Advances in Heterogeneous Catalysts for Lignin Hydrogenolysis

Lignin is the main component of lignocellulose and the largest source of aromatic substances on the earth. Biofuel and bio-chemicals derived from lignin can reduce the use of petroleum products. Current advances in lignin catalysis conversion have facilitated many of progress, but understanding the principles of catalyst design is critical to moving the field forward. In this review, the factors affecting the catalysts (including the type of active metal, metal particle size, acidity, pore size, the nature of the oxide supports, and the synergistic effect of the metals) are systematically reviewed based on the three most commonly used supports (carbon, oxides, and zeolites) in lignin hydrogenolysis. The catalytic performance (selectivity and yield of products) is evaluated, and the emerging catalytic mechanisms are introduced to better understand the catalyst design guidelines. Finally, based on the progress of existing studies, future directions for catalyst design in the field of lignin depolymerization are proposed.

Engineering mesoporous silica nanoparticles for drug delivery: where are we after two decades?

The present review details a chronological description of the events that took place during the development of mesoporous materials, their different synthetic routes and their use as drug delivery systems. The outstanding textural properties of these materials quickly inspired their translation to the nanoscale dimension leading to mesoporous silica nanoparticles (MSNs). The different aspects of introducing pharmaceutical agents into the pores of these nanocarriers, together with their possible biodistribution and clearance routes, would be described here. The development of smart nanocarriers that are able to release a high local concentration of the therapeutic cargo on-demand after the application of certain stimuli would be reviewed here, together with their ability to deliver the therapeutic cargo to precise locations in the body. The huge progress in the design and development of MSNs for biomedical applications, including the potential treatment of different diseases, during the last 20 years will be collated here, together with the required work that still needs to be done to achieve the clinical translation of these materials. This review was conceived to stand out from past reports since it aims to tell the story of the development of mesoporous materials and their use as drug delivery systems by some of the story makers, who could be considered to be among the pioneers in this area.

Polyaniline inside the pores of high surface area mesoporous silicon as composite electrode material for supercapacitors

Mesoporous silicon (mSi) obtained by the magnesiothermic reduction of mesoporous silica was used to deposit polyaniline (PANI) in its pores, the composite was tested for its charge storage application for high performance supercapacitor electrodes. The mesoporous silica as confirmed by Small Angle X-ray Scattering (SAXS) has a Brunauer-Emmett-Teller (BET) surface area of 724 m2g-1 and mean pore size of 5 nm. After magnesiothermic reduction to mSi, the BET surface area is reduced to 348 m2g-1 but the mesoporousity is retained with a mean pore size of 10 nm. The BET surface area of mesoporous silicon is among the highest for porous silicon prepared/reduced from silica. In situ polymerization of PANI inside the pores of mSi was achieved by controlling the polymerization conditions. As a supercapacitor electrode, the mSi-PANI composite exhibits better charge storage performance as compared to pure PANI and mesoporous silica-PANI composite electrodes. Enhanced electrochemical performance of the mSi-PANI composite is attributed to the high surface mesoporous morphology of mSi with a network structure containing abundant mesopores enwrapped by an electrochemically permeable polyaniline matrix.

Tunable Effect of the Calcination of the Silanol Groups of KIT-6 and SBA-15 Mesoporous Materials

The calcination process is a crucial step during SBA-15 and KIT-6 synthesis. It is used to completely remove the organic template and condense silanol groups, and it allows the determination of the textural and physical properties of these materials, depending on the adopted conditions. Moreover, calcination influences the number of silanols available on the surface of the material. The concentration of silanols is important if these materials were synthesized for use in adsorption or functionalization. To understand and optimize the silanol groups of SBA-15 and KIT-6, in this study, the temperature and time calcination parameters were varied. The experiments were performed at 300, 400, and 500 °C for 300, 400, and 500 min. The results show that the ideal temperature to preserve the silanol groups is 300 °C, but to optimize the textural properties, it is better to calcine these molecular sieves at 400 °C. A calcination for 10 h did not give better results than a calcination for 5 h, demonstrating that the former duration is excessive for use.

Catalytic depolymerization of the hydrolyzed lignin over mesoporous catalysts

In this work, the mesoporous SBA-15 and a series of modified catalysts based on it, such as Al-SBA-15 and Ni/Al-SBA-15, were synthesized and used for eliminating the char formation during the depolymerization of hydrolyzed lignin. The temperature, time and solvent effects on the lignin depolymerization were also investigated. Results showed that the repolymerization was effectively suppressed over SBA-15 due to its well-ordered pore structure and large pore size. The addition of Al and Ni elements in SBA-15 could improve the lignin depolymerization performance and saturate the instable intermediates. Ethanol was found to be more effective in suppressing repolymerization than other solvents. 81.4% liquefaction degree and 21.90wt% monomer yield was achieved, and no obvious char was observed after the depolymerization of hydrolyzed lignin in ethanol solvent at 300°C for 4h over Ni/Al-SBA-15(20) catalyst.

Sensing Properties of GO and Amine-Silica Nanoparticles Functionalized QCM Sensors for Detection of Formaldehyde

In the current work, graphene oxides (GO) and Amine-Functionalized Silica Nanoparticles ( NH 2-SNs) were used as sensing layer on quart crystal microbalance (QCM) for detection of HCHO gas. The GO and NH 2-SNs functionalized QCM resonators all had a significant response to HCHO gas. The sensitivity of GO functionalized QCM resonator is 0.04 Hz/(μg⋅ppm), which is four times as high as that of NH 2-SNs functionalized QCM resonator (0.01 Hz/(μg⋅ppm)). The GO functionalized QCM resonators would be of benefit in area of environmental applications.

Hydrothermal synthesis of Co–ZnO nanowire array and its application as piezo-driven self-powered humidity sensor with high sensitivity and repeatability

Self-powered humidity sensor with high sensitivity and repeatability has been fabricated from Co-doped ZnO NW arrays. Such a high performance can be attributed to the piezo-surface coupling effect and more active sites introduced by the Co dopants.

Synthesis of Ni(II)-imprinted Mesoporous Silica Adsorbents by Surface Imprinting Technology for Removal of Ni(II) from Aqueous Solution

Ni(II)-imprinted polymer has been prepared by surface imprinting technique based on support matrix of mesoporous silica SBA-15. The obtained adsorbent was characterized by FT-IR, SEM, and nitrogen adsorption-desorption. The compound retained mesoporous structure and the polymer coated inside channels and outside surface hole wall. The adsorption behavior was carried out with Ni(II)-IIP in batch experiments. The results suggested that Ni(II)-IIP could be used as an excellent adsorbent for efficient removal of Ni(II) from aqueous solution.

A robust graft-to strategy to form multifunctional and stealth zwitterionic polymer-coated mesoporous silica nanoparticles

Mesoporous silica nanoparticles (MSNs) are a new class of carrier materials promising for drug/gene delivery and many other important applications. Stealth coatings are necessary to maintain their stability in complex media. Herein, a biomimetic polymer conjugate containing one ultralow fouling poly(carboxybetaine) (pCBMA) chain and one surface-adhesive catechol (DOPA) residue group was efficiently grafted to the outer surface of SBA-15 type MSNs using a convenient and robust method. The cytotoxicity of SBA-15-DOPA-pCBMAs was evaluated by the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay. Results showed no significant decrease in cell viability at the tested concentration range. Macrophage cell uptake studies revealed that the uptake ratios of SBA-15-DOPA-pCBMAs were much lower than that of parent MSNs. Furthermore, inductively coupled plasma mass spectrometry (ICP-MS) analysis results showed that after SBA-15-DOPA-pCBMAs were conjugated with a targeting cyclo-[Arg-Gly-Asp-d-Tyr-Lys] (cRGD) peptide, uptake by bovine aortic endothelial cells (BAECs) was notably increased. Results indicated that cRGD-functionalized MSNs were able to selectively interact with cells expressing αvβ3 integrin. Thus, MSNs with DOPA-pCBMAs are promising as stealth multifunctional biocarriers for targeted drug delivery or diagnostics.

Amine-functionalized SBA-15 with uniform morphology and well-defined mesostructure for highly sensitive chemosensors to detect formaldehyde vapor

Amine-functionalized SBA-15 with uniform morphology and well-defined mesostructure was prepared using a postgrafting route. The morphology, mesostructure, and functionality of the materials were characterized by scanning electron microscopy, transmission electron microscopy, small-angle X-ray scattering, nitrogen adsorption-desorption, Fourier transform infrared spectroscopy, and solid-state nuclear magnetic resonance spectroscopy techniques. The results show that hexagonal lamelliform SBA-15 with a uniform particle size and short vertical channels plays two significant roles in uniformly dispersing amine-functionalizing groups and effectively adjusting the loadings of the functional groups within the mesopore channels. To confirm the potential application of the hybrids in gas sensors, using amine-functionalized SBA-15 as a sensing material and a quartz crystal microbalance as a transducer, a parts per billion level formaldehyde sensor with high sensitivity (response time about 11 s, recovery time about 15 s) and good chemoselectivity was achieved. This material holds great potential in the area of rapid, sensitive, and highly convenient formaldehyde detection.