polarization of Disparate Catalytic Sites Drives Thermochemical Rate Enhancement

Supported bimetallic catalysts commonly exhibit higher rates of reaction compared to their monometallic counterparts, but the origin of these enhancements is often poorly defined. The recent discovery that cooperative redox enhancement effects in Au-Pd systems promote bimetallic catalysis in thermochemical oxidation is an important development in this field. This effect aligns two important research fields, thermo- and electrocatalysis, but questions relating to the generality and origin of the effect remain. Here, we demonstrate that these effects can be observed in reactions over a range of bimetal combinations and reveal the origin using a combination of electrochemical and material characterization. We disclose that the observed activity enhancement in thermochemical systems is a result of the electrochemical polarization of two disparate catalytic sites. This forms an alternative operating potential for a given bimetallic system that increases the driving force of each of the composite half reactions in oxidative dehydrogenation. We therefore uncover the physicochemical descriptors that dictate whether these enhancement effects will be exhibited by a particular combination of supported metal catalysts and determine the magnitude of the effect.

Impact of the Experimental Parameters on Catalytic Activity When Preparing Polymer Protected Bimetallic Nanoparticle Catalysts on Activated Carbon

Sol immobilization is used to produce bimetallic catalysts with higher activity to monometallic counterparts for a wide range of environmental and commercial catalytic transformations. Analysis of complementary surface characterization (XPS, Boehm's titration, and zeta potential measurements) was used to elucidate alterations in the surface functionality of two activated carbon supports during acid exposure. When considered in parallel to the experimentally determined electrostatic and conformational changes of the polymer surrounding the nanoparticles, an electrostatic model is proposed describing polymer protected nanoparticle deposition with several polymer-carbon support examples described. Consideration of the electrostatic interactions ensures full deposition of the polymer protected nanoparticles and at the same time influences the structure of the bimetallic nanoparticle immobilized on the support. The normalized activity of AuPd catalysts prepared with 133 ppm H₂SO₄ has a much higher activity for the direct synthesis of hydrogen peroxide compared to catalysts prepared in the absence of acid. Detailed characterization by XPS indicates that the surface becomes enriched in Au in the Au-Pd samples prepared with acid, suggesting an improved dispersion of smaller bimetallic nanoparticles, rich in Au, that are known to be highly active for the direct synthesis reaction. Subsequent microscopy measurements confirmed this hypothesis, with the acid addition catalysts having a mean particle size ∼2 nm smaller than the zero acid counterparts. The addition of acid did not result in a morphology change, and random alloyed bimetallic AuPd nanoparticles were observed in catalysts prepared by sol immobilization in the presence and absence of acid. This work shows that the deposition of polymer protected AuPd nanoparticles onto activated carbon is heavily influenced by the acid addition step in the sol immobilization process. The physicochemical properties of both the polymer and the activated carbon support should be considered when designing a bimetallic nanoparticle catalyst by sol immobilization to ensure the optimum performance of the final catalyst.

Heterogeneous Trimetallic Nanoparticles as Catalysts

The development and application of trimetallic nanoparticles continues to accelerate rapidly as a result of advances in materials design, synthetic control, and reaction characterization. Following the technological successes of multicomponent materials in automotive exhausts and photovoltaics, synergistic effects are now accessible through the careful preparation of multielement particles, presenting exciting opportunities in the field of catalysis. In this review, we explore the methods currently used in the design, synthesis, analysis, and application of trimetallic nanoparticles across both the experimental and computational realms and provide a critical perspective on the emergent field of trimetallic nanocatalysts. Trimetallic nanoparticles are typically supported on high-surface-area metal oxides for catalytic applications, synthesized via preparative conditions that are comparable to those applied for mono- and bimetallic nanoparticles. However, controlled elemental segregation and subsequent characterization remain challenging because of the heterogeneous nature of the systems. The multielement composition exhibits beneficial synergy for important oxidation, dehydrogenation, and hydrogenation reactions; in some cases, this is realized through higher selectivity, while activity improvements are also observed. However, challenges related to identifying and harnessing influential characteristics for maximum productivity remain. Computation provides support for the experimental endeavors, for example in electrocatalysis, and a clear need is identified for the marriage of simulation, with respect to both combinatorial element screening and optimal reaction design, to experiment in order to maximize productivity from this nascent field. Clear challenges remain with respect to identifying, making, and applying trimetallic catalysts efficiently, but the foundations are now visible, and the outlook is strong for this exciting chemical field.

Gold Nanoparticles as Efficient Catalysts in Organic Transformations

This review summarizes the utilization of gold nanoparticles as efficient catalysts for a variety of chemical transformations like oxidation, hydrogenation, and coupling reactions as compared to conventional catalytic materials. This review explores the gold nanoparticles-based catalysts for the liquid phase chemo-selective organic transformations which are proving to be evergreen reactions and have importance for industrial applications. Apart from organic transformation reactions, gold nanoparticles have been found to be applicable in removing the atmospheric contaminants and improving the efficiency of the fuel cells by removing the impurities of carbon monoxide.

Pd Nanoparticles-Loaded Vinyl Polymer Gels: Preparation, Structure and Catalysis

Four vinyl polymer gels (VPGs) were synthesized by free radical polymerization of divinylbenzene, ethane-1,2-diyl dimethacrylate, and copolymerization of divinylbenzene with styrene, and ethane-1,2-diyl dimethacrylate with methyl methacrylate, as supports for palladium nanoparticles. VPGs obtained from divinylbenzene and from divinylbenzene with styrene had spherical shapes while those obtained from ethane-1,2-diyl dimethacrylate and from ethane-1,2-diyl dimethacrylate with methyl methacrylate did not have any specific shapes. Pd(OAc)2 was impregnated onto VPGs and reduced to form Pd0 nanoparticles within VPGs. The structures of Pd0-loaded VPGs were analyzed by XRD, TEM, and nitrogen gas adsorption. Pd0-loaded VPGs had nanocrystals of Pd0 within and on the surface of the polymeric supports. Pd0/VPGs efficiently catalyzed the oxidation/disproportionation of benzyl alcohol into benzaldehyde/toluene, where activity and selectivity between benzaldehyde and toluene varied, depending on the structure of VPG and the weight percentage loading of Pd0. The catalysts were stable and Pd leaching to liquid phase did not occur. The catalysts were separated and reused for five times without any significant decrease in the catalytic activity.

High H2O2 Utilization Promotes Selective Oxidation of Methane to Methanol at Low Temperature

Selective oxidation of methane to methanol has been often considered as a “holy grail” reaction in catalysis. Herein, we systematically investigate the effect of solution pH and Pd-to-Au ratio of AuPd_x colloid on the catalytic performance of methane oxidation. It is revealed that these two parameters can determine the amount of H₂O₂ participated in the reaction, which is linearly related to the productivity of oxygenates. A high catalytic performance in methane activation requires a high utilization of H₂O₂ to generate more ·OH. The optimal pH is 3.0 and the optimal Pd-to-Au ratio is between 0.1 to 0.7.

Preformed Pd-Based Nanoparticles for the Liquid Phase Decomposition of Formic Acid: Effect of Stabiliser, Support and Au–Pd Ratio

Hydrogen is one of the most promising energy carriers for the production of electricity based on fuel cell hydrogen technology. Recently, hydrogen storage chemicals, such as formic acid, have been proposed to be part of the long-term solution towards hydrogen economy for the future of our planet. Herein we report the synthesis of preformed Pd nanoparticles using colloidal methodology varying a range of specific experimental parameters, such as the amount of the stabiliser and reducing agent, nature of support and Pd loading of the support. The aforementioned parameters have shown to affect mean Pd particle size, Pd oxidation, atomic content of Pd on the surface as well as on the catalytic performance towards formic acid decomposition. Reusability studies were carried out using the most active monometallic Pd material with a small loss of activity after five uses. The catalytic performance based on the Au–Pd atomic ratio was evaluated and the optimum catalytic performance was found to be with the Au/Pd atomic ratio of 1/3, indicating that the presence of a small amount of Pd is essential to promote significantly Au activity for the liquid phase decomposition of formic acid. Thorough characterisation has been carried out by means of XPS, SEM-EDX, TEM and BET. The observed catalytic performance is discussed in terms of the structure/morphology and composition of the supported Pd and Au–Pd nanoparticles.

Nanomagnet-Silica Nanoparticles Decorated with Au@Pd for Enhanced Peroxidase-Like Activity and Colorimetric Glucose Sensing

Nanomagnet-silica shell (Fe₃O₄@SiO₂) decorated with Au@Pd nanoparticles (NPs) were synthesized successfully. The characterization of Fe₃O₄@SiO₂-NH₂-Au@PdNPs was achieved using several spectroscopic and microscopic techniques. The quantitative surface analysis was confirmed using X-ray photoelectron spectroscopy. The Fe₃O₄@SiO₂-NH₂-Au@Pd_0.30NPs exhibited excellent peroxidase-like activity by effectively catalyzing the oxidation of 3,3',5,5'-tetramethylbenzidine (TMB) in the presence of H₂O₂. The absorption peaks at 370 and 652 nm confirmed the peroxidase-like activity of the Fe₃O₄@SiO₂-NH₂-Au@Pd_0.30NPs. The Michaelis-Menten constant (K_m) of 0.350 and 0.090 mM showed strong affinity toward H₂O₂ and TMB at Fe₃O₄@SiO₂-NH₂-Au@Pd_0.30NPs. The mechanism of the peroxidase-like activity was found to proceed via an electron transfer process. A simple colorimetric sensor based on glucose oxidase and Fe₃O₄@SiO₂-NH₂-Au@Pd_0.30NPs showed excellent selectivity and sensitivity towards the detection of glucose. The fabricated glucose biosensor exhibited a wide linear response toward glucose from 0.010 to 60.0 μM with an limit of detection of 60.0 nM and limit of quantification of 200 nM. The colorimetric biosensor based on Fe₃O₄@SiO₂-NH₂-Au@Pd_0.30NPs as a peroxidase mimic was also successfully applied for the determination of glucose concentrations in serum samples. The synthesized Fe₃O₄@SiO₂-NH₂-Au@Pd_0.30NPs nanozymes exhibited excellent potential as an alternative to horseradish peroxidase for low-cost glucose monitoring.

Enhanced catalyst selectivity in the direct synthesis of H2O2 through Pt incorporation into TiO2 supported AuPd catalysts

The introduction of low levels of Pt dopant into AuPd nanoparticles supported on TiO₂ significantly enhances their catalytic performance for the direct synthesis of H₂O₂.

Gold nanomaterials as key suppliers in biological and chemical sensing, catalysis, and medicine

BACKGROUND

Gold nanoparticles (AuNPs) with unique physicochemical properties have received a great deal of interest in the field of biological, chemical and biomedical implementations. Despite the widespread use of AuNPs in chemical and biological sensing, catalysis, imaging and diagnosis, and more recently in therapy, no comprehensive summary has been provided to explain how AuNPs could aid in developing improved sensing and catalysts systems as well as medical settings.

SCOPE OF REVIEW

The chemistry of Au-based nanosystems was followed by reviewing different applications of Au nanomaterials in biological and chemical sensing, catalysis, imaging and diagnosis by a number of approaches, and finally synergistic combination therapy of different cancers. Afterwards, the clinical impacts of AuNPs, future application of AuNPs, and opportunities and challenges of AuNPs application were also discussed.

MAJOR CONCLUSIONS

AuNPs show exclusive colloidal stability and are considered as ideal candidates for colorimetric detection, catalysis, imaging, and photothermal transducers, because their physicochemical properties can be tuned by adjusting their structural dimensions achieved by the different manufacturing methods.

GENERAL SIGNIFICANCE

This review provides some details about using AuNPs in sensing and catalysis applications as well as promising theranostic nanoplatforms for cancer imaging and diagnosis, and sensitive, non-invasive, and synergistic methods for cancer treatment in an almost comprehensive manner.

Rapid Microwave-Assisted Polyol Synthesis of TiO2-Supported Ruthenium Catalysts for Levulinic Acid Hydrogenation

One wt% Ru/TiO2 catalysts prepared by a one-pot microwave-assisted polyol method have been shown to be highly active for Levulinic acid hydrogenation to γ-Valerolactone. Preparation temperature, microwave irradiation time and choice of Ru precursor were found to have a significant effect on catalyst activity. In the case of Ru(acac)3-derived catalysts, increasing temperature and longer irradiation times increased catalyst activity to a maximum LA conversion of 69%. Conversely, for catalysts prepared using RuCl3, shorter preparation times and lower temperatures yielded more active catalysts, with a maximum LA conversion of 67%. Catalysts prepared using either precursor were found to contain highly dispersed nanoparticles <3 nm in diameter. XPS analysis of the most and least active catalysts shows that the catalyst surface is covered in a layer of insoluble carbon with surface concentrations exceeding 40% in some cases. This can be attributed to the formation of large condensation oligomers from the reaction between the solvent, ethylene glycol and its oxidation products, as evidenced by the presence of C-O and C = O functionality on the catalyst surface.

Heterogeneous Gold Catalysis: From Discovery to Applications

In the present review, the important and current developments of gold catalysts for a wide range of applications are comprehensively summarized. This review also provides a detailed study of the literature data concerning the preparation, characterization, and catalytic applications of gold catalysts. Additionally, the main aspects of using supported gold nanoparticles (AuNPs) as catalysts for oxidation reactions are considered. In particular, the oxidation of benzyl alcohol to benzaldehyde and the production of adipic acid from cyclohexane are discussed in detail. Lastly, the key properties of gold catalysts are described, and an outlook on the application of gold catalysts is presented.

Synthesis of highly uniform and composition-controlled gold-palladium supported nanoparticles in continuous flow

The synthesis of supported bimetallic nanoparticles with well-defined size and compositional parameters has long been a challenge. Although batch colloidal methods are commonly used to pre-form metal nanoparticles with the desired size-range in solution, inhomogeneous mixing of the reactant solutions often leads to variations in size, structure and composition from batch-to-batch and even particle-to-particle. Here we describe a millifluidic approach for the production of oxide supported monometallic Au and bimetallic AuPd nanoparticles in a continuous fashion. This optimised method enables the production of nanoparticles with smaller mean sizes, tighter particle size distributions and a more uniform particle-to-particle chemical composition as compared to the conventional batch procedure. In addition, we describe a facile procedure to prepare bimetallic Au@Pd core-shell nanoparticles in continuous flow starting from solutions of the metal precursors. Moreover, the relative ease of scalability of this technique makes the proposed methodology appealing not only for small-scale laboratory purposes, but also for the industrial-scale production of supported metal nanoparticles.

The preparation of large surface area lanthanum based perovskite supports for AuPt nanoparticles: tuning the glycerol oxidation reaction pathway by switching the perovskite B site

Gold and gold alloys, in the form of supported nanoparticles, have been shown over the last three decades to be highly effective oxidation catalysts. Mixed metal oxide perovskites, with their high structural tolerance, are ideal for investigating how changes in the chemical composition of supports affect the catalysts' properties, while retaining similar surface areas, morphologies and metal co-ordinations. However, a significant disadvantage of using perovskites as supports is their high crystallinity and small surface area. We report the use of a supercritical carbon dioxide anti-solvent precipitation methodology to prepare large surface area lanthanum based perovskites, making the deposition of 1 wt% AuPt nanoparticles feasible. These catalysts were used for the selective oxidation of glycerol. By changing the elemental composition of the perovskite B site, we dramatically altered the reaction pathway between a sequential oxidation route to glyceric or tartronic acid and a dehydration reaction pathway to lactic acid. Selectivity profiles were correlated to reported oxygen adsorption capacities of the perovskite supports and also to changes in the AuPt nanoparticle morphologies. Extended time on line analysis using the best oxidation catalyst (AuPt/LaMnO₃) produced an exceptionally high tartronic acid yield. LaMnO₃ produced from alternative preparation methods was found to have lower activities, but gave comparable selectivity profiles to that produced using the supercritical carbon dioxide anti-solvent precipitation methodology.

The selective hydrogenation of furfural over supported palladium nanoparticle catalysts prepared by sol-immobilisation: effect of catalyst support and reaction conditions

Pd-TiO₂ nanoparticles prepared by sol-immobilisation are very active for selective hydrogenation of furfural under mild conditions, and addition of Pt enhances performance to achieve a 95% yield of tetrahydrofurfuryl alcohol.

Cinnamyl alcohol oxidation using supported bimetallic Au–Pd nanoparticles: an investigation of autoxidation and catalysis

In this study, we examine autoxidation and its role on the catalytic aerobic oxidation of cinnamyl alcohol using supported AuPd nanoparticles.

One pot microwave synthesis of highly stable AuPd@Pd supported core–shell nanoparticles

A series of 1 wt% supported Au, Pd and AuPd nanoalloy catalysts were prepared via microwave assisted reduction of PdCl₂ and HAuCl₄ in a facile, one pot process.

The role and fate of capping ligands in colloidally prepared metal nanoparticle catalysts

In this Perspective article, we highlight emerging opportunities for the rational design of catalysts upon the choice, exchange, partial removal or pyrolysis of ligands.

The controlled catalytic oxidation of furfural to furoic acid using AuPd/Mg(OH)2

The selective oxidation of furfural to furoic acid is achieved at mild reaction conditions over an AuPd/Mg(OH)₂ heterogeneous catalyst.

Carbon nanotube-supported Au–Pd alloy with cooperative effect of metal nanoparticles and organic ketone/quinone groups as a highly efficient catalyst for aerobic oxidation of amines

Au–Pd alloy nanoparticles loaded on CNTs with high surface concentrations of ketone/quinone groups are efficient for aerobic oxidation of amines.

Oxidation of benzyl alcohol catalyzed by gold nanoparticles under alkaline conditions: weak vs. strong bases

A comparative study of the promotion effect of weak and strong bases in the aqueous oxidation of benzyl alcohol by Au/TiO₂ showed that better conversion and aldehyde selectivity can be obtained using weak bases.

Characterisation of gold catalysts

Au-based catalysts have established a new important field of catalysis, revealing specific properties in terms of both high activity and selectivity for many reactions.

Synthesis of Carboxylic Acid by 2-Hexenal Oxidation Using Gold Catalysts Supported on MnO2

Synthesis of carboxylic acid can be achieved by the oxidation of aldehyde using air as an oxidant in the presence of a potential catalyst. We demonstrated that 2-hexenal can be oxidized to carboxylic acid by Au, Pd, and Au-Pd catalysts and investigated the effects of catalyst support (graphite, TiO2, MgO, SiC, MnO2, CeO2, and Al2O3), preparation method for supported catalyst (sol immobilization, impregnation, and deposition precipitation), and choice of catalyst components. Analysis of conversion% and selectivity% for 2-hexenoic acid showed that MnO2-supported gold nanoparticles are the best catalysts for 2-hexenal oxidation. Moreover, catalysts prepared by sol immobilization are the most active possibly due to the much smaller gold nanoparticle size. Selectivity for 2-hexenoic acid is a major pathway of oxidation of 2-hexenal.

Ce(0.6)Zr(0.3)Y(0.1)O(2) nanorod supported gold and palladium alloy nanoparticles: high-performance catalysts for toluene oxidation

The Ce0.6Zr0.3Y0.1O2 (CZY) nanorods and their supported gold and palladium alloy (zAuxPdy/CZY; z = 0.80-0.93 wt%; x or y = 0, 1, 2) nanoparticles (NPs) were prepared using the cetyltrimethyl ammonium bromide-assisted hydrothermal and polyvinyl alcohol-protected reduction methods, respectively. Physicochemical properties of the samples were characterized by means of numerous analytical techniques, and their catalytic activities were evaluated for the oxidation of toluene. It is shown that the CZY in zAuxPdy/CZY was cubic in crystal structure, surface areas of CZY and zAuxPdy/CZY were in the range 68-77 m(2) g(-1), and the Au-Pd NPs with a size of 4.6-5.6 nm were highly dispersed on the surface of CZY nanorods. Among all the samples, 0.90Au1Pd2/CZY possessed the highest adsorbed oxygen concentration and the best low-temperature reducibility, and performed the best: T50% and T90% (temperatures required for achieving toluene conversions of 50 and 90%) were 190 and 218 °C at a space velocity of 20 000 mL (g h)(-1), respectively. The partial deactivation due to water vapor introduction was reversible. The active sites might be the surface oxygen vacancies on CZY, oxidized noble metal NPs, and/or interfaces between noble metal NPs and CZY. The apparent activation energies (37-43 kJ mol(-1)) obtained over 0.90-0.93AuxPdy/CZY were much lower than that (88 kJ mol(-1)) obtained over CZY for toluene oxidation. It is concluded that the excellent catalytic performance of 0.90Au1Pd2/CZY was associated with its high adsorbed oxygen species concentration, good low-temperature reducibility, and strong interaction between Au-Pd NPs and CZY nanorods as well as good dispersion of Au-Pd NPs.

New challenges in gold catalysis: bimetallic systems

Since the discovery of the peculiar catalytic activity of gold catalysts, it became clear that gold could play a fundamental role also as a modifier.

Strategies for designing supported gold-palladium bimetallic catalysts for the direct synthesis of hydrogen peroxide

Hydrogen peroxide is a widely used chemical but is not very efficient to make in smaller than industrial scale. It is an important commodity chemical used for bleaching, disinfection, and chemical manufacture. At present, manufacturers use an indirect process in which anthraquinones are sequentially hydrogenated and oxidized in a manner that hydrogen and oxygen are never mixed. However, this process is only economic at a very large scale producing a concentrated product. For many years, the identification of a direct process has been a research goal because it could operate at the point of need, producing hydrogen peroxide at the required concentration for its applications. Research on this topic has been ongoing for about 100 years. Until the last 10 years, catalyst design was solely directed at using supported palladium nanoparticles. These catalysts require the use of bromide and acid to arrest peroxide decomposition, since palladium is a very active catalyst for hydrogen peroxide hydrogenation. Recently, chemists have shown that supported gold nanoparticles are active when gold is alloyed with palladium because this leads to a significant synergistic enhancement in activity and importantly selectivity. Crucially, bimetallic gold-based catalysts do not require the addition of bromide and acids, but with carbon dioxide as a diluent its solubility in the reaction media acts as an in situ acid promoter, which represents a greener approach for peroxide synthesis. The gold catalysts can operate under intrinsically safe conditions using dilute hydrogen and oxygen, yet these catalysts are so active that they can generate peroxide at commercially significant rates. The major problem associated with the direct synthesis of hydrogen peroxide concerns the selectivity of hydrogen usage, since in the indirect process this factor has been finely tuned over decades of operation. In this Account, we discuss how the gold-palladium bimetallic catalysts have active sites for the synthesis and hydrogenation of hydrogen peroxide that are different, in contrast to monometallic palladium in which synthesis and hydrogenation operate at the same sites. Through treatment of the support with acids prior to the deposition of the gold-palladium bimetallic particles, we can obtain a catalyst that can make hydrogen peroxide at a very high rate without decomposing or hydrogenating the product. This innovation opens up the way to design improved catalysts for the direct synthesis process, and these possibilities are described in this Account.

High activity redox catalysts synthesized by chemical vapor impregnation

The use of precious metals in heterogeneous catalysis relies on the preparation of small nanoparticles that are stable under reaction conditions. To date, most conventional routes used to prepare noble metal nanoparticles have drawbacks related to surface contamination, particle agglomeration, and reproducibility restraints. We have prepared titania-supported palladium (Pd) and platinum (Pt) catalysts using a simplified vapor deposition technique termed chemical vapor impregnation (CVI) that can be performed in any standard chemical laboratory. These materials, composed of nanoparticles typically below 3 nm in size, show remarkable activity under mild conditions for oxidation and hydrogenation reactions of industrial importance. We demonstrate the preparation of bimetallic Pd-Pt homogeneous alloy nanoparticles by this new CVI method, which show synergistic effects in toluene oxidation. The versatility of our CVI methodology to be able to tailor the composition and morphology of supported nanoparticles in an easily accessible and scalable manner is further demonstrated by the synthesis of Pdshell-Aucore nanoparticles using CVI deposition of Pd onto preformed Au nanoparticles supported on titania (prepared by sol immobilization) in addition to the presence of monometallic Au and Pd nanoparticles.

Liquid phase oxidation of glycerol in batch and flow-type reactors with oxygen over Au–Pd nanoparticles stabilized in anion-exchange resin

Au–Pd bimetallic nanoparticles for selective oxidation of glycerol were successfully prepared in a commercial ion-exchange resin.