Magnetic anisotropy engineering in onion-structured metal oxide nanoparticles combining dual exchange coupling and proximity effects

A series of exchange-coupled magnetic nanoparticles combining several magnetic phases in an onion-type structure were synthesized by performing a three-step seed-mediated growth process. Iron and cobalt precursors were alternatively decomposed in high-boiling-temperature solvents (288-310 °C) to successively grow CoO and Fe3-δO4 shells (the latter in three stages) on the surface of Fe3-δO4 seeds. The structure and chemical composition of these nanoparticles were investigated in depth by combining a wide panel of advanced techniques, such as scanning transmission electron microscopy (STEM), electron energy-loss spectroscopy-spectrum imaging (EELS-SI), 57Fe Mössbauer spectrometry, and X-ray circular magnetic dichroism (XMCD) techniques. The size of the nanoparticles increased progressively after each thermal decomposition step, but the crystal structure of core-shell nanoparticles was significantly modified during the growth of the second shell. Indeed, the antiferromagnetic CoO phase was progressively replaced by the CoFe2O4 ferrimagnet due to the concomitant processes of partial solubilization/crystallization and the interfacial cationic diffusion of iron. A much more complex chemical structure than that suggested by a simple size variation of the nanoparticles is thus proposed, namely Fe3-δO4@CoO-CoFe2O4@Fe3-δO4, where an intermediate Co-based layer was shown to progressively become a single, hybrid magnetic phase (attributed to proximity effects) with a reduction in the CoO amount. In turn, the dual exchange-coupling of this hybrid Co-based intermediate layer (with high anisotropy and ordering temperature) with the surrounding ferrite (core and outer shells) stabilized the particle moment well above room temperature. These effects allow for the production of Fe oxide-based magnetic nanoparticles with high effective anisotropy, thus revealing the potential of this strategy to design rare-earth-free permanent nanomagnets at room temperature.

Mesoscale self-organization of polydisperse magnetic nanoparticles at the water surface

In this study, we investigated the self-ordering process in Langmuir films of polydisperse iron oxide nanoparticles on a water surface, employing in situ x-ray scattering, surface pressure-area isotherm analysis, and Brewster angle microscopy. X-ray reflectometry confirmed the formation of a monolayer, while grazing incidence small-angle x-ray scattering revealed short-range lateral correlations with a characteristic length equal to the mean particle size. Remarkably, our findings indicated that at zero surface pressure, the particles organized into submicrometer clusters, merging upon compression to form a homogeneous layer. These layers were subsequently transferred to a solid substrate using the Langmuir-Schaefer technique and further characterized via scanning electron microscopy and polarized neutron reflectometry. Notably, our measurements revealed a second characteristic length in the lateral correlations, orders of magnitude longer than the mean particle diameter, with polydisperse particles forming circular clusters densely packed in a hexagonal lattice. Furthermore, our evidence suggests that the lattice constant of this mesocrystal depends on the characteristics of the particle size distribution, specifically the mean particle size and the width of the size distribution. In addition, we observed internal size separation within these clusters, where larger particles were positioned closer to the center of the cluster. Finally, polarized neutron reflectometry measurements provided valuable insights into the magnetization profile across the layer.

Annealing effects on the magnetic and magnetotransport properties of iron oxide nanoparticles self-assemblies

In magnetic tunnel junctions based on iron oxide nanoparticles the disorder and the oxidation state of the surface spin as well as the nanoparticles functionalization play a crucial role in the magnetotransport properties. In this work, we report a systematic study of the effects of vacuum annealing on the structural, magnetic and transport properties of self-assembled ∼10 nm Fe3O4nanoparticles. The high temperature treatment (from 573 to 873 K) decomposes the organic coating into amorphous carbon, reducing the electrical resistivity of the assemblies by 4 orders of magnitude. At the same time, the 3.Fe2+/(Fe3++Fe2+) ratio is reduced from 1.11 to 0.13 when the annealing temperature of the sample increases from 573 to 873 K, indicating an important surface oxidation. Although the 2 nm physical gap remains unchanged with the thermal treatment, a monotonous decrease of tunnel barrier width was obtained from the electron transport measurements when the annealing temperature increases, indicating an increment in the number of defects and hot-spots in the gap between the nanoparticles. This is reflected in the reduction of the spin dependent tunneling, which reduces the interparticle magnetoresistance. This work shows new insights about influence of the nanoparticle interfacial composition, as well their the spatial arrangement, on the tunnel transport of self-assemblies, and evidence the importance of optimizing the nanostructure fabrication for increasing the tunneling current without degrading the spin polarized current.

Construction of Millimeter-Wide Monolayers of Ordered Nanocubes as a Stain of "Wineglass Tears" Driven by the Marangoni Flow

We constructed millimeter-wide monolayers consisting of tetragonally ordered BaTiO₃ (BT) nanocubes through the liquid film formation caused by the Marangoni flow in a toluene-hexane binary liquid containing oleic acid. A thin liquid film containing BT nanocubes was overspread on a standing silicon substrate through the condensation of toluene at the advancing front after the preferential evaporation of hexane. Then, the oscillatory droplet formation like "wineglass tears" occurred on the substrate. Finally, two-dimensionally ordered BT nanocubes were observed as a stain of "wineglass tears" on the substrate after the liquid film receded through evaporation. The presence of a thin liquid film in the binary system is essential for the production of millimeter-wide monolayers on the substrate because multilayer deposition occurs without the formation of a thin liquid film in monocomponent systems. We improved the regularity of the ordered arrays of nanocubes by adjusting the liquid component and evaporation conditions.

Fabrication of a Dual Stimuli-Responsive Assorted Film Comprising Magnetic- and Gold-Nanoparticles with a Self-Assembly Protein of α-Synuclein

Development of sensing elements for controllable soft materials is crucial to improve their responsiveness toward remotely provided external stimuli. Magnetic nanoparticles (MNPs) and gold nanoparticles (AuNPs) have been coassembled into a flexible free-floating 2D film to produce a shape deformable mobile structure in the presence of magnetic field and light irradiation by employing a self-assembly protein of α-synuclein (αS). αS was demonstrated to be essential for the preparation of a multisensory system because the intrinsically disordered protein led to a complete dispersion of MNPs to an average size of 10 nm in aqueous solution, pH-dependent closely packed single layer adsorption of αS-MNPs, and α-helix-mediated free-floating MNP monolayer film formation upon dissolving the underlying polycarbonate substrate with chloroform. As AuNPs were incorporated into the assorted hybrid film in the presence of MNPs, however, the β-sheet component became prominent. By placing the assorted film between a spin-coated thin layer of thermoresponsive P(AAc-co-NIPAAm) hydrogel comprising acrylic acid and N-isopropylacrylamide and a passive layer of silicone elastomer, the resulting triply structure exhibited not only magnet-induced locomotion but also shape deformation due to asymmetric contraction of the sandwiching two layers caused by the heat generated by AuNPs upon near IR irradiation. In fact, two adjoining planar layers of another triply structure were shown to form a three-dimensional lotus flower with the light. This multisensory system is suggested to be further functionalized by modifying the αS molecules and incorporating additional nanoparticles to react to diverse stimuli, which would make the system be utilized in the areas of not only soft robotics but also foldable electronics, high-performance sensors/actuators, and medical/wearable applications.

Langmuir films of low-dimensional nanomaterials

A large number of low-dimensional nanomaterials having different shapes and being dispersible in solvents open a fundamental question if there is a universal deposition technique for the monolayer formation. A monolayer formation of various nanomaterials at the air-water interface, also known as a Langmuir film, is a well-established technique even for the large group of the recently developed low-dimensional nanomaterials. In this review, we cover the monolayer formation of the zero-dimensional, one-dimensional and two-dimensional nanomaterials. Thanks to the formation of a Langmuir layer at the thermodynamic equilibrium, by using a suitable nanomaterial dispersion and subphase, the monolayers can be formed from all kinds of materials, ranging from the graphene oxide to the semiconducting quantum dots. In this review, we will discuss the basic requirements for the successful formation of monolayers and summarize the recent scientific advances in the field of Langmuir films.

Constructing a library of metal and metal-oxide nanoparticle heterodimers through colloidal assembly

Nanoparticle dimers composed of different metals or metal oxides, as well as different shapes and sizes, are of wide interest for applications ranging from nanoplasmonic sensing to nanooptics to biomedical engineering. Shaped nanoparticles, like triangles and nanorods, can be particularly useful in applications due to the strong localized plasmonic hot-spot that forms at the tips or corners. By placing catalytic, but traditionally weakly- or non-plasmonic nanoparticles, such as metal oxides and metals like palladium, in these hot-spots, an enhanced function for sensing, photocatalysis or optical use is predicted. Here, we present an electrostatic colloidal assembly strategy for nanoparticles, incorporating different sizes, shapes and metal or metal oxide compositions into heterodimers with smaller gaps than are achievable using nanofabrication techniques. This versatile method is demonstrated on 14 combinations, including a variety of shaped gold nanoparticles as well as palladium, iron oxide, and titanium oxide nanoparticles. These colloidal nanoparticles are stabilized with traditional surfactants, such as citrate, CTAB, PVP and oleic acid/oleylamines, indicating the wide applicability of our approach. Heterodimers of gold and palladium are further analyzed using cathodoluminescence to demonstrate the tunability of these "plasmonic molecules". Since systematically altering the absorption and emission of the plasmonic nanoparticles dimers is crucial to extending their functionality, and small gap sizes produce the strongest hot-spots, this method indicates that the electrostatic approach to heterodimer assembly can be useful in creating new nanoparticle dimers for many applications.

Vibrational response of clusters of Fe3O4 nanoparticles patterned on glass surfaces investigated with magnetic sample modulation AFM

The vibration of Fe3O4 nanoparticles in response to an alternating magnetic field can be sensitively detected using contact mode atomic force microscopy (AFM) combined with selective modulation of magnetic domains. While imaging patterned samples of magnetic nanoparticles with contact mode AFM, a magnetic field was applied to drive sample vibration. The field altered in polarity and strength according to parameters of an AC current applied to a solenoid located under the sample. The vibration of Fe3O4 nanoparticles was detected by a nonmagnetic AFM tip to map the changes in frequency and amplitude of the vibrating sample at the level of individual Fe3O4 nanoparticles and clusters. Colloidal lithography, was used to prepare patterns of Fe3O4 nanoparticles on a glass surface using the basic steps of mixing, drying and removing the surface template of latex spheres. Monodisperse latex spheres were used to guide the deposition of magnetic nanoparticles in the spaces between the close-packed spheres of the latex film. With a mixture approach of "two-particle" lithography, 2D arrays of patterned aggregates of metal nanoparticles were generated which formed a periodic, well-defined arrangement that was suitable for subsequent characterizations with magnetic sample modulation (MSM).

Shell-binary nanoparticle materials with variable electrical and electro-mechanical properties

Nanoparticle (NP) materials with the capability to adjust their electrical and electro-mechanical properties facilitate applications in strain sensing technology. Traditional NP materials based on single component NPs lack a systematic and effective means of tuning their electrical and electro-mechanical properties. Here, we report on a new type of shell-binary NP material fabricated by self-assembly with either homogeneous or heterogeneous arrangements of NPs. Variable electrical and electro-mechanical properties were obtained for both materials. We show that the electrical and electro-mechanical properties of these shell-binary NP materials are highly tunable and strongly affected by the NP species as well as their corresponding volume fraction ratio. The conductivity and the gauge factor of these shell-binary NP materials can be altered by about five and two orders of magnitude, respectively. These shell-binary NP materials with different arrangements of NPs also demonstrate different volume fraction dependent electro-mechanical properties. The shell-binary NP materials with a heterogeneous arrangement of NPs exhibit a peaking of the sensitivity at medium mixing ratios, which arises from the aggregation induced local strain enhancement. Studies on the electron transport regimes and micro-morphologies of these shell-binary NP materials revealed the different mechanisms accounting for the variable electrical and electro-mechanical properties. A model based on effective medium theory is used to describe the electrical and electro-mechanical properties of such shell-binary nanomaterials and shows an excellent match with experiment data. These shell-binary NP materials possess great potential applications in high-performance strain sensing technology due to their variable electrical and electro-mechanical properties.

Effect of reaction environment and in situ formation of the precursor on the composition and shape of iron oxide nanoparticles synthesized by the thermal decomposition method

In this work, we investigate the effect of the reaction environment and the in situ formation of an iron precursor on the synthesis of iron oxide nanoparticles (IONPs) through thermal decomposition.

Enhanced Collective Magnetic Properties in 2D Monolayers of Iron Oxide Nanoparticles Favored by Local Order and Local 1D Shape Anisotropy

Magnetic nanoparticle arrays represent a very attractive research field because their collective properties can be efficiently modulated as a function of the structure of the assembly. Nevertheless, understanding the way dipolar interactions influence the intrinsic magnetic properties of nanoparticles still remains a great challenge. In this study, we report on the preparation of 2D assemblies of iron oxide nanoparticles as monolayers deposited onto substrates. Assemblies have been prepared by using the Langmuir-Blodgett technique and the SAM assisted assembling technique combined to CuAAC "click" reaction. These techniques afford to control the formation of well-defined monolayers of nanoparticles on large areas. The LB technique controls local ordering of nanoparticles, while adjusting the kinetics of CuAAC "click" reaction strongly affects the spatial arrangement of nanoparticles in monolayers. Fast kinetics favor disordered assemblies while slow kinetics favor the formation of chain-like structures. Such anisotropic assemblies are induced by dipolar interactions between nanoparticles as no magnetic field is applied and no solvent evaporation is performed. The collective magnetic properties of monolayers are studied as a function of average interparticle distance, local order and local shape anisotropy. We demonstrate that local control on spatial arrangement of nanoparticles in monolayers significantly strengthens dipolar interactions which enhances collective properties and results in possible super ferromagnetic order.

Substantial Difference in Ordering of 10, 15, and 20 nm Iron Oxide Nanoparticles on a Water Surface: In Situ Characterization by the Grazing Incidence X-ray Scattering

In the present study, for the first time, a unique combination of in situ grazing incidence small-angle X-ray scattering and X-ray reflectivity, accompanied by the pressure-area isotherm analysis, Brewster angle microscopy, and ex situ scanning electron microscopy, was applied for investigation of two-dimensional superlattices of magnetic nanoparticles as they form on a water surface in a Langmuir trough. Iron oxide particles of different sizes stabilized with a single layer of oleic acid were used. It is demonstrated that monodisperse 10 nm particles on a water surface reproducibly form identical highly ordered monolayers in a wide range of experimental conditions, while monodisperse 20 nm particles always form compact three-dimensional clusters and never the monolayers. Monodisperse particles of an intermediate size, 15 nm in diameter, build a metastable monolayer, which shows a tendency for spontaneous transformation to bi-, tri-, and multilayer islands. The importance to use both grazing incidence small-angle X-ray scattering and X-ray reflectivity together with the complementary techniques, to avoid misinterpretation of separate experimental data sets, is underlined.

Two dimensional dipolar coupling in monolayers of silver and gold nanoparticles on a dielectric substrate

The dimensionality of assembled nanoparticles plays an important role in their optical and magnetic properties, via dipolar effects and the interaction with their environment. In this work we develop a methodology for distinguishing between two (2D) and three (3D) dimensional collective interactions on the surface plasmon resonance of assembled metal nanoparticles. Towards that goal, we elaborate different sets of Au and Ag nanoparticles as suspensions, random 3D arrangements and well organized 2D arrays. Then we model their scattering cross-section using effective field methods in dimension n, including interparticle as well as particle-substrate dipolar interactions. For this modelling, two effective field medium approaches are employed, taking into account the filling factors of the assemblies. Our results are important for realizing photonic amplifier devices.

A 3D insight on the catalytic nanostructuration of few-layer graphene

The catalytic cutting of few-layer graphene is nowadays a hot topic in materials research due to its potential applications in the catalysis field and the graphene nanoribbons fabrication. We show here a 3D analysis of the nanostructuration of few-layer graphene by iron-based nanoparticles under hydrogen flow. The nanoparticles located at the edges or attached to the steps on the FLG sheets create trenches and tunnels with orientations, lengths and morphologies defined by the crystallography and the topography of the carbon substrate. The cross-sectional analysis of the 3D volumes highlights the role of the active nanoparticle identity on the trench size and shape, with emphasis on the topographical stability of the basal planes within the resulting trenches and channels, no matter the obstacle encountered. The actual study gives a deep insight on the impact of nanoparticles morphology and support topography on the 3D character of nanostructures built up by catalytic cutting.

The nanostructuration of graphene by catalytic cutting using iron oxide nanoparticles leads to the formation of well-defined trenches and tunnels. Here, the authors use electron microscopy to investigate this process in three dimensions and to gain insight into the formation and nature of these nanostructures.

The facile assembly of nanocrystals by optimizing humidity

Humidity and substrate properties are considered coordinately in the assembly of nano-sized crystals. The nanocrystal monolayers with thicknesses of 20–100 nm show large-area uniformity and excellent orientations.

Spacing-dependent dipolar interactions in dendronized magnetic iron oxide nanoparticle 2D arrays and powders

Self-assembly of nanoparticles (NPs) into tailored structures is a promising strategy for the production and design of materials with new functions. In this work, 2D arrays of iron oxide NPs with interparticle distances tuned by grafting fatty acids and dendritic molecules at the NPs surface have been obtained over large areas with high density using the Langmuir-Blodgett technique. The anchoring agent of molecules and the Janus structure of NPs are shown to be key parameters driving the deposition. Finally the influence of interparticle distance on the collective magnetic properties in powders and in monolayers is clearly demonstrated by DC and AC SQUID measurements. The blocking temperature T(B) increases as the interparticle distance decreases, which is consistent with the fact that dipolar interactions are responsible for this increase. Dipolar interactions are found to be stronger for particles assembled in thin films compared to powdered samples and may be described by using the Vogel Fulcher model.

Co-tunneling enhancement of the electrical response of nanoparticle networks

A co-tunneling charge-transfer process dominates the electrical properties of a nanometer-sized "slice" in a nanoparticle network, which results in universal scaling of the conductance with temperature and bias voltage, as well as enhanced spintronics properties. By designing two large (10 μm) electrodes with short (60 nm) separation, access is obtained to transport dominated by charge transfer involving "nanoslices" made of three nanoparticles only. Magnetic iron oxide nanoparticle networks exhibit a magnetoresistance ratio that is not reachable by tunneling or hopping processes, thereby illustrating how such a size-matched planar device with dominant co-tunneling charge-transfer process is optimal for realizing multifunctional devices with enhanced change of conductance under external stimulus.